Ford 2008 Mustang v.2- User Manual

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Base instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights ...

Service Engine Soon: The Service Engine Soon indicator light illuminates when the ignition is firstturned to the ON position to checkthe bulb and to indicate whether the vehicle is ready forInspection/Maintenance (I/M) testing. Normally, the ⬙ Service engine soon ⬙ light will stay on until the engin...

Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehiclechecked by your authorized dealer. Driving extended distances withthe parking brake engaged can cause brake fail...

Engine coolant temperature: Illuminates when the engine coolanttemperature is high. Stop thevehicle as soon as possible, switch off the engine and let cool. Refer to Engine coolant in the Maintenance and Specifications chapter. Never remove the coolant reservoir cap while the engine isrunning or hot...

Speed control (if equipped): Illuminates when the speed controlis engaged. Turns off when thespeed control system is disengaged. Door/Trunk ajar (if equipped): Illuminates when the ignition is inthe ON position and any door ortrunk is open. Anti-theft system: Flashes when the SecuriLock™ Passive Ant...

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’s dooris opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedriver’s door is...

Refer to Message center (if equipped) in the Driver Controls chapter to select one of six preset colors or one user definable color (MyColor)for the nighttime gauge backlighting. Speedometer: Indicates the current vehicle speed. • Base instrument cluster • Optional instrument cluster Engine coolant ...

AUDIO SYSTEMSQuick start — How to get going Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus offthe road. The drivers primary responsibility is the safe operat...

For a single CD system, if a disc is not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the display. The firsttrack on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot numbe...

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random play. Otherwise,random play will begin when the current track is finished playing. CDSHUF will appear in the display.To disengage, press SHUFFLE again. ...

6. / OK(Play/Pause): This control is operational in CD/MP3mode. When a CD/MP3 is playing,press to pause or resume play. The CD status will display in the radiodisplay. OK: Use in various menu options. 7. SHUFFLE: Press to play tracks in random order. 8. FOLDER : In folder mode, press FOLDER to acces...

Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus offthe road. The drivers primary responsibility is the safe operation oftheir vehicle. Only use cell phones an...

• ENABLE ALERTS / DISABLE ALERTS: Press OK to enable/disable the satellite alert status which alerts you when your selected songs areplaying on a satellite radio channel. (The system default is disabled.)SONG ALERTS ENABLED/DISABLED will appear in the display. Themenu listing will display the opposi...

OCCUPANCY mode: Use / select and optimize sound for ALL SEATS, DRIVERS SEAT, REAR SEATS or CONVERTIBLE (if equipped). SPEEDVOL (Speed sensitive volume): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louder withincreasing vehicle speed to compensate for road and wind noise...

5. SEEK : In radio and CD/MP3 mode, press to access the previous ( ) or next ( ) strong station or track. In satellite radio mode (if equipped), press SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz,Rock, News, etc.), press SEEK, SEEK to seek to the previous/next...

To play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off. 2. Ensure that the battery in your portable music player is new or fullycharged and that the device is turned off. 3. Attach one end of the audio extension cable to the headp...

5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the portable music player should be stored in a securelocation, such as the center console or the glove box, when the vehicle isin motion. The audio exte...

Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm)audio compact discs only. Due to technical i...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly. NO TEXT Category information not available. Category information not available at this time on this channel. The sy...

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Temperature selection: Controls the temperature of the airflow in the vehicle. 2. Mode selections: Controls the location of the airflow in the vehicle. See the following for a brief description of each selection. MAX A/C: Distributes recirculated air thr...

4. Passenger heated seat: Press to activate or deactivate the passenger side heated seat. The passenger heated seat will turn offautomatically after 10 minutes of use. 5. R Rear defroster: Press to activate/deactivate the rear window defroster. Refer to Rear window defroster later in this section fo...

For maximum cooling performance in panel or panel/floor modes: 1. Move temperature control to the coolest setting. 2. Select A/C and recirculated air ( ) to provide colder airflow. 3. Set the fan to the highest speed initially, then adjust to maintaincomfort. To aid in side window defogging/demistin...

