Ford 2011 Escape v.2- User Manual

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

Ford or its vendors to receive this information, do not activatethe service. Ford Motor Company and the vendors it uses toprovide you with this information do not store your vehicle travelinformation. For more information, see Traffic, Directions andInformation, Terms and Conditions. See your SYNC 威...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Base instrument cluster shown in standard measure. Metricsimilar. Optional instrument cluster shown in standard measure. Metricsimilar. Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light m...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on positionwhen the engine is not running, or in a position between on and start, orby applying the parking brake when the ignition is turned to the onp...

Charging system: Illuminates when the battery is not charging properly.If it stays on while the engine isrunning, there may be a malfunctionwith the charging system. Contact your authorized dealer as soon aspossible. This indicates a problem with the electrical system or a relatedcomponent. Engine o...

Speed control: Illuminates when the speed control is engaged. Turnsoff when the speed control systemis disengaged. Overdrive cancel and gradeassist: Illuminates when the overdrive function of thetransmission has been turned offand the grade assist function hasbeen turned on, refer to the Driving cha...

Parking brake on chime: Sounds when the parking brake is left on and the vehicle is driven. If the warning stays on after the park brake is off,contact your authorized dealer as soon as possible. Message center activation chime (if equipped): Sounds when a warning message (except PARKING BRAKE ENGAG...

Optional instrument cluster shown in standard measure. Metricsimilar. Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the ...

Trip odometer: Registers the miles (kilometers) of individual journeys. • Standard instrument cluster: Press the SELECT/RESET controlonce to switch from the odometer tothe TRIP A feature. Press thecontrol again to select the TRIP Bfeature. To reset the trip, press andhold the control again until the...

Your vehicle must be moving to calculate instantaneous fuel economy.When your vehicle is not moving, this function shows ↓ , one or no bars illuminated. Instantaneous fuel economy cannot be reset. Blank Screen The message center display will be blank after cycling through all of theInfo menu items. ...

To reset the oil monitoring system to 100% after each oil change,perform the following: 1. Press and release the SETUP button to display “OIL LIFE XXX%HOLD RESET = NEW”. 2. Press and hold the RESET button for two seconds and release to resetthe oil life to 100%. Note: To change oil life 100% value t...

ZONE [XX] RESET = CHANGE (if equipped) For more information on the compass and compass set up, refer to Electronic compass in the Driver Controls chapter. RESET FOR CALIBRATION (if equipped) For more information on the compass and compass set up, refer to Electronic compass in the Driver Controls ch...

AUDIO SYSTEMS AM/FM single CD/MP3 satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. Your primary respon...

AM/FM Radio / VOL (Power/Volume): Press to turn the radio on/off. Turn theknob to increase/decrease volume. If the volume is set above a certainlevel and the ignition is turned off,the volume will come back on at anominal listening level when theignition is turned back on. AM/FM: Press repeatedly to...

MEMORY PRESETS (0–9): There are 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memorypresets, tune to the desired channelthen press and hold a memorypreset number (0–9) until soundreturns. TEXT: Press and release to display the artist and song title. While in...

an audible prompt. Press OK while SONG ALERT is in the display andthe system will take you to the channel playing the desired song. Youcan save up to 20 song titles. If you attempt to save more than 20titles, the display will read REPLACE SONG? Press OK to access thesaved titles and press / to cycle...

Note: you must be tuned to the specific channel you want tolock/unlock when using this feature. b. CHANGE PIN: Press OK when CHANGE PIN is displayed. The display will read ENTER OLD PIN. Enter your current (old) PINnumber and when the system accepts your entry it will displayENTER NEW PIN. Enter you...

Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers withhigh fidelity. To achieve optimalperfor...

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and also to chargedevices if they support this feature.For further information on thisfeature, refer to Accessing and using your USB port in the SYNC 威 s...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna. You are in a location th...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Turn to select fan speed. 2. R Rear defroster: Press to activate/deactivate the rear window defroster. Refer to Rear window defroster later in this chapter for more information. 3. Defrost: Distributes outside air throu...

9. Temperature control: Controls the temperature of the airflow in the vehicle. 10. Passenger heated seat control (if equipped): Press to activate/deactivate the passenger heated seat. See Heated seats in the Seating and Safety Restraints chapter. 11. Recirculated air: Press to activate/deactivate a...

