Ford 2008 Ford Taurus - Manual

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal...

other government authorities or other third parties acting with lawfulauthority. Other parties may seek to access the informationindependently of Ford Motor Company and Ford of Canada. Cell phone use The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of busine...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap (if equipped): Illuminates when the fuel cap maynot be properly installed. Continueddriv...

Airbag readiness: If this light fails to illuminate when the ignition isturned to ON, continues to flash orremains on, have the systemserviced immediately by your authorized dealer. A chime will also soundwhen a malfunction in the supplemental restraint system has beendetected. Safety belt: Reminds ...

Low fuel (if equipped): Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is engaged. Turnsoff when the speed control systemis disengaged. O/D off: Illuminates when the overdrive function of the...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMSQuick start — How to get going Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus offthe road. The drivers primary responsibility is the safe operat...

For a single CD system, if a disc is not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the display. The firsttrack on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot numbe...

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random play. Otherwise,random play will begin when the current track is finished playing. CDSHUF will appear in the display.To disengage, press SHUFFLE again. ...

Recommended level is 1–3; SPEED OFF turns the feature off and level 7 is the maximum setting. TRACK/FOLDER MODE: Available only on MP3 discs in CD mode. In track mode, press SEEK, SEEK to scroll through all tracks on the discIn folder mode, press SEEK, SEEK to scroll through tracks within the select...

(Jazz, Rock, News, etc.), press SEEK, SEEK to seek to the previous/next channel in the selected category. Press and hold SEEK, SEEK to fast seek through the previous /next channels. In TEXT MODE, press SEEK, SEEK to view the previous/additional display text. In CATEGORY MODE, press SEEK, SEEK to sel...

In CATEGORY mode (if equipped), press to scroll through the list of available SIRIUS channel categories. Satellite radio is available only with a valid SIRIUS radiosubscription. Check with your authorized dealer for availability. 2. (Phone): Your vehicle may be equipped with the SYNC systemwhich has...

The default setting is off; increasing your vehicle speed will not change the volume level. Adjust 1–7: Increasing this setting from 1 (lowest setting) to 7 (highest setting) allows the radio volume to automatically change slightly withvehicle speed to compensate for road and wind noise. Recommended...

5. SEEK : In radio mode, press / to access the previous/next strong station. In CD mode, press / to access the previous/next CD track. In satellite radio mode (if equipped) , press SEEK, SEEK to seek to the previous/next channel. If a specific category is selected,(Jazz, Rock, News, etc.), press SEE...

In TEXT MODE, sometimes the display requires additional text to be displayed. When the “>” indicator is active, press SEEK to view the additional display text. When the “<” indicator is active, press SEEK to view the previous display text. 14. AM/FM: Press to select AM/FM1/FM2 frequency band. ...

USB port (if equipped) Driving while distracted can result in loss of vehicle control,accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus offthe road. The drivers primary responsibility is the safe operation oftheir vehicle. ...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere with your reception. • Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result ...

Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and play a variety of standard video game systems. TheDVD player is capable of playing standard DVDs, CDs, MP3s and iscompatible with CD-R/W, CD-R and cer...

2. Adjust the volume levels usingthe volume controls on the DVDsystem. To adjust display brightness: To decrease/increase the brightnesslevel on the display screen, pressthe brightness control on the DVDsystem. A display will appear at thebottom of the screen indicating thebrightness level. The brig...

15. ENTER: Press to select/confirm the current selection. 16. Cursor /Brightness controls: Use the cursor controls to makevarious selections when in anymenu. When not in a menu, and inDVD mode, press / to adjust the brightness. A display bar will appear at the bottom of the screenindicating the brig...

1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF. 2. Cursor controls: Use in various active menus to advance the cursor up/down/left/right. When not in a Menu, the left and right cursor controlsdecrease and increase the display brightness. 3. DISPLAY: Press to access the ...

23. ILLUMINATION : Press to illuminate the remote control and backlight all of the buttons. Battery replacement Batteries are supplied with the remote control unit. Since all batterieshave a limited shelf life, replace them when the unit fails to control theDVD player. Remove the screw and unlatch t...

