Ford 2011 Explorer v.1- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

Notice to owners of pickup trucks and utility type vehicles WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully.Your vehicle is not a passenger car. As with other vehicles of this ty...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only) the service uses GPStechnology and advanced vehicle sensors to collect the vehicle’scurrent location, travel direction, and speed (“vehicle travelinformation”) only to help provide you with the directions, ...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Base instrument cluster with standard measure shown; metricsimilar Optional instrument cluster with standard measure shown; metricsimilar Warning lights can alert you to a vehicle condition that may becomeserious enough to cause extensive repairs. A warning light mayillumin...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on positionwhen the engine is not running, or in a position between on and start, orby applying the parking brake when the ignition is turned to the onp...

Engine coolant temperature: Illuminates when the engine coolanttemperature is high. Stop thevehicle as soon as possible, switch off the engine and let cool. Refer to Engine coolant in the Maintenance and Specifications chapter. WARNING: Never remove the coolant reservoir cap while the engine is runn...

GAUGES Base clusterShown in standard measure. Metric similar. 1. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scalemay damage the engine. 2. Multifunction display: This displays the engine coolant temperature, 4...

Optional clusterShown in standard measure. Metric similar. 1. Multifunction display: This displays the fuel gauge, tachometer, engine coolant temperature, odometer/trip meter and other vehiclefeatures. This is also used to configure different vehicle personalizationoptions and display the status of ...

The message center is also used to program/configure the differentfeatures of your vehicle. The message center display is located in theinstrument cluster. Use the left steering wheel controls to navigate through the message center. • Press the up/down arrow buttonsto move up/down through themessage...

Settings (cont’d) MyKey Create MyKey™ Hold OK to Create MyKey Traction Control Always On or User Selectable Max Speed 80 MPH (130 km/h) or Off Speed Warning 45 mph (75 km/h), 55 mph(90 km/h), 65 mph (105 km/h) orOff Volume Limiter Clear MyKeys Hold OK to Clear MyKeys System Reset Hold OK toReset Sys...

Menu Control: You can choose a different menu control operation tosuite your needs. In any screenwhich shows these category icons(other than the Main menu screen)and: • Standard is set– then scrolling up and down will scroll through themain categories. • Memory on is set– then scrolling up and down ...

• Fuel gauge: Indicates approximately how much fuel is left in the fueltank. The fuel gauge may vary slightly when the vehicle is in motionor on a grade. When the fuel level becomes low (50 miles [80 km] toempty), the level indicator will change to amber. When the fuel levelbecomes critically low (0...

Enhanced trip display • Trip distance — shows the accumulated trip distance • Average fuel economy — shows the average fuel economy for a giventrip. • Estimated amount of fuel consumed — shows the amount of fuel usedfor a given trip. • Elapsed trip time — timer stops when the vehicle is turned off a...

Settings In this mode, you can configure different driver setting choices. Pressthe right arrow key (when in the Settings menu) to reach the listedmodes below: Note: Some items are optional and may not appear. Driver Assist Traction Control On / Off Blind Spot On (default on key cycle) / Off Collisi...

Units Distance Miles & Gallons / Kilometers & Liters Temperature Fahrenheit (°F) / Celsius (°C) Restore defaults Hold OK to Restore Settings to Factory Defaults Information In this mode, you can view different vehicle system information andperform a system check. When Press OK for info is di...

MYFORD™ SYSTEM (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperatio...

2. You can press some of the hard buttons to access their respectivemenus. 3. Use the center control in thesame manner you would a joystick— press / to move up/down in menus or press / to move out of or into a menu. When theseoptions are available, icons willappear on the screen. 4. Press OK on the ...

• Press / to seek to the previous/next channel within the selected category. • To save a channel as a preset, acquire the desired channel and thenpress and hold the desired memory preset (0–9). A pop-up screen willconfirm when it is saved. • To view your presets, press / / for a list of your saved p...

3. Turn your portable music player on and adjust the volume to 1/2 offull volume. 4. Press AUX repeatedly until Auxiliary audio active or Line in active appears. 5. Now adjust the volume on your portable music player until it matchesthat of the FM station or the CD you were listening to previously. ...

SINGLE ZONE MANUAL SYSTEM WITH REAR CLIMATECONTROLS (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius: Press MENU > Display Settings > Temp. Setting, or refer to Settings in the Message Center section of the Instrument Cluster chapter. 1. (Fan speed adjustment): Tu...

5. (Multifunction control): Press repeatedly to toggle through the settings and manually choose one of the following air distribution modes: • : Distributes air through the windshield defroster vents, de-mister vents, floor vents and rear seat floor vents. The system willautomatically provide outsid...

Operating tips • To reduce fog build-up on the windshield during humid weather,select (defrost) or (floor/defrost). • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or with (recirculated air) engaged and A/C off. • Do not put objects under the front seats that will i...

AUTOMATIC TEMPERATURE CONTROL SYSTEMS Dual Automatic Temperature Control (DATC) Sony system(if equipped) Note: Your climate control system is touch sensitive. You need only lightly touch the control graphic to activate the feature. Note: Your vehicle is also equipped with touchscreen climate control...

3. (Recirculated air): Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time to cooldown the interior of the vehicle and may also help reduce undesiredodors from reaching the interior of the vehicle. Recirculated air engagesautomatically when M...