• Do not put objects under the front seats that will interfere with theairflow to the back seats. • Remove any snow, ice or leaves from the air intake area at the base ofthe windshield. • To improve the time to reach comfort in hot weather, drive with thewindows slightly open for 2-3 minutes after s...

DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED) 1. AUTO/Driver temperature: Press to engage full automatic operation. Select the desired temperature using the temperature control.The system will automatically determine fan speed, airflow distribution,A/C on or off, and outside or recirculated air, ...

14. Driver heated seat control (if equipped): Press to activate/deactivate the driver heated seat. See Heated seats in the Seating and Safety Restraints chapter. Outside temperature: The outside temperature will appear in the display and is labeled EXT TEMP. Temperature conversion: To switch between...

• Manual operation: 1. Select MAX A/C. 2. Select or . 3. Select (recirculated air) to provide colder airflow. 4. Set the temperature to 60°F (16°C). 5. Set highest fan setting initially, then adjust to maintain comfort. To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Rotate back to to turn the headlamps off. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe ...

Autolamp delay system (if equipped) If your vehicle is equipped with autolamps, you can set the delay time tokeep the headlights on for up to three minutes after the key is turnedoff. The delay time is set to 20 seconds at the factory, but the delay timemay be changed by following the steps below (S...

Flash-to-pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the low beam headlamps on with a reduced output. To activate: • the ignition must be in the on position. • the headlamp control must be in the off, parking lamps or autolamppo...

Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmerswitch from the full dim position to the full dome/on position to reset.This will ensure that your displays are visible under all lightingconditions. AIMING TH...

5. Locate the vertical adjuster onthe headlamp, then use a 4 mmsocket to turn the adjuster eithercounterclockwise (to adjust up) orclockwise (to adjust down) aligningthe upper edge of the light patternto the horizontal line. 6. Move the opaque cloth to coverthe right-hand headlamp and repeatSteps 4 ...

Map lamps (without moon roof) The map lamp controls (withoutmoon roof) are located on the domelamp. • Press the button on either side ofeach map lamp to illuminate thelamps. • Press the button again to turn offthe lamps. Map lamps (with moon roof) For models equipped with a moonroof, the map lamps a...

Ambient lighting (if equipped) Illuminates footwells, cupholders,the console bin and the console traywith a choice of several colors. Theambient lighting control switch islocated on the floor console. • To activate, press and release thecontrol to cycle through the colorchoices plus the off state. T...

Take your vehicle to a dealer for service if any of the above conditions ofunacceptable moisture are present. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America and an“E” for Europe to ensure lamp perfo...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Press the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pr...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: 2 — Normal speed operation of rearwiper. 1 — Intermittent operation of rearwiper. O (off) — Rear wiper and washer off. For rear wash cycle, rotate (and hold as de...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamp. Slide-on-rod feature Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage. Note: To stow the visor back into the headliner, visor must beretracted before moving it ...

Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. If the compass still appears to be inaccurate, a manualcalibration may be necessary. Refer to Compass calibration adjustment . Most geographic areas (z...

Compass calibration adjustment Perform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, turn off all electricalaccessories (heater/air conditioning, wipers, etc.) and make sure allvehicle doors are shut. 1. Start the vehicle. 2. To calibr...

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe battery from being discharged: • do not use the power point longer than necessary when the engine isnot running, • do not leave battery chargers, video ...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controls(except for the driver’s) press theright side of the control. Press theleft side to restore the windowcontrols. Accessory delay With accessory delay, the window switches, moon ro...

Do not clean the housing or glass of any mirror with harshabrasives, fuel or other petroleum-based cleaning products. Note: If equipped with a rearview camera system, a video image will display in the mirror or the navigation system display (if equipped) whenthe vehicle is put in R (Reverse). As you...

Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a scraper orattempt to readjust the mirrorglass if it is frozen in place.These actions could cause damage to the glass...

Turning off speed control To turn off the speed control, press OFF or turn off the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some audio control features...

SYNC 威 system hands-free control feature (if equipped) Press briefly to use the voice command feature. You will hear atone and LISTENING will appear inthe radio display. Press andhold to exit voice command. Press to activate phone mode or answer a phone call. Press andhold to end a call or exit phon...

The moon roof has a sliding shade that can be opened or closed whenthe glass panel is shut. To close the shade, pull it toward the front of thevehicle. Accessory delay: With accessory delay, the window switches, audio system, and moon roof(if equipped) may be used for up to 10 minutes after the igni...

POSITIVE RETENTION FLOOR MAT WARNING: Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that theeyelet is over the retention post andpress down to lock in. Make surethat the mat do...

