Ford 2009 F-550 v.3- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

PERCHLORATE MATERIAL Certain components of this vehicle such as airbag modules, seat beltpretensioners, and button cell batteries may contain Perchlorate Material– Special handling may apply for service or vehicle end of life disposal.See www.dtsc.ca.gov/hazardouswaste/perchlorate. BREAKING-IN YOUR ...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. WARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions couldresult in ...

Notice to owners of pickup trucks and utility type vehicles WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this t...

If your vehicle is equipped with theFord Ambulance PreparationPackage, it will be indicated on theSafety Compliance CertificationLabel. The label is located on thedriver’s side door pillar or on therear edge of the driver’s door. Youcan determine whether theambulance manufacturer followedFord’s reco...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Vehicles equipped with a manual transmission Automatic transmission 2009 F-250/350/450/550 (f23) Owners Guide, 3rd PrintingUSA (fus) Instrument Cluster 14

Harley-Davidson vehicles Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make s...

chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic converter. Drive in a moderate fashion (avoidheavy acceleration and deceleration) and have your vehicle servicedimmediately by your authorized dealer. WARNING: Under engine misfire conditions, excessive e...

Door ajar (RTT): Displays when the ignition is in the on position andany door is open. Transmission Tow/Haul Feature(automatic transmission) (ifequipped): The Tow Haul light remains illuminated as long as theTow/Haul feature is activated. Refer to the Driving chapter for transmission function and op...

If your vehicle is equipped with a diesel engine, it has some uniquewarning lights; refer to Instrument Cluster in your 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo Diesel Owner’s GuideSupplement for detailed information on their function. Diesel warning lights: • Glow plug pre-heat • Water...

GAUGES Speedometer: Indicates the current vehicle speed. Standard instrument cluster Harley-Davidson instrumentcluster 2009 F-250/350/450/550 (f23) Owners Guide, 3rd PrintingUSA (fus) Instrument Cluster 21

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as safelypossible, switch off the engine and let the eng...

If equipped with a three button message center, press and release the message center INFO button until TRIP A or TRIP B appears in thedisplay. Press the RESET button to reset. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the t...

Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls below thenormal range, stop the vehicle, turnoff the engine and check the engineoil level. Add oil if needed. If the oillevel is correct, have your v...

Transmission fluid temperature gauge (automatic transmissiononly): If the gauge is in the: Normal area– the transmission fluid is within the normal operatingtemperature (between “H” and “C”). Yellow area– the transmission fluid is higher than normal operatingtemperature. This can be caused byspecial...

AUDIO SYSTEMSAM/FM stereo system (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is t...

SPEEDVOL (Speed sensitive volume, if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louderwith increasing vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to adjust. The default setting is off; increasing your vehicle speed will not change...

5. SEEK: In radio mode, press / to access the previous/next strong station. In CD/MP3 mode, press / to access the previous/next CD/MP3 track. In satellite radio mode (if equipped), press SEEK, SEEK to seek to the previous/next channel. If a specific category is selected,(Jazz, Rock, News, etc.), pre...

Note: In CD/MP3 mode, press SHUFFLE to play the tracks in random order. In MP3 folder mode, the system will randomly play all trackswithin the current folder. 8. FOLDER : In folder mode, press FOLDER to access next folder on MP3 discs, if available. 9. FOLDER: In folder mode, press FOLDER to access ...

To view the station name or type: When the desired category appears in the display, press TEXT/SCAN to toggle between displaying the stationtype (COUNTRY, ROCK, etc.) or the station name (WYCD, WXYZ, etc.). BASS: Press MENU to reach the bass setting. Use / / SEEK, SEEK to adjust. TREB (Treble): Pres...

If you do not choose a slot within five seconds, the system will choosefor you. Once loaded, the first track will begin to play. To auto load up to 6 discs, press and hold LOAD until the display reads AUTOLOAD#. Load the desired disc, label side up. The system willprompt you to load discs for the re...

Your vehicle may be equipped withan Auxiliary Input Jack (AIJ). TheAuxiliary Input Jack, located on theinstrument panel below the powerpoint, provides a way to connectyour portable music player to thein-vehicle audio system. This allowsthe audio from a portable musicplayer to be played through theve...

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and also to chargedevices if they support this feature.For further information on thisfeature, refer to Accessing and using your USB port in the SYNC sup...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

DVD player controls 1. Headphone control A/B: Press to select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for that headset. When aheadphone channel has been selected (A or B), selections will affect thesource on that channel only. Note: Headphone A can acces...

Remote control Unless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the player.Ensure that there are no obstructions between the remote and player. 1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF. ...

7. VOL (Volume): When in Single Play, press to increase ( ) or decrease ( ) the volume over all speakers. When in Dual Play, press to increase ( ) or decrease ( ) the volume for the wired headphones. (Wireless headphone volume is controlled with the rotary dial on theright ear piece.) 8. Fast Forwar...