3. MAX A/C: Distributes recirculated air through the instrument panel vents to cool the vehicle. This re-cooling of the interior air is moreeconomical and efficient. Recirculated air may also help reduceundesirable odors from entering the vehicle. Touch MAX A/C again fornormal A/C operation. 4. A/C ...

Operating tips • To reduce fog build-up on the windshield during humid weather,select (defrost) or (floor/defrost). • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or with (recirculated air) engaged and A/C off. • Do not put objects under the front seats that will i...

11. Driver settings: • Press the red arrow to increase the temperature and press the bluearrow to decrease the temperature. • Press to control the heated seat (if equipped). Refer to Heated seats in the Seat and Safety Restraints chapter. • Press and hold MyTemp to select a temperature you would lik...

• Rear Defrost On • Rear Defrost Off • Recirc On • Recirc Off • Panel On • Panel Floor On • Floor On • Windshield Floor On • Temperature High • Temperature Low • Fan Increase • Fan Decrease • Temperature • Temperature Increase • Temperature Decrease • Temperature <15.5–29.5> degrees • Temperat...

CABIN AIR FILTER The cabin air filter element is designed to reduce the concentration ofairborne particles such as dust, spores and pollen in the air beingsupplied to the interior of the vehicle. The presence of a particulate filterelement provides the following benefits: • Improves your driving com...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

3. Rotate the headlamp control to the off position. 4. Turn the vehicle on. 5. Turn the vehicle off. 6. Turn the headlamp control to the autolamp position (the headlightsshould turn on). 7. Turn the headlamp control to the off position when the desired delaytime (up to three minutes) has been reache...

Daytime running lamps (DRL) (if equipped) To activate DRL: • the ignition must be in the on position and • the headlamp control is in the or position • the transmission is not in P (Park). WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lig...

Dome lamp control Use to manually turn the dome lampon. • Press the control. This will turnon the interior courtesy lights.The lights will remain on until thecontrol is pressed again. Dome lamp control (with fog lamps) Use to manually turn the dome lampon. • Press the bottom of the control.This will...

5. Locate the vertical adjuster foreach headlamp. Using a Phillips #2screwdriver, turn the adjustercontrol either clockwise (to adjustdown) or counterclockwise (toadjust up). Note: HORIZONTAL AIMING IS NOT REQUIRED FOR THISVEHICLE AND ISNON-ADJUSTABLE. TURN SIGNAL CONTROL The turn signal lever does ...

INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerbutton is pressed until thecourtesy lamp comes on. • the remote entry controls arepressed and the ig...

Third row cargo lamp The dome lamp lights when: • any door is opened. • the instrument panel dimmerbutton is pressed until thecourtesy lamp comes on. • any of the remote entry controlsare pressed and the ignition isoff. The courtesy lamp can also beturned on and off manually bypressing the control s...

Replacing exterior bulbs Check the operation of all the bulbs frequently. Replacing headlamp bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. Remove the bulb cover. 4. Turn the bulb holdercounterclockwise and remove it. 5. Disconnect the electrical connector....

Replacing front parking lamp/turn signal bulbs 1. Make sure that the headlampcontrol is in the off position. 2. Open the hood. 3. Remove the hood overslambumper tower to service park/turnbulb (if needed). 4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly. 5. Pull the bulb...

Replacing sidemarker bulbs 1. Make sure that the headlampcontrol is in the off position. 2. Open the hood. 3. Remove the hood overslambumper tower to service sidemarkerbulb (if needed). 4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly. Lights 88 2011 Explorer (exp) Owner...

5. Pull the bulb straight out of thesocket. Reverse steps to reinstall bulb(s). Replacing turn/backup lamp bulbs The turn/backup lamp bulbs are located in the same area of the tail lampassembly, one below the other. Follow the same steps to replace thesebulbs: 1. Make sure the headlamp switch isin t...

WINDSHIELD WIPERS Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers (ifequipped): When the wiper control is set to any of the interval settings except the longest pause settin...

Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick press and hold: thewipers will swipe three times withwasher fluid. • a long press and hold: the wipersand washer fluid will be activated for up to ten seconds. Note: Do not op...

Reverse wiper feature: The rear wiper will be automatically activated in an intermittent setting when shifting into R (Reverse) if the front wipersare activated. This feature may be enabled/disabled through the messagecenter. Refer to Message center in the Instrument Cluster chapter. TILT/TELESCOPE ...

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment The storage compartment may beused to store a pair of sunglasses.Press the release area on the rearedge of the bin door to open thestorage compartment. The door willopen ...

Rear center console features (if equipped) The rear center console incorporates the following features: • Flip forward armrest to provide aflat load floor • Utility compartment • Cupholders AUXILIARY POWER POINTS (12V DC) Power outlets are designed for accessory plugs only. Do not insertany other ob...

One-touch up or down This feature allows the driver’s window (and passenger’s window, if equippedwith this feature) to open or close fully without holding the control down. To operate one touch-down, press the switch completely down to thesecond detent and release quickly. The window will open fully...

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side. WARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror (if equipped) The interior rear view m...

EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Press the left or right mirrorbutton to select the mirror to beadjusted. An indicator light on thebutton will illuminate. 2. Use the control below the mirrorbuttons t...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. The control is located on the leftside of the steering column. Pressand hold the rear of the control tomove the pedals towa...

