Ford 2009 Fusion v.2- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

PERCHLORATE MATERIAL Certain components of this vehicle such as airbag modules, seat beltpretensioners, and button cell batteries may contain Perchlorate Material– Special handling may apply for service or vehicle end of life disposal.See www.dtsc.ca.gov/hazardouswaste/perchlorate. BREAKING-IN YOUR ...

WARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions couldresult in personal injury. WARNING: Front seat mounted rear-facing child or infant seats should NEVER be placed in f...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

Export unique (Non–United States/Canada) vehicle specificinformation For your particular global region, your vehicle may be equipped withfeatures and options that are different from the ones that are describedin this Owner’s Guide. A market unique supplement may be supplied that complements this boo...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

the bulb and to indicate whether the vehicle is ready forInspection/Maintenance (I/M) testing. Normally, the ⬙ Service engine soon ⬙ light will stay on until the engine is cranked, then turn itself off if nomalfunctions are present. However, if after 15 seconds the ⬙ Service engine soon ⬙ light blin...

WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle.Have the vehicle checked by your authorized dealer. Driving extendeddistances with the parking brake engaged can cause ...

Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as saf...

AUDIO SYSTEMSQuick start — How to get going WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The drivers primary responsibility is the s...

For a single CD system, if a disc is not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the display. The firsttrack on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot numbe...

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random play. Otherwise,random play will begin when the current track is finished playing. CDSHUF will appear in the display.To disengage, press SHUFFLE again. ...

In CATEGORY MODE, press SEEK to select a category. Satellite radio is available only with a valid SIRIUS subscription.Check with your authorized dealer for availability. 6. / OK: (Play/Pause): Press to pause the CD that is playing. PAUSE willappear in the display. Press again to return to playback m...

SPEEDVOL (Speed sensitive volume, if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louderwith increasing vehicle speed to compensate for road and wind noise. Use / / SEEK to adjust. Press OK to close and return to the main menu. The default setting is off; incr...

In satellite radio mode (if equipped), press and hold to hear a brief sampling of the next channels. Press again to stop. In CATEGORYMODE, press SCAN to hear a brief sampling of the channels in theselected category. Press again to stop. Satellite radio is available only with a valid SIRIUS radiosubs...

system will eject the disc and the display will read REMOVE CD. If thedisc is not removed in 15 seconds, the system will reload the disc. To auto eject up to 6 CDs, press and hold until the system begins ejecting all loaded discs. If the discs are not removed, the system willreload the discs. 19. CD...

USB port (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is the safeoperation of thei...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS satellite or SIRIUS tower to the vehicle antenna. You are in a location that i...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

6. Fan speed adjustment: Controls the volume of air circulated in the vehicle. Manual heating and air conditioning system operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do n...

4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. AUTOMATIC TEMPERATURE CONTROL (ATC) SYSTEM(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center, refer to...

Automatic Temperature Control (ATC) system operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle, do not drive with thesystem OFF, or with recirculated air engaged and A/C off. • Do...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled b...

Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmerswitch from the full dim position to the full dome/on position to reset.This will ensure that your displays are visible under all lightingconditions. AIMING TH...

Your vehicle may also have readinglamps within the rear dome lamp(s). Press the switches on either side ofthe dome lamp to turn on thelamps. Ambient/Mood lighting (if equipped) Illuminates four footwells, twoconsole cupholders and the consolebin with a choice of seven colors.The ambient lighting con...

7. For ease of bulb socket installation into the lamp assembly, hold thebulb socket at 15 degrees clockwise from a vertical position. Use the twolead wires oriented up to represent the vertical reference position. 8. From the 15 degree position, rotate the bulb socket clockwise to alocked position. ...

Replacing fog lamp bulbs (if equipped) 1. Make sure the fog lamp switch isin the off position. 2. From underneath the vehicle,partially remove the tire splashshield by removing four drivescrews. After removing to allow free accessto the front fog lamp bulb andelectrical wire harness, the splash shie...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is set on the intermittent settings, the speed of the wipers will automatically ...

TILT/TELESCOPE STEERING WHEEL To adjust the steering wheel: 1. Pull the lever down to unlock thesteering column. 2. While the lever is in the downposition, move the steering wheelup or down and in or out until youfind the desired position. 3. While holding the steering wheelin place, pull the lever ...