21. LANGUAGE (DVD dependent): Press to select the desired language. 22. ENTER: Press to select the highlighted menu option. 23. ILLUMINATION : Press to illuminate the remote control and backlight all of the buttons. Battery replacement Batteries are supplied with the remote control unit. Since all b...

Headphones Wireless headphones WARNING: The driver should never use the headphones while driving the vehicle. Using headphones may prevent the driver from hearing audible warnings such as horns or emergency sirens,which could result in a crash causing serious injury. Give your fullattention to drivi...

Wired headphones WARNING: Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may becomeentangled in the cords and seriously injure themselves. WARNING: The driver should never use ...

LOCKED (disabled). To change the level of control, press the memorypreset controls 3 and 5 simultaneously on the front audio controls. Thecontrol level will cycle each time the buttons are pressed simultaneously.The three states are described as: FULL (enabled): The FES has control over the primary ...

MP3: Supply of this product only conveys a license for private, non-commercial use and does not convey a license nor imply any right touse this product in any commercial (i.e. revenue generating) real timebroadcasting (terrestrial, satellite, cable and /or any other media)broadcasting/streaming via ...

Do not expose the liquid crystal display (LCD) flip-down screento direct sunlight or intensive ultraviolet rays for extensiveperiods of time. Ultraviolet rays deteriorate the liquid crystal. Be sure to review User Manuals for video games and video gameequipment when used as auxiliary inputs for your...

Care and service of the DVD player Environmental extremes DVD players which are subjected to harsh environmental conditions maybe damaged or perform at less than maximum capability. To avoid theseoutcomes, whenever possible avoid exposing your DVD player to: • extremely hot or cold temperatures. • d...

Cleaning DVD and CD discs Inspect all discs for contamination before playing. If necessary, cleandiscs only with an approved DVD and CD cleaner and wipe from thecenter out to the edge. Do not use circular motion. Compatibility with aftermarket audio systems(headphone only mode) When the Family Enter...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief d...

3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the ventslocated in the middle of the instrument panel. MANUAL HEATING AND AIR CONDITIONING SYSTEMS(IF EQUIPPED) • Manual h...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle, do not drive with theair flow selector in the O (OFF) position. • Do not put objects under the front seats that will interfere...

• DATC with heated seats and heated mirrors Temperature conversion: To switch between Fahrenheit and Celsius, refer to Units (English/Metric) under either Standard Message Center or Optional Message Center in the Driver Controls chapter In order to achieve maximum cooling performance, press , A/C, ,...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle, do not drive with thesystem OFF, or with recirculated air engaged and A/C off. • Do not put objects under the front seats that...

In (panel) or (panel/floor) modes: 1. Move temperature control to full cold. 2. Select A/C and (recirculated air). Use recirculated air with A/C to provide colder airflow. 3. Set highest fan speed initially, then adjust to maintain comfort. To aid in side window defogging/demisting in cold weather: ...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableilluminated switches in the vehicleduring headlamp and parklampoperation. Move the control to the full uprightposition, past detent, to turn on theinterior lamps. Note: If the battery is disconnected, discharg...

To adjust the headlamps: 1. Park your vehicle on a levelsurface about 25 feet (7.6 meters)away from a vertical plain surface(3). Check your headlamp alignmentat night or in a dark area so thatyou can see the headlamp beampattern. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 2...

5. Locate the vertical adjuster (2)for each headlamp. Adjust the aimby turning the adjuster controleither clockwise (to adjust up) orcounterclockwise (to adjust down). 6. In addition to the horizontal linemarked in step 2, a pair of verticallines (5) must be marked at thecenter line of the headlamps...

• (4) Horizontal reference line 2. Measure the height from thecenter of your headlamp (indicatedby a 3.0 mm circle on the lens) tothe ground and mark an 8 foot(2.4 meter) horizontal reference lineon the vertical wall or screen at thisheight (a piece of masking tapeworks well). 3. Turn on the low bea...

MAP LAMPS (IF EQUIPPED) The dome lamp turns on when: • any door is opened, • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on, and • any of the remote entry controlsare pressed and the ignition isoff. BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vente...

Replacing park/turn and sidemarker lamp bulbs (aerodynamic) 1. Make sure that the headlamps are off and open the hood. 2. Remove the four bolts from thetop, side and bottom front of theheadlamp assembly. 3. Pull the assembly straight out. 4. Remove the bulb assembly, (1)sidemarker or (2) park/turn b...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is set on the intermittent settings, the speed of the wipers will automatically ...

Windshield wiper rainlamp feature (if equipped with Autolamp) When the windshield wipers are turned on during daylight, and theheadlamp control is in the autolamp position, the exterior lamps will turnon after a brief delay and will remain on until the wipers are turned off. TILT STEERING WHEEL 1. P...

