Ford 2009 F-250 - Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

Vehicle Modification Data Recording Some aftermarket products may cause severe engine and/or transmissiondamage; refer to the What is not covered section in The new vehicle limited warranty for your vehicle chapter of your vehicle’s Warranty Guide for more information. Some vehicles are equipped wit...

Cell phone use The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

Using your vehicle with a snowplow For more information and guidelines for using your vehicle with asnowplow, refer to the Driving chapter. Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance PreparationPackage, it may be utilized as an ambulance. Ford urges am...

Using your vehicle as a stationary power source (PTO) Refer to the Driving chapter for more information and guidelines for operating a vehicle equipped with an aftermarket power take-off system. Export unique (Non–United States/Canada) vehicle specificinformation For your particular global region, y...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Vehicles equipped with a manual transmission Vehicles equipped with an automatic transmission 2009 F-250/350/450/550 (f23) Owners Guide, 2nd PrintingUSA (fus) Instrument Cluster 14

Harley-Davidson vehicles Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make s...

chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic converter. Drive in a moderate fashion (avoidheavy acceleration and deceleration) and have your vehicle servicedimmediately by your authorized dealer. WARNING: Under engine misfire conditions, excessive e...

Transmission Tow/Haul Feature(automatic transmission)(if equipped): The Tow Haul light remains illuminated as long as theTow/Haul feature is activated. Refer to the Driving chapter for transmission function and operation. If the light remains illuminated andwill not cancel using the Tow/Haul switch ...

GAUGES Speedometer: Indicates the current vehicle speed. Standard instrument cluster Harley-Davidson instrumentcluster 2009 F-250/350/450/550 (f23) Owners Guide, 2nd PrintingUSA (fus) Instrument Cluster 21

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as safelypossible, switch off the engine and let the eng...

Standard instrument cluster Harley-Davidson instrumentcluster Engine hour meter(if equipped): Registers the accumulated time the engine hasbeen running. Press and release themessage center INFO button untilthis is displayed. Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should ...

Fuel gauge: Indicates approximately how much fuel is leftin the fuel tank (when the ignitionis in the on position). The fuelgauge may vary slightly when thevehicle is in motion or on a grade.The FUEL icon and arrow indicateswhich side of the vehicle the fuelfiller door is located. Refer to Filling t...

Yellow area (warning) — the transmission fluid is higher thannormal operating temperature. Thiscan be caused by special operationconditions (i.e. snowplowing, towingor off road use). Refer to Special Operating Conditions in the scheduled maintenanceinformation for instructions. Operating the transmi...

AUDIO SYSTEMSAM/FM stereo system (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. The driver’s primary responsibility is t...

In satellite radio mode (if equipped) , press / to tune to the next/previous channel. Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability. 2. (Phone): If your vehicle is equipped with SYNC, press toaccess SYNC PHONE features. Fo...

FADE: Press MENU to reach the fade setting. Use / / SEEK, SEEK to adjust the audio between the back (B) and front (F) speakers. SPEEDVOL (Speed sensitive volume, if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louderwith increasing vehicle speed to compensate ...

5. SEEK: In radio mode, press / to access the previous/next strong station. In CD/MP3 mode, press / to access the previous/next CD/MP3 track. In satellite radio mode (if equipped), press SEEK, SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.), pr...

In satellite radio mode (if equipped), press and hold to hear a brief sampling of the next channels. Press again to stop. In CATEGORYMODE, press SCAN to hear a brief sampling of the channels in theselected category. Press again to stop. Satellite radio is available only with a valid SIRIUS radiosubs...

To view the station name or type: When the desired category appears in the display, press TEXT/SCAN to toggle between displaying the stationtype (COUNTRY, ROCK, etc.) or the station name (WYCD, WXYZ, etc.). BASS: Press MENU to reach the bass setting. Use / / SEEK, SEEK to adjust. TREB (Treble): Pres...

7. SHUFFLE: In CD/MP3 mode, press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engage shuffle mode right away, press SEEKto begin random play. Otherwise, random play will begin when thecurrent track is finished playing. CD SHUF will appear in the display. Todis...

To auto load up to 6 discs, press and hold LOAD until the display reads AUTOLOAD#. Load the desired disc, label side up. The system willprompt you to load discs for the remaining available slots. Insert thediscs, one at a time, label side up, when prompted. Once loaded, the discin the last slot load...

Your vehicle may be equipped withan Auxiliary Input Jack (AIJ). TheAuxiliary Input Jack, located on theinstrument panel below the powerpoint, provides a way to connectyour portable music player to thein-vehicle audio system. This allowsthe audio from a portable musicplayer to be played through theve...

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and also to chargedevices if they support this feature.For further information on thisfeature, refer to Accessing and using your USB port in the SYNC sup...

