Ford 2010 Taurus v.3- User Manual

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may takeyour focus off the road. Your primary responsibility is the safeoperation of your vehicle.We recommend aga...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Standard instrument cluster shown, optional cluster similar Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many...

Solid illumination after the engine is started indicates the On BoardDiagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic co...

Low washer fluid (RTT): Illuminates when the washer level inthe washer fluid reservoir is low. Door ajar (RTT): Illuminates in the message center display whenthe ignition is in the run positionand any door is open. Trunk ajar (RTT): Illuminates in the message center display whenthe ignition is in th...

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the off or accessory position and the driver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedriver’s door is ope...

MESSAGE CENTER Your vehicle’s message center allows you to configure/personalize certainvehicle options to suit your needs. The message center is also capable of monitoring many vehicle systemsand will alert you to potential vehicle problems and various conditionswith an informational message follow...

If you calculate your average fuel economy by dividing distance traveledby gallons of fuel used (liters of fuel used by 100 kilometers traveled),your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic...

System check and vehicle feature customization Press the SETUP button repeatedlyto cycle the message center throughthe following features: RESET FOR SYSTEM CHECK When this message appears, press RESET and the message center willbegin to cycle through the following systems and provide a status of the...

3. Once “OIL LIFE SET TO XXX%” is displayed, release and press theRESET button to change the Oil Life Start Value. Each release and presswill reduce the value by 10%. Note: Oil life start value of 100% equals 7,500 miles (12,000 km) or 12 months. For example, setting oil life start value to 60% sets...

Press RESET to turn the warning chime on or off. The system will revertto chime on each time the vehicle is started. The heads up display and/orchime will activate briefly to confirm the last setting. COLLISION WARN SYSTEM (if equipped) This feature warns the driver of a possible collision. See Coll...

LANGUAGE = ENGLISH / SPANISH / FRENCH Allows you to choose which language the message center will display in.Selectable languages are English, Spanish, or French. Waiting four seconds or pressing the RESET button cycles the messagecenter through each of the language choices. Press and hold RESET for...

SERVICE ADVANCETRAC — Displayed when the AdvanceTrac 威 system has detected a condition that requires service. TO STOP ALARM START VEHICLE — Displayed when the perimeter alarm system is armed and the vehicle is entered using the key on thedriver’s side door. In order to prevent the perimeter alarm sy...

AUDIO SYSTEMS Note: If your volume is muted and MYKEY VOLUME LIMITED is displayed, refer to MyKey™ in the Locks and Security chapter for more information. AM/FM CD/MP3 satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford...

Setting the clock To set the time, press CLOCK. Thedisplay will read SET TIME. Use thememory preset numbers (0–9) toenter in the desired time–hours and minutes. The clock will then beginfrom that time. AM/FM Radio / VOL (Power/Volume): Press to turn the radio on/off. Turn theknob to increase/decreas...

CD/MP3 Player CD: Press to enter CD/MP3 mode. If a disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded, NO DISC will appear in thedisplay. LOAD:For a single CD system– This control is not operational. To load aCD, simply insert the disc, label side up...

MEMORY PRESETS (0–9): There are 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memory presets, tune to the desired channelthen press and hold a memory preset number (0–9) until sound returns. TEXT: Press and release to display the artist and song title. While...

• CHANNEL LOCKOUT MENU- Press OK to enter the Channel Lockout menu. Press the SEEK to scroll through the following options: a. LOCK/UNLOCK THIS CHANNEL: Press OK when LOCK/UNLOCK THIS CHANNEL is displayed and the display will readENTER PIN. Enter your four-digit PIN number (initial PIN is 1234)and t...

Your vehicle is equipped with anauxiliary input jack (AIJ). Theauxiliary input jack provides a wayto connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers withhigh fidelity. To achieve optimalperfor...

Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also to charge devices ifthey support this feature. Forfurther information on this feature,refer to Accessing and using your USB port in the SYNC 威 supple...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna. You are in a location th...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear th...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. + Fan speed control: Press to increase the fan speed. 2. Defrost: Distributes outside air through the windshield defros...

Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. CLIMATE: Press to control the climate control system through the touch display screen. See Touchscreen functions later in this section. 2. R Rear defroster: Press to activa...

• : Distributes air through the floor vents, rear seat floor vents. • : Distributes air through the windshield defroster vents, de-mister vents, floor vents and rear seat floor vents. The system willautomatically provide outside air to reduce window fogging. To return to full automatic control, pres...

For maximum cooling performance: • Automatic operation: 1. Press AUTO for full automatic operation. 2. Do not override A/C or (recirculated air). 3. Set the temperature to 60°F (16°C). • Manual operation: 1. Select MAX A/C. 2. Select (panel) or (panel/floor). 3. Select (recirculated air) to provide ...

CABIN AIR FILTER The cabin air filter element is designed to reduce the concentration ofairborne particles such as dust, spores and pollen in the air beingsupplied to the interior of the vehicle. The presence of a particulate filterelement provides the following benefits: • Improves your driving com...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled b...

4. Turn the headlamp control to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamps off. High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivat...

Scenario 3: Conditions - The automatic high beam system is set to ON in the message center. The headlamp switch is in (off), (park lamps), or (on). Operation - The high beam switch can be used to turn the high beams on and off. Scenario 4: Conditions - The automatic high beam system is set to OFF in...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicablelit components in the vehicle duringheadlamp and parking lampoperation. • Tap the top or bottom of thecontrol to brighten/dim all interiorlit components incrementally, or • Press and hold at the first position...

Ambient lighting (if equipped) Illuminates footwells and cupholderswith a choice of several colors. Theambient lighting control is located inthe center console storage area. Toactivate, press and release the leftside of the control to cycle throughthe color choices plus the off state.Press the right...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Rain sensing wipers (ifequipped): The rain sensing wipers will automatically activate whenmoisture is present on thewindshield ...

Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick push and hold: the wiperswill swipe three times withwasher fluid. • a long push and hold: the wipersand washer fluid will be activatedfor up to ten seconds. Courtesy wipe featu...

TILT/TELESCOPE STEERING WHEEL To adjust the steering wheel: 1. Pull the lever down to unlock thesteering column. 2. While the lever is in the downposition, move the steering wheelup or down and in or out until youfind the desired position. 3. While holding the steering wheelin place, pull the lever ...

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment The storage compartment may beused to store a pair of sunglasses.Press the release area on the rearedge of the bin door to open thestorage compartment. The door willopen ...

2. To calibrate, press and hold the 7and 9 radio preset buttons togetherfor approximately 10 seconds untilCAL appears. Release the buttons. 3. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CAL display changes to thedirection value (N, S, E, W, etc.). Itmay take up to five c...

• do not leave battery chargers, video game adapters, computers andother devices plugged in overnight or when the vehicle is parked forextended periods. Always keep the power point caps closed when not being used. POWER WINDOWS WARNING: Do not leave children unattended in the vehicle and do not let ...

Bounce-Back (one-touch up or down windows only) When an obstacle has been detected in the window opening as thewindow is moving upward, the window will automatically reversedirection and move down. This is known as “bounce-back”. If the ignitionis turned off (without accessory delay being active) du...

POWER REAR SUNSHADE (IF EQUIPPED) Your vehicle may be equipped with apower rear sunshade that covers therear window of your vehicle. Thecontrol is located in the centerconsole access bin next to thepower point. Press the control to move the shadeup or down. The power sunshade is equippedwith an auto...

Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press a...

Using speed control The speed controls are located on the steering wheel. The followingbuttons work with speed control: RESUME: Press to resume a set speed. SET +: Press to increase the set speed. SET – : Press to decrease the set speed. OFF/ON: Press to turn speed control off or on. Setting speed c...

WARNING: Always pay close attention to changing road conditions, especially when using Adaptive Cruise Control. Adaptive Cruise Control cannot replace attentive driving. Failing tofollow any of the warnings below or failing to pay attention to the roadmay result in a collision, serious injury or dea...

3. Press and release the SET +control. The vehicle speed will bestored in the memory and themessage center will display SETXXX MPH (your desired speed). 4. Take your foot off the acceleratorpedal. 5. The green cruise indicator light on the instrument cluster willilluminate if there are no vehiclesde...