Turning off speed control To turn off the speed control, press OFF downward or turn off the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. ADAPTIVE CRUISE CONTROL (ACC) (IF EQUIPPED) Adaptive cruise control (ACC) is much like speed...

Using adaptive cruise control Note: It is the drivers responsibility to stay alert, drive safely and be in control of the vehicle at all times. The controls for using your cruisecontrol are located on the steeringwheel. SET: Press to set a speed or to change the set speed. RES/CNCL (Resume/cancel): ...

Following a vehicle WARNING: When following a vehicle in front of you, the vehicle will not decelerate automatically to a stop, nor will the vehicle always decelerate quickly enough to avoid a collision without driverintervention. Always apply the brakes when necessary. Failing to do somay result in...

Cause Action The surface of the radar in the grilleis dirty or obstructed in some way Clean the grille surface in front ofthe radar or remove the objectcausing the obstruction The surface of the radar in the grilleis clean but the message remains inthe display Wait a short time. It may takeseveral m...

UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED) Your vehicle may be equipped with a universal garage door opener whichcan be used to replace the common hand-held transmitter. Car2U 姞 Home Automation System (if equipped) The Car2U 威 Home Automation System is a universal transmitterlocated in the driver’s ...

POSITIVE RETENTION FLOOR MAT WARNING: Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that theeyelets are over the retention postsand press down to lock in. Makesure that the mat...

Utility hook The utility hook can be used tohang small items such as grocerybags, etc. Do not hang more than10 lb (4.5 kg) on the hook. MANUAL LIFTGATE (IF EQUIPPED) The liftgate area is only intended for cargo, not passengers. To open the liftgate, press thebutton located in the top of theliftgate ...

If the liftgate reverses and starts to close after an open request, a fastcontinuous chime indicates excessive load on the gate or a possible strutfailure. If any excessive load is removed and you still have a fasterchime, have the system serviced immediately by your authorized dealer. Do not attemp...

To power open the liftgate withoutside liftgate control button: 1. Unlock the liftgate with thetransmitter or power door unlockcontrol. If the intelligent accesstransmitter (if equipped) is within3 feet (1 meter) of the liftgate, theliftgate will unlock when you pressthe liftgate release button. 2. ...

The new open liftgate height will now be recalled when the powerliftgate is opened. To change the programmed height, repeat the aboveprocedure. Once the power liftgate is opened it can be manually movedto a different height. Note: Do not drive with the liftgate open without first disabling the power...

2. Slide the crossbar to the desired position. This may require someoneon each side of the crossbar. 3. Tighten the tie-down hooks at both sides of the crossbar by turningclockwise until tight. (A small screwdriver or similar tool can be used totighten the hook an additional half turn.) Be sure to c...

KEYS Integrated keyhead transmitters (IKTs) (if equipped) Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unlocks/locks thedriver’s door. The transmitterportion functions as the remoteentry transmitter...

MYKEY™ The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehicle can be activated as a MyKey™. The key will remain restricteduntil MyKey™ is cleared. Any remaining keys are referred to as an“administrator key” o...

Create a MyKey™ To program MyKey™ on one of the keys programmed to the vehicle,insert the key that you want to make a MyKey™ into the ignition. Forvehicles equipped with push button start, put the intelligent access keyin the backup slot with brand logo facing up; see the Driving chapter for the loc...

Check MyKey™ system status The vehicle’s message center information menu will provide the status ofthe following MyKey™ parameters: • MYKEY MILES (km) — This odometer only tracks distance when aMyKey™ is used. If distance does not accumulate as expected, thenthe MyKey™ is not being used by the inten...

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Smart unlocks for integrated keyhead transmitter (IKT) This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open one of the front doors...

CHILDPROOF DOOR LOCKS • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when thechildproof door locks are set, butthe doors are unlocked. The childproof locks are located onthe rear edge of each rear door andmust be set separate...

The transmitter allows you to: • remotely unlock the vehicle doors . • remotely lock all the vehicle doors . • remotely open the power liftgate (if equipped) . • remotely start/stop the vehicle (if equipped) . Refer to Remote start later in this section. • activate the personal alarm . • arm and dis...

To lock the doors, press and hold for half a second the lock area (blackbutton) on either front door handle. Activating intelligent access at the liftgate: If your IA key is within 3 feet (1 meter) of the liftgate, you can activate your intelligent accesssystem by pressing the exterior liftgate rele...

Programming the memory feature to the transmitter To activate this feature: 1. Move the driver seat and power mirrors to the desired positions usingthe associated controls. 2. Press and hold button 1 for fiveseconds. A tone will be heard afterabout two seconds confirmingmemory position has been set....

Replacing the battery The integrated keyhead transmitter (IKT) or intelligent access key (IAkey) uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: Integrated keyhead transmitter (IKT) 1. Twist a thin coin in the slot nearthe key ring to remove the batterycov...

2. Remove the old battery. Note: Please refer to local regulations when disposing oftransmitter batteries. 3. Insert the new battery. Refer tothe instructions inside the IA keyfor the correct orientation of thebattery. Press the battery down toensure that the battery is fullyseated in the battery ho...