Wired headphones Do not leave children unattended in the vehicle and do not letchildren operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may becomeentangled in the cords and seriously injure themselves. The driver should never use the headphones whil...

FULL (enabled): The FES has control over the primary (speaker) and secondary (headphone) audio sources. LOCAL : The FES has control over the secondary source (headphones) only. The radio will ignore button presses that affect the primary(speaker) audio source. LOCKED (disabled): The FES buttons are ...

use this product in any commercial (i.e. revenue generating) real timebroadcasting (terrestrial, satellite, cable and /or any other media)broadcasting/streaming via internet, intranets and/or other networks or inother electronic content distribution systems, such as pay-audio oraudio-on-demand appli...

Be sure to review User Manuals for video games and video gameequipment when used as auxiliary inputs for your Family EntertainmentSystem (FES). Do not operate video games or video equipment if the power cordsand/or cables are broken, split or damaged. Carefully place cords and/orcables where they wi...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/decrease the airflow...

Dual Zone Automatic Temperature Control with heated seats(if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/de...

• Do not put objects under the front seats that will interfere with theairflow to the back seats. • Remove any snow, ice or leaves from the air intake area at the base ofthe windshield. • For maximum cooling performance (MAX A/C): In AUTO mode, press AUTO control and set to desired temperature. In m...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

3. Turn the ignition switch to RUN and then back to LOCK. 4. Turn the headlamp switch to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamp switch to . The headlamps will turn off. Fog lamp con...

Flash to pass Pull toward you to activate andrelease to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output.To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF, autolamps or parking lampposition and • the transmi...

Your vehicle may also have readinglamps within the rear dome lamp(s). Press the switches on either side ofthe dome lamp to turn on thelamps. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize pressure. When moist air entersthe headlamp(s) through the vents, there is a possib...

Function Number of bulbs Trade number Fog lamp (if equipped) 2 H11 Map lamp 2 12V6W Dome/reading lamps 3 578 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer. Replacing the interior bulbs Check the operation of all bulbs...

2. Reach in behind the headlamp assembly to access the bulb socketsand connectors. 3. Remove the inboard rubber bootfrom the lamp assembly by pullingrearward. 4. Remove the bulb socket byturning it counterclockwise andpulling it straight out. Handle a halogen headlamp bulb carefully and keep out ofc...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down and hold the steeringwheel release control. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Pull the steering wheel releasecontrol up. This will lock thesteering wheel in position. Never adjust the steering wh...

INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may beused to secure sunglasses or similarsized objects. Press the control toopen the storage compartment. OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment Th...

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Theseinclude: 1. Cupholders 2. Utility compartment with coinholder, a clamshell tray, audio inputjack, USB port and power point 3. Rear power point, vent and (ifequipped) a cupholder 4. Pen holder Use only soft cups in t...

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe battery from being discharged: • do not use the power point longer than necessary when the engine isnot running, • do not leave battery chargers, video ...

Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (to the first detent) andhold the switch to close. Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or bu...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controls(except for the driver’s) press theright side of the control. Press theleft side to restore the windowcontrols. Bounce-Back (Driver’s window only) When an obstacle has been detec...

To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Fold-away mirrors Pull the si...

• Press the bottom of the control to adjust the pedals towards you. The adjustment allows for approximately 2.8 inches (71 mm) ofmaximum travel. Never adjust the accelerator and brake pedal with feet on thepedals while the vehicle is moving. Memory feature (if equipped) The accelerator and brake ped...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or pressCNCL (Cancel). This will noterase your vehicle’s previously setspeed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set s...

In AM, FM1, or FM2 mode: • Press SEEK to access thenext/previous strong station. In Satellite radio mode (ifequipped): • Press and release SEEK to accessthe next/previous strong station. • Press and hold SEEK to fastadvance through preset channelsor subscribed channels. In CD mode: • Press SEEK to l...

SYNC system hands free controlfeature (if equipped) Press briefly to use the voice command feature. You will hear atone and LISTENING will appear inthe radio display. Press andhold to exit voice command. Press activate phone mode or answer a phone call. Press andhold to end call or exit phone mode.P...