CABIN AIR FILTER Your vehicle is equipped with a cabin air filter, which is located just infront of the windshield under the cowl grille on the passenger side of thevehicle. The particulate air filtration system is designed to reduce theconcentration of airborne particles such as dust, spores and po...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Fog lamp control (if equipped) The fog lamps can be turned onwhen the ignition is in the ONposition, the headlamp control is inthe or position and the ...

Flash to pass Pull toward you, to the first detent,to activate and release to deactivate. Note: Vehicles equipped with HID headlamps will hear an audible clickwhen activating this feature. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. When activated, the DRL...

Function Trade Number Headlamp H13 * HID (high intensity discharge) headlamp (ifequipped) D3R Park lamp, turn lamp, side marker (front) 3157 or 3157K Sidemarker (front) W5W or W5WL Fog lamp 9145–GT or H11–Pony (if equipped) Tail lamp, brakelamp, turn lamp 3057K or 4057K Sidemarker (rear) W5W or W5WL...

1. Make sure headlamp switch is inthe off position, then open thetrunk. 2. Carefully remove fastenersaround the lamp area and thenremove the interior trunk trim. 3. Remove three nut and washerassemblies and the lamp assemblyfrom the vehicle. 4. Disconnect the electrical grommetby pulling it straight...

4. Carefully pull the bulb straightout of socket. Install the new bulb in reverseorder. Replacing license plate lamp bulbs 1. Make sure the headlamp switch isin the off position, then remove thetwo screws and the license platelamp assembly. 2. Remove bulb socket by turningcounterclockwise. 3. Carefu...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control up oneposition. Adjust the rotary control to thedesired speed setting. For normal or low speed wiperoperation, move control up twopositions from off. For high speed wiper operation,move control up three positionsfrom off...

Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Check the washer fluidlevel frequently. Do not operate the wipers when the windshield is dry.This may scratch the glass, damage the wiper blades and cause the wipermotor to burn out. Befor...

POWER WINDOWS Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the proximity of the ...

Restoring the Express up functionality (Front windows only) Under low battery power conditions, Express Up only functionality maybe lost. To reset this function after restoring full battery power, pull theswitch to the Express Up position, hold the switch until the glassreaches the stall position an...

the window until it completes its travel and hold the switch down for 2seconds. Immediately after releasing the window down switch, pull theswitch up to raise the window until it completes its travel and hold theswitch up for 2 seconds. Perform Short drop re-calibration with doors closed only. Re-Ca...

5. Repeatedly press until your zone number is shown in the mirrordisplay, then release. 6. The display will show all segments, then return to normal compassmode within ten seconds. Compass calibration adjustment Perform this adjustment in an open area free from steel structures andhigh voltage lines...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...

• Press and release the SET + control to operate the Tap-Up function.Each tap will increase the set speed by 1 mph (1.6 km/h). • Use the accelerator pedal to get to the desired speed. When thevehicle reaches that speed press and release the SET + control. Reducing speed while using speed control The...

Installation of the boot (if equipped) Be sure the boot is secure on the vehicle before driving. 1. Install the boot on the vehicle by hooking the boot retaining clips onthe back panel.2. Install the boot on the right side tucking in the front part of the bootin the quarter panel and hooking the ret...

Storing the boot 1. Position the boot right-side up and fold each side of the boot inward. 2. Turn the boot upside down and fold the left side of the boot inward. 3. Fold the right side inward and secure the boot with the strap. Stow the boot in the trunk. Raising the convertible top The convertible...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status. Thesystem will a...

Pressing the RESET control cycles the message center through each ofthe systems being monitored. The sequence of the system check report and how it appears in themessage center is as follows: 1. OIL PRESSURE 2. CHARGING SYSTEM 3. DRIVER DOOR 4. PASSENGER DOOR 5. TRUNK 6. SECURITY SYSTEM (if equipped...

2. Pressing the RESET controlcycles the message center througheach of the language choices. 3. Press and hold the RESETcontrol to set the language choice. Info menu This control displays the followingcontrol displays: • Odometer/Trip odometer • Distance to Empty • Average Fuel Economy • Instantaneou...