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment withcassette/CD holder • Coin holder • Pen holder • Writing surface • A power point inside the utilitycompartment and on the rear ofthe console • Laptop storage • Hanging...

If your vehicle is equipped with apower rear slide window, the switchis located on the instrument panelbehind the right-hand side of thesteering wheel. • Press the right side of the controlto open the window. • Pull the right side of the controlto close the window. Accessory delay With accessory del...

With microphone The mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bright clear view whenbacking up. Do not block the sensors on the front and back of the interiorrear view mirror since this may impair proper mirrorperformance. Do not cl...

Heated outside mirrors (if equipped) The main mirror glass and lowerconvex spotter mirror are heated toremove ice, mist and fog. To activatethe heated mirrors, press the heatedmirror control located on the climate control panel. The heatedmirrors will operate for 10 minutes,then automatically shut o...

Mirror mounted side turn signal indicator (if equipped) When the vehicle turn signals areactivated, the outer portion of themirror housing will blink amber. The turn signal feature can be seenby other drivers who may approachfrom the rear of the vehicle. Clearance lamps (if equipped) Illuminates whe...

The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features when a memory position is selected through theremote entry transmitter, keyless entry keypad or memory switch on thedriver’s door (if equipped with memor...

Audio control features Press MEDIA to select: • AM, FM1, FM2 • CD (if equipped) • DVD (if equipped) • SAT1, SAT2 or SAT3 (SatelliteRadio mode, if equipped). • LINE IN (Auxiliary input jack) In AM, FM1, or FM2 mode: • Press SEEK to select preset stations within theselected radio band or press andhold...

Navigation system hands freecontrol features (if equipped) Press and hold VOICE briefly untilthe voice icon appears on the Navigation display to use the voicecommand feature. Press VOICE to complete a voicecommand. For further information on theNavigation system, refer to the Navigation System suppl...

There will also be one power leadfor each switch found as a blunt-cutand sealed wire located below theinstrument panel and to the left ofthe steering column. They are coded as follows: Switch Circuit number Wire color Fuse AUX 1 CAC05 Yellow 30A AUX 2 CAC06 Green withBrown Trace 30A AUX 3 CAC07 Viol...

Do not use the HomeLink 威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required byU.S. federal safety standards (this includes any garage door openermodel manufactured before April 1, 1982). A garage door which cannotdetect an object, signaling t...

• If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with “Programming” Steps 4 through6 to complete programming of a rolling code equipped device (most commonly a garage door opener). 4. At the garage door opener receiver (motor-head unit) in the garag...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

STANDARD MESSAGE CENTER (IF EQUIPPED) With the ignition in the on position,the message center, located on yourinstrument cluster, displays textmessages that alert you to possibleproblems or malfunctions in yourvehicle’s operating systems. Allwarning messages will also providean indicator chime. For ...

DRAIN WATER SEPARATOR (Diesel engine only) — Displayed when the water separator has reached a predetermined capacity andneeds to be drained. Refer to your 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for more information. STOP SAFELY NOW (Diesel engine only) ...

OPTIONAL MESSAGE CENTER (IF EQUIPPED) With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the messagecenter for a display of status. Thesyste...

5. AIR FILTER (Diesel engine only) 6. DOOR AJAR 7. BRAKE SYSTEM 8. TBC GAIN = XX.XNO TRAILER (if equipped and no trailer connected) 9. TBC GAIN = XX.XOUTPUT = ////// (if equipped and trailer connected) 10. FUEL LEVEL Oil Life XXX% HOLD RESET = NEW An oil change is required whenever indicated by the ...

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with atailgate lock designed to helpprevent theft of the tailgate. • Insert ignition key and turn to theright to engage lock. • Turn ignition key to the left tounlock. Tailgate removal Your tailgate is removable to allow more room for loading....

2. Open the latches to release thepanels. 3. Rotate the panels toward thetailgate. Repeat Steps 1–3 for the other side of the bed extender. 4. Connect the two panels, then rotate both knobs a quarter-turnclockwise to secure the panels. 2009 F-250/350/450/550 (f23) Owners Guide, 3rd PrintingUSA (fus)...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency. If your vehicle is equipped with the SecuriLock™ Passive Anti-theftsystem, your keys are electronically coded to your vehicle; using anon-coded key wil...

5. Turn the ignition back to the on position. The horn will chirp one timeto confirm programming mode has been entered and is active. 6. To enable/disable the autolock feature, press the unlock control, thenpress the lock control. The horn will chirp once if autolock wasdeactivated or twice (one sho...

The typical operating range for your remote entry transmitter isapproximately 33 feet (10 meters). A decrease in operating range couldbe caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. Your vehicle is equipped ...

Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and one step door unlocking by pressing andholding both the and buttons simultaneously on the remote entry transmitter for approximately four seconds. The ...

Activating the memory feature To activate this feature: 1. Position the seat, adjustable pedals and mirrors to the positiondesired. 2. Press and hold either memory 1button or memory 2 button for fiveseconds. A tone will be heard after1 1 ⁄ 2 seconds when the memory store is done, continue to hold un...

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing oftransmitter batteries. 4. Insert the new battery. Refer tothe diagram inside the remote entrytransmitter for the correcto...

To reprogram the remote entrytransmitters: 1. Ensure the vehicle iselectronically unlocked. 2. Put the key in the ignition. 3. Cycle eight times rapidly (within10 seconds) between the offposition and on. Note: The eighth turn must end in the on position. The doors will lock,then unlock, to confirm t...

Deactivating/activating perimeter lamps illuminated entry You may enable/disable this feature by having your vehicle serviced byyour authorized dealer. You may also perform the following power door lock sequence toenable/disable the perimeter lamps feature. Note: Before starting, ensure the ignition...

5. The doors will again lock then unlock to confirm that your personalkeycode has been programmed to the module. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personalcode. Er...

SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock™ passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent the engine from beingstarted unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to ...

Vehicles without the SecuriLock™ Passive Anti-theft system behave asfollows: • When the ignition is in the off position, the indicator will not flash. • When the ignition is in the on position, the indicator will glow forthree seconds to indicate the engine is enabled. Automatic arming The vehicle i...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of anunauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL remote entry transmitters are taken to the authorized dealer to aid in troubles...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

Captain’s chair (if equipped) • Lift the bar to move the seatforward or rearward. Make surethat the seat is relatched intoplace. • To recline the seatback, pull therelease lever handle located onthe side of the seat up. • Push down the lever (ifequipped) located at the bottomof the seatback to quick...

Press front to raise or lower thefront portion of the seat cushion. Press rear to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Using the manual lumbar support The lumbar support control islocated on the outboard side of theseat ...

Heated seats (if equipped) The heated seat control is located on the climate control panel. WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physicalconditions, must exercise...

To recall a memory position: • Press and release either memory 1 button or memory 2 button. A position can be recalled: • in any gearshift position if the ignition is not in the on position. • only in P (Park) or N (Neutral) if the ignition is in the on position. A memory seat position may be progra...

Push control to lower head restraint. WARNING: To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in itsproper position. The driver should never adjust the head restraintwhil...

To flip the seat cushion up, pull up on the lever located on the sideof the seat cushion to rotate thecushion up until it locks into avertical storage position, gainingaccess to the grocery hook locatedon the underside of the driver-sideseat cushion. The maximum load is25 lb. (11 kg). Returning the ...

WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belton the outside shoulder only. Never wear the shoulder belt under thearm. 2) Never swing the safety belt aro...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. Vehicle sensitive mode Combination lap and shoulder belts in normal retractor mode allow freeshoulder belt length adjustment to your movements and locking inresponse to vehicle movement. For example, if the driver brakessud...

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operatingproperly when checked by an authorized dealer. Failure to replace thebelt and retractor assembly could increase the risk of injury...

How to fasten the cinch tongue (Regular cab center seatingposition and Super Cab/Crew Cab rear center seating positions) 1. Pull the combination lap and shoulder belt from the retractor so thatthe shoulder belt portion of the safety belt crosses your shoulder andchest. 2. Be sure the belt is not twi...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

WARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s air bagsystem. One-time disable Any time the safety belt is buckled and then unbuckled during anignition on cycl...

• Step 3 must be completed within 60 seconds after the safety beltwarning light turns off. 3. At a moderate speed, buckle then unbuckle the safety belt 9 times,ending with the safety belt in the unbuckled state. • After Step 3 is complete, the safety belt warning light will be turnedon for 3 seconds...

WARNING: Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly...

Children and airbags For additional important safety information, read all information onsafety restraints in this guide. Children must always be properly restrained. Failure to follow theseinstructions may increase the risk of injury in a collision. WARNING: An infant in a rear-facing seat faces a ...

The diagnostic module monitors its own internal circuits and thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness light, the airbagback up power and the airbag ignitors. Determining if the system is operational The SRS uses a r...

WARNING: If your vehicle has rear seats, always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly. DO NOT place a child in arear facing infant seat in the front seat unless your vehicle is equippedwith an airbag ON/OFF switch and the pa...

• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can constantly monitor the child’s condition. 3. Medical condition. A passenger has a medical condition which, according to his or her physician:...

• the child has a medical condition that, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can monitor the child’s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a sp...

