Ford 2009 Taurus v.3- User Manual

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

To access this information, special equipment must be directlyconnected to the recording modules. Ford Motor Company andFord of Canada do not access event data recorder informationwithout obtaining consent, unless pursuant to court order orwhere required by law enforcement, other government authorit...

Export unique (Non–United States/Canada) vehicle specificinformation For your particular global region, your vehicle may be equipped withfeatures and options that are different from the features and options thatare described in this Owner’s Guide. A market unique supplement may be supplied that comp...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Check fuel cap (if equipped): Illuminates when the fuel cap maynot be properly installed. Cont...

Airbag readiness: If this light fails to illuminate when the ignition isturned to on, continues to flash orremains on, have the systemserviced immediately by your authorized dealer. A chime will soundwhen there is a malfunction in the indicator light. Safety belt: Reminds you to fasten your safety b...

Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be checked. Referto Inflating your tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to on, the light will illuminate for...

AUDIO SYSTEMSQuick start — How to get going WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The drivers primary responsibility is the s...

For a single CD system, if a disc is not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the display. The firsttrack on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot numbe...

While in folder mode, pressFOLDER to access the next folder on MP3 discs, if available. Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random play. Otherwise,random play will begin when the current track is...

COMPRESS (Compression): Available only in CD/MP3 mode. Press MENU until COMPRESS ON/OFF appears in the display. Use / to toggle ON/OFF. When COMPRESS is ON, the system will bring the softand loud CD passages together for a more consistent listening level. 4. AUX: Press repeatedly to cycle through LI...

7. SHUFFLE: Press SHUFFLE to engage shuffle mode. SHUFFLE ONwill appear in the display. If youwish to engage shuffle mode right away, press SEEK to begin randomplay. Otherwise, random play will begin when the current track isfinished playing. CD SHUF will appear in the display.To disengage, press SH...

17. LOAD: To load a disc into the system, press LOAD. Select a slotnumber using memory presets 1–6.When the display reads LOAD CD#,load the desired disc, label side up.If you do not choose a slot within five seconds, the system will choosefor you. To auto load up to six discs, press and hold LOAD un...

Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers withhigh fidelity. To achieve optimalperfor...

Your vehicle may be equipped with aUSB port inside your center console.This feature allows you to plug inmedia playing devices, memorysticks, and also to charge devices ifthey support this feature. Forfurther information on this feature,refer to Accessing and using your USB port in the SYNC 威 supple...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS satellite or SIRIUS tower to the vehicle antenna. You are in a location that i...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Airflow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes ...

4. Rear defroster: Press to activate/deactivate rear window defroster. Refer to Rear window defroster in this section for more information. 5. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engagesautomatically in MAX A/C,...

4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents toward the side windows. DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from the...

Dual Zone Automatic Temperature Control with heated seats(if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. Press to return to the previous airflow mode. The system will automatically provide...

automatically with selection of MAX A/C or can be engaged manually inany other airflow selection except (defrost). Recirculation may turn off automatically in all airflow selections except MAX A/C. When the ignition switch is turned off and back on, the climate systemwill return to the recirculated ...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Press A/C. 3. Adjust the temperature to the warmest setting. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents toward the side windows. REAR WINDOW DEFROSTER R The rear defroster control i...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled b...

3. Turn the ignition switch to on and then back to off. 4. Turn the headlamp control to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamps off. Fog lamp control With the ignition on, the fog l...

Flash to pass Pull toward you to activate andrelease to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the on position, • the headlamp control is in the off, autolamps or parking lamp positionand • the transm...

Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmerswitch from the full dim position to the full dome/on position to reset.This will ensure that your displays are visible under all lightingconditions. AIMING TH...

Your vehicle may also have readinglamps within the rear dome lamp(s). Press the switches on either side ofthe dome lamp to turn on thelamps. BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product of thi...

2. Remove the press pin and cargonet fastener (if equipped) andcarefully pull the carpet away toexpose the backside of the tail lampassembly. 3. Remove the nut and washerassemblies, then pull the lampassembly away from the vehicle. 4. Remove the bulb socket byrotating it counterclockwise, thenpullin...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down and hold the steeringwheel release control. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Pull the steering wheel releasecontrol up. This will lock thesteering wheel in position. WARNING: Never adjust the st...

INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may beused to secure sunglasses or similarsized objects. Press the button toopen the storage compartment. OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment The...

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Theseinclude: 1. Cupholders 2. Utility compartment with coinholder, a clamshell tray, audio inputjack, USB port and power point 3. Rear power point, vent and (ifequipped) a cupholder 4. Pen holder WARNING: Use only soft ...