Cause Action The surface of the radar in thegrille is dirty or obstructed insome way Clean the grille surface in front ofthe radar or remove the objectcausing the obstruction The surface of the radar in thegrille is clean but the messageremains in the display Wait a short time. It may takeseveral mi...

STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features VOL + (Volume): Press to increase the volume. VOL – (Volume): Press to decrease the volume. (Seek): Press to select the previous/next radiostation preset, CD track or satelliteradio channel preset depending onwhich media mode you are in. M...

SYNC 威 system hands-free control feature (if equipped) Press briefly to use the voice command feature. You will hear atone and LISTENING will appear inthe radio display. Press andhold to exit voice command. Press to activate phone mode or answer a phone call. Press andhold to end a call or exit phon...

To open the moon roof: Press and release the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof. WARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the mo...

Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink 威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, theprogrammed Homelink 威 buttons be erased for security purposes, refer to Programming in thi...

5. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 6. 6. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button. Repeat the pres...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

To erase programming on the Car2U 威 system (individual buttons cannot be erased), use the following procedure: 1. Firmly press the two outsideCar2U 威 system buttons simultaneously for approximately20 seconds until the indicator lightsbegin to blink rapidly. The indicatorlights are located directly a...

INTERIOR TRUNK CONTROL The trunk release button is locatedon the instrument panel near theradio. Press the button to open thetrunk. CARGO AREA FEATURES Cargo net (if equipped) The cargo net secures lightweightobjects in the cargo area. Attach thenet to the anchors provided. Do notput more than 50 lb...

KEYS Integrated keyhead transmitters (IKTs) (If equipped) Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade starts thevehicle and unlocks/locks all thedoors. The transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to yourvehic...

MYKEY™ The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehicle can be activated as a MyKey™. The key will remain restricteduntil MyKey™ is disabled. Any remaining keys are referred to as an“administrator key” ...

Create a MyKey™ To program MyKey™ on one of the keys programmed to the vehicle,insert the key that you want to make a MyKey™ into the ignition. Forvehicles equipped with push button start, put the intelligent access keyin the backup slot; see the Driving chapter for the location of the backup slot. ...

5. Press SETUP to enter your choice. The next optional setting will bedisplayed. 6. Repeat Steps 4 and 5 until you are done changing the optionalsettings. Disable MyKey™ To reset all MyKeys™ as admin keys, do the following: 1. Turn the vehicle on using the admin key. 2. Press SETUP until PRESS RESET...

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Smart unlocks This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open one of the front doors and you lock the vehicle with thepower d...

automatically be released when you attempt to close it, and the horn willchirp, as a reminder that the IA key is inside. If you would like tointentionally lock your IA key in the trunk of your vehicle, first disarmthe perimeter alarm by unlocking the vehicle, then place the IA key inthe trunk, close...

Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition off. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user will receive a horn chirp to ind...

Keyless entry keypad autounlock enable/disable procedure 1. Turn the ignition off. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8 a second ti...

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the oper...

WARNING: Do not leave children, unreliable adults, or animals unattended in the vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people oranimals to these high temperatures for even a short time can causedeath or serious heat-related injuries,...

Intelligent access key Refer to Intelligent Access in this section for more features. Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment. The typical operating range for your transmitter is approximately 33 f...

Intelligent access (if equipped) WARNING: Radio waves from the intelligent access system transmitters in the vehicle may affect certain implanted medical devices such as pacemakers or cardiac defibrillators. People havingsuch implanted medical devices should ask the medical devicemanufacturer or the...

Push button start: Your vehicle is equipped with a push button start system, which allows you to start your vehicle without using a key. Tooperate the push button start system and start your vehicle, your IA keymust be present inside the vehicle, either in the passenger compartmentor in the trunk. R...

Car finder Press twice within three seconds. The horn will chirp and the turn lamps will flash. It is recommended that this method be used to locateyour vehicle, rather than using the panic alarm. Sounding a panic alarm Press to activate the alarm. The horn will sound and the turn lamps will flash f...