U.S. federal safety standards (this includes any garage door openermodel manufactured before April 1, 1982). A garage door which cannotdetect an object, signaling the door to stop and reverse, does not meetcurrent U.S. federal safety standards. For more information, contactHomeLink 威 at: www.homelin...

• If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with “Programming” Steps 4 through6 to complete programming of a rolling code equipped device (most commonly a garage door opener). 4. At the garage door opener receiver (motor-head unit) in the garag...

• Proceed with Step 3 in the “Programming” section. Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office ...

MESSAGE CENTER With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status. Thesystem will also notify you...

1. To disable/enable the autolampdelay feature, select this functionfrom the SETUP control for thecurrent display mode. 2. Press the RESET control to selectthe new Autolamp delay values of 0,10, 20, 30, 60, 90, 120 or 180 seconds. Autolock (if equipped) This feature automatically locks all vehicle d...

OIL CHANGE REQUIRED/CHANGE OIL SOON. Displayed when the engine oil life remaining is 5 percent or less. When oil life left is between5% and 0%, the CHANGE OIL SOON message will be displayed. When oillife left reaches 0%, the OIL CHANGE REQUIRED message will bedisplayed. INTERIOR TRUNK CONTROL Press ...

CARGO AREA FEATURES Cargo net (if equipped) The cargo net secures lightweightobjects in the cargo area. Attach thenet to the anchors provided. Do notput more than 50 lb. (22 kg) in thenet. This net is not designed torestrain objects during a collision. 2008 Taurus (500) Owners Guide (post-2002-fmt)U...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and a remote keyless entrytransmitter. Your IKTs are programmed to your vehicle; using a non-programmed keywill not permit...

When inserting the IKT into theignition cylinder, place your thumbon the center thumb rest of the IKTand forefinger on the logo badge onthe opposite side. To gain more leverage when rotatingthe IKT in the ignition lock cylinder,you can readjust the location ofyour thumb to grasp the IKT on theouter ...

Smart locks This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open one of the front doors and you lock the vehicle with thepower door lock control (on the driver or passenger door trim panel), allthe doors will lock, then all doo...

Power door lock switch autolock enable/disable procedure Before starting, ensure the ignition is in the 1 (LOCK) position and allvehicle doors are closed. You must complete Steps 1–5 within 30 secondsor the procedure will have to be repeated. If the procedure needs to berepeated, wait a minimum of 3...

6. To enable/disable the autounlock feature, press the lock control, then pressthe unlock control. The horn will chirp once if autounlock was deactivated ortwice (one short and one long chirp) if autounlock was activated. 7. Turn the ignition to the 1 (LOCK) position. The horn will chirp onceto conf...

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the oper...

Opening the trunk Press twice within 3 seconds to open the trunk. • Ensure that the trunk is closed and latched before driving yourvehicle. Failure to properly latch the trunk may cause objects to fallout or block the driver’s rear view. Memory Seat Feature (if equipped) The Integrated Keyhead Trans...

Replacing the battery The Integrated Keyhead Transmitter uses one coin type three-voltlithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover. 2. Do not wipe off any grease on thebattery terminals ...

Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when theIntegrated Keyhead Transmitter or the keyless entry system keypad isused to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the 3 (RUN) position, ...

1. Place the key in the ignition andturn the ignition to the 3 (RUN)position. 2. Press the power door unlockcontrol on the door panel threetimes. 3. Turn the ignition from the 3(RUN) position to the 1 (LOCK)position. 4. Press the power door unlock control on the door panel three times. 5. Turn the i...

KEYLESS ENTRY SYSTEM You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • open the trunk. • recall memory seat/power mirrorspositions (if equipped). The keypad can be operated withthe factory set 5–digit entry code;this code is located on the owner’swallet card in...

Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personalcode. Erasing personal code 1. Enter the factory set 5–digit code.2. Within five seconds, press the 1 • 2 on the keypad a...

started unless a coded Integrated Keyhead Transmitter (IKT) programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded Integrated Keyhead Transmitters;additional coded IKTs may be purchased from your authorized dea...