Audio system warranty and service Refer to the Warranty Guide/Customer Information Guide for audio system warranty information. If service is necessary, see your dealer orqualified technician. MP3 track and folder structure Your MP3 system recognizes MP3 individual tracks and folder structureas foll...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and play a variety of standard video game systems. TheDVD player is capable of playing standard DVDs, CDs, MP3s and iscompatible with CD-R/W, CD-R and cer...

DVD player controls 1. Headphone control A/B: Press to select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for that headset. When aheadphone channel has been selected (A or B), selections will affect thesource on that channel only. Note: Headphone A can acces...

press the 2 and 4 memory preset buttons on the audio system at thesame time to perform the same function. For further interactioninformation, refer to Single Play/Dual play under Operation later in this section. 12. MEDIA: Press repeatedly to select from the various possibleplaying media sources (AM...

1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF. 2. Cursor controls: Use in various active menus to advance the cursor up/down/left/right. When not in a Menu, the left and right cursor controlsdecrease and increase the display brightness. 3. DISPLAY: Press to access the ...

Battery replacement Batteries are supplied with the remote control unit. Since all batterieshave a limited shelf life, replace them when the unit fails to control theDVD player. Remove the screw and unlatch the battery cover to access the batteries. The remote control unit uses two AAA batteries whi...

Headphones Wireless headphones WARNING: The driver should never use the headphones while driving the vehicle. Using headphones may prevent the driver from hearing audible warnings such as horns or emergency sirens,which could result in a crash causing serious injury. Give your fullattention to drivi...

Wired headphones WARNING: Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may becomeentangled in the cords and seriously injure themselves. WARNING: The driver should never use ...

• : Press to play a DVD or to pause the DVD. When the radio displays “DVD MENU”, press PLAY on the radio(memory preset #6), to play the disc. Parental control for the DVD system Your Family Entertainment System (FES) allows you to have controlover the rear seat controls in a few different ways. The ...

General information Note: DVDs are formatted by regions. US and Canada systems canonly play region 1 DVDs and Mexicosystems can only play region 4DVDs. Systems sold in vehiclestargeted for other parts of the worldwould have different regions. If aplayback problem is encountered,please ensure that yo...

Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Lincoln-Mercury could voiduser’s authority to operate the equipment. This equipment has been testedand found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. Th...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief d...

3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents towards the side windows.To increase airflow to the outer instrument panel vents, close the ventslocated in the middle of the instrument panel. MANUAL HEATING AND AIR CONDITIONING SYSTEMS(IF EQUIPPED) • Manual he...

2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the instrument panel vents only to ...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle, do not drive with theair flow selector in the O (OFF) position. • Do not put objects under the front seats that will interfere...

• DATC with heated seats and heated mirrors Temperature conversion: To switch between Fahrenheit and Celsius, refer to Units (English/Metric) under either Standard Message Center or Optional Message Center in the Driver Controls chapter In order to achieve maximum cooling performance, press , A/C, ,...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle, do not drive with thesystem OFF, or with recirculated air engaged and A/C off. • Do not put objects under the front seats that...

In (panel) or (panel/floor) modes: 1. Move temperature control to full cold. 2. Select A/C and (recirculated air). Use recirculated air with A/C to provide colder airflow. 3. Set highest fan speed initially, then adjust to maintain comfort. To aid in side window defogging/demisting in cold weather: ...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableilluminated switches in the vehicleduring headlamp and parklampoperation. Move the control to the full uprightposition, past detent, to turn on theinterior lamps. Note: If the battery is disconnected, discharg...

To adjust the headlamps: 1. Park your vehicle on a levelsurface about 25 feet (7.6 meters)away from a vertical plain surface(3). Check your headlamp alignmentat night or in a dark area so thatyou can see the headlamp beampattern. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 2...

5. Locate the vertical adjuster (2)for each headlamp. Adjust the aimby turning the adjuster controleither clockwise (to adjust up) orcounterclockwise (to adjust down). 6. In addition to the horizontal linemarked in step 2, a pair of verticallines (5) must be marked at thecenter line of the headlamps...

• (4) Horizontal reference line 2. Measure the height from thecenter of your headlamp (indicatedby a 3.0 mm circle on the lens) tothe ground and mark an 8 foot(2.4 meter) horizontal reference lineon the vertical wall or screen at thisheight (a piece of masking tapeworks well). 3. Turn on the low bea...

MAP LAMPS (IF EQUIPPED) The dome lamp turns on when: • any door is opened, • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on, and • any of the remote entry controlsare pressed and the ignition isoff. BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vente...