WARNING: Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. Exhaust fumes contain carbon monoxide which can injure yourlungs and cause drowsiness and even death. This will also preventpassengers and cargo from falling out. If you mus...

The larger, rearward, compartmentis for customer storage. To open, liftthe lid with the pull latch. The lidcan be removed to allow for flexiblestorage. To close, lower the lid andpress down at the latch area untilyou hear the latch engage. A padlock or combination lock can beapplied to use the locka...

3. Use a long, flat object to depressthe tongue in the endcaps on bothsides of the cross-bar. 4. Slide the cross-bar assembly offthe end of the rail. Be sure to check that the thumbwheels are tight each time load isadded, or removed from the roof rack, and periodically while traveling.Always ensure ...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unlocks/locks all thedoors. The transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non-progr...

MYKEY™ The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehicle can be activated as a MyKey™. The key will remain restricteduntil MyKey™ is cleared. Any remaining keys are referred to as an“administrator key” o...

2. Press and release the RESET button. HOLD RESET TO CONFIRMMYKEY will be displayed. 3. Press and hold the RESET button for two seconds until MARK THISAS RESTRICTED is displayed. 4. Wait until KEY RESTRICTED AT NEXT START is displayed. MyKey™ is successfully programmed. Make sure you label it so you...

Clear MyKey™ To reset all MyKeys™ as admin keys do the following: 1. Turn the vehicle on using the admin key. 2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 3. Press and release the RESET button. HOLD RESET TO CONFIRMCLEAR is displayed. 4. Press and hold the RESET button for two secon...

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED or ADMIN KEYS PROGRAMMED that is displayed in the MyKey™ SystemStatus menus will include the remote start system as an additional key inthe total count. See the Check MyKey™ System Status section. Note: For all vehicles with remote start inst...

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Door key unlocking/locking Unlocking the doors Turn the key in the door cylinder to unlock the driver’s door only. Allother doors will remain locked. Locking the doors Turn the key in the door cylinder t...

Message center procedure (if equipped) For information on activating/deactivating the autolock feature using thevehicle’s message center, refer to Message center information in the Instrument cluster chapter. Autounlock The autounlock feature will unlock all the doors when: • the ignition is in the ...

1. Place the key in the ignition andturn the ignition to the on position. 2. Press the power door unlockcontrol on the door panel threetimes. 3. Turn the ignition from the onposition to the off position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back ...

CHILDPROOF DOOR LOCKS When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thechildproof door locks are set, butthe doors are unlocked. The childproof locks are located onthe rear edge of each rear door andmust be set separately f...

The IKT allows you to: • remotely unlock the vehicledoors. • remotely lock all the vehicledoors. • remotely open the power liftgateglass. • activate the personal alarm. • operate the illuminated entryfeature. The remote entry lock/unlockfeature operates in any ignitionposition except while the key i...

To replace the battery: 1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover. Note: Do not wipe off any grease on the battery terminals on the backsurface of the circuit board. 2. Remove the old battery. Note: Please refer to local regulations when disposi...

• pressing the control on the remote entry transmitter, • or the ignition position changes. Unlocking and locking the doors and liftgate using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of eacho...

Note: Do not leave a duplicate coded key in the vehicle. Alwaystake your keys and lock all doors when leaving the vehicle. Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is in the offposition, the indicator will flashonce every two secon...

key that operates all the locks and starts the vehicle, as well as a remotekeyless entry transmitter. A maximum of eight coded keys can beprogrammed to your vehicle; only four of these eight keys can be IKTswith remote entry functionality. If your IKTs or standard SecuriLock 威 coded keys are lost or...

REAR SEATS Second row adjustable head restraints Your vehicle is equipped with second row outboard and center headrestraints that are vertically adjustable. WARNING: To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the v...

2. Press and hold the adjust/removebutton, then pull up on the headrestraint. To reinstall the adjustable head restraint, do the following: 1. Insert the two stems into theguide sleeve collars. 2. Push the head restraint downuntil it locks. Properly adjust the head restraint so that the top of the h...

2. Pull the seat release strap. Note: Make sure the floor is clear of all objects before folding the seat. 3. Flip seat forward. Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught bystaying out of the seat back foldingpath...

To install the second row cushion 1. Push the cushion to the inboardside of the vehicle. 2. Make sure that the hinges arelocked into place. SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and i...