Illuminated exit When all vehicle doors are closed, the ignition is turned off and the keyis removed from the ignition (IKT only), the interior dome lamps,parking lamps and the puddle lamps (if equipped) will illuminate. The lamps will turn off if all the doors remain closed and • 25 seconds elapse,...

To help make the vehicle as comfortable as possible, the engine idle canbe increased during a remote start. You can enable or disable engine idleincrease by selecting Remote Start Quiet in the message center. Refer to Message center in the Instrument Cluster chapter. Many states and provinces have r...

Note: If the vehicle has been remote started and is equipped with an IKT, you must turn the ignition on before driving the vehicle. If equippedwith an IA transmitter, you must press the START/STOP button on theinstrument panel once while applying the brake pedal before driving thevehicle. The power ...

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • recall memory seat/power mirrorspositions (if equipped). • enable/disable autolock andautounlock. • program/erase user codes. • arm/disarm the perimeter alarmsystem...

Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personalcode. Erasing personal code 1. Enter the factory set 5–digit code.2. Within five seconds, press the 1 • 2 on the keypad a...

SECURILOCK 姞 PASSIVE ANTI-THEFT SYSTEM SecuriLock 威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded integrated keyhead transmitter (IKT) or intelligent access keys programmed to your vehicle is used. Th...

Replacement of integrated keyhead transmitters (IKT) or intelligentaccess keys Note: Your vehicle comes equipped with two integrated keyhead transmitters (IKTs) or two intelligent access keys. The integrated keyhead transmitter (IKT) functions as both a programmed ignition key that operates all the ...

• If two previously programmed coded keys are not available, you musttake your vehicle to your authorized dealer to have the spare key(s)programmed. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition. 2. Turn the ig...

8. Verify that the remote entry functions operate (press lock thenunlock, making sure you end in unlock) and that the vehicle starts withnew intelligent access key. If the intelligent access key has been successfully programmed, it can beused to activate the intelligent access with push button Start...

2. Pivot the head restraint forwardtowards your head to the desiredlocation. After the head restraint reachesthe forward-most tilt position,pivoting it forward again will thenrelease it to the rearwardun-tilted position. Adjusting the front manual seat (if equipped) WARNING: Never adjust the driver’...

Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the controlto adjust firmness. Press the rearward side of thecontrol to adjust softness. Dual setting heated seats (if equipped) The heated seats will only fun...

To install a filter: 1. First, position the filter in itshousing making sure that the farforward end is all the way up in thehousing. 2. Push in on the center of theoutside edge of the filter and rotateup into the housing until it clips intoposition. Memory feature (if equipped) This system allows a...

REAR SEATS Second row head restraints Your vehicle may be equipped with two types of second row headrestraints: • Outboard seat head restraints– The outboard head restraints are not vertically adjustable, but they can be folded and also removed. To fold the outboard head restraint,pull the release s...

Adjusting second row bucket and bench seat back Lift the handle to adjust seatback.Using same control will fold theseatback flat. Note: For the bench seat only, make sure the center safety belt isunbuckled before folding theseatback. WARNING: Always drive and ride with your seatback upright and the ...

2nd row power fold and tumble seat (six–passenger vehicles only) WARNING: Ensure that the seat is unoccupied when folding it down. Folding the seat while occupied could result in occupant injury or damage to the seat. Press the control located at theback of the rear door opening onetime to fold the ...

3. To return the seatback to thefloor from tumbled position, rotatethe seat down until you hear itlatching to the floor. 4. To return the seatback to theupright position • Lift the seatback toward the rearof the vehicle, and • Rotate the seatback until youhear a click, locking it in theupright posit...

• Passenger airbag off/on indicator lamp • Front crash severity sensors. • Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and backup tone. • The electrical wiring for the airbags, crash sensor(s), safety beltpretensioners, front safety belt usage sen...

Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System totailor the deployment level of the driver dual-stage airbag based on seatposition. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower airbag...

Restraint of pregnant women WARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. Theshoulder portion of the safety belt should be positioned across thechest. Pregnant...

Automatic locking mode In this mode, the shoulder belt or lap belt is automatically pre-locked.The belt will still retract to remove any slack in the shoulder or lap belt.The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode This mode should be...

How to disengage the automatic locking mode WARNING: After any vehicle collision, the safety belt system at all passenger seating positions must be checked by an authorized dealer to verify that the “automatic locking retractor” feature for childseats is still functioning properly. In addition, all ...

Rear Inflatable Safety Belt (if equipped) The rear inflatable safety belts arefitted in the shoulder safety belts ofthe second-row outboard seatingpositions. Note: The rear inflatable safety belts are compatible with infant andchild safety car seats and beltpositioning booster seats. The rear inflat...

How does the rear inflatable safety belt system work? • The rear inflatable safety beltswill function like standardrestraints in everyday usage. • During a collision of sufficientforce, the inflatable belt willdeploy. The shoulder portion ofinflatable belt will inflate awayfrom the neck and face. • ...

WARNING: Do not use extensions with an inflatable safety belt. WARNING: Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt height adjustment Your vehicle has safety belt heightadjustments for the front outboardseating positions. Adjust the height of the should...

If... Then... The driver’s or front passenger’ssafety belt becomes unbuckledfor approximately one minutewhile the vehicle is traveling atleast 3 mph (5 km/h) and morethan 1-2 minutes have elapsedsince the ignition switch hasbeen turned to on... The Belt-Minder 威 feature is activated - the safety bel...