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe battery from being discharged: • do not use the power point longer than necessary when the engine isnot running, • do not leave battery chargers, video ...

Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (to the first detent) andhold the switch to close. Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or bu...

Bounce-back (driver’s window only) When an obstacle has been detected in the window opening as thewindow is moving upward, the window will automatically reversedirection and move down. This is known as “bounce-back”. If the ignitionis turned off (without accessory delay being active) during bounce-b...

EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish t...

The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control(located on the instrument panel) toadjust accelerator and brake pedal. • Press the top of the control toadjust the pedals away from ...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...

• Depress the brake pedal or pressCNCL (Cancel) until the desiredvehicle speed is reached, pressthe SET + control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or pressCNCL (Cancel). This will noterase your vehicle’s previously setspeed. • Pre...

In AM, FM1, or FM2 mode: • Press SEEK to access thenext/previous strong station. In Satellite radio mode (ifequipped): • Press and release SEEK to accessthe next/previous preset. • Press and hold SEEK to fastadvance through subscribedchannels in the current category. In CD mode: • Press SEEK to list...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a convenient way toreplace up to three hand-heldtransmitters with a single built-indevice. This feature will learn theradio frequency codes of mosttransmitters to operate g...

1. Position the end of yourhand-held transmitter 1–3 inches(2–8 cm) away from the HomeLink 威 button you wish to program (locatedon your visor) while keeping theindicator light in view. 2. Simultaneously press and holdboth the chosen HomeLink 威 and hand-held transmitter buttons until the HomeLink 威 i...

Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink 威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined inthe Programming section, replace Step 2 with the f...

Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the train...

1. To disable/enable the autolampdelay feature, select this functionfrom the SETUP control for thecurrent display mode. 2. Press the RESET control to selectthe new Autolamp delay values of 0,10, 20, 30, 60, 90, 120 or 180 seconds. Autolock (if equipped) This feature automatically locks all vehicle d...

CARGO AREA FEATURES Cargo net (if equipped) The cargo net secures lightweightobjects in the cargo area. Attach thenet to the anchors provided. Do notput more than 50 lb. (22 kg) in thenet. WARNING: This net is not designed to restrain objects during a collision. Driver Controls 95 2009 Taurus (500) ...

KEYS Your vehicle may be equipped withtwo Integrated KeyheadTransmitters (IKTs). The key bladefunctions as a programmed keywhich starts the vehicle andunlocks/locks all the doors. Thetransmitter portion functions as theremote entry transmitter. Your IKTs are programmed to your vehicle; using a non-p...

When inserting the IKT into theignition cylinder, place your thumbon the center thumb rest of the IKTand forefinger on the logo badge onthe opposite side. To gain more leverage when rotatingthe IKT in the ignition lock cylinder,you can readjust the location ofyour thumb to grasp the IKT on theouter ...

Smart locks This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open one of the front doors and you lock the vehicle with thepower door lock control (on the driver or passenger door trim panel), allthe doors will lock, then all doo...

Power door lock switch autolock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicledoors are closed. You must complete Steps 1–5 within 30 seconds or theprocedure will have to be repeated. If the procedure needs to berepeated, wait a minimum of 30 sec...

6. To enable/disable the autounlock feature, press the lock control, thenpress the unlock control. The horn will chirp once if autounlock wasdeactivated or twice (one short and one long chirp) if autounlock wasactivated.7. Turn the ignition to the off position. The horn will chirp once toconfirm the...

• When the childproof door locks are set, the rear doors cannot beopened from the inside. • The rear doors can be opened from the outside when the power doorlocks are unlocked. INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle ...

WARNING: Do not leave children, unreliable adults, or animals unattended in the vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people oranimals to these high temperatures for even a short time can causedeath or serious heat-related injuries,...

Activating the memory feature To activate this feature: 1. Position the seat, mirrors and adjustable pedals to the desiredpositions. 2. Press and hold either the 1 or 2control on the driver’s door for fiveseconds. (A tone will be heard after1 1 ⁄ 2 seconds when the memory store is done) continue to ...

3. Insert the new battery. Refer tothe instructions inside the IKT forthe correct orientation of thebattery. Press the battery down toensure that the battery is fullyseated in the battery housing cavity. 4. Snap the battery cover back ontothe key. Note: Replacement of the battery will not cause the ...

Perimeter lamps illuminated entry With the Integrated Keyhead Transmitter system, the following items willilluminate when the control on the transmitter is pressed: • Headlamps • Park lamps • Tail lamps The lamps will automatically turn off: • if the ignition switch is turned to the on position, or ...