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment Press on the rear edge of thecompartment door to open. The storage compartment may beused to secure sunglasses or asimilar object. CENTER CONSOLE Your vehic...

CLOCK (IF EQUIPPED) Press the right (+) control to movethe time display forwards. Press the left (-) control to movethe time display backwards. INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may beused to secure sunglasses or similarsized objects. Press the button toopen the storage co...

12 VDC/180W. If the power point or cigar lighter socket is not working, afuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses. To have full capacity usage of your power point, the engine is required tobe running to avoid u...

Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (to the first detent) andhold the switch to close. Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or bu...

WARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror (if equipped) Your vehicle may be equipped with an interior rear view mirror that hasan auto-dimming function. The electronic day/night mirror will changefrom the normal (high reflective) st...

To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Heated mirrors (if equipped) ...

The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator light on the instrument cl...

Turning off speed control There are two ways to turn off the speed control: • Press the OFF control. • Turn off the ignition. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features Press ME...

Navigation system/SYNC handsfree control features (ifequipped) Press control briefly until the voice icon appears on the Navigation display to use the voicecommand feature. Press to activate phone mode or answer a phone call. Press andhold to exit phone mode or end a call.For further information on ...

Bounce-back: When an obstacle has been detected in the moon roof opening as themoon roof is closing, the moon roof will automatically open and stop at aprescribed position. This is known as “bounce-back”. If the ignition isturned off (without accessory delay being active) during bounce-back,the moon...

by a brief indicator chime. The system will also notify you of potentialvehicle problems with a display of system warnings followed by a longindicator chime. Selectable features Reset Press this control to select and resetfunctions shown in the INFO menuand SETUP menu. Info menu This control display...

Units (English/Metric) 1. Select this function from theSETUP menu for the current unitsto be displayed. 2. Press the RESET control tochange from English to Metric. Language 1. Select this function from theSETUP menu for the currentlanguage to be displayed. 2. Pressing the RESET controlcycles the mes...

1. Select this function from theSETUP menu to disable the reversesensing system feature. 2. Press the RESET control to turnthe rear park assist off. When R(Reverse) gear is selected, PARK AID OFF will be displayed. System warnings System warnings alert you to possible problems or malfunctions in you...

TIRE PRESSURE MONITOR FAULT — Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on orcontinues to come on, contact your authorized dealer as soon aspossible. TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressure sensor is malfunctioning, or your spare t...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and a remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non-programmed keywill not permit your ve...

Recommended handling of the Integrated Keyhead Transmitter(IKT) To avoid inadvertently activating the remote entry functions of yourvehicle, it is recommended that the Integrated Keyhead Transmitter(IKT) be handled properly when starting and turning off your vehicle. When inserting the IKT into thei...

• Turning the key in the ignition to the on position. Note: This feature is configured off by default. This feature can be turned on or off using the following procedure: Before starting, ensure the ignition is in the off position and all vehicledoors are closed. You must complete Steps 1–5 within 3...

6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has beenenabled. Autounlock feature The autounlock feature will unlock all the doors when: • the ignition is in the on position, all the doors are ...

4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the on position. The horn will chirp one timeto confirm programming mode has been entered and is active. 6. To enable/disable the autounlock feature, press the lock control, thenpress the unlock contro...

• Insert the key and turn to the unlock position (key horizontal) todisengage the childproof locks. INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they beco...

WARNING: Do not leave children, unreliable adults, or animals unattended in the vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people oranimals to these high temperatures for even a short time can causedeath or serious heat-related injuries,...

To replace the battery: 1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing o...

The illuminated entry system will turn off the interior lights if: • the ignition is turned to the on position, • the Integrated Keyhead Transmitter lock control is pressed, • The vehicle is locked using the keyless entry keypad (if equipped), or • after 25 seconds of illumination. The inside lights...

1. Place the key in the ignition andturn the ignition to the 3 (on)position. 2. Press the power door unlockcontrol on the door panel threetimes. 3. Turn the ignition from the 3 (on)position to the 1 (off) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ign...

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • open the trunk. The keypad can be operated with the factory set 5–digit entry code; thiscode is located on the owner’s wallet card in the glove box and isavailable ...

The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the control on the remote entry transmitter portion of your Integrated Keyhead Transmitter. • the ignition is turned on. Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the...