Reasons given... Consider... “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’t wearbelts” Set the example, teen deaths occur 4times more often in vehicles with TWOor MORE people. Children an...

WARNING: Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system,increasing the risk of injury. Do not modify the front end of thevehicle. Children and airbags Children must always...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• a readiness light and tone. • diagnostic module. • the electrical wiring which connects the components. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing sy...

Passenger airbag status indicator The front passenger sensing systemuses a passenger airbag statusindicator which will illuminateindicating that the front passengerfrontal airbag is either ON (enabled)or OFF (disabled). The indicatorlamp is located in the center stackof the instrument panel. Note: T...

• Objects stowed in the seatback map pocket (if equipped) • Objects placed on the occupant’s lap • Cargo interference with the seat • Other passengers pushing or pulling on the seat • Rear passenger feet and knees resting or pushing on the seat The conditions listed above may cause the weight of a p...

Seat-mounted side airbag system WARNING: Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with adeploying airbag. Failure to follow these instructions may increase therisk of personal...

How does the Safety Canopy 姞 System work? The design and development of theSafety Canopy system includedrecommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk of...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your an authorized dealer immediately. Unless serviced, the systemmay not function properly in the ev...

WARNING: All children are shaped differently. The Recommendations for Safety Restraints are based on probable child height, age and weight thresholds from NHTSA and other safetyorganizations or are the minimum requirements of law. Fordrecommends checking with a NHTSA Certified Child Passenger Safety...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Installing child safety seats with combination lap and shoulderbelts Check to make sure the child seat is properly secured before each use.Children 12 and under should be properly restrained in a rear seatingposition whenever possible. If all children cannot be seated andrestrained properly in a rea...

Perform the following steps when installing the child seat withcombination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in aseat with a combination lap a...

WARNING: The standardized spacing for LATCH lower anchors is 280 mm (11 inches) center to center. Do not use LATCH lower anchors for the center seating position unless the child seatmanufacturer’s instructions permit and specify using anchors spaced atleast as far apart as those in this vehicle. Eac...

Perform the following steps to attach a child safety seat to the tetheranchor: Second row seating positions 1. Route the child safety seat tetherstrap over the seatback, under thehead restraint, and between thehead restraint posts. 2. Locate the correct anchor for the selected rear seating position....

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

VEHICLE CHARACTERISTICS Four-wheel drive (4WD) system (if equipped) A vehicle equipped with 4WD (when selected) has the ability to use allfour wheels to power itself. This increases traction which may enable youto safely drive over terrain and road conditions that a conventionaltwo-wheel drive vehic...

How your vehicle differs from other vehicles SUVs and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your vehicle maybe: • Higher – to allow higher loadcarrying capacity and to allow itto travel over rough terrainwithout getting hung up ordamaging underbody components. • Shorter ...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increasedrisk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat buildup a...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance Guide chapter) will help your tires wear more evenly, providing better tire...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h)...

11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label, which is located on the B-Pillar or the edge of thedriver’s door, for the correct tire pressure for your vehicle. 12. Treadwear, Traction and Tempe...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The ...

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, refer to Changing tires with a TPMS in this section. When you believe your system is not operating properly The main function o...

Low tire pressurewarning light Possiblecause Customer action required Flashing warninglight Spare tire inuse Your temporary spare tire is in use.Repair the damaged road wheel andre-mount it on the vehicle to restoresystem functionality. For adescription of how the systemfunctions under these conditi...

SNOW TIRES AND CABLES WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lb.” on your vehicle’s plac...

TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer towoption package. An optional Class III towing hitch is available and may berequired for your towing purposes. Trailer towing puts additional loads on your vehicle’s engine,transmission, axle, brakes, tires and suspens...

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The trailer brakes must meet local and Federalregulations. WARNING: Do not connect a trailer’s hydraulic brake system directly to your veh...

Trailer towing tips • Practice turning, stopping and backing-up before starting on a trip toget the feel of the vehicle-trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • To aid in engine/transmission cooling and A/C efficiency during hot...

STARTING Positions of the ignition (if equipped) If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. 1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessorie...

Note: Cranking may be stopped at any time by turning the key to the off position. 3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive. Note: If the engine does not start on the first try, turn the vehicle to the off position, wait 10 seconds and tr...

3. On — press and hold the START/STOP button for at least one secondwithout applying the brake pedal. This will power your vehicle’s electricalsystem and the warning lights in the instrument cluster will illuminate,but the engine will remain off. Note: You can start the engine from any ignition mode...

Switching the vehicle off when not in P (Park): It is recommended that you shift into the P (Park) position before switching your vehicleoff. If you switch your vehicle off with the shifter in any position otherthan P (Park), the message SHIFT TO PARK will be displayed in themessage center. If the v...

brake pedal may suddenly travel a little farther as soon as ABS braking isdone and normal brake operation resumes. These are normalcharacteristics of the ABS and should be no reason for concern. Using ABS When hard braking is required, apply continuous force on the brakepedal. Do not pump the brake ...

the parking brake, and then inspect the accelerator pedal for anyinterferences. If none are found and the condition persists, have yourvehicle towed to the nearest dealer. Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down ...