• 10–way power seats • 8–way power seats 2. Press and hold control button 1 for five seconds. A tone will be heardafter two seconds confirming memory position has been set. Continue tohold until a second tone is heard after five seconds. 3. Within three seconds press the . 4. A tone will be heard wh...

Replacing the battery The integrated keyhead transmitter (IKT) or intelligent access key (IAkey) uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: Integrated keyhead transmitter(IKT) 1. Twist a thin coin in the slot nearthe key ring to remove the batterycove...

2. Remove the old battery. Note: Please refer to local regulations when disposing oftransmitter batteries. 3. Insert the new battery. Refer tothe instructions inside the IA keyfor the correct orientation of thebattery. Press the battery down toensure that the battery is fullyseated in the battery ho...

• after 25 seconds of illumination. The lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Illuminated exit • When all vehicle doors are closed, the ignition is turned off and thekey is removed from the ignition (IKT only), the interior dome lamps...

SECURICODE™ KEYLESS ENTRY SYSTEM The keypad, located near the driver’s window, is invisible until touchedand then it lights up so you can see and touch the appropriate buttons. Note: If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter your entry code more ...

two-stage unlocking, refer to the Central unlocking/two stage unlocking section earlier in this chapter. To unlock all doors, enter the factory set code or your personal code, then press the 3 • 4 control within five seconds. Note: If equipped with intelligent access, if the intelligent access key i...

engine. If a problem occurs, turn the ignition off, remove all objects onthe key chain away from the coded key and restart the engine. Note: Do not leave a duplicate coded key in the vehicle. Alwaystake your keys and lock all doors when leaving the vehicle. Anti-theft indicator The anti-theft indica...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help protect your vehicle fromunauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL integrated keyhead transmitters or intelligent access keys are brought to the authorized dea...

• Press and hold the 7 • 8 and 9 • 0 controls on the keyless entrypad at the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdownwhen any of the above actions occurbefore the vehicle becomes armed. Each door, the hood or the trunk isarmed individually, and if any ...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

Press either up or down on thelumbar control to select the top,middle, or bottom part of the seatback. Push and hold the front of thelumbar control to increase thefirmness of the selected portion ofthe seatback or push and hold therear of the lumbar to decrease thefirmness. We recommend first select...

Press the control to recline theseatback forward or rearward. Note: On vehicles with memory seats, to prevent damage to the seat, the power seats are designed to set a stopping position just short of theend of the seat track. If the seat encounters an object while movingforward or backward, a new st...

WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physicalconditions, must exercise care when using the seat heater. The seatheater may cause burns even at low temperatures, e...

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on theseat. Allow the seat to dry thoroughly. To operate the heated seats: Press once to activate the high heatsetting (three indicator lights).Continue pressing to scro...

• There is a filter located undereach front seat. • The filter can be accessed from the rear of the seat. Move the frontseat to full up to ease access. To remove an air filter: 1. Remove key from ignition. 2. Push up on the outside rigid edgeof the filter until the tabs arereleased, then rotate the ...

2. Simultaneously press and holdboth the adjust/release button andthe unlock/remove button, then pullup on the head restraint. To reinstall the adjustable head restraint, do the following: 1. Insert the two stems into theguide sleeve collars. 2. Push the head restraint downuntil it locks. Properly a...

The indicator light will illuminate when the heated seats have beenactivated. SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System™ provides an improved overall level offrontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related i...

appropriate to activate these safety devices. Front airbags are designedto activate only in frontal and near-frontal collisions (not rollovers, sideimpacts or rear impacts) unless the collision causes sufficientlongitudinal deceleration. The pretensioners are designed to activate infrontal and near-...

WARNING: Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The front passenger sensing system can automatically turn off thepassenger front airbag. The system is designed to help protect small(child size) occupants from airbag dep...

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety belt pretensioners, front safety belt buckle sensors, driver seatposition sensor, and front passenger sensing system. In addition, theRCM also monitor...

WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the ...

2. To unfasten, press the releasebutton and remove the tongue fromthe buckle. Energy management feature — front outboard • This vehicle has a safety belt system with an energy managementfeature at the front seats to help further reduce the risk of injury inthe event of a head-on collision. • The ene...