WARNING: All children are shaped differently. The Recommendations for Safety Restraints are based on probable child height, age and weight thresholds from NHTSA and other safetyorganizations or are the minimum requirements of law. Fordrecommends checking with a NHTSA Certified Child Passenger Safety...

• You are required by law to properly use safety seats for infants andtoddlers in the U.S. and Canada. • Many states and provinces require that small children use approvedbooster seats until they reach age eight, a height of 4 ft 9 in(1.45 meters) tall, or 80 lb (36 kg). Check your local and state o...

WARNING: Do not leave children, unreliable adults, or pets unattended in your vehicle. Transporting children Always make sure your child is secured properly in a device that isappropriate for their age, height and weight. All children are shapeddifferently. The child height, age and weight threshold...

Tether strap attachment 1. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, other wise routethe tether strap over the top of the seatback. If the top ...

Tether strap attachment (rear SuperCab only) There are three loops of webbing just above the back of the rear seat(along the bottom edge of the rear window) in the SuperCab. Theseloops are to be used as both routing loops and anchor loops for up tothree child safety seat tether straps. These straps ...

3. Install the child safety seat tightlyusing the vehicle belts. Follow theinstructions in this chapter. 4. Tighten the tether strapaccording to the child seatmanufacturer’s instructions. A single loop can be used to route and anchor more than one child seat.For example, the center loop can be used ...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Move a child to a different seating location if the shoulder belt does notstay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back be...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. Information on transfer case operation and shifting procedurescan be found in the Driving chapter. Information on transfer case maintenance can be f...

Treadwear The treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernment test course. For example, a tire graded 150 would wear oneand one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The ...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

under-inflation of the tires, improper tires (load range, size, or type), orvehicle modifications such as lift-kits. In the event that your vehicleexperiences shimmy, you should slowly reduce speed by either lifting offthe accelerator pedal or lightly applying the brakes. The shimmy willcease as the...

Note: Some spare tires operate at a higher inflation pressure than the other tires. For T-type/mini-spare tires (see the Dissimilar spare tire/wheel information section for description): Store and maintain at 60 psi (4.15 bar). For Full Size and Dissimilar spare tires (see the Dissimilar spare tire/...

WARNING: Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that may be wedged in thetread grooves. Check for holes or cuts that may permit...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a p...

Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly, providing better tire performance andlonger tire life. • Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All ...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Warning Lamp will turn ON if the tire pressure is significantly low.Once the light is illuminated, ...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Please refer to thefollowing chart for information conc...

Low TirePressureWarningLight Possible cause Customer Action Required FlashingWarningLight Spare tire in use Your temporary spare tire is in use.Repair the damaged road wheel andre-mount it on the vehicle to restoresystem functionality. For adescription of how the systemfunctions under these conditio...

TPMS reset procedure (if applicable) The TPMS reset tool is ONLY provided for vehicles with differentfront and rear tire pressures. The TPMS reset procedure needs tobe performed after tire rotation only on these vehicles. WARNING: To determine if your vehicle has different recommended pressures for ...

Storing the TPMS reset tool You should store the TPMS resettool in the provided pocket of theowner guide case; however, beforestoring it, you will need to removeand discard the loose strip ofVelcro 威 (this is the piece of Velcro 威 with the adhesive protection film onit); you will not need this porti...

and remain on for approximately five (5) seconds. If the light does notilluminate, the tool needs to be replaced. TPMS reset tips: • To reduce the chances of interference from another vehicle, TPMSreset should be performed at least three feet (one meter) away fromanother Ford Motor Company vehicle u...

7. Train the TPMS sensors in the tires using the following TPMS resetsequence starting with the left front tire in the following clockwise order: 1. Left front tire (Front driver’s side) 2. Right front tire (Front passenger’s side) 3. Right rear tire (Rear passenger’s side) 4. Left rear tire (Rear d...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment,passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or theedge of the driver’s door. The GVW must never exceed ...

safe control of towed vehicles and for trailers where the GCW of thetowing vehicle plus the trailer exceed the GVWR of the towing vehicle. The GCW must never exceed the GCWR. Maximum Loaded Trailer Weight – is the highest possible weight of a fully loaded trailer the vehicle can tow. It assumes a ve...

The above calculations also assume that the loads are positioned in yourvehicle in a manner that does not overload the Front or the Rear GrossAxle Weight Rating specified for your vehicle on the Safety ComplianceCertification Label found on the edge of the driver’s door. Special loading instructions...

Maximum GCWR - lb. (kg.) Engine Rear axle ratio Manual transmission Automatic transmission F–350 Dual Rear Wheel (DRW) Pick-up 5.4L 4.10 17500 (7938) 18500 (8391) 6.8L 4.10 20500 (9299) 21500 (9752) 4.30 22500 (10206) 23000 (10433) F–350 Single Rear Wheel (SRW) Chassis Cab 5.4L 3.73 15000 (6804) 160...