Turning traction control off If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off traction control in the AdvanceTrac 威 with RSC 威 system may be beneficial because the wheels are allowed to spin. Thiswill restore full engine power and will enhance momentum throu...

HILL DESCENT CONTROL™ (IF EQUIPPED) Hill descent control allows the driver to set and maintain vehicle speedwhile descending steep grades in various surface conditions. WARNING: Hill descent control cannot control descent in all surface conditions and circumstances, such as ice or extremely steep gr...

Note: Noise from the ABS pump motor may be observed during hill descent control operation. This is a normal characteristic of the ABS andshould be no reason for concern. Hill descent modes • At speeds below 20 mph (32 km/h): When the HDC button is pressedand HDC is active, HILL DESCENT CONTROL ACTIV...

BRAKE-SHIFT INTERLOCK This vehicle is equipped with a brake-shift interlock (BSI) feature thatprevents the gearshift lever from being moved from P (Park) when theignition is in the on position unless the brake pedal is pressed. If you cannot move the gearshift lever out of P (Park) with ignition int...

P (Park) This position locks the transmissionand prevents the front wheels fromturning. To put your vehicle in gear: • Press the brake pedal • Move the gearshift lever into thedesired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in ...

The tow feature delays upshifts to reduce frequency of transmissionshifting. Tow also provides engine braking in all forward gears when thetransmission is in the D (Overdrive) position. This engine braking willslow the vehicle and assist the driver in controlling the vehicle whendescending a grade. ...

• The grade assist lamp in theinstrument cluster is illuminated. Grade assist is designed to aid thedriver with optimal gear selection inhilly terrain or mountainous areasbut is not intended for normal operation. It is recommended that youreturn to O/D (overdrive mode) on flat terrain to provide the...

Recommended shift speeds Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 15 mph (24 km/h) 2 - 3 25 mph (40 km/h) 3 - 4 40 mph (64 km/h) 4 - 5 45 mph (72 km/h) 5 - 6 50 mph (80 km/h) The message center display in the instrumen...

Using hill start assist The hill start assist feature is activated automatically when the vehicle isstopped on a slope greater than five degrees. The hill start assist featureoperates with the vehicle facing downhill if reverse gear is selected. Thehill start assist feature will not operate if the p...

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rear video camera system,located on the liftgate above thelicense plate, provides a video imageof the area behind the vehicle. Itadds assistance to the driver whilereversing or reverse parking thevehicle. To use the rear videocamera system, place thetransmiss...

To use active guidelines, turn the steering wheel and point the activeguidelines towards an intended path. If the steering wheel position ischanged while reversing, the vehicle might deviate from the originalintended path. Active guidelines project the intended path of the vehicle. Fixedguidelines s...

When enabled, Level 1, Level 2, or Level 3 will only be active while thevehicle is in R (Reverse). The feature disables outside of R (Reverse)and must be re-enabled the next time the vehicle shifts into R (Reverse). When manual zoom is enabled, onlythe centerline will be shown. Rear camera delay Aft...

Night time and dark area use At night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore, it is necessary that bothreverse lamps are operating in order to get a clear image in the dark. Ifeither of the lamps are not operating, stop using the ca...

Operation The radar sensor detects vehiclesahead that are moving in the samedirection as your vehicle. If the radar detects that yourvehicle is rapidly closing on anothervehicle a red warning light willilluminate and an audible warningchime will sound. After that, if the risk of collisionfurther inc...

WARNING: The collision warning system’s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’s brakes. The brake pedal must be pressedjust like for any typical braking situation. Blocked sensor If a message regarding a blockedsensor is displayed,...

Activating/deactivating collision warning system To turn the warning system and/or chime on or off and set the warningsensitivity <– –>, refer to Message center in the Instrument Cluster chapter. Note: If the system cannot be turned off in a MyKey™ equipped vehicle, refer to MyKey™ in the Lock...

Automatic search for parking space To start, press the APA controlswitch (on the left side of theinstrument panel below theheadlamp switch). The touch screenwill display SEARCHING FORPARKING SPACE ON RIGHT(LEFT/SIDE) and a correspondinggraphic. To designate what side ofthe street to search on, use t...

Automatic steering into parking space Automatic steering is activated when you stop the vehicle, remove yourhands from the steering wheel and select the R (Reverse) gear. Be surethe steering wheel motion is not obstructed by any objects. The vehiclewill steer itself from this point on as you follow ...

The system should not be used if: • a foreign object (i.e. bike rack, trailer, etc.) is attached to the front orrear of the vehicle or at another location close to the sensors. • the front bumper or side sensors are damaged (i.e. in a collision) orobstructed by a foreign object (i.e. front bumper co...

BLIND SPOT MIRRORS (IF EQUIPPED) Blind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors. They are designed toassist the driver by increasing visibility along the side of the vehicle. Formore information on your side view mirrors, refer ...

BLIND SPOT INFORMATION SYSTEM (BLIS 姞 ) WITH CROSS TRAFFIC ALERT (CTA) (IF EQUIPPED) The BLIS 威 is a convenience feature that aids the driver in assessingwhether a vehicle is within an areaon either side of the vehicleextending rearward from the outsidemirrors to approximately 10 feet(3 meters) beyo...