When to use the automatic locking mode This mode should be used any time a child safety seat (except a booster) is installed in a passenger front or rear seating position with acombination lap/shoulder safety belt. Children 12 years old and undershould be properly restrained in a rear seating positi...

How to disengage the automatic locking mode WARNING: Ford Motor Company recommends that all passenger safety belt assemblies and attaching hardware should be inspected by an authorized dealer after any collision to verify thatthe ⬙ automatic locking retractor ⬙ feature for child seats is still worki...

WARNING: The driver and front passenger safety belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results indeployment of front airbags, seat-mounted side airbags and SafetyCanopy 威 , and safety belt pretensioners. Safety ...

If... Then... The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km/h) and more than1-2 minutes have elapsed sincethe ignition has been switchedon... The Belt-Minder 威 feature is activated - the safety belt warning l...

Reasons given... Consider... “Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many when no other vehicles are around. “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’t...

• This will enable the Belt-Minder 威 feature for that seating position if it is currently disabled. As confirmation, the safety belt warning light willflash four times per second for three seconds, followed by threeseconds with the light off, then followed by the safety belt warninglight flashing fo...

Important supplemental restraint system precautions Airbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest close tothe trim covering the airbag module. WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belt...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbaginflation. The fact that the airbagsdid not inflate in a collision does n...

• the system determines that an infant is present in a rear-facing infantseat that is installed according to the manufacturer’s instructions, • the system determines that a small child is present in a forward-facingchild restraint that is installed according to the manufacturer’sinstructions, • the ...

WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).C...

WARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a back-up tone to indicate the cond...

WARNING: Do not attempt to service, repair, or modify the Safety Canopy 威 system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy 威 . See your authorized dealer. WARNING: All occupants of the vehicle including the driver should always wear their safety...

WARNING: If the Safety Canopy 威 system has deployed, the Safety Canopy 威 will not function again unless replaced.The Safety Canopy 威 system (including the A, B, C, and Dpillar trim and headliner) must beinspected and serviced by anauthorized dealer. If the SafetyCanopy 威 is not replaced, it will not...

The system can be turned off when any one of the following actions aretaken by the driver or any other person: • pressing the hazard control button, • or pressing the panic button on the remote entry transmitter. The feature will continue to operate until the vehicle runs out of power. Disposal of a...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) or less(generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier,convertible seat,or toddler seat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

Transporting children Always make sure your child is secured properly in a device that isappropriate for their age, height and weight. All children are shapeddifferently. The child height, age and weight thresholds provided arerecommendations or the minimum requirements of law. The NationalHighway T...

SAFETY SEATS FOR CHILDREN Infant and/or toddler seats Use a safety seat that is recommended for the size and weight of thechild.When installing a child safety seat: • Review and follow the informationpresented in the Airbag supplemental restraint system(SRS) section in this chapter. • Carefully foll...

All the LATCH lower anchors are equally spaced, 280 mm (11 inches)apart, so that a single LATCH child seat can be installed at any rearseating position. If two child safety seats are installed using the LATCH lower anchors, they must be placed in the outboardseating positions only. If three child sa...

Combining safety belt and LATCH lower anchors for attachingchild safety seats When used in combination, either the safety belt or the LATCH loweranchors may be attached first, provided a proper installation is achieved.Attach the tether strap afterward, if included with the child seat. Referto Recom...

2. Locate the correct anchor for theselected seating position. 3. Open the tether anchor cover. 4. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 5. Tighten the child safety seat te...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increasedrisk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat buildup a...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your tire pressure monitoring system (TPMS) The tire pressure monitoring system measures pressure in your four roadtires and sends the tire pressure readings to your vehicle. The low tirepressure warning lamp will turn on if the tire pressure is significantlylow. Once the light is illu...

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Please refer to thefollowing chart for information conc...

Low tire pressurewarning light Possible cause Customer action required Flashing warninglight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

SUMMER TIRES Your Taurus SHO may be equipped with summer tires to providesuperior performance on wet and dry roads. Summer tires do not havethe Mud and Snow (M+S or M/S) tire traction rating on the tire sidewall. Since summer tires do not have the same traction performance asAll-season or Snow tires...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. Tires, Wheels and Loading 232 2010 Taurus (500) Owners Guide, 3rd PrintingUSA (fus)

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now youhave the load capacity to transport the cement and your friend home.In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (9 x45 kg) = 635 - 198 - 405 = 32 kg. The above calculations also assume that the loads are position...