2. Remove the three screws and onebolt from the top and bottom of thepark lamp/bezel assembly. 3. Remove the four screws and theheadlamp retaining ring fromheadlamp. 4. Disconnect the electricalconnector from the headlamp. Install the new bulb(s) in reverse order. Replacing park/turn/sidemarker bulb...

4. Remove the bulb assembly,sidemarker or park/turn by turningit counterclockwise. (Top view ofassembly shown.) 5. Pull the old bulb out from thesocket. Install the new bulb(s) in reverse order. Replacing brake/tail/turn/back-up lamp bulbs - Pick-ups only 1. Make sure the headlamps are offand then o...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is set on the intermittent settings, the speed of the wipers will automatically ...

TILT STEERING WHEEL 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering up or downuntil you find the desired location. 3. Release the steering wheelrelease control. This will lock thesteering wheel in position. WARNING: Never adjust the steering column when the vehicl...

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment withcassette/CD holder • Coin holder • Pen holder • Writing surface • A power point inside the utilitycompartment and on the rear ofthe console • Laptop storage • Hanging...

Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (to the first detent) andhold the switch to close. Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or bu...

Without microphone With microphone The mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bright clear view whenbacking up. Do not block the sensors on the front and back of the interiorrear view mirror since this may impair proper mirrorper...

Heated outside mirrors (if equipped) The main mirror glass and lowerconvex spotter mirror are heated toremove ice, mist and fog. To activatethe heated mirrors, press the heatedmirror control located on the climate control panel. The heatedmirrors will operate for 10 minutes,then automatically shut o...

Mirror mounted side turn signal indicator (if equipped) When the vehicle turn signals areactivated, the outer portion of themirror housing will blink amber. The turn signal feature can be seenby other drivers who may approachfrom the rear of the vehicle. Clearance lamps (if equipped) Illuminates whe...

The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features when a memory position is selected through theremote entry transmitter, keyless entry keypad or memory switch on thedriver’s door (if equipped with memor...

Audio control features Press MEDIA to select: • AM, FM1, FM2 • CD (if equipped) • DVD (if equipped) • SAT1, SAT2 or SAT3 (SatelliteRadio mode, if equipped). • LINE IN (Auxiliary input jack) In AM, FM1, or FM2 mode: • Press SEEK to select preset stations within theselected radio band or press andhold...

There will also be one power leadfor each switch found as a blunt-cutand sealed wire located below theinstrument panel and to the left ofthe steering column. They are coded as follows: Switch Circuit number Wire color Fuse AUX 1 CAC05 Yellow 30A AUX 2 CAC06 Green withBrown Trace 30A AUX 3 CAC07 Viol...

Do not use the HomeLink 威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required byU.S. federal safety standards (this includes any garage door openermodel manufactured before April 1, 1982). A garage door which cannotdetect an object, signaling t...

• Continue to press and hold the HomeLink 威 button (note Step 2 in the Programming section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 . The indicator light will flash slowly and then rapidly aft...

2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the HomeLink 威 button, follow Step 1 in the Programming section. For questions or comments, contact HomeLink 威 at www.homelink.com or 1–800–355–3515. STANDARD MESSAGE CENTER (IF EQUIPPED) With the ignition in the on positi...

3. Once “OIL LIFE SET TO XXX%” is displayed, release and press theRESET control switch to change the Oil Life Start Value. Each releaseand press will reduce the value by 10%. System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the eve...

Warning display Status Low tire pressure (if equipped) Warning can be cleared by pressing the RESET button. Warning canreappear if the condition is stillpresent. Warning will reappear on thenext ignition key-cycle if the conditionstill exists. Tire monitor fault (if equipped) Tire sensor fault (if e...

CHECK AIR FILTER (Diesel engine only) — Refer to Instrument Cluster in your 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement. DRAIN WATER SEPARATOR (Diesel engine only) — Displayed when the water separator has reached a predetermined capacity andneeds to be drain...

OPTIONAL MESSAGE CENTER (IF EQUIPPED) With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the messagecenter for a display of status. Thesyste...

5. AIR FILTER (Diesel engine only) 6. DOOR AJAR 7. BRAKE SYSTEM 8. TBC GAIN = XX.XNO TRAILER (if equipped and no trailer connected) 9. TBC GAIN = XX.XOUTPUT = ////// (if equipped and trailer connected) 10. FUEL LEVEL Oil Life XXX% HOLD RESET = NEW An oil change is required whenever indicated by the ...

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with atailgate lock designed to helpprevent theft of the tailgate. • Insert ignition key and turn to theright to engage lock. • Turn ignition key to the left tounlock. Tailgate removal Your tailgate is removable to allow more room for loading....