Cross traffic alert (CTA) system operation The CTA system warns the driver of approaching vehicles when R(Reverse) is selected and the vehicle is backing out of a front-in parkingspot. It sounds a series of tones and flashes the BLIS 威 indicator found on the exterior mirror on the side of the approa...

CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed for vehicle on left] ). CTA detection limitations: Due to the nature of radar technology, there may be certain instances where vehicles entering and exiting theblind spot...

CTA and reverse sensing system (RSS) interaction CTA works along with the reverse sensing system (RSS) (if equipped).Become familiar with the warning tones of both systems. BLIS 威 and/or CTA on/off and disable operation The BLIS 威 and/or the CTA can be turned off via the message center. If either th...

FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) WARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. Your vehicle is equipped with an intelligent 4WD system thatcontinuously monitors vehicle conditions and automatically...

Basic operating principles • Drive slower in strong crosswinds which can affect the normal steeringcharacteristics of your vehicle. • Be extremely careful when driving on pavement made slippery byloose sand, water, gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehi...

WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may no...

Sand When driving over sand, try to keep all four wheels on the most solidarea of the trail. Avoid reducing the tire pressures but shift to a lowergear and drive steadily through the terrain. Apply the accelerator slowlyand avoid spinning the wheels. Avoid excessive speed because vehicle momentum ca...

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness areas. Ford MotorCompany joins the U.S. Forest Service and the Bureau of LandManagement in encouraging you to help preserve our national forest andother ...

TERRAIN MANAGEMENT SYSTEM FAULT: If this message is displayed, cycling the key may clear the fault. If the fault is not clearedafter a key cycle, have the system serviced by an authorized dealer. MODE CHANGE NOT ACCEPTED, RETRY: If this message is displayed, a vehicle system cannot support a mode ch...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours, seven days a week • for the...

Canadian customers refer to your Warranty Guide or visit ourwebsite at www.ford.ca for information on: Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio i...

FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fuel to theengine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision due to this feature, you mayrestart your vehic...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses 2A Grey Grey — — 3A Violet Violet — — 4A Pink Pink — — 5A Tan Tan — — 7.5A Brown Brown — — 10A Red Red — — 15A Blue Blue — — 20A Yellow Yellow Yellow Blue 25A Natural Natural — — 30A G...

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A One touch up/down driver side frontwindow 2 15A Not used (spare) 3 30A One touch up/down passenger side frontwindow 4 10A Interior demand lamps (overheadconsole, 2nd row, cargo), glove box lamp,2nd and 3rd r...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To red...

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 94 30A** Passenger compartment fuse panelrun/start 95 — Not used 96 — Not used 97 — Not used 98 — A/C clutch relay *Mini Fuses **Cartridge Fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heav...

3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the d...

Stopping and securing the vehicle 1. Park on a level surface, set theparking brake and activate hazardflashers. 2. Place gearshift lever in P (Park)and turn engine off. Removing the spare tire and jack If the 3rd row seat is stowed in the floor, you will need to unstow it (raisedposition) to access ...

Tire change procedure WARNING: When one of the front wheels is off the ground, the transaxle alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park). WARNING: To help prevent the vehicle from moving when you change a tire, be sure to place the tran...

1. Air compressor (inside) 2. Diverter knob 3. On/Off button 4. Air pressure gauge 5. Deflation button 6. Sealant bottle/canister 7. Sealant filling clear tube 8. Sealant tube — tire valveconnector 9. Yellow cap tool 10. Air compressor hose 11. Air hose — tire valve connector 12. Accessory power plu...

Tips for use of the temporary mobility kit Read the following list of tips to ensure safe operation of the temporarymobility kit: • Before operating the temporary mobility kit, make sure your vehicle issafely off the road and away from moving traffic. Turn on the hazardlights. • Always set the parki...

10. Immediately and cautiously, drive the vehicle 4 miles (6 km) to distribute the sealant evenly inside the tire. Do not exceed50 mph (80 km/h). Note: If you experience any unusual vibration, ride disturbance or noise while driving, reduce your speed until you can safely pull off tothe side of the ...

5. Turn the compressor off by pressing the on/off button. 6. Unplug the hoses, re-install the valve cap on the tire and return thekit to the stowage area. WARNING: The power plug may get hot after use and should be handled carefully while unplugging. What to do after the tire has been sealed After u...

WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum orbrake disc that contacts the wheel. Ensure that any fasteners thatattach the rotor to the hub are secured so they do ...

JUMP STARTING WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your aut...

Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+)...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the FordMotor Company Customer Relationship Center at 1-800-392-3673. Note: F...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The highpressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

LEATHER SEATS FOR THE KING RANCH 姞 EDITION ONLY (IF EQUIPPED) Your vehicle is equipped with seating covered in premium, top-grainleather which is extremely durable, but still requires special care andmaintenance in order to ensure longevity and comfort. Regular cleaning and conditioning will maintai...

SERVICE RECOMMENDATIONS • Use the scheduled maintenance information to track routine service. • Use only recommended fuels, lubricants, fluids and service partsconforming to specifications. • Your authorized dealer can provide parts and service. PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work ...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance and Specifications 376 2011...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 engine 1. Engine coolant reservoir 2. Brake fluid reservoir 3. Battery 4. Power distribution box 5. Air filter assembly 6. Transmission fluid dipstick (out of view) 7. Engine oil dipstick 8. Engine oil filler cap 9. Windshield washer fluid res...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use anyspecial washer fluid such as windshield water repellent type fluid or bugwash. They may cause s...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optim...