The theft indicator will flash everytwo seconds to act as a theftdeterrent when the vehicle isarmed. Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the 3(RUN) position. The theft indicator will illuminate for three seconds and then go out. Ifthe theft indicat...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help protect your vehicle fromunauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL Integrated Keyhead Transmitters are brought to the authorized dealer to aid in troubleshooti...

• Press the 7 • 8 and 9 • 0 controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdownwhen any of the above actions occurbefore the vehicle becomes armed. Each door, the hood, and the trunkis armed individually, and if any areopen...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints To mi...

Push release button to lower headrestraint. Using the manual lumbar support (if equipped) The lumbar support control islocated on the outboard side of theseatback. Move the control up or down toadjust lumbar support. Folding down the front passenger seatback The front passenger seatback can befolded...

Cover sharp edges on the load to help prevent injury tooccupants. Secure the load to help prevent shifting during sudden stops. Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original...

Pull lever up to adjust seatback. Before returning theseatback to its original position, make sure that cargo orany objects are not trappedbehind the seatback. Afterreturning the seatback to itsoriginal position, pull on theseatback to ensure that it has fullylatched. An unlatched seat maybecome dan...

Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automaticpositioning of the driver seat, powermirrors, and adjustable pedals totwo programmable positions. The memory seat control is locatedon the driver door. • To program position 1, move thedriver seat, mirrors and ped...

The head restraints can be movedup by pulling up on the headrestraint. Push release button to lower headrestraint. Split-folding rear seat One or both rear seatbacks can be folded down to provide additionalcargo space. To lower the seatback(s) frominside the vehicle, pull the straplocated on the out...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

levels of crash severity and modify the deployment strategy of thedual-stage airbags and safety belt pretensioners. Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System™ totailor the deployment level of the driver dual-stage airbag based on seatposition....

Safety belt precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passe...

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movem...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recom...

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt andincrease the risk of injury in a collision. Safety belt pretensioner Your vehicle is equipped with safety ...

hardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collision be replaced. However, if the collision was minor and anauthorized dealer finds that the belts do not show damage and continueto operate properly, th...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rareevents” 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events,even for good drivers. 1 in 4 of us will be ser...

Do not sit on top of a buckled safety belt or insert a latchplateinto the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s air bag system. One time disable If at any time the driver/front passenger quickly buckles then unbucklesthe safety belt f...

2. Wait until the safety belt warning light turns off (Approximately 1minute). • Step 3 must be completed within 50 seconds after the safety beltwarning light turns off. 3. For the seating position being disabled, at a moderate speed, bucklethen unbuckle the safety belt nine times, ending in the unb...

outboard passenger from certain upper body injuries. The term“supplemental restraint” means the airbags are intended as a supplementto the safety belts. Airbags alone cannot protect as well as airbags plussafety belts in impacts for which the airbags are designed to deploy, andairbags do not offer a...

• Recline the seat slightly (one or two degrees) from the uprightposition. Do not put anything on or over the airbag module. Placingobjects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causingserious injury. Do not attempt to ser...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbaginflation. The fact that the airbagsdid not inflate in a collision does n...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS ...

The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects inthe front seat, • the system determines that an infant is present in a rear-facing infantseat that is installed according...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a back-up tone to indicate the condition of t...

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided. How does the side airbag system work? The design ...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, i...

If the Safety Canopy™system has deployed, the Safety Canopy™ will notfunction again unless replaced.The Safety Canopy™ system(including the A, B, and Cpillar trim) must be inspectedand serviced by an authorizeddealer. If the Safety Canopy™ is not replaced, the unrepaired areawill increase the risk o...

Important child restraint precautions You are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally children who are four years oldor younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, youmust put them in safety seats made especial...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol. All the LATCH lower anchors areequally spaced, so that a singleLATCH child seat can be installed atany rear seating position. If two child safety seats are installedusing the LATCH l...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tiregauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure. Note: If you o...

Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Built-in treadwearindicators, or “wear bars”, whichlook like narrow strips of smoothrubber across the tread will appearon the tire when the tread is worn...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If thebeads do not seat at the maximum pressure indicated, re-lubricate andtry again.When inflating the tire for m...

• Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over ...

4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You ...

Label or Tire Label which is located on the B-Pillar or the edge of thedriver’s door. The cold inflation pressure should never be set lower thanthe recommended pressure on the vehicle label. The tire suppliers may have additional markings, notes or warnings suchas standard load, radial tubeless, etc...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. The Tire Pressure Monitoring System is NOT a substitute formanually checking tire pressure. The tire press...

Low Tire PressureWarning Light Possible cause Customer Action Required Solid Warning Light Tire(s)under-inflated 1. Check your tire pressure toensure tires are properlyinflated; refer to Inflating your tires in this chapter. 2. After inflating your tires tothe manufacturer’srecommended inflationpres...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

How temperature affects your tire pressure The Tire Pressure Monitoring System (TPMS) monitors tire pressure ineach pneumatic tire. While driving in a normal manner, a typicalpassenger tire inflation pressure may increase approximately 2 to 4 psi(14 to 28 kPa) from a cold start situation. If the veh...

• Do not use tire chains, cables, or optional traction devices withoptional P225/55R18 tires. • Install cable chains securely, verifying that the cables do not touch anywiring, brake lines or fuel lines. • Drive cautiously. If you hear the cables rub or bang against yourvehicle, stop and re-tighten ...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • If you ...

STARTING Positions of the ignition 1. LOCK, locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessories off. 2. ACC, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. RUN, all electrical circuits oper...

• Make sure the gearshift lever is inP (Park). 3. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn t...

This vehicle has a computer assisted cranking system which assists instarting the engine. If the ignition key is turned to 4 (START) and thenreleased when the engine begins cranking, the engine may continuecranking for up to 10 seconds or until the vehicle starts. Guarding against exhaust fumes Carb...

with Outdoor Appliances. ⬙ Never use an indoor extension cord outdoors; it could result in an electric shock or fire hazard. • Use a 16 gauge outdoor extension cord, minimum. • Use as short an extension cord as possible. • Do not use multiple extension cords. Instead, use one extension cordwhich is ...

Make sure system is unplugged and properly stowed before driving thevehicle. While not in use, make sure the protective cover seals theprongs of the engine block heater cord plug. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, ...

Even when the ABS is disabled,normal braking is still effective. Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake systemserviced immediately. Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal...

Push the parking brake pedaldownward again to release theparking brake. Driving with theparking brake on will cause thebrakes to wear out quickly andreduce fuel economy. Note: If the vehicle is driven with the parking brake applied, a chimewill sound. ADVANCETRAC 姞 (ELECTRONIC STABILITY CONTROL) (IF...

All these conditions are normal during AdvanceTrac 威 operation. If the AdvaceTrac system is activated for an extended period of time, thebrake portion of the system will shut down to allow the brakes to cooldown. A limited AdvanceTrac 威 function using only engine power reduction will still help cont...

During Traction Control™ operation the engine will not “rev-up” whenyou push further on the accelerator. This is normal system behavior. If you should become stuck in deepsnow or on a very slippery roadsurface, try switching the TractionControl™ system off. This mayallow excess wheel spin to “dig” t...

Do not drive your vehicle until you verify that the brakelampsare working. Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the ...

D (Drive) with Overdrive The normal driving position for the best fuel economy. Transaxleoperates in gears one through six. D (Drive) with Overdrive Cancel and Grade Assist Pressing the transmission controlswitch on the side of the gearshiftlever activates two features at thesame time: Overdrive Can...

ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. With the AWD option, power will be delivered to the frontwheels and distributed to the rear wheels as needed. The AWD system isactive all the time and requires no input from the oper...

Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Even AWD vehicles can lose traction in slick mud. Aswhen you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until ...

Maintenance and Modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Customer Information Guidefor information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card a...