Front passenger sensing system For airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants that are very closeto the airbag when it begins to inflate. For some occupants, like infantsin rear-facing child seats, this occurs because the...

Safety restraints precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap wh...

WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a childanywhere near them. Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckl...

When to use the automatic locking mode This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children12 years old and under should be properly restrained in a rear seatingposition whenever possible. Refer to Safety restrai...

numbers 611C22–A and 611C22–B respectively). These assemblies canbe obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label. Also, use the safety belt extension only if t...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day. The more we drive, the more we areexposed to ⬙ rare ⬙ events, even for good drivers. 1 in 4 of us will b...

Reasons given... Consider... ⬙ The people I’m with don’t wear belts ⬙ Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children andyounger brothers/sisters imitatebehavior they see. ⬙ I have an airbag ⬙ Airbags offer greater protection whenused with safety bel...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The RCM (restraints control module) monitors its own internal circuitsand the supplemental airbag electrical system wiring (including theimpact sensors, the system wiring, the airbag system readiness light, theairbag backup power and the airbag ignitors). WARNING: Several air bag system components g...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

A difficulty with the system is indicated by one or more of the following: • The readiness light will eitherflash or stay lit. • The readiness light will notilluminate immediately afterignition is turned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the p...

How does the side airbag system work? The design and development of theside airbag system includedrecommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk ofinjuri...

WARNING: Several airbag system components get hot after inflation. Do not touch them after inflation. WARNING: If the side airbag has deployed, the airbag will not function again.The side airbag system(including the seat) must beinspected and serviced by anauthorized dealer. If the airbag is not rep...

How does the Safety Canopy 姞 System work? The design and development of theSafety Canopy system includedrecommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk of...

A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will eitherflash or stay lit. • The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pa...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) or less(generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier,convertible seat,or toddler seat). Smallc...

• When possible, always properly restrain children twelve (12) years ofage and under in a rear seating position of your vehicle. Accidentstatistics suggest that children are safer when properly restrained inthe rear seating positions than in a front seating position. Recommendations for attaching ch...

WARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’s size,height, weight, or age. Follow the child restraint manufacturer’sinstructions and warnings provided for install...

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertified Child Passenger Safety Technician (CPST) and yourpediatrician to make sure your seat is appropriate for your child andproperly installed in the veh...

Perform the following steps when installing the child seat withcombination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in aseat with a combination lap a...

8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up on the shoulder belt inorder to force slack from the belt.This is necessary to remove theremaining slack that will exist oncethe additional weight of...

Use of inboard lower anchors from the outboard seating positions(center seating use) The lower anchors at the center of the second row rear seat are spaced400 mm (16 inches) apart. The standardized spacing for LATCH loweranchors is 280 mm (11 inches) center to center. A child seat with rigidLATCH at...

The rear seating positions of your vehicle are equipped with built-intether strap anchors located behind the seats on the roof panel in thecargo area. The tether strap anchors in yourvehicle are in the following positions(shown from top view): Attach the tether strap only to the appropriate tether a...

2. Locate the correct anchor for theselected seating position. There are three tether anchorslocated on the headliner at the rearof the vehicle. 3. Clip the tether strap to theanchor as shown. The arrow in the above graphicpoints toward the front of thevehicle. If the tether strap is clippedincorrec...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

For 4WD vehicles, a spare tire of a different size other than the tireprovided should never be used. A dissimilar spare tire size (other thanthe spare tire provided) or major dissimilar tire sized between the frontand rear axles could cause the 4WD system to stop functioning anddefault to front-whee...

Treadwear The treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernment test course. For example, a tire graded 150 would wear oneand one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The ...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

WARNING: Age Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed,inflation pressure, etc.) the tires experience throughout their lives.In general, tires should be replaced after six years regardless of treadwear. However, heat cau...

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed to be used in aftermarket wheels.The use of wheels or tires not recommended by Ford Motor Companymay affe...

vehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel alignmentperiodically. Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by an authorized dealer.Fro...

5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in yourowner...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your tire pressure monitoring system (TPMS) The tire pressure monitoring system measures pressure in your four roadtires and sends the tire pressure readings to your vehicle. The low tirepressure warning light will turn on if the tire pressure is significantly low.Once the light is ill...

Low tire pressurewarning light Possible cause Customer action required Solid warning light Tire(s)under-inflated 1. Check your tire pressure toensure tires are properlyinflated; refer to Inflating your tires in this chapter. 2. After inflating your tires tothe manufacturer’srecommended inflationpres...