3. To attach the new wiper to thewiper arm, align the slot (1) andcross pin (2) and firmly press thewiper arm into the wiper blade untila click is heard. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Ma...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information. Ford pro...

WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near thebattery, always shield your face and protect your eyes. Always provideproper ventilation. WARNING: When lif...

• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. When the battery is disconnected or a new battery installed, thetransmission must relearn its adaptive strategy. As a result of this, thetr...

Note: Electrical or electronic accessories added to the vehicle may adversely affect battery performance and durability and may also affectthe performance of other electrical systems in the vehicle. When a battery replacement is required, the battery should only bereplaced with a Ford recommended re...

If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not u...

• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the enginecoolant. For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when the eng...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine c...

• If available, refer to the chart on the coolant container toensure the coolant concentration in your vehicle will provideadequate protection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water fo...

2. Leave the engine running until the coolant temperature gauge needlemoves away from the H range. After several minutes, if this does nothappen, follow the remaining steps. 3. Turn the engine off and wait for it to cool before checking the coolantlevel. WARNING: Never remove the coolant reservoir c...

When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high-speedoperation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to pre...

• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and wash skin thoroughly with soap and water. Repeated orprolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful i...

Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel conta...

inlet to close properly. If this action corrects the problem, the check fuelfill inlet lamp or CHECK FUEL FILL INLET message may not resetimmediately. It may take several driving cycles for the check fuel fill inletlamp or CHECK FUEL FILL INLET message to turn off. A driving cycleconsists of an engi...

Fuel quality If you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of “Regular” unleadedgasoline. Premium unleaded gasoline is not recommended for vehiclesdesigned to use “Regular” unleaded gasoline because it may cause theseproble...

Refilling with a portable fuel container With the Easy Fuel™ “no cap” fuel system, use the following directionswhen filling from a portable fuel container: WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel™ system. This could damage the fuel syst...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performan...

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick and also in the Maintenance product specifications and capacities section in this chapter. Use of a non-approved automatic transmissi...

Changing the air filter element 1. Release the clamps that securethe air filter housing cover. 2. Carefully separate the two halvesof the air filter housing. 3. Remove the air filter elementfrom the air filter housing. 4. Wipe the air filter housing andcover clean to remove any dirt ordebris and to ...

Cooling system • Protect against freezing temperatures. • When removing vehicle from storage, check coolant fluid level.Confirm there are no cooling system leaks, and fluid is at therecommended level. Battery • Check and recharge as necessary. Keep connections clean. • If storing your vehicle for mo...

• Check fluid levels (including coolant, oil and gas) to make sure thereare no leaks, and fluids are at recommended levels. • If the battery was removed, clean the battery cable ends and inspect. If you have any concerns or issues, contact your authorized dealer. MOTORCRAFT PART NUMBERS Component 3....

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Keyless entry keypad • Vehicle security systems • Vehicle tracking and recovery* • Wheel locks • Windshield wiper shaker* • Remote start • Cargo shade • Cargo area protector • Bumper and hitch mounted parking sensors* • Locking gas plug for capless fuel system *Ford Licensed Accessor...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

Genuine Ford parts and service When planning your maintenance services, consider your dealership forall your vehicle’s needs. There are a lot of reasons why visiting your dealership for all yourservice needs is a great way to help keep your vehicle running great. Convenience Many dealerships have ex...

NORMAL SCHEDULED MAINTENANCE AND LOG For your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service interval. You shouldperform the engine oil change as indicated by the message center. Themessage center will display ENGINE OIL CHANGE SOON or OILCH...

Oil Change S ervice Interval* 1 23456789 1 0 1 1 1 2 1 3 1 4 1 5 Change engine oil and filter • •••••••••••••• Rotate tires, inspect tire wear and measure tread depth • •••••••••••••• Inspect wheels and related components for abnormal noise, wear , looseness or drag • •••••••••••••• Perform multi-po...

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below, you will need to have some items maintainedmore frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additionalmain...

Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery, taxi, patrol car or livery As required – Change engine oil and filter as indicated by messagecenter and perform services listed in the NormalScheduled Maintenance chart (except Fiesta) Inspect f...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently, service as required – Replace cabin air filter (if equipped) – Replace engine air filter Every 5,000 miles (8,000 km) – Inspect the wheels and related components forabnormal noise, wear, looseness or drag– Rotate tires,...

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. Theyare listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic fluid and light duty trucks equipped with Ford-design axlesare lubricated for life. These fluids are not...

ENGINE COOLANT CHANGE RECORD Initial change 6 years or 100,000 miles (160,000 km)(whichever comes first) After initial change Every 3 years or 50,000 miles (80,000 km) Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE...

A Accessory delay ..........................99 Active Park Assist .....................303 Adaptive Cruise Control ...........105 AdvanceTrac ..............................277 Airbag supplemental restraintsystem ........................197, 206, 208 and child safety seats ............199description ...

U Universal garage door opener ..116 V Vehicle Identification Number(VIN) ..........................................415 Vehicle loading ..........................255 Ventilating your vehicle ...........272 W Warning lights (see Lights) .......14 Washer fluid ..............................378 Water, ...