6. Press the power door unlock control twice within five seconds. Note: The horn will chirp once to indicate the perimeter lighting feature hasbeen deactivated. The horn will chirp once and honk once (one shortand one long) to indicate the perimeter lighting feature has beenactivated. 7. Turn the ig...

SECURICODE™ KEYLESS ENTRY SYSTEM You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • open the trunk. • recall memory seat/power mirrorspositions (if equipped). The keypad can be operated withthe factory set 5–digit entry code;this code is located on the owner’swa...

Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. All personal codes are now erased and only the factory set 5–digit ...

Automatic arming The vehicle is armed immediately after switching the ignition to the offposition. The theft indicator will flash everytwo seconds to act as a theftdeterrent when the vehicle isarmed. Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the onpositi...

Integrated Keyhead Transmitter). The theft indicator light will illuminatefor three seconds and then go out to indicate successful programming. If the key was not successfully programmed, it will not start yourvehicle’s engine and/or will not operate the remote entry features. Thetheft indicator lig...

• Press the 7 • 8 and 9 • 0 controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdownwhen any of the above actions occurbefore the vehicle becomes armed. Each door, the hood, and the trunkis armed individually, and if any areopen...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

Push release button to lower headrestraint. Using the manual lumbar support (if equipped) The lumbar support control islocated on the outboard side of theseatback. Move the control up or down toadjust lumbar support. Folding down the front passenger seatback The front passenger seatback can befolded...

WARNING: Cover sharp edges on the load and properly secure the load to prevent injury to occupants from shifting load during sudden stops. WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the sea...

Pull lever up to adjust seatback. WARNING: Before returning the seatback to its original position, make sure thatcargo or any objects are nottrapped behind the seatback. Afterreturning the seatback to itsoriginal position, pull on theseatback to ensure that it has fullylatched. An unlatched seat may...

Memory seat/power mirrors/adjustable pedals (if equipped) This system allows automaticpositioning of the driver seat,outside rearview mirrors andadjustable pedals to twoprogrammable positions. The memory seat control is locatedon the driver door. • To program position one, move the driver seat, exte...

The head restraints can be movedup by pulling up on the headrestraint. Push the release button to lowerhead restraint. Split-folding rear seat One or both rear seatbacks can be folded down to provide additionalcargo space. To lower the seatback(s) frominside the vehicle, pull the straplocated on the...

levels of crash severity and modify the deployment strategy of thedual-stage airbags and safety belt pretensioners. Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System 威 to tailor the deployment level of the driver dual-stage airbag based on seatpositio...

Safety belt precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while th...

WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident. Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and...

WARNING: Failure to inspect and replace if necessary the belt and retractor assembly after an accident could increase the risk of injury in a collision. All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes o...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode WARNING: Ford Motor Comp...

WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat beltand increase the risk of injury in a collision. Safety belt pretensioner Your vehicle is equipped wi...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• driver and front passenger safety belt pretensioner • a readiness light and tone. • diagnostic module. • the electrical wiring which connects the components. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or “pass airbag of...

The front passenger sensing system will turn off the passenger seat sideairbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing systemuses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind youthat the front passe...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

A difficulty with the system is indicated by one or more of the following: • The readiness light (same lightfor front and side airbag system)will either flash or stay lit. • The readiness light will notilluminate immediately after ignition is turned on. • A series of five beeps will be heard. The to...

How does the side airbag system work? The design and development of the side airbag system includedrecommended testing procedures that were developed by a group ofautomotive safety experts known as the Side Airbag Technical WorkingGroup. These recommended testing procedures help reduce the risk ofin...

WARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety Canopy 威 system is provided. WARNING: To reduce risk of injury, do not obstruct or place objects in the deployment path of the inflatable Safety Canopy 威 . How does the...

WARNING: If the Safety Canopy 威 system has deployed, the Safety Canopy 威 will not function again unless replaced. The Safety Canopy 威 system (including the A, B, C, and D pillar trim and headliner) must be inspected and serviced by an authorized dealer. Ifthe Safety Canopy 威 is not replaced, it will...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, orage Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safety seat(sometimes called aninfant carrier,convertible seat, ortoddler seat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

Transporting children Always make sure your child is secured properly in a device that isappropriate for their age, height and weight. All children are shapeddifferently. The child height, age and weight thresholds provided arerecommendations or the minimum requirements of law. The NationalHighway T...

method eliminates the need to use safety belts to attach the child seat,however the safety belt can still be used to attach the child seat. Forforward-facing child seats, the top tether strap must also be attached tothe proper top tether anchor, if a top tether strap has been providedwith your child...