Hitch rating The standard hitch has two ratings depending on mode of operation: • Weight carrying - requires a draw bar and hitch ball. The draw bar supports all the vertical tongue load of the trailer. • Weight distributing - requires an aftermarket weight distributing system which includes draw ba...

2. Measure the height of a reference point on the front and rear bumpersat the center of the vehicle. 3. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within 1 ⁄ 2 inch (13 mm) of the reference point. After proper adjustment, the rear bumper shou...

• TRAILER DISCONNECTED: This message is displayed and accompanied by a single chime, when a trailer connection wasdetermined and then a disconnection, either intentionally orunintentionally, has been sensed during a given ignition cycle. It is alsodisplayed if a truck or trailer wiring fault occurs ...

5. In a traffic-free environment, tow the trailer on a dry, level surface ata speed of 20–25 mph (30–40 km/h) and squeeze the manual controllever completely. 6. If the trailer wheels lock-up (indicated by squealing tires), reduce theGAIN setting; if the trailer wheels turn freely, increase the GAIN ...

• Avoid towing in adverse weather conditions. The TBC does notprovide anti-lock control of the trailer wheels. Trailer wheels canlock-up on slippery surfaces, resulting in reduced stability of trailerand tow vehicle. • The TBC interacts with the brake system of the vehicle, includingABS, in order to...

type (All-Season or All-Terrain) or is from a different manufacturerother than the road tires on your vehicle, your spare tire is considered“temporary”. Consult information on the spare Tire Label or SafetyCompliance Certification Label for limitations when using. Servicing after towing If you tow a...

• The load distribution within the trailer should be such that 10%–15%of the trailer weight is on the hitch. (15%–25% for fifth-wheel orgooseneck towing.) • Never exceed truck, trailer, receiver, ball, tongue, tire or couplerloading recommendations. Braking • The trailer brakes must be inspected and...

Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability, emissions and reliability. Replace the rear axle lubricant any time the axle has been submerged inwater. Rear axle lubricant quantities are not to be checked or ...

STARTING Positions of the ignition 1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal. 2. Accessory— allows the electricalaccessories such as the radio tooperate while the engine is notrunning. This position also unlocksthe steering wheel. 3. On— all elect...

WARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. Ifthe engine idle speed does not slow down automatica...

How to Use the Engine Block Heater Ensure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth. Depending on the type of factory installed equipment, your engine blockheater system may consume anywhere between 400 watts or 1000 wattsof power per hour. Your factory i...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. If...

into four-wheel drive mode (if equipped), the traction control system willbe automatically disabled. Traction control operation will resume whenthe vehicle is placed back into two-wheel drive mode. WARNING: Aggressive driving in any road conditions can cause you to lose control of your vehicle incre...

• Do not fill the power steering pump reservoir above the MAX mark onthe reservoir, as this may result in leaks from the reservoir. If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls...

WARNING: Vehicles with a higher center of gravity such as utility vehicles and trucks handle differently than vehicles with a lower center of gravity. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slungsports cars are designed to per...

3 (Third) Transmission starts and operates in third gear only. Used for improved traction on slippery roads. Selecting 3 (Third)provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additionalengine braking on downgrades. 1 (First) • Provides maximum engine b...

Using the clutch Manual transmission vehicles have a starter interlock that preventscranking the engine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral po...

Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Fully apply the parking brake, then shift into 1 (First). 3. Turn the ignition off. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake ...

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system,located on the tailgate, provides avideo image, which a...

WARNING: Do not use the camera system with the tailgate open. If the back end of the vehicle is hit or damaged, then check with yourauthorized dealer to have your rear video system checked for propercoverage and operation. Night time and dark area use At night time or in dark areas, the camera syste...

The 4WD system: • provides 4x4 High engagement and disengagement while the vehicle ismoving. • is operated by a rotary control located on the instrument panel thatallows you select 2WD, 4x4 High or 4x4 Low operation. • uses auto-manual hub locks that can be engaged and disengagedautomatically based ...

Shifting from 4H (4x4 High) to 2H (2WD) Move the transfer case lever to 2H(2WD) at a stop or a vehicle speedbelow 5 mph (8 km/h). With the vehicle at complete stop,disengage the locking hubs(optional) by rotating the hub lockcontrol from LOCK to FREE. • For proper operation, makesure that both indic...

5. If shifting to 2H (2WD) with the vehicle at a complete stop, disengagethe locking hubs (optional) by rotating the hub lock control from LOCKto FREE. Using the N (Neutral) position The transfer case neutral position overrides the transmission andputs the vehicle in neutral regardless of transmissi...