2. Open the latches to release thepanels. 3. Rotate the panels toward thetailgate. Repeat Steps 1–3 for the other side of the bed extender. 4. Connect the two panels, then rotate both knobs a quarter-turnclockwise to secure the panels. 2009 F-250/350/450/550 (f23) Owners Guide, 2nd PrintingUSA (fus)...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency. If your vehicle is equipped with the SecuriLock™ Passive Anti-theftsystem, your keys are electronically coded to your vehicle; using anon-coded key wil...

5. Turn the ignition back to the on position. The horn will chirp one timeto confirm programming mode has been entered and is active. 6. To enable/disable the autolock feature, press the unlock control, thenpress the lock control. The horn will chirp once if autolock wasdeactivated or twice (one sho...

Your vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors withouta key. • lock all the vehicle doors withouta key. • activate the personal alarm. If there are problems with theremote entry system, make sure totake ALL remote entry transmitters with you to yo...

2. Press and release again within three seconds to confirm that all the doors are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parking lamps will flash once more. If any of the doors are not properly closed the horn will make two quickchirps and the parklamps...

Deactivating the memory feature To deactivate this feature: 1. Press and hold either memory 1 button or memory 2 button for fiveseconds. A tone will be heard after 1 1 ⁄ 2 seconds when the memory store is done, continue to hold until a second tone is heard after five seconds. 2. Within three seconds...

Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy additional remote entrytransmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for rep...

Perimeter lamps illuminated entry With the Remote Keyless Entry system, the following items willilluminate when the control on the transmitter is pressed: • Headlamps • Parklamps • Tail lamps The lamps will automatically turn off: • if the ignition switch is turned to the on position, or • the Remot...

Programming a personal entry code and keypad association tomemory seats, mirrors and pedals To create your own personal entry code: 1. Enter the factory set code. 2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be enteredwithin five seconds...

The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the control on the remote entry transmitter. • the ignition is turned to the on position. Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or yo...

Anti-theft indicator The anti-theft indicator is located in the instrument cluster. Vehicles equipped with theSecuriLock™ Passive Anti-theftsystem behave as follows: • When the ignition is in the offposition, the indicator will flash once every two seconds for a total of10 seconds to indicate the Se...

If not successful, the new coded key(s) will not start the vehicle’s engineand the theft indicator will flash on and off and you may repeat Steps 1through 5. If failure repeats, bring your vehicle to your authorized dealerto have the new spare key(s) programmed. PERIMETER ALARM SYSTEM (IF EQUIPPED) ...

SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before ret...

Captain’s chair (if equipped) • Lift the bar to move the seatforward or rearward. Make surethat the seat is relatched intoplace. • To recline the seatback, pull therelease lever handle located onthe side of the seat up. • Push down the lever (ifequipped) located at the bottomof the seatback to quick...

Press front to raise or lower thefront portion of the seat cushion. Press rear to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Using the manual lumbar support The lumbar support control islocated on the outboard side of theseat ...

Heated seats (if equipped) The heated seat control is located on the climate control panel. WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physicalconditions, must exercise...

To recall a memory position: • Press and release either memory 1 button or memory 2 button. A position can be recalled: • in any gearshift position if the ignition is not in the on position. • only in P (Park) or N (Neutral) if the ignition is in the on position. A memory seat position may be progra...

Push control to lower head restraint. WARNING: To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in itsproper position. The driver should never adjust the head restraintwhil...

To flip the seat cushion up, pull up on the lever located on the sideof the seat cushion to rotate thecushion up until it locks into avertical storage position, gainingaccess to the grocery hook locatedon the underside of the driver-sideseat cushion. The maximum load is25 lb. (11 kg). Returning the ...

WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belton the outside shoulder only. Never wear the shoulder belt under thearm. 2) Never swing the safety belt aro...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. Vehicle sensitive mode Combination lap and shoulder belts in normal retractor mode allow freeshoulder belt length adjustment to your movements and locking inresponse to vehicle movement. For example, if the driver brakessud...

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operatingproperly when checked by an authorized dealer. Failure to replace thebelt and retractor assembly could increase the risk of injury...

How to fasten the cinch tongue (Regular cab center seatingposition and Super Cab/Crew Cab rear center seating positions) 1. Pull the combination lap and shoulder belt from the retractor so thatthe shoulder belt portion of the safety belt crosses your shoulder andchest. 2. Be sure the belt is not twi...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label. Also, use the safety belt extension only if the safety belt is tooshort for you when fully extended. WARNING: Do not use extensions to change the fit...

WARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. WARNING: The National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 cm) between an occupant’s chest and the driver airbag modu...

WARNING: Removing the blocker beam without installing snow plow attachment hardware may effect airbag deployment in a crash. Do not operate the truck unless either the blocker beam orsnow plow attachment hardware is installed on the vehicle. Children and airbags For additional important safety infor...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainssufficient longitudinal deceleration.The fact that the airbags did notinflate in a collision does not meanthat something is wrong with thesystem. Rather, it means the forceswere not...