Dual mode display The DTE function will display LOW FUEL LEVEL and sound a tone forone second when you have approximately 50 miles (80 km) to empty. Ifyou RESET this warning message, this display and tone will returnwithin 10 minutes. DTE is calculated using a running average fuel economy, which is ...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for 4seconds. The message center will display the last...

TIRE PRESSURE SENSOR FAULT. Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For moreinformation on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter. If th...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

Smart locks This feature helps prevent you from locking yourself out of the vehicle ifyour key is still in the ignition. When you open the driver’s door and you lock the vehicle with thepower door lock control, all the doors will lock, then the driver’s doorwill automatically unlock reminding you th...

Autolock (if equipped) On vehicles equipped with an automatic transmission, this featureautomatically locks all vehicle doors when: • all doors are closed, • the ignition is in the 3 (ON) position, • the brake is pressed before reaching 5 mph (8 km/h), and • the vehicle increases to more than 5 mph ...

Replacing the battery The remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING...

Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy additional remote entrytransmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for rep...

The dome lamp control must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 10 minutes after theignition ha...

3. Turn the ignition to the 3 (ON) position; the horn will chirp toindicate the driver configuration mode has been activated. Activating or deactivating the perimeter lighting once in program mode isaccomplished by: • pressing the trim panel power door unlock control ( ) twice within five seconds. A...

Anti-theft indicator The anti-theft indicator is located inthe instrument cluster. • When the ignition is in the 1 (OFF/LOCK) position, the indicator willflash once every 2 seconds to indicate the SecuriLock™ system isfunctioning as a theft deterrent. • When the ignition is in the 3 (ON) position, t...

Replacement keys If your keys are lost or stolen and you don’t have an extra coded key,you will need to have your vehicle towed to an authorized dealer. Thekey codes need to be erased from your vehicle and new coded keys willneed to be programmed. Replacing coded keys can be very costly. Store an ex...

driver door key cylinder, the system will monitor the doors,trunk, and hood but the motion sensing and vehicle inclinesensing will not arm. Do not arm the interior motion detection system if movement within thevehicle is likely to occur. Additionally, do not arm the vehicle inclinesensing system whe...

Disarming the system You can disarm the active anti-theft system by any of the followingactions: • Unlock the doors by using the remote entry transmitter. • Unlock the driver’s door with the key in the door lock cylinder. • Turn the ignition to the 3 (ON) position with a programmed codedignition key...

SEATING Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to its or...

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on theseat. Allow the seat to dry thoroughly. The heated seat control is located in the lower center of the instrumentpanel. To operate the heated seats: • Push control ...

Front passenger sensing system For airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants that are very closeto the airbag when it begins to inflate. For some occupants, like infantsin rear-facing child seats, this occurs because the...

Safety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit in the backseat where they can be properly restrained. Never let a passenger hold a child on his or her lap while thevehic...

Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Combination lap and shoulder belts The presenter arm (available on the coupe only) is intended to impr...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The center of the rear seat is NOT designed as a seating position and is not equipped with safety belts. The LATCH anchors were not designed to be used with a child seat in the centerposition and there is no tether anchor a...

Failure to replace the Belt and Retractor assembly couldincrease the risk of injury in collisions. The front and rear safety restraints in the vehicle are combination lapand shoulder belts. The front passenger and rear seat safety belts havetwo types of locking modes described below: Vehicle sensiti...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recom...

Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severe personal injuries in the event of a collision. For proper care of soiled safety belts, refer to Interior in the Cleaning chapter. Safety belt warning light and indicator chime The sa...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of th...

Never place your arm over the airbag module as a deployingairbag can result in serious arm fractures or other injuries. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly one or tw...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. Front pa...

The front passenger sensing systemuses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind youthat the front passenger frontal airbag is disabled. The indicator lamp islocated on the top right corner of the center stack of the instrumentpanel abov...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected bythe collision will be inflated. The front passenger sensing system willturn off the passenger seat side airbag if the seat is empty. The airbagwas des...

A difficulty with the system is indicated by one or more of the following: • The readiness light will eitherflash or stay lit. • The readiness light will notilluminate immediately afterignition is turned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the p...