Low tire pressurewarning light Possible cause Customer action required Flashing warninglight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

tire is under-inflated, carefully drive the vehicle to the nearest locationwhere air can be added to the tires. Inflate all the tires to therecommended inflation pressure. SNOW TIRES AND CABLES WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. ...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lb.” on your vehicle’s plac...

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enoughcargo capacity to carry that much weight. In metric units, thecalculation would be: 635 kg - (2 x 9...

Powertrain Maximum GCWR - lb (kg) 1 Maximum Trailer Weight - lb (kg) 2 2WD 2.5L w/manualtransmission 5000 (2268) 1500 (680) 2WD 2.5L w/automatictransmission 5060 (2295) 1500 (680) 4WD 2.5L 5200 (2359) 1500 (680) 2WD 3.0L 7140 (3239) 3500 (1588) 4WD 3.0L 7300 (3311) 3500 (1588) 1 For high altitude op...

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

• Allow more distance for stopping with a trailer attached; anticipatestops and brake gradually. Trailer towing tips • Practice turning, stopping and backing-up before starting on a trip toget the feel of the vehicle-trailer combination. When turning, makewider turns so the trailer wheels will clear...

In case of roadside emergency with a disabled vehicle, please refer to Wrecker towing in the Roadside Emergencies chapter. These guidelines are designed to prevent damage to your vehicle after itis hooked-up to the RV or tow dolly. Front-wheel drive (FWD) vehicles can be towed with all four wheels o...

STARTING Positions of the ignition 1. Off— locks the gearshift leverand allows key removal. Note: In order to switch off the engine whilethe vehicle is in motion, shift toneutral and use the brakes to bringthe vehicle to a safe stop. After thevehicle has stopped, turn the engineoff and shift into pa...

Do not crank the engine for more than 10 seconds at a time as starterdamage may occur. If the engine fails to start, turn the key to off andwait 30 seconds before trying again. Do not use starting fluid such as ether in the air intake system. Suchfluid could cause immediate explosive damage to the e...

• Be sure that the engine block heater, heater cord and extension cordare solidly connected. A poor connection can cause the cord tobecome very hot and may result in an electrical shock or fire. Be sureto check for heat anywhere in the electrical hookup once the systemhas been operating for approxim...

Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an anti-lock braking system (ABS). Thissystem helps you maintain steering control during emergency stops bykeeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking ...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released....

When AdvanceTrac 威 with RSC 威 performs a normal system self-check, some drivers may notice a slight movement of the brake, and/or arumble, grunting, or grinding noise after startup and when driving off. When an event occurs that activates AdvanceTrac 威 with RSC 威 , you may experience the following: ...

or avoiding objects in the roadway. ESC operates by applying brakes toone or more of the wheels individually and, if necessary, reducing enginepower if the system detects that the vehicle is about to skid or slidelaterally. During electronic stability control events, the stability control light in t...

WARNING: Trailer sway control does not prevent a trailer from swaying, it mitigates the sway from increasing once it has occurred. TSC cannot stop all trailers from swaying. If you areexperiencing trailer sway, it is likely that the trailer is improperlyloaded for the correct tongue weight or the sp...

WARNING: Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Do not overload your vehicle and use extra precautions, such as driving at slowerspeeds, avoiding abrupt steering changes and allowing for increasedstopping distance, when driving a heavily load...

N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position. D (Drive) with Overdrive The normal driving position for the best fuel economy. Transmissionoperates in gears one through six. D (Drive) with Grade As...

O/D (overdrive mode) is automatically returned each time the engine isturned off. L (Low) • Provides maximum engine braking. • Will downshift to the lowest available gear for the current vehiclespeed; allows for first gear when vehicle reaches slower speeds. If your vehicle gets stuck in mud or snow...

Do not drive with your foot resting on the clutch pedal or use theclutch pedal to hold your vehicle at a standstill while waiting on ahill. These actions will severely reduce the life of the clutch andcould nullify a clutch warranty claim. Recommended shift speeds Upshift according to the following ...

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system locatedon the liftgate provides a videoimage, which appears in therearview mirror or on the navigationscreen (if equipped), of the areabehind the vehicle. It addsassistance to the driver whilereversing or reverse parking thevehicle. To ...

Note: The default setting for the camera delay is off. Press the “Settings” button found on the navigation screen (if equipped) to set thecamera delay feature to on or off. When towing, the camera will only see what is being towed behind thevehicle; this might not provide adequate coverage as it usu...