WARNING: If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injuryin a collision. The SRS consists of: • driver and passenger airbag modules (which include the inflators anda...

The S.O.S. Post Crash Alert can be turned off when any one of thefollowing actions are taken by the driver or any other person: • pressing the hazard control button, • or pressing the panic button on the remote entry transmitter. The feature will continue to operate until the vehicle runs out of pow...

WARNING: The safety belts for the driver and right front passenger seating positions have been specifically designed to function together with the airbags in certain types of crashes. Whenyou turn OFF your airbag, you not only lose the protection of theairbag, you also may reduce the effectiveness o...

• the vehicle has a rear seat too small to accommodate a rear-facinginfant seat; or • the infant has a medical condition which, according to the infant’sphysician, makes it necessary for the infant to ride in the front so thatthe driver can constantly monitor the child’s condition. 2. Child age 1 to...

• my vehicle has no rear seat; • the rear seat in my vehicle cannot accommodate a rear-facing infantseat; or • the infant has a medical condition which, according to the infant’sphysician, makes it necessary for the infant to ride in the front seat sothat the driver can monitor the infant’s conditio...

Important child restraint precautions WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be purchased separately from the vehicle.Failure to follow these instructions and guidelines may result in ani...

Recommendations for attaching child safety restraints for children Note: This vehicle is not equipped with LATCH lower anchors. RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Sa...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

restrained properly, then restrain the child in the child safety seat orwith the belt-positioning booster. Remember that child seats andbelt-positioning boosters vary and may be designed to fit children ofdifferent heights, ages and weights. Children who are too large for childsafety seats or belt-p...

Tether strap attachment 1. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, other wise routethe tether strap over the top of the seatback. If the top ...

Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child seat (e.g.,convertible or toddler seat) when they weigh about 40 lb (18 kg) and arearound four (4) years of age. Consult your child safety seat owner...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest and restsnugly near the center of the shoulder. The drawings below compare theideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. Information on transfer case operation and shifting procedurescan be found in the Driving chapter. Information on transfer case maintenance can be f...

Treadwear The treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernment test course. For example, a tire graded 150 would wear oneand one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The ...

Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, theycannot be treated like normal light truck tires. Tire service, includingadjusting tire pressure, must be performed by personnel trained,supervised and eq...

WARNING: Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that may be wedged in thetread grooves. Check for holes or cuts that may permit...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

• DRW – Six tire rotation If your vehicle is equipped with dualrear wheels it is recommended thatthe front and rear tires (in pairs) berotated only side to side. We do notrecommend splitting up the dualrear wheels. Rotate them side toside as a set/pair. After tire rotation,inflation pressures must b...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Warning Lamp will turn ON if the tire pressure is significantly low.Once the light is illuminated, ...

Low TirePressureWarning Light Possiblecause Customer Action Required Solid WarningLight Tire(s)under-inflated 1. Check your tire pressure toensure tires are properly inflated;refer to Inflating your tires in this chapter.2. After inflating your tires to themanufacturer’s recommendedinflation pressur...

Low TirePressureWarning Light Possiblecause Customer Action Required FlashingWarning Light Spare tire inuse Your temporary spare tire is in use.Repair the damaged road wheel andre-mount it on the vehicle torestore system functionality. For adescription of how the systemfunctions under these conditio...

TPMS reset procedure (if applicable) The TPMS reset tool is ONLY provided for vehicles with differentfront and rear tire pressures. The TPMS reset procedure needs tobe performed after tire rotation only on these vehicles. WARNING: To determine if your vehicle has different recommended pressures for ...

Storing the TPMS reset tool You should store the TPMS resettool in the provided pocket of theowner guide case; however, beforestoring it, you will need to removeand discard the loose strip ofVelcro 威 (this is the piece of Velcro 威 with the adhesive protection film onit); you will not need this porti...

and remain on for approximately five (5) seconds. If the light does notilluminate, the tool needs to be replaced. TPMS reset tips: • To reduce the chances of interference from another vehicle, TPMSreset should be performed at least three feet (one meter) away fromanother Ford Motor Company vehicle u...

7. Train the TPMS sensors in the tires using the following TPMS resetsequence starting with the left front tire in the following clockwise order: 1. Left front tire (Front driver’s side) 2. Right front tire (Front passenger’s side) 3. Right rear tire (Rear passenger’s side) 4. Left rear tire (Rear d...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. GCW (Gross Combined Weight) – is the...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fo...

Your vehicle may tow a Conventional/Class IV trailer or fifth wheel trailerprovided the maximum trailer weight is less than or equal to themaximum trailer weight listed for your engine and rear axle ratio on thefollowing charts. To calculate your maximum trailer weight: For pickup trucks: Take curb ...