Children and safety belts If the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as specified by your child safetyseat manufacturer) should always wear safety belts. Follow all the important safety restraint and airbag precautions that...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

Carefully follow all of the manufacturer’s instructions includedwith the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a suddenstop or collision. Rear-facing child seats or infant carriers should never be placedin front of an...

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate itis in the automatic locking mode. 7. Pull the lap belt p...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

Note: The attachments for the convertible boot located on the backof the head restraints are not tetheranchors. 4. Access tether anchors locatedbehind the seatback under the vinyltag marked with the child tetheranchor symbol. 2008 05+ Mustang (197) Owners Guide (post-2002-fmt)USA (fus) Seating and S...

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol. The center of the rear seatis NOT designed as a seating position and is notequipped with safety belts. TheLATCH anchors were not designedto be used with a child seat in thecenter pos...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If thebeads do not seat at the maximum pressure indicated, re-lubricate andtry again.When inflating the tire for m...

• Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over ...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tir...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Pressure Warning Lamp will turn ON if the tire pressure issignificantly low. Once the light is illu...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

Low TirePressureWarning Light Possiblecause Customer Action Required Flashing WarningLight Spare tire inuse Your temporary spare tire is in use.Repair the damaged road wheel andre-mount it on the vehicle to restoresystem functionality. For adescription of how the systemfunctions under these conditio...

SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss ofvehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. Snow tires must be the same size, load index, speed rating asthose originally provided by Ford...

capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’sTire Lab...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cross thechains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agen...

• Shift out of D (Overdrive) into D (Overdrive cancelled) or a lowergear (3, 2, or 1) when towing up or down steep hills. This willeliminate excessive downshifting and upshifting for optimum fueleconomy and transmission cooling. • Anticipate stops and brake gradually. Servicing after towing If you t...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. Note: The ignition key cannot be removed from the ignition unlessthe gearshift lever is securelylatched in P (Park). 2. ACCESSORY, allows the electricalaccessories su...

3. Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (ST...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.5 cm) or adjust the heatingor air conditioning to bring in fresh air. ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coola...

Parking brake To set the parking brake (1), pullthe parking brake handle up as faras possible. The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released. To release, press and hold the button (2), pull the handle up slightly,then push the handle down. Always...

STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until itstops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering fluid level(below the MIN mark on the reservoir)...

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the ON position unless the brake pedal is depressed.If you cannot move the gearshi...

• To return to Overdrive mode, press the transmission control switch.The O/D OFF lamp will not be illuminated. • Overdrive mode is automatically returned each time the key is turnedoff. 3 (Third) This position allows for third gear only. • Provides engine braking. • To return to D (Drive) without Ov...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transmission has a starter interlock that prevents crankingthe engine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then pu...

Recommended shift speeds Do not downshift into 1 (First) when your vehicle is movingfaster than 15 mph (24 km/h). This will damage the clutch. Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 11 mph (18 km/h) 2 - 3 19 mph (31 ...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for th...

Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in the glove compartment. In Canada, the card isfound in the Customer Information Guide in the glove com...

FUEL PUMP SHUT-OFF SWITCH FUEL RESET This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. The fuel pump shut-off switch islocated in the dr...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 17 10A Restraint Control Module (RCM),Passenger Occupant DetectionSystem (PODS), Passenger Airbag Deactivation Indicator (PADI) 18 10A Anti-lock Brake System (ABS) 19 5A Powertrain Control Module (PCM)relay, Passive Ant...

Auxiliary relay with HID headlamps 1. Left HID headlamp 2. Right HID headlamp 3. Not used On vehicles equipped with HID headlamps, an auxiliary relay box islocated under the hood on the right hand side front of the enginecompartment. This auxiliary relay box contains the left front and rightfront HI...

Have a flat tire serviced by an authorized dealer in order to preventdamage to the TPMS sensor, refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels, and Loading chapter. Replace the spare tire with a road tire as soon as possible. During repairing or replacing ofthe flat tire, have ...