The theft indicator will illuminate for three seconds and then go out. Ifthe theft indicator stays on for an extended period of time or flashesrapidly, contact your authorized dealer as soon as possible. Replacement Integrated Keyhead Transmitters (IKT) and codedkeys Note: Your vehicle comes equippe...

Please read and understand theentire procedure before you begin. 1. Insert the first previouslyprogrammed coded key into the ignition. 2. Turn the ignition from the 1 (off)position to the 3 (on) position. Keepthe ignition in the 3 (on) positionfor at least three seconds, but no more than 10 seconds....

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter portion ofyour Integrated Keyhead Transmitter. • Unlocking the doors using the keyless entry keypad (if equipped). • Unlock the driver’s door with a key. Turn the ...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation. Pull lever up to adjust seatback. Folding down the front passenger seatback (if equipped) The front passenger seatback can be folded to a horizontal position tomake room for a long load. To fold...

WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its originalposition, pull on the seatback to ensure that it has fully latched. Anunlatched seat may become dangerous in the event...

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on theseat. Allow the seat to dry thoroughly. The heated seats will only function when the ignition is in the onposition. To operate the heated seats: • Push the control...

to the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the airbag. For otheroccupants, this occurs when the occupant is not properly restrained bysafety belts or child safety seats and they move forward during pre-crashbraking. The mo...

Front safety belt energy management retractors The front outboard safety belt energy management retractors allowwebbing to be pulled out of the retractor in a gradual and controlledmanner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occup...

Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue issecurely fastened in the buckle. 2. To unfasten, push the releasebutton and remove the tongu...

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movem...

This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children12 years old and under should be properly restrained in a rear seatingposition whenever possible. Refer to Safety restraints for children or Safety seats for ch...

Safety belt height adjustment Your vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder belt so the belt restsacross the middle of your shoulder. To adjust the shoulder belt height,pull on the center button and slidethe height adjuster up...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rareevents” 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events,even for good drivers. 1 in 4 of us will be ser...

WARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s air bagsystem. One-time disable If at any time the driver/front passenger quickly buckles then unbucklesthe safe...

1. Turn the ignition switch to the on position. DO NOT START THEENGINE. 2. Wait until the safety belt warning light turns off (Approximately1–2 minutes). • Step 3 must be completed within 50 seconds after the safety beltwarning light turns off. 3. For the seating position being disabled, at a modera...

Important supplemental restraint system precautions Airbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest close tothe trim covering the airbag module. WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belt...

are not properly restrained or are otherwise out of position at the timeof airbag deployment. Thus, it is extremely important that occupants beproperly restrained as far away from the airbag module as possible whilemaintaining vehicle control. WARNING: Several air bag system components get hot after...

The front passenger sensing system works with sensors that are part ofthe front passenger’s seat and safety belt. The sensors are designed todetect the presence of a properly seated occupant and determine if thefront passenger’s frontal airbag should be enabled (may inflate) ordisabled (will not inf...

• Objects between the seat cushion and the center console (ifequipped) • Objects hanging off the seat back • Objects stowed in the seatback map pocket (if equipped) • Objects placed on the occupant’s lap • Cargo interference with the seat • Other passengers pushing or pulling on the seat • Rear pass...

• Remove the obstruction(s) (if found). • Restart the vehicle. • Wait at least two minutes and verify that the airbag readiness light isno longer illuminated • If the airbag readiness light remains illuminated, this may or may/notbe a problem due to the front passenger sensing system. DO NOT attempt...

Seat-mounted side airbag system WARNING: Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with adeploying airbag. Failure to follow these instructions may increase therisk of personal...

WARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. WARNING: If the side airbag has deployed, the airbag will not function again.The side airbag system(including the seat) must beinspected and serviced by anauthorized dealer. If the airbag is not re...

Side curtain airbag system WARNING: Do not place objects or mount equipment on or near the headliner at thesiderail that may come intocontact with a deploying side aircurtain. Failure to follow theseinstructions may increase the riskof personal injury in the event of acollision. WARNING: Do not plac...

How does the side air curtain system work? The design and development of theside air curtain system includedrecommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the ris...

Any difficulty with the system is indicated by one or more of thefollowing: • The readiness light (same light as used for front airbag system) willeither flash or stay lit. • The readiness light will not illuminate immediately after ignition isturned to the on position. • A series of five beeps will...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) or less(generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddlerseat). Smallch...

WARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’s size,height, weight, or age. Follow the child restraint manufacturer’sinstructions and warnings provided for install...

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertified Child Passenger Safety Technician (CPST) and yourpediatrician to make sure your seat is appropriate for your child andproperly installed in the veh...

anchors is 280 mm (11 inches) center to center. A child seat with rigidLATCH attachments cannot be installed at the center seating position.LATCH compatible child seats (with attachments on belt webbing) canonly be used at this seating position provided that the child seatmanufacturer’s instructions...

child seat for information about ordering a tether strap, or to obtain alonger tether strap if the tether strap on your safety seat does not reachthe appropriate top tether anchor in the vehicle. The rear seats of your vehicle are equipped with built-in tether strapanchors located behind the seats a...

3. Open the tether anchor cover. 4. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 5. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If the ...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back be...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat build...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

• Front Wheel Drive (FWD)/AllWheel Drive (AWD) vehicles(front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalprob...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Pressure Warning Lamp will turn ON if the tire pressure issignificantly low. Once the light is illu...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2009 Fusion (fsn) Owners Guide, 2nd PrintingUSA ...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fol...

STARTING Positions of the ignition 1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessories off. 2. Accessory— allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. On— all electrical circuits ...

Starting the engine 1. Turn the key to 3 (on) withoutturning the key to 4 (start). 2. Turn the key to 4 (start), thenrelease the key as soon as theengine begins cranking. Your vehiclehas a computer assisted crankingsystem that assists in starting theengine. After releasing the key fromthe 4 (start) ...

become very hot and may result in an electrical shock or fire. Be sureto check for heat anywhere in the electrical hookup once the systemhas been operating for approximately a half hour. • Finally, have the engine block heater system checked during your falltune-up to be sure it’s in good working or...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled andthe ABS light is on, normal brakin...

When an event occurs that activates AdvanceTrac 威 you may experience the following: • A slight deceleration of the vehicle • The “sliding car” indicator light will flash. • A vibration in the pedal when your foot is on the brake pedal • If the driving condition is severe and your foot is not on the ...

The Traction Control™ switch islocated on the instrument panel.The Traction Control™ system willautomatically turn on every time theignition is turned off and on. TheTraction Control™ system shouldnormally be left on. If you should become stuck in snowor ice or on a very slippery roadsurface, try sw...

To put your vehicle in gear: • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) WARNING: Always set the parking brake fully and make sure the gearshift is l...

Do not rock the vehicle for more than a minute or damage to thetransmission and tires may occur, or the engine may overheat. MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Manual transmission vehicles have a starter interlock that preventscranking the engine unless the clutch pedal is ...

ability to anticipate wheel slip and transfer torque to the rear wheelsbefore slip occurs. The AWD system is active all the time and requires noinput from the operator.All components of the AWD system are sealed for life and require nomaintenance.If your vehicle is equipped with AWD, a spare tire of...

when you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until you regain control of the vehicle. If the engine, transmission, AWD System components or axles aresubmerged in water, their fluids should be...

Maintenance and Modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Customer Information Guidefor information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase exten...

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. The fuel pump shut-off switch islocated in the front passeng...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To red...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when...

• Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving veh...

Tire change procedure WARNING: To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side andend of the vehicle) to the tire being changed. WARNING: If the vehicle slips off the j...

7. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torquespecification. 8. Unblock the wheels. Stowing the wheel and jack 1. Fully collapse the jack and place it back in the storage area in the...

JUMP STARTING WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your aut...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing Address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing Address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

If you cannot find unleaded fuel or can only get fuel with an anti-knockindex lower than is recommended for your vehicle, contact a regionaloffice or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emi...

Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer orby writing to:Ford Motor Company of Canada, LimitedService Publications CHQ202The Canadian RoadP.O. Box 2000Oakville, ON, CanadaL6J 5E4 REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your v...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, su...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoid possible damage to the interior paintedsurfaces. • Do not use household or glass cleaners as these may damage thefinish of the instrument panel, ...

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING:...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

2. Block the wheels. WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake/Clutch fluid reservoir 5. Transmission fluid dipstick (automatic transmission only) 6. Battery 7. Power distribution box 8. Air filter assembly 9. Cool...