Maximum GCWR - lb. (kg.) Engine Rear axle ratio Manual transmission Automatic transmission F–250 Pick-up 5.4L 3.73 15000 (6804) 16000 (7257) 4.10 17000 (7711) 18000 (8165) 6.8L 4.10 20000 (9072) 21000 (9525) 4.30 22000 (9979) 22500 (10206) F–350 Single Rear Wheel (SRW) Pick-up 5.4L 3.73 15000 (6804)...

Hitches WARNING: ON PICK-UP TRUCKS, the trailer hitch provided on this vehicle enhances collision protection for the fuel system. DO NOT REMOVE! Do not mount a ball hitch (sometimes referred to as a trailer ball hitchor trailer ball) to the bumper or use hitches that clamp onto the vehicle’sbumper o...

WARNING: Towing trailers beyond the maximum tongue weight exceeds the limit of the towing system and could result in vehicle structural damage, loss of vehicle control and personal injury. Weight distributing hitch When hooking up a trailer using a load equalizing hitch, always use thefollowing proc...

• TBC GAIN = XX.X NO TRAILER : The instrument cluster message center will display the current gain setting during a given ignitioncycle and when adjusting the gain. This message is also displayedduring manual activation without a trailer connected or when gainadjustments are made with no trailer con...

Note: This should only be performed in a traffic free environment at speeds of approximately 20–25 mph (30–40 km/h). 1. Make sure the trailer brakes are in good working condition,functioning normally, and properly adjusted. See your trailer dealer ifnecessary. 2. Hook up the trailer and make the ele...

Note: Your TBC can be diagnosed by your authorized dealer to determine exactly which trailer fault has occurred; however, if the faultis with the trailer this diagnosis is not covered under your Ford warranty. Points to Remember: • Remember to adjust gain setting before using the TBC for the firstti...

Driving while you tow When towing a trailer: • Do not drive faster than 70 mph (113 km/h) during the first 500 miles(800 km) of trailer towing and don’t make full-throttle starts. • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep grades. • C...

Tires • All trailer tires should be of the same size, and construction. • Select tires that meet the trailer loading requirements. • Always check tow vehicle and trailer tire pressure before towing. Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailerinto th...

Transmission Drivetrain configuration Requirements for neutral towing Manual 4x4 with manual-shift transfer case Transmission in (N) Neutral; Transfer case in (N) (Neutral); Hublocks set to FREE 1 Automatic Manual 4X2 or 4x4 with electronic-shift transfer case Do not tow your vehicle with any wheels...

STARTING Positions of the ignition 1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal. 2. Accessory— allows the electricalaccessories such as the radio tooperate while the engine is notrunning. This position also unlocksthe steering wheel. 3. On— all elect...

WARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. Ifthe engine idle speed does not slow down automatica...

How to Use the Engine Block Heater Ensure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth. Depending on the type of factory installed equipment, your engine blockheater system may consume anywhere between 400 watts or 1000 wattsof power per hour. Your factory i...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. If...

into four-wheel drive mode (if equipped), the traction control system willbe automatically disabled. Traction control operation will resume whenthe vehicle is placed back into two-wheel drive mode. WARNING: Aggressive driving in any road conditions can cause you to lose control of your vehicle incre...

• Do not fill the power steering pump reservoir above the MAX mark onthe reservoir, as this may result in leaks from the reservoir. If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls...

WARNING: Vehicles with a higher center of gravity such as utility vehicles and trucks handle differently than vehicles with a lower center of gravity. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slungsports cars are designed to per...

Used for improved traction on slippery roads. Selecting 3 (Third)provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additionalengine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • The tran...

To start the vehicle:1. Make sure the parking brake is fully set.2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral position. 3. Start the engine.4. Press the brake pedal and move the gearshift lever to the desiredgear; 1 (First) or R (Reverse).5. Release the parking ...

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rear-view camera system,located on the tailgate, provides avideo image, which ...

WARNING: Do not use the camera system with the tailgate open. If the back end of the vehicle is hit or damaged, then check with yourauthorized dealer to have your rear video system checked for propercoverage and operation. Night time and dark area use At night time or in dark areas, the camera syste...

• uses auto-manual hub locks that can be engaged and disengagedautomatically based on the 4x4 mode selected. • auto-manual hub locks can bemanually overridden by rotatingthe hub lock control from AUTOto LOCK if desired. • automatic operation of thehub locks is recommended, and will increase fuel eco...

2H (2WD) – For general on-road driving. Sends power to the rear wheels only. 4H (4x4 High) – For winter and off-road conditions. Sends power to front and rear wheels. This mode is not intended for use on dry pavement. N (Neutral) – Only used when towing the vehicle. 4L (4x4 Low) – For low-speed off-...