When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

TEMPORARY MOBILITY KIT (IF EQUIPPED) Your vehicle may be equipped with a temporary mobility kit (located inthe spare tire well in the trunk). The temporary mobility kit consists ofan air compressor to reinflate the tire and a sealing compound that willeffectively seal most punctures caused by nails ...

• Do not drive farther than 120 miles (200 km). Drive only to the closest authorized dealer or tire dealer. • Drive carefully and avoid abrupt steering maneuvers. • Periodically monitor tire inflation pressure in the affected tire; if thetire is losing pressure, have the vehicle towed. • Read the in...

Note: When the sealing compound is first added into the tire, the airpressure gauge reading (7) on thecompressor unit may increase up to90 psi; this is normal and should beno reason for concern. The pressurewill drop after about 30 seconds ofoperation. Do not stand directly over the temporary mobili...

Second stage: Checking tire pressure 1. Stop driving after approximately two miles. Then check the airpressure of the damaged tire as follows: • Ensure the compressor is turned off by pressing the “O” side of theorange button. • Remove the hose and the cable with the electrical plug from the kit’sst...

2. If the air pressure reads 19 psi (131 kPa) or higher, switch the aircompressor on by pressing the “I” side of the orange button and adjustthe air pressure to the recommended pressure. This pressure can befound on a label affixed to the B-Pillar or the edge of the driver’s door. Ifthe air pressure...

4. Insert the electrical plug into the vehicle’s power point. 5. Start the engine (only if the vehicle is outdoors or in a well-ventilated area) to prevent the vehicle’s battery from draining. 6. Read the air pressure gauge on the temporary mobility kit. If the tire pressure needs to be increased, o...

JUMP STARTING The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your automatic transmissionv...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

Emergency Towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent quality product to help protect from environmentaleffects. WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Pr...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

4.6L 3V SOHC V8 ENGINE PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and w...

• Do not use household or glass cleaners as these may damage thefinish of the instrument panel, interior trim and cluster lens. Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination of the airbag system. If a staining liquid like...

On vehicles equipped with seat-mounted airbags, do not usechemical solvents or strong detergents. Such products could contaminate the side-airbag system and affect performance of the sideairbag in a collision. LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. To reduce the risk of vehicle damage and/or person...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power distribution box...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

• 4.0L V6 engine • 4.6L 3V V8 engine 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the lower hole, add enough oil to raise thelevel within ...

• 4.0L V6 engine • 4.6L 3V SOHC V8 engine • Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Check...

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above thenormal operating ra...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer to Maintenance product spec...

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come outforcefully when the cap is loosened slightly. Add the proper mixture of coolant and water to the cooling system...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications...

4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Restart the engine and take your vehicle to an authorized dealer. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your veh...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

At the next opportunity, safely pull off of the road, remove the fuel fillercap, align the cap properly and reinstall it. The check fuel caplight or “check fuel cap” message may not reset immediately; it may take several driving cycles for the check fuel cap light or “check fuel cap” message to turn...

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel ga...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may re...

POWER STEERING FLUID Check the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. 1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetwee...

BRAKE/CLUTCH FLUID Brake and clutch systems are supplied from the same reservoir. The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. ...

Use of a non-approved automatic transmission fluid may causeinternal transmission component damage and void the warranty. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may affect transmissionoperation and result in damage to internal t...

• Fill level for V6 • Fill level for V8 4. Add enough fluid through the filler opening to bring the fluid up tothe recommended levels. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section ...

ENGINE DATA Engine 4.0L V6 engine 4.6L V8 engine Cubic inches 245 281 Required fuel 87 octane 87 octane 2 Firing order 1-4-2-5-3-6 1-3-7-2-6-5-4-8 Ignition system EDIS Coil on plug Spark plug gap 0.052–0.056 inch(1.32–1.42 mm) 0.040–0.050 inch(1.02–1.27 mm) 1 Compression ratio 9.7:1 9.8:1 1 The spar...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ..........................63 Air cleaner filter ...............269–271 Airbag supplemental restraintsystem ................................118, 126 and child safety seats ............120description ......................118, 126disposal ....................................129driver...