3.0L V6 Duratec engine 1. Engine coolant reservoir 2. Power steering fluid reservoir 3. Brake fluid reservoir 4. Transmission fluid dipstick (automatic transmission only) 5. Battery 6. Power distribution box 7. Air filter assembly 8. Coolant bleed valve 9. Engine oil dipstick 10. Engine oil filler c...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from thearm. 2. Attach the new wiper to thewiper arm and press it into placeuntil a...

• 2.3L I4 engine • 3.0L DOHC V6 Duratec engine 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. On 2.3L I4 engine, be sure thenotch in the dipstick flange isaligned with the V on the enginewhen reinserting it. 2009 Fusion (fsn) Owners Guide, 2nd PrintingUSA (fus) Maintena...

• 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must ...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal operating range, addonly certified engine oil of the recommended viscosity. Remove theengine oil filler cap and use a funnel to pour the ...

Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedulelisted in scheduled maintenance information. When changin...

It is recommended that the negative battery cable terminal bedisconnected from the battery if you plan to store your vehicle for anextended period of time. This will minimize the discharge of your batteryduring storage. Note: Electrical or electronic accessories or components added tothe vehicle by ...

3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km)...

FILL RANGE” in the coolant reservoir. If the level falls below, addcoolant per the instructions in the Adding engine coolant section. Your vehicle was factory-filled with a 50/50 engine coolant and waterconcentration. If the concentration of coolant falls below 40% or above60%, the engine parts coul...

WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hotengine parts. WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the...

7. Close the bleed valve and reinstall the cap on the coolant reservoir.Turn the cap until it is tightly installed to prevent coolant loss. After any coolant has been added, check the coolant concentration.Refer to the Checking engine coolant section. If the concentration is not 50/50 (protection to...

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequatefreeze protection at the temperatures in which you drive in thewinter months. If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentrationabo...

Continued operation will increase the engine temperature and the enginewill completely shut down, causing steering and braking effort toincrease. Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to an authorized dealer as soon as possible to minimizeengine damage. Wh...

clothing and wash skin thoroughly with soap and water. Repeated orprolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin contact cou...

• DO NOT use a device that would hold the fuel pump handle in the fillposition. Fuel filler cap Your fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise until it spins off. 3. P...

WARNING: If you do not use the proper fuel filler cap, excessive vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result inpersonal injury. Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% etha...

unleaded gasoline is not recommended for vehicles designed to use“Regular” unleaded gasoline because it may cause these problems tobecome more pronounced. If the problems persist, see your authorizeddealer.Do not add aftermarket fuel additive products to your fuel tank. Itshould not be necessary to ...

possible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel economy. We do not recommendtaking fuel economy measurements during the first 1,000 miles(1,600 km) of driving (engine break-in period). You will get a moreaccurate measurement after 2,000 miles...

3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple calculations in order to determine fueleconomy: Calculation 1: Divide total miles traveled...

• Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended...

properly (bulb is burned out), or if the OBD-II system has determinedthat some of the emission control systems have not been properlychecked. In this case, the vehicle is considered not ready for I/M testing. If the Service engine soon indicator is on or the bulb does not work, the vehicle may need ...

BRAKE/CLUTCH FLUID Brake and clutch systems are supplied from the same reservoir. The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. ...

If necessary, add fluid in 1/2 pint(250 mL) increments through thefiller tube until the level is correct. If an overfill occurs, excess fluidshould be removed by an authorizeddealer. An overfill condition oftransmission fluid may cause shift and/or engagement concernsand/or possible damage. Do not u...

Note: Only one ATF fluid specification has been tested and approved for use with the automatic 6-speed: Premium Automatic Transmission fluid.Mercon fluids cannot be used with the automatic 6-speed withoutdamage or voiding warranty. Use of a non-approved automatic transmission fluid may causeinternal...

When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter. WARNING: To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the e...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight cap...

A Accessory delay ..........................75 AdvanceTrac ..............................203 Air cleaner filter .......297–298, 300 Air conditioning ....................49, 51 Airbag supplemental restraintsystem ................136–137, 146, 149 and child safety seats ............138description .......

Passenger OccupantClassification Sensor .................124 Power distribution box(see Fuses) ...............................230 Power door locks ........................95 Power mirrors .............................76 Power point .................................73 Power steering ....................