Shifting from 4H (4x4 High) to 2H (2WD) Move the transfer case lever to 2H(2WD) at a stop or a vehicle speedbelow 5 mph (8 km/h). With the vehicle at complete stop,disengage the locking hubs(optional) by rotating the hub lockcontrol from LOCK to FREE. • For proper operation, makesure that both indic...

5. If shifting to 2H (2WD) with the vehicle at a complete stop, disengagethe locking hubs (optional) by rotating the hub lock control from LOCKto FREE. Using the N (Neutral) position The transfer case neutral position overrides the transmission andputs the vehicle in neutral regardless of transmissi...

Shifting from 2WD to 4x4 HIGH Rotate the 4x4 control to the 4x4HIGH position at speeds up to55 mph (88 km/h). • The electronic shift 4x4system is designed to engage4x4 HIGH when the vehicle ismoving. If shifted to 4x4HIGH while at complete stop,4x4 may not engage and the4x4 indicator may flashcontin...

3. Move the 4x4 control to the 4x4LOW position. 4. Hold the shift conditions until the4x4 LOW indicator light illuminates. 5. If the 4x4 LOW indicator lightflashes continuously for more than10 seconds, allow the vehicle tomove at a speed below 5 mph(8 km/h), then repeat steps 2through 5 while the ve...

WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drivevehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars...

WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drivevehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars...

Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Even 4WD vehicles can lose traction in slick mud. Aswhen you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until ...

When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This reduces strain on theengine and the possibility of stalling. If you do stall out, do not try toturn around because you might rollover. It is better to ...

VEHICLE USED AS A STATIONARY POWER SOURCE Auxiliary equipment called power take-off, or PTO, is often added to theengine or transmission to operate utility equipment. Examples include awheel-lift for tow trucks, cranes, tools for construction or tire service,and pumping fluids. PTO applications draw...

SNOWPLOWING Ford recommends that the Super Duty F-Series used for snow removalinclude the Snow Plow Package Option. Installing the snowplow Weight limits and guidelines for selecting and installing the snowplow canbe found in the Ford Truck Body Builders Layout Book, Snowplow section, found at www.f...

• The snow plow prep package includes a unique powertrain controlstrategy which is required for diesel engine cooling during highwaydriving with the snowplow raised. Operating the vehicle with the snowplow attached Do not use your vehicle for snow removal until it has been driven atleast 500 miles (...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you maypurchase extended coverage prior to your Basic Warranty’s RoadsideAssistance expiring. For more information and enrollment, contact1...

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. This switch is located on thepassenger’s side of the instrum...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located in thepassenger’s footwell. Remove thepanel cover to access the fuses. To remove the fuse panel cover, pullthe panel toward you. When theclips of the panel disengage, let thepanel fall easily. To remove a fuse use the fuse pullertool provide...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Not used (spare) 2 15A Not used (spare) 3 15A Family Entertainment System(FES) 4 30A Not used (spare) 5 10A Keypad illumination, Brake-ShiftInterlock (BSI), SPBJB 6 20A Turn signals 7 10A Left headlamp (Low ...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 29 5A Not used (spare) 30 5A Not used (spare) 31 10A Not used (spare) 32 10A Restraints Control Module (RCM),Passenger Airbag DeactivationIndicator 33 10A Trailer tow brake controller,Trailer tow battery charge relaycoil 34 5A Not used (spare) 3...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 45 5A Front wiper logic, Blower motorrelay coil 46 7.5A Not used (spare) 47 30A Circuit Breaker Power windows, Moon roof,Power Sliding Backlite 48 Relay Delayed accessory Power distribution box The power distribution box is located in the engine...

Your vehicle may be equipped with a conventional spare tire that isdifferent in one or more of the following: type, brand, size, speed ratingand tread design. If this is the case, this dissimilar spare tire is still ratedfor your vehicle loads (GAWR and GVWR).Temporary spare tires are notequipped wi...

• Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to im...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

Use of a temporary spare tire at any one wheel location can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability Stopping and securing the veh...

Location of the spare tire and tools If your vehicle is equipped with a spare tire, jack and associated tools,refer to the following table for their locations: Tool Location Spare tire (pick-up trucks only) Under the vehicle, just forward ofthe rear bumper Jack Regular cab and Crew Cab:Fastened to f...

• Vehicles equipped with dualrear wheels, insert the lug wrench extension into the lugwrench to reach the lug nuts. 2. Attach the spare tire lock key (A)to the jack handle (B). 3. Fully insert the jack handle (withone extension) through the bumperhole and into the guide tube. Thekey and lock will en...

WARNING: To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side andend of the vehicle) to the tire being changed. WARNING: If the vehicle slips off the jack, you or someone else co...

