Ford 2008 Escape Hybrid v