Servicing • If the image comes on while the vehicle is not in R (Reverse), havethe camera inspected by your authorized dealer. • If the image is not clear, then check if there is anything covering thelens such as dirt, mud, ice, snow, etc. If the image is still not clearafter cleaning, have your cam...

For best performance, the driver should drive the vehicle as parallel aspossible while passing a parking space. If driven too fast (above 18 mph[30 km/h]) for the system to measure parking spaces, the message centerwill display ACTIVE PARK REDUCE SPEED. When the system has found a space, the message...

When you determine the vehicle is back far enough or you hear a solidtone from the reverse sensing system, bring the vehicle to a completestop and move the gearshift to D (Drive). The message center will nowdisplay PULL FORWARD USE CAUTION followed by a chime. When you determine the vehicle is far e...

Why doesn’t APA position the vehicle where I want in the space? • The driver allows the vehicle to roll in the opposite direction of thetransmission (such as rolling forward when R (Reverse) gear isselected. • You may be driving in R (Reverse). APA can only look for a parkingspace while moving forwa...

Driving with blind spot mirrors Before a lane change, check themain mirror first, then check theblind spot mirror. If no vehicles arepresent in the blind spot mirror andthe traffic in the adjacent lane is ata safe distance, signal that you aregoing to change lanes. Glance overyour shoulder to verify...

Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating characteristics that are somewhatdifferent from conventional vehicles, both on and off the road. How your vehicle differs from other vehicles Truck ...

sideways out of control or roll over. Remember, your safety and thesafety of others should be your primary concern. WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel ...

Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,turn the steering wheel only as rapidly and as far as required to avoidthe emergency. Excessive steering will result in less vehicle control,not more...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, thevehicle may stall. Once throu...

Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand adversely affect driver and passenger safety. Frequent inspection ofvehicle chassis components is recommended if the vehicle is subjected toheavy off-...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours, seven days a week • for the...

Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in the glove compartment. In Canada, the card isfound in the Warranty Guide in the glove compartment. U....

This switch is located in the frontpassenger’s footwell, behind aflip-up cover, by the kick panelaccess cover. To reset the switch: 1. Turn the ignition to the offposition. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 41 15A Driver/passenger door lockswitches, Automatic dimmingmirror, Compass, Ambientlighting, Moon roof, Cameradisplay in mirror 42 10A Not used (spare) 43 10A Rear wiper logic, Heated seatsrelay, Instrument cluster 44 10A Not used (spare) 45 5A...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 31F — Liftgate latch relay 32 — Not used 33 — PCM diode 34 — Start diode 35 10A* Run/start, Reverse lamps, Reardefrost relay 36 — Not used * Mini fuse ** Cartridge fuse CHANGING THE TIRES If you get a flat tire while driving, do not apply the br...

3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the d...

Stopping and securing the vehicle 1. Park on a level surface, set theparking brake and activate hazardflashers. 2. Place gearshift lever in P (Park)(automatic transmission) or R(Reverse) (manual transmission)and turn engine off. Removing the jack and tools 1. The jack and tools are locatedunder the ...

5. Remove the lug wrench from thejack in order to remove the sparetire from under the vehicle. Removing the spare tire or spare tire and tether (if equipped) 1. Insert the lug wrench through theaccess hole in the rear bumper. 2. Turn the handle counterclockwiseand lower the spare tire until it canbe...

5. Use the lug wrench to remove thelug nut from the spare tire tether. 6. If not replacing the spare or flattire to the underbody storage area,raise winch up into the installedposition. 7. Use the attached fastener strap(2) to tie the tether end to thewinch actuator shaft (if equipped). Tire change ...

1. Place tire on end with valve stemfacing rearward, away from vehicle. 2. Place tether into bolt holes inwheel and attach lug nut using lugwrench. 3. Lay the tire on the ground with the valve stem facing down. If yourvehicle is equipped with aluminum wheels, remove the wheel ornament. 4. Slide the ...

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km)after any wheel disturbance (tire rotation, changing a flat tire, wheelremoval, etc.). Bolt size Wheel lug nut torque* ft-lb N • m M12 x 1.5 100 135 * Torque specifications are for nut and bolt th...

5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumpercable to the pos...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the FordMotor Company Customer Relationship Center at 1-800-392-3673. Note: F...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your authorized dealer...