13. Insert the jack handle into thepump linkage. 14. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground. Hydraulic jacks are equippedwith a pressure release valvethat prevents lifting loads whichexceed the jack’s rated capacity. 15. Remove the lug nuts with the...

10–lug nut torque sequence 19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicle is equipped with a spare tire carrier. Note: Do not stow the Harley-Davidson flat tire and wheel using the spare tire winch mechanism; store the flat in the bed of the truck. 20. Stow the jack, jac...

If the ornament retention towers arealigned between the studs/lug nuts,the ornament is improperlyinstalled. This improper installationmay appear and sound correct, butwill not keep the ornament on thevehicle. Ornaments improperlyinstalled in this manner will fall offor become loose with minimal forc...

5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, per scheduled maintenance information), or at any time that the spare tire is disturbed through service of othercomponents. 6. If removed, install the spare tire lock (if equipped) into the bumperdrive ...

Inspect the wheel pilot hole prior toinstallation. If there is visiblecorrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot surface (1...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect t...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that the vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbe...

Note: Towing an ESOF 4x4 vehicle with the front wheels on the ground without disengaging the front hubs may cause damage to the automatictransmission. Note: Towing a 4x2 or an ESOF 4x4 vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph(56 km/h) may c...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized dealer handlingyour vehicle line will provide warranty service, we recommend youreturn to your selling authorized dealer who wants to ensure yourcon...

In Canada: Mailing Address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing Address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent quality product to help protect from environmentaleffects. WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Pr...

• 6.8L V10 gasoline engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRem...

INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area firstwith Mo...

LEATHER SEATS FOR THE KING RANCH F-250 AND F-350 CREWCAB ONLY (IF EQUIPPED) Your vehicle is equipped with seating covered in premium, top-grainleather which is extremely durable, but still requires special care andmaintenance in order to ensure longevity and comfort. Regular cleaning and conditionin...

Conditioning Bottles of King Ranch Leather Conditioner are available at the KingRanch Saddle Shop. Visit the Web site at www.krsaddleshop.com , or telephone (in the United States) 1–800–282–KING (5464). If you areunable to obtain King Ranch Leather Conditioner, use another premiumleather conditioner...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Customer Infor...

2. Block the wheels. WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left c...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Refer to the 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 5.4L V8 gasoline engines 1. Windshield washer fluid reservoir 2. Battery 3. Transmission fluid dipstick (automati...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from thearm. 2. Attach the new wiper to thewiper arm and press it into placeuntil a...

• 5.4L/6.8L gasoline engines only;for diesel engine information,refer to the 6.0 and 6.4 Liter Direct Injection Turbo DieselOwner’s Guide Supplement. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acc...

4. Install the dipstick and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise1/4 of a turn until three clicks are heard or until the cap is fully seated. To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level dipstick a...

It is recommended you use the appropriate Motorcraft oil filter oranother with equivalent performance for your engine application. BATTERY WARNING: This vehicle may be equipped with more than one battery, removal of cablefrom only one battery does notdisconnect the vehicle electricalsystem. Be sure ...

WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle orbattery. Lift the battery with a battery carrier or with your hands onopposite corners. WARNING: Keep batteri...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

• Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer to Maintenance product specifications and capacities in this chapter. Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, ...

Add the proper mixture of coolant and water to the cooling system byfollowing these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tur...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. If your vehicle is equipped with a diesel engine, refer to the Maintenance Product Specifications and Capacities section of your 6.0 a...

WARNING: Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehicle to aservice facility as soon as pos...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The vehicle warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. WARNING: The fuel system may be under pres...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline with apump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” inhigh altitude areas that are sold with octane ratings less than 87. Do not be concerned if your engine sometimes kno...

• Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump a...

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed: 15 minutes of steady driving on an ex...

7. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it is between the MIN and MAX range. Refer to Maintenance Products Specifications and Capacities in this chapter for the proper fluid type. Be sure to put the cap back on the reservoir. BRAKE FLUID • Vacuum boos...

CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to scheduled maintenance information for the service interval schedules. During normal operation, the fluid level in the clutch reservoir shouldremain constant. If the fluid level drops, refill the fluid level to the stepin the reservoir. Use o...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at thebottom of the opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. I...

AIR FILTER Refer to the scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter. The following procedure is for vehicl...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ........................110 Air cleaner filter ...............402–403 Air conditioning ..........................84 Airbag supplemental restraintsystem ........................................192 and child safety seats ............194description ..............................192dis...

recommendations ...................375refill capacities ........................405 Event data recording ....................7 Exhaust fumes ..........................277 F Fail safe cooling ........................383 Family entertainment system ....51 Fluid capacities .........................405 ...