Attaching child safety seats with tether straps Many forward-facing child safety seats include a tether strap whichextends from the back of the child safety seat and hooks to an anchoringpoint called the top tether anchor. Tether straps are available as anaccessory for many older safety seats. Conta...

3. Open the tether anchor cover. 4. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 5. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If the ...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back be...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Pressure Warning Lamp will turn ON if the tire pressure issignificantly low. Once the light is illu...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

Low TirePressureWarning Light Possiblecause Customer Action Required Flashing WarningLight Spare tire inuse Your temporary spare tire is inuse. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a description ofhow the system functions underthese condition...

under-inflated, carefully drive the vehicle to the nearest location whereair can be added to the tires. Inflate all the tires to the recommendedinflation pressure. SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of a...

• Do not exceed 30 mph (48 km/h) with tire cables on your vehicle. VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly ...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. GCW (Gross Combined Weight) – is the...

WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s pla...

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1,400 - (2 x 220) -(12 x 100) = 1,400 - 440 - 1,200 = - 240 lb. No, you do not haveenough cargo capacity to carry that much weight. In metric units, thecalculation would be: 635 kg - (2 ...

Hitches Do not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch. You must distribute the load in your trailer so that10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the vehic...

• It is recommended to select the L (Low) gear position when additionalengine braking is needed. In situations such as prolonged downhilldriving on steep grades (i.e., driving in mountainous areas), additionalengine braking is needed to reduce the load on the vehicle’s regularbrake system to prevent...

Front Wheel Drive (FWD) vehicles: Tow your Front Wheel Drive vehicle with all four wheels on the groundor with the front wheels off the ground by using a tow dolly. If you areusing a tow dolly follow the instructions specified by the equipmentprovider. All Wheel Drive (AWD) vehicles: Tow your All Wh...

STARTING Positions of the ignition 1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessories off. 2. Accessory— allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. On— all electrical circuits ...

How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth. Depending on the type of factory installed equipment, your engine blockheater will use .4 to 1.0 kilowatt-hours of energy per hour of use. Yourfactory installed block hea...

Brake Assist The Brake Assist system provides full braking force during panic brakingsituations. It detects a rapid application of the brake pedal and uses theABS system to achieve maximum braking pressure. Once a panic brakeapplication is detected, the system will remain activated as long as thebra...

WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle.However, if the normal brakes fail, the parking brake can be used to stopyour vehicle in an emergency. Since the parking brake a...

system will regain all features. Anti-lock braking, and ESC are notaffected by this condition and will continue to function during thecool-down period. The Engine Traction Control and Brake Traction Control system may bedeactivated in certain situations. See the Switching Off AdvanceTrac 威 section b...

If you switch off the AdvanceTrac 威 system the AdvanceTrac “Off” button will illuminate and the sliding car ⬙ icon will illuminate steadily. Pressing the AdvanceTrac 威 ⬙ Off ⬙ button again will turn off the lighted button and the ⬙ sliding car ⬙ icon . In R (Reverse), ABS and the Engine and Brake Tr...

If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift int...

WARNING: Do not drive your vehicle until you verify that the brakelamps are working. WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. WARNING: If the parking brake...

D (Drive) with Overdrive Cancel and Grade Assist Pressing the transmission controlswitch on the side of the gearshiftlever activates two features at thesame time: Overdrive Cancel andGrade Assist. 1. Overdrive Cancel • Overdrive is deactivated. • The transmission operates in gears one through five. ...

ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. The AWD system is an active system, meaning it not onlyresponds to wheel slip between the front and rear axles but also has theability to anticipate wheel slip and transfer torque to...

When driving through water, determine the depth; avoid water higherthan the bottom of the wheel rims (if possible) and proceed slowly. If theignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Dry...

your vehicle is equipped with a four wheel anti-lock brake system (ABS),do not “pump” the brakes. Refer to the Brakes section of this chapter for additional information on the operation of the anti-lock brake system. Maintenance and Modifications The suspension and steering systems on your vehicle h...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

After an accident, if the engine cranks but does not start, this switchmay have been activated. The fuel pump shut-off switch islocated in the front passengerfootwell area in the right uppercorner. To reset the switch: 1. Turn the ignition to the offposition. 2. Check the fuel system for leaks. 3. I...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Passenger compartment fuse panel The fuse panel is located under the instrument panel to the left of thesteering wheel. The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Smart window motor 2 15A Brake on/off switch,High-mounted brake lamp 3 15A SDARS, Bluet...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 36 5A PATS module 37 10A Climate control 38 20A Subwoofer (Audiophile radio) 39 20A Radio 40 20A Not used (spare) 41 15A Moon roof, Front lock switches,Radio, EC Mirror with compass(with and without microphone) 42 10A Not used (spare) 43 10A Not...