HAZARD FLASHER CONTROL The hazard flasher is located on theinstrument panel by the radio. Thehazard flashers will operate whenthe ignition is in any position or ifthe key is not in the ignition. Push in the flasher control and allfront and rear direction signals will flash. Press the flasher control...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located under the instrument panel to the left of thesteering wheel. The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 30A Smart window motor 2 15A Brake on/off switch, High-mountedbra...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 36 5A PATS module 37 10A Climate control 38 20A Subwoofer (Audiophile radio) 39 20A Radio 40 20A Spare 41 15A Mic mirror, Moon roof, Front lockswitches, Radio 42 10A Spare 43 10A Spare 44 10A Spare 45 5A Relay coils: PD...

Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longerfunction. Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increasedr...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability 3. Fu...

Stopping and securing the vehicle 1. Park on a level surface, set theparking brake and activate hazardflashers. 2. Place gearshift lever in P (Park)and turn engine off. Removing the spare tire and jack 1. Lift the trunk cargo cover, andremove the wing nut that securesthe spare tire by turning itcoun...

To help prevent the vehicle from moving when you change a tire,be sure to place the transaxle in P (Park), set the parking brake and block (in both directions) the wheel that is diagonally opposite(other side and end of the vehicle) to the tire being changed. If the vehicle slips off the jack, you o...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Take care toposition the jack as shown to ensurethat the locating holes in the jackbase can be placed on the locatingtabs of the jack mounting brack...

2. Place the tire, with the wheel facing downward, into the spare tirewell and secure the wheel with the large wing nut. If you are stowing the temporaryspare tire, place the tire over the jack and secure it with the largewing nut. WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the sp...

Note: Inspect the wheel pilot hole prior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean rag and apply grease.Apply grease only to the wheel pilothole surface by smearing a “dime”(1 square cm) sized glob of greasearound the wheel pilot sur...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect t...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, su...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

• For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassCleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the w...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean and damp white cotton cloth, then with a clean and dry whitecotton cloth; you may also use Motorcraft Dash & Vinyl Cleaner(ZC-38-A) on the instrument panel and interior tr...

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). In Canada, useMotorcraft Multi-Purpose Cleaner (CXC-101). • If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the rin...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood until the liftcylinders hol...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 ENGINE 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap ...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. Turn the bladeat a right angle to the arm. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wi...

5. Locate and carefully remove theengine oil level dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the...

• Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions,...

to the current engine and emission system protection standards and fueleconomy requirements of the International Lubricant Standardization andApproval Committee (ILSAC), comprised of U.S. and Japaneseautomobile manufacturers. To protect your engine’s warranty use Motorcraft SAE 5W-20 or anequivalent...

It is recommended that the negative battery cable terminal bedisconnected from the battery if you plan to store your vehicle for anextended period of time. This will minimize the discharge of your batteryduring storage. Note: Electrical or electronic accessories or components added tothe vehicle by ...

4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Release the parking brake. With your foot on the brake pedal and withthe A/C on, put the vehicle in D (Drive) and allow the engine to idle forat least one minute. 7. Drive...

60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -34°F (-36°C). • Boiling protection up to 265°F (129°C). • Protection against rust and other forms of corrosion. • Enables calibrated gauges to wo...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium GoldEngine Coolant since a Ford-approved recycling process is not yetavailable. Used engine coolant should be disposed of in an appropriate manner. ...

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cool...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

At the next opportunity, safely pull off of the road, remove the fuel fillercap, align the cap properly and reinstall it. The check fuel caplight or “check fuel cap” message may not reset immediately; it may take several driving cycles for the check fuel cap light or “check fuel cap” message to turn...

The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When refueling yourvehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the empty reserve still pres...

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to changea number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually gi...

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed: 15 minutes of steady driving on an ex...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...

If an overfill occurs, excess fluidshould be removed by an authorizeddealer. An overfill condition oftransmission fluid may cause shift and/or engagement concernsand/or possible damage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight cap...

A Accessory delay ..........................97AdvanceTrac ..............................227Air cleaner filter ...............310–311Air conditioning ....................76, 78Airbag supplemental restraintsystem ................162–163, 171, 173 and child safety seats ............164description ........

sidewall information ...............199snow tires and chains ............209spare tire .................................253terminology .............................190tire grades ...............................190treadwear ........................189, 194 Towing ........................................