Shifting from 2WD to 4x4 HIGH Rotate the 4x4 control to the 4x4HIGH position at speeds up to55 mph (88 km/h). • The electronic shift 4x4system is designed to engage4x4 HIGH when the vehicle ismoving. If shifted to 4x4HIGH while at complete stop,4x4 may not engage and the4x4 indicator may flashcontin...

3. Move the 4x4 control to the 4x4LOW position. 4. Hold the shift conditions until the4x4 LOW indicator light illuminates. 5. If the 4x4 LOW indicator lightflashes continuously for more than10 seconds, allow the vehicle tomove at a speed below 5 mph(8 km/h), then repeat steps 2through 5 while the ve...

sideways out of control or roll over. Remember, your safety and thesafety of others should be your primary concern. WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel ...

WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drivevehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars...

Driving through deep water may damage the transmission. Refer to Transmission temperature gauge in the Instrument Cluster chapter for transmission fluid temperature information. If the front or rear axle is submerged in water, the axle lubricant shouldbe replaced. After driving through mud, clean of...

When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This reduces strain on theengine and the possibility of stalling. If you do stall out, do not try toturn around because you might rollover. It is better to ...

VEHICLE USED AS A STATIONARY POWER SOURCE Auxiliary equipment called power take-off, or PTO, is often added to theengine or transmission to operate utility equipment. Examples include awheel-lift for tow trucks, cranes, tools for construction or tire service,and pumping fluids. PTO applications draw...

SNOWPLOWING Ford recommends that the Super Duty F-Series used for snow removalinclude the Snow Plow Package Option. Installing the snowplow Weight limits and guidelines for selecting and installing the snowplow canbe found in the Ford Truck Body Builders Layout Book, Snowplow section, found at www.f...

• The snow plow prep package includes a unique powertrain controlstrategy which is required for diesel engine cooling during highwaydriving with the snowplow raised. Operating the vehicle with the snowplow attached Do not use your vehicle for snow removal until it has been driven atleast 500 miles (...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. This switch is located on thepassenger’s side of the instrum...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located in thepassenger’s footwell. Remove thepanel cover to access the fuses. To remove the fuse panel cover, pullthe panel toward you. When theclips of the panel disengage, let thepanel fall easily. To remove a fuse use the fuse pullertool provide...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Not used (spare) 2 15A Not used (spare) 3 15A Family Entertainment System (FES) 4 30A Not used (spare) 5 10A Keypad illumination, Brake-ShiftInterlock (BSI), SPBJB 6 20A Turn signals 7 10A Left headlamp (Low...

CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily. • gradually decrease the vehicle’s speed. • hold the steering wheel firmly. • slowly move to a safe place on the side of the road. Your vehicle may be equipped with a conventional spare tire that isdifferent in one or...

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (...

• Tow a trailer • Use snow chains on the end of the vehicle with the temporary sparetire • Use more than one temporary spare tire at a time Use of a temporary spare tire at any one wheel location can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and nois...

Location of the spare tire and tools If your vehicle is equipped with a spare tire, jack and associated tools,refer to the following table for their locations: Tool Location Spare tire (pick-up trucks only) Under the vehicle, just forward ofthe rear bumper Jack Regular cab and Crew Cab:Fastened to f...

• Vehicles equipped with dualrear wheels, insert the lug wrench extension into the lugwrench to reach the lug nuts. 2. Attach the spare tire lock key (A)to the jack handle (B). 3. Fully insert the jack handle (withone extension) through the bumperhole and into the guide tube. Thekey and lock will en...

WARNING: To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side andend of the vehicle) to the tire being changed. WARNING: If the vehicle slips off the jack, you or someone else co...

13. Insert the jack handle into thepump linkage. 14. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground. Hydraulic jacks are equippedwith a pressure release valvethat prevents lifting loads whichexceed the jack’s rated capacity. 15. Remove the lug nuts with the...

10–lug nut torque sequence 19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicle is equipped with a spare tire carrier. Note: Do not stow the Harley-Davidson flat tire and wheel using the spare tire winch mechanism; store the flat in the bed of the truck. 20. Stow the jack, jac...

If the ornament retention towers arealigned between the studs/lug nuts,the ornament is improperlyinstalled. This improper installationmay appear and sound correct, butwill not keep the ornament on thevehicle. Ornaments improperlyinstalled in this manner will fall offor become loose with minimal forc...

5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, per scheduled maintenance information), or at any time that the spare tire is disturbed through service of othercomponents. 6. If removed, install the spare tire lock (if equipped) into the bumperdrive ...

Inspect the wheel pilot hole prior toinstallation. If there is visiblecorrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot surface (1...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect t...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that the vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbe...

Note: Towing an ESOF 4x4 vehicle with the front wheels on the ground without disengaging the front hubs may cause damage to the automatictransmission. Note: Towing a 4x2 or an ESOF 4x4 vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph(56 km/h) may c...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

If you cannot find unleaded fuel or can only get fuel with an anti-knockindex lower than is recommended for your vehicle, contact a regionaloffice or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emi...

Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer orby writing to:Ford Motor Company of Canada, LimitedService Publications CHQ202The Canadian RoadP.O. Box 2000Oakville, ON, CanadaL6J 5E4 REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your v...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent quality product to help protect from environmentaleffects. WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Pr...

• 6.8L V10 gasoline engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRem...

INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area firstwith Mo...

LEATHER SEATS FOR THE KING RANCH F-250 AND F-350 CREWCAB ONLY (IF EQUIPPED) Your vehicle is equipped with seating covered in premium, top-grainleather which is extremely durable, but still requires special care andmaintenance in order to ensure longevity and comfort. Regular cleaning and conditionin...

Conditioning Bottles of King Ranch Leather Conditioner are available at the KingRanch Saddle Shop. Visit the Web site at www.krsaddleshop.com , or telephone (in the United States) 1–800–282–KING (5464). If you areunable to obtain King Ranch Leather Conditioner, use another premiumleather conditioner...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

2. Block the wheels. WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left c...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Refer to the 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 5.4L V8 gasoline engines 1. Windshield washer fluid reservoir 2. Battery 3. Transmission fluid dipstick (automati...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from thearm. 2. Attach the new wiper to thewiper arm and press it into placeuntil a...

• 5.4L/6.8L gasoline engines only;for diesel engine information,refer to the 6.0 and 6.4 Liter Direct Injection Turbo DieselOwner’s Guide Supplement. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acc...

4. Install the dipstick and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise1/4 of a turn until three clicks are heard or until the cap is fully seated. To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level dipstick a...

It is recommended you use the appropriate Motorcraft oil filter oranother with equivalent performance for your engine application. BATTERY WARNING: This vehicle may be equipped with more than one battery, removal of cablefrom only one battery does notdisconnect the vehicle electricalsystem. Be sure ...

WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle orbattery. Lift the battery with a battery carrier or with your hands onopposite corners. WARNING: Keep batteri...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

• Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer to Maintenance product specifications and capacities in this chapter. Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, ...

Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposi...

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cool...

When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high-speedoperation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to pre...

• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin contact could cause an adverse reaction. In sensitiveindividuals, serious personal injury or sickness may result. If fuel issplashed on the skin, prom...

Fuel filler cap When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise until it spins off. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on thefiller pipe. 5. Turn the filler cap cl...

Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol, leadedfuel or any other fuel. The use of leaded fuel is prohibited by law andcould damage your vehicle. Your vehicle was not designed to use fuel or ...

Many of the world’s automakers approved the World-Wide Fuel Charterthat recommends gasoline specifications to provide improvedperformance and emission control system protection for your vehicle.Gasolines that meet the World-Wide Fuel Charter should be used whenavailable. Ask your fuel supplier about...

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel ga...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended engine oil. Refer to Maintenance product specifications and capacities in this chapter. • Perform all regularly scheduled mainte...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

POWER STEERING FLUID Check the power steering fluid. Refer to scheduled maintenance information. If adding fluid is necessary, use only MERCON 威 ATF. • Gasoline engine shown; dieselengine similar. Refer to Identifying components in theengine compartment in the 6.0 and 6.4 Liter Power StrokeDirect In...

BRAKE FLUID • Vacuum boost system • Hydroboost system The fluid level will drop slowly as the brakes wear, and will rise when thebrake components are replaced. Fluid levels between the “MIN” and“MAX” lines are within the normal operating range; there is no need toadd fluid. If the fluid levels are o...

CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to scheduled maintenance information for the service interval schedules. During normal operation, the fluid level in the clutch reservoir shouldremain constant. If the fluid level drops, refill the fluid level to the stepin the reservoir. Use o...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at thebottom of the opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. I...

AIR FILTER Refer to the scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter. The following procedure is for vehicl...

2. Release three retainer clamps. 3. Pull air filter cover toward passenger side of vehicle and up to releasethe tabs. Lift air filter element up and out of housing. The air filter box needs to be free of any debris before installing a newair filter. 4. Install a new air filter element into the tray...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ........................110 Air cleaner filter ...............402, 404 Air conditioning ..........................84 Airbag supplemental restraintsystem ........................................193 and child safety seats ............195description ..............................193di...

recommendations ...................374refill capacities ........................405 Event data recording ....................7 Exhaust fumes ..........................278 F Fail safe cooling ........................382 Family entertainment system ....51 Fluid capacities .........................405 ...

Pedals (see Power adjustablefoot pedals) ...............................115 Power adjustable foot pedals ...115 Power distribution box(see Fuses) ...............................322 Power door locks ......................155 Power mirrors ...........................111 Power point ......................