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

• Allow more distance for stopping with a trailer attached; anticipatestops and brake gradually. Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance information for more information. Trailer tow...

Front-wheel drive (FWD) vehicles: Tow your FWD vehicle with all four wheels on the ground or with thefront wheels off the ground by using a tow dolly. If you are using a towdolly follow the instructions specified by the equipment provider. All-wheel drive (AWD) vehicles: Tow your AWD vehicle with al...

STARTING Positions of the ignition (if equipped) If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. 1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessorie...

3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive. Note: If the engine does not start on the first try, turn the vehicle to the off position, wait 10 seconds and try Step 2 again. If the engine still failsto start, press the accelerator to the fl...

Fast Restart Feature: The Fast Restart feature allows you to re-start your vehicle within 20 seconds of switching the vehicle off, if a valid IAkey is not present when the vehicle is switched off. When you switchyour vehicle off without an IA key in the passenger compartment ortrunk, the message RES...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 1 inch (2.5 cm) or adjust the heating orair conditioning to bring in fresh air. ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant...

Even when the ABS is disabled,normal braking is still effective. Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake systemserviced immediately. Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal...

During ESC events the stability control light in the instrument clusterwill flash. Certain adverse driving maneuvers may activate the ESC system, whichinclude but are not limited to: • Taking a turn too fast • Maneuvering quickly to avoid an accident, pedestrian or obstacle • Driving over a patch of...

WARNING: If the message SERVICE POWER STEERING is displayed in the message center, the EPS system has detected a problem with the system function. On the next key cycle the messageSERVICE POWER STEERING NOW will be displayed and steeringassist will be removed until the steering system is serviced. H...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this p...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this p...

Recommended shift speeds Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 15 mph (24 km/h) 2 - 3 25 mph (40 km/h) 3 - 4 40 mph (64 km/h) 4 - 5 45 mph (72 km/h) 5 - 6 50 mph (80 km/h) The instrument cluster will show thecurrent...

Night time and dark area use At night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore it is necessary that bothreverse lamps are operating in order to get a clear image in the dark. Ifeither of the lamps are not operating, stop using the cam...

Operation The radar sensor detects vehiclesahead that are moving in the samedirection as your vehicle. If the radar detects that yourvehicle is rapidly closing on anothervehicle a red warning light willilluminate and an audible warningchime will sound. After that, if the risk of collisionfurther inc...

WARNING: The collision warning system’s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’s brakes. The brake pedal must be pressedjust like for any typical braking situation. Blocked sensor If a message regarding a blockedsensor is displayed,...

The CTA system detects vehicles approaching up to 45 feet (14 meters)away. Coverage decreases when vehicles and objects in close proximityblock the CTA sensors (refer to figure for approximate zone coverageareas [sensor obstructed for vehicle on left] ). Backing slowly from the parking spot in these...

The following table lists possible causes and actions for this messagebeing displayed: The surface of the radar is dirty orobstructed in some way Clean the fascia area in front ofthe radar, either side, or removeobstruction. The surface of the radar is notdirty or obstructed Drive normally in traffi...

ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. The AWD system is an active system, meaning it not onlyresponds to wheel slip between the front and rear axles but also has theability to anticipate wheel slip and transfer torque to...

Driving on slippery surfaces with AWD vehicles AWD vehicles are specially equipped for driving on sand, snow, mud andrough roads and have operating characteristics that are somewhatdifferent from conventional vehicles, both on and off the highway. When driving at slow speeds off-highway under high o...

Do not rock the vehicle for more than a few minutes or damageto the transmission and tires may occur or the engine mayoverheat. WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave ...

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness areas. Ford MotorCompany joins the U.S. Forest Service and the Bureau of LandManagement in encouraging you to help preserve our national forest andother ...