WARNING: The use of tire sealants may damage your Tire Pressure Monitoring System and should not be used. WARNING: Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, itwill no longer...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability 3. Fu...

Stopping and securing the vehicle 1. Park on a level surface, set theparking brake and activate hazardflashers. 2. Place gearshift lever in P (Park)and turn engine off. Removing the spare tire and jack 1. Lift the trunk cargo cover, andremove the wing nut that securesthe spare tire by turning itcoun...

3. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground. Note : DO NOT LIFT ON THE PLASTIC MOLDING, as this coulddamage the molding. ONLY LIFT ONTHE SHEET METAL NOTCH. 4. Remove the lug nuts with the lug wrench. 5. ...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Place theextension bolt into the externalpocket of the felt bag. Take care toposition the jack as shown to ensurethat the locating holes in the jack...

If you are stowing the flat tire: 1. Remove the extension bolt fromthe exterior pocket of the felt bag. 2. Install the jack as shown inStep 4 under Stowing the tire and jack . 3. Screw the extension bolt onto thethreaded stud of the jack retentionbracket. 4. With the temporary spare tire onthe vehic...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect t...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

If you cannot find unleaded fuel or can only get fuel with an anti-knockindex lower than is recommended for your vehicle, contact a regionaloffice or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emi...

Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer orby writing to:Ford Motor Company of Canada, LimitedService Publications CHQ202The Canadian RoadP.O. Box 2000Oakville, ON, CanadaL6J 5E4 REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your v...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, su...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

• For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassCleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the w...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean and damp white cotton cloth, then with a clean and dry whitecotton cloth; you may also use Motorcraft Dash & Vinyl Cleaner(ZC-38-A) on the instrument panel and interior tr...

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). In Canada, useMotorcraft Multi-Purpose Cleaner (CXC-101). • If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the rin...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance and Specificat...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 ENGINE 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap ...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optim...

5. Locate and carefully remove theengine oil level dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the...

• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions,...

to the current engine and emission system protection standards and fueleconomy requirements of the International Lubricant Standardization andApproval Committee (ILSAC), comprised of U.S. and Japaneseautomobile manufacturers. To protect your engine and engine’s warranty, use Motorcraft SAE 5W-20or a...

If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with a solution of baking soda and water. It is recommended that the negative battery cable terminal bedisconnected from the battery if you plan to store ...

1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park), turn off all accessories and start theengine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine...

Your vehicle was factory-filled with a 50/50 engine coolant and waterconcentration. If the concentration of coolant falls below 40% or above60%, the engine parts could become damaged or not work properly. A 50/50 mixture of coolant and water provides the following: • Freeze protection down to -34°F ...

WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hotengine parts. WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the...

Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposi...

Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cooling systemand engine protection. What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle tobe driven tempo...

WARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certainconditions. Care should be taken to avoid inhaling excess fumes. WARNING: The flow of fuel through a fuel pump no...

Fuel filler cap Your fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise until it spins off. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align th...

WARNING: If you do not use the proper fuel filler cap, excessive vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result inpersonal injury. Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% etha...

Fuel quality If you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. “Premium”unleaded gasoline is not recommended for vehicles designed to use“Regular” unleaded gasoline because it may cause these problems tobecome more pronounced...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and mayreduce fuel economy. • Resting your foot on the bra...

is not supplied with your vehicle. The EPA fuel economy estimatesshould be your guide for the fuel economy comparisons with othervehicles. Your fuel economy may vary depending upon the method ofoperation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control c...

Readiness for Inspection/Maintenance (I/M) testing Some state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect the emission controlequipment on your vehicle. Failure to pass this inspection could preventyou from getting a vehicle registration. Your vehicle ma...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

High fluid level Fluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/orengagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels...

Changing the air filter element 1. Release the clamps that securethe air filter housing cover. 2. Carefully separate the two halvesof the air filter housing. 3. Remove the air filter elementfrom the air filter housing. 4. Wipe the air filter housing andcover clean to remove any dirt ordebris and to ...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight cap...

A Accessory delay ..........................71AdvanceTrac ..............................209Air cleaner filter ...............293–295Air conditioning ....................48, 50Airbag supplemental restraintsystem ........................139, 148, 150 and child safety seats ............141description ....