• Spray Motorcraft 威 Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, useMotorcraft 威 Engine Shampoo (CXC-66-A). • Cover the highlighted areas to prevent water damage when cleaningthe engine. • Never wash or rinse the engine while it is hot...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Tar Remover (ZC-42). WINDOWS ...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth, then use a clean and dry white cottoncloth to dry these areas. • Avoid cleaners or polishes that increase the gloss of the upper portionof the instr...

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleather conditioners. These products may cause premature wearing ordamage to the leather. LEATHER SEATS FOR THE KING RANCH 姞 EDITION ONLY (IF EQUIPPED) Your...

• Clean the surfaces using the steps outlined in the Cleaning section. • Ensure the leather is dry then apply a nickel-sized amount ofconditioner to a clean, dry cloth. • Rub the conditioner into leather until it disappears. Allow theconditioner to dry and repeat the process for the entire interior....

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. At the front of the vehicle, lift upon the auxiliary latch handle locatedin the center between the hood andthe grille. 3. Lift the hood open and secure itwith the prop rod. IDENTIF...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use anyspecial washer fluid such as windshield water repellent type fluid or bugwash. They may cause s...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optim...

Changing rear window wiper blade The rear wiper arm is designed without a service position. This reducesthe risk of damage to the blade in an automatic car wash. To replace the wiper blade: 1. Grab the wiper arm with onehand close to the arm/blade jointand pull it as far away from theglass as possib...

5. Locate and carefully remove the engine oil level dipstick. • 2.5L I4 engine • 3.0L V6 engine 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within the lower and upper holes or lower and upperlines, the oil level is acceptable. DO NOT ADD OIL. • ...

• 3.0L V6 engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above the upperhole or upper line may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorize...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils certified for gasoline engines by the American PetroleumInstitute (API). An oil with this trademark symbol conforms to thecurrent engine and emission system protection standards and fue...

BATTERY Your vehicle is equipped with aMotorcraft 威 maintenance-free battery which normally does notrequire additional water during itslife of service. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, k...

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect againstpossible splashing of acid solution. In case of acid contact with skin oreyes, flush immediately with water f...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANTChecking engine coolant The concentration and level of engine coolant shou...

• Refer to scheduled maintenance information for service interval schedules. If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or empty, add engine coolant to the reservoir. Refer to Adding engine coola...

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion...

Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quar...

If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentrationabove 40%. • NEVER decrease the coolant concentration below 40%. • A coolant concentration of 40% will provide freeze pointprotection down to -12°F [-24°C]. Decreased engine coolantconcentrations bel...

When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high-speedoperation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to pre...

WARNING: The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read a...

3. Slowly insert the fuel filler nozzle fully into the fuel system, and leavethe nozzle fully inserted until you are done pumping. Pump fuel asnormal. 4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler no...

If your vehicle is not a flexible fuel vehicle (FFV), then only useUNLEADED fuel or UNLEADED fuel blended with a maximum of 10%ethanol. Do not use fuel ethanol (E85), diesel, methanol, leaded fuel orany other fuel. The use of leaded fuel is prohibited by law and could damage yourvehicle. Your vehicl...

Fuel quality Unleaded gasoline engines If you experience starting, rough idle or hesitation driveability problemsduring a cold start, try a different brand of “Regular” unleaded gasoline.“Premium” unleaded gasoline is not recommended for vehicles designedto use “Regular” unleaded gasoline because it...

2. Slowly insert the funnel into theEasy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container. 4. When done, clean the funnel or properly dispose of it. Extra funnelscan be purchased from your authorized dealer if you choose to disposeof the funnel. Do not use aftermarket fun...

vehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the empty reserve still present in the tank. For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior t...

• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski racks) may reducefuel economy. • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first8–10 miles (12–16 km) of driv...

Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above driving cycle. Theengine must warm up to its normal operating temperature. Once started,do not turn off the engine until the above driving cycle is complete. Ifthe vehicle is s...

Checking and adding manual transmission fluid (if equipped) 1. Park the vehicle on a levelsurface. 2. Engage the parking brake fully –put in first gear. 3. Ensure the vehicle cannot move. 4. Clean the filler plug. 5. Remove the filler plug, located onthe lower, forward driver side of thetransmission...

Changing the air filter element 1. Release the clamps that secure the air filter housing cover. • 2.5L I4 engine • 3.0L V6 engine 2. Pull the air filter housing cover away. 3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to remove any dirt...

VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time(30 days or more), refer to the following maintenance recommendationsto ensure your vehicle stays in good operating condition. All motor vehicles and their components were engineered and tested forreliable, regular dri...

Note: During extended periods of vehicle storage (30 days or more), fuel may deteriorate due to oxidation. Add Motorcraft 威 Gas Stabilizer or equivalent meeting Ford material specification ESE-M99C112-A to thevehicle fuel system whenever actual or expected storage periods exceed30 days. Follow the i...

• Check the exhaust for any foreign material that may have collectedduring storage. • Check tire pressures and set tire inflation per the Tire Label. • Check brake pedal operation. Drive the vehicle 15 ft (4.5 meters) backand forth to remove rust build up. • Check fluid levels (including coolant, oi...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location 3. Make, vehicle line, series, bodytype 4. Engine type 5. Check digit 6. Model year 7. Assembly plant ...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Keyless entry keypad • Protective seat covers* • Remote start system • Windshield wiper shaker* • Vehicle security system • Back up camera* • Wheel locks • Back up alarm* • Vehicle tracking and recovery* • Locking gas plug for capless fuel system • Bumper and hitch mounted parking se...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

different specifications and performance features. That’s why it’simportant to rely upon your dealership to properly diagnose and repairyour vehicle. Ford Motor Company has recommended maintenance intervals forvarious parts and component systems based upon engineering testing.Ford Motor Company reli...

Convenience Many dealerships have extended evening and Saturday hours to makeyour service visit more convenient. How’s that for quality service? Factory-trained technicians Service technicians participate in extensive factory-sponsoredcertification training to help them become experts on the operati...

Multi-point inspection - Recommended at every visit Accessory drive belt(s) Operation of horn, exterior lampsand hazard warning system Battery performance Radiator, coolers, heater and airconditioning hoses Clutch operation (if equipped) Shocks, struts and othersuspension components for leaksand dam...

NORMAL SCHEDULED MAINTENANCE AND LOG For your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service interval. You shouldperform the engine oil change as indicated by the message center. Themessage center will display ENGINE OIL CHANGE SOON or OILCH...

Oil Change S ervice Interval* 1 23456789 1 0 1 1 1 2 1 3 1 4 1 5 Change engine oil and filter • •••••••••••••• Rotate tires, inspect tire wear and measure tread depth • •••••••••••••• Inspect wheels and related components for abnormal noise, wear , looseness or drag • •••••••••••••• Inspect front ax...

Every 150,000 miles(240,000 km) Change automatic transmission fluid and filter(except 5–speed TorqShift 威 transmission) (filter not required on 6F35, 6F50, DPS6 and AWF-21transmissions); consult dealer for requirements Change front axle fluid (4WD vehicles) Change manual transmission fluid (Escape) ...

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below, you will need to have some items maintainedmore frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additionalmain...

Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery, taxi, patrol car or livery As required – Change engine oil and filter as indicated by messagecenter and perform services listed in the NormalScheduled Maintenance chart Inspect frequently, servi...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently, service as required – Replace cabin air filter (if equipped) – Replace engine air filter Every 5,000 miles (8,000 km) or 6 months – Change engine oil and filter – Inspect wheels and related components for abnormalnoise,...

Off-road operation Inspect frequently, service as required – Inspect steering linkage, ball joints and U-joints;lubricate if equipped with grease fittings– Replace cabin air filter (if equipped)– Replace engine air filter Every 5,000 miles (8,000 km) or 6 months – Change engine oil and filter – Insp...

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. Theyare listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic fluid and light duty trucks equipped with Ford-design axlesare lubricated for life. These fluids are not...

ENGINE COOLANT CHANGE RECORD Initial change 6 years or 100,000 miles (160,000 km)(whichever comes first) After initial change Every 3 years or 50,000 miles (80,000 km) Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE...

A Accessory delay ..........................73 Active Park Assist .....................231 AdvanceTrac ..............................214 Airbag supplemental restraintsystem ........................137, 146, 149 and child safety seats ............139description ..............137, 146, 149disposal ......

N Navigation system .......................46 O Octane rating ............................307 Oil (see Engine oil) ..................291 Overdrive ...................................222 P Parental MyKey programming ...92 Park Assist ................................231 Parking brake ....................

V Vehicle Identification Number(VIN) ..........................................329 Vehicle loading ..........................192 Ventilating your vehicle ...........209 W Warning lights (see Lights) .......12 Washer fluid ..............................289 Water, Driving through .............243 Wind...