Any modifications to a vehicle that raise the center of gravity can makeit more likely the vehicle will rollover as a result of a loss of control.Ford Motor Company recommends that caution be used with any vehicleequipped with a high load or device (such as ladder or luggage racks). Failure to maint...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Passenger compartment fuse panel The fuse panel is located under the instrument panel to the left of thesteering wheel. The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Left front power window, Smartwindow motor 2 15A Brake on/off switch 3 15A Driver power...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 27 20A Ignition switch, PEPS, Frontwipers, One-touch integrated start(OTIS) 28 5A Start relay/Audio mute 29 5A Instrument panel cluster,Heads-up display 30 5A Not used (spare) 31 10A Not used (spare) 32 10A Airbag module 33 10A Not used (spare) ...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 47 30A Circuit Breaker Front passenger power window,Rear power windows 48 — Delayed accessory relay Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses tha...

WARNING: Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, itwill no longer function. Dissimilar spare tire/wheel information WARNING: Failure to follow these guidelines could resul...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability 3. Fu...

Stopping and securing the vehicle 1. Park on a level surface, set theparking brake and activate hazardflashers. 2. Place gearshift lever in P (Park)and turn engine off. Removing the spare tire and jack 1. Lift the trunk cargo cover, andremove the wing nut that securesthe spare tire by turning itcoun...

3. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground. Note : DO NOT LIFT ON THE PLASTIC MOLDING, as this coulddamage the molding. ONLY LIFT ONTHE SHEET METAL NOTCH. 4. Remove the lug nuts with the lug wrench. 5. ...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Place theextension bolt into the externalpocket of the felt bag. Take care toposition the jack as shown to ensurethat the locating holes in the jack...

If you are stowing the flat tire: 1. Remove the extension bolt fromthe exterior pocket of the felt bag. 2. Install the jack as shown inStep 4 under Stowing the tire and jack . 3. Screw the extension bolt onto thethreaded stud of the jack retentionbracket. 4. With the temporary spare tire onthe vehic...

• Read the information in the Tips for use of the temporary mobility kit section to ensure safe operation of the temporary mobility kit and your vehicle. Tips for use of the temporary mobility kit Read the following list of tips to ensure safe operation of the temporarymobility kit: • Before operati...

• When inflating a tire or other objects, use the black air hose only. Donot use the transparent hose which is designed for sealant applicationonly. • Operating the temporary mobility kit could cause an electricaldisturbance in radio and DVD player operation. What to do when a tire is punctured A ti...

4. Plug the power cable into the 12Vpower point in the vehicle. 5. Remove the warning sticker found on the canister and place it on thetop of the instrument panel or the center of the dash. 6. Start the engine (only if the vehicle is outdoors or in a well-ventilated area) . 7. Turn dial (1) counterc...

Note: When the sealing compound is first added into the tire, theair pressure gauge reading on the compressor unit may indicate ahigher value; this is normal and should be no reason for concern.The pressure will drop after about 30 seconds of operation. Thetire pressure has to be checked with the co...

3. Turn the dial clockwise to the air position. Turn on the kit by pressingthe on/off button. 4. Adjust the tire to therecommended inflation pressurefrom the tire label located on thedriver’s door or door jam area.Pressing the deflation button nearthe sealant canister removes airfrom the tire. Note:...

Removal of the Sealant Canister from the Temporary Mobility Kit 1. Unwrap the clear tube from thecompressor housing. 2. Press the button located on thetemporary mobility kit compressorhousing below the canister whilepulling up on the sealant canister. Installation of the Sealant Canister to the Temp...

2. Once aligned, seat the sealantcanister by lightly pushing downuntil you hear an audible click. 3. Wrap the clear tube around thecompressor housing. Note: If you experience any difficulties with the removal or installation of the sealant canister, consult your Ford Motor Company authorizeddealer f...

Bolt size Wheel lug nut torque* ft-lb N • m 1/2-20 UNF 100 135 * Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford recommended replacement fasteners. WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mountin...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Tar Remover (ZC-42). WINDOWS ...

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft 威 Spot and Stain Remover (ZC-14). In Canada, use Motorcraft 威 Multi-Purpose Cleaner (CXC-101). • If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or th...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance and Specificat...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap ...

Engine shield Some vehicles may be equippedwith an aero-shield under theengine. This shield needs to beremoved for service, including oiland filter changes. It is secured withfour screws. WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optim...

5. Locate and carefully remove theengine oil level dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the...

• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions,...

Use SAE 5W-20 engine oil Only use oils certified for gasoline engines by the American PetroleumInstitute (API). An oil with this trademark symbol conforms to thecurrent engine and emission system protection standards and fueleconomy requirements of the International Lubricant Standardization andAppr...

For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe battery terminals. If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neut...

Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe battery is disconnected or a new battery is installed, the engine mustrelearn its idle and fuel trim strategy for optimum driveability andperformance. To...

ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water,which equates to a freeze point of -34°F (-36°C). Co...

Note: Automotive fluids are not interchangeable; do not use engine coolant/antifreeze or windshield washer fluid outside of its specifiedfunction and vehicle location. Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to ...

• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the enginecoolant. For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when the eng...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine c...

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cool...

WARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certainconditions. Care should be taken to avoid inhaling excess fumes. WARNING: The flow of fuel through a fuel pump no...

Easy Fuel™ “no cap” fuel system Your fuel tank is equipped with an Easy Fuel™ “no cap” fuel fillersystem. This allows you to simply open the fuel filler door and insert thefuel filler nozzle into the fuel system. The Easy Fuel™ system isself-sealing and protected against dust, dirt, water and snow/i...

WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel™ “no cap” fuel system), do not refuel until the sound stops. Otherwise, fuel mayspray out, which could cause serious personal injury. Choosing the right fuel Use only UNLEADED fuel or UNL...

Some stations offer fuels posted as ⬙ Regular ⬙ with an octane rating below 87, particularly in highaltitude areas. Fuels with octanelevels below 87 are notrecommended for either engine. Do not be concerned if your enginesometimes knocks lightly. However, if it knocks heavily while you areusing fuel...

2. Slowly insert the funnel into theEasy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container. 4. When done, clean the funnel or properly dispose of it. Extra funnelscan be purchased from your authorized dealer if you choose to disposeof the funnel. Do not use aftermarket fun...

The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the empty reserve still pres...

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to changea number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually gi...

If other than Ford, Motorcraft 威 or Ford-authorized parts are used for maintenance replacements or for service of components affectingemission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability. WARNING: Do not park, idle, or drive your...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performan...

C. Remove the bolt cover (ifequipped). D. Remove two bolts that attach the air filter assembly to the front ofthe vehicle (2). E. Loosen the clamp holding the air filter assembly to the rubber hose(1). F. Remove the harness retaining clip by pulling up (3). Do notdisconnect the sensor (4). G. Withou...

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter elementlisted. Refer to Motorcraft 威 part numbers in this chapter. WARNING: To reduce the risk of vehicle damage and/...

4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing. 5. Install a new air filter element. Be careful not to crimp the filterelement edges between the air filter housing and cover. This could causefilter damage and allow unfiltered air to enter the en...

ENGINE DATA Engine 3.5L V6 engine 3.5L V6 SHO engine Cubic inches 214 214 Fuel See Octane recommendations earlier in this chapter. See Octane recommendations earlier in this chapter. Firing order 1–4–2–5–3–6 1–4–2–5–3–6 Ignition system 0.052–0.056 inch (1.32–1.42 mm) 0.033–0.037 inch (.838–.939 mm) ...

TRANSMISSION CODE DESIGNATIONS You can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmission each coderepresents. Description Code 6F50 6-Speed Automatic Transmission J 6F55 6–Speed Automatic Transmission (withEcoBoost) C Maintenance and...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight cap...

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up to ...

A Accessory delay ..........................84 Adaptive Cruise Control .............89 AdvanceTrac ..............................251 AdvanceTrac Sport Mode .........256 Air cleaner filter ...............368–369 Air conditioning ....................50, 53 automatic temperaturecontrol system ............

fluid, checking and adding(automatic) .............................363 Trunk .........................................126 remote release ................111, 131 Turn signal ..................................68 U Universal garage door opener ..100 USB port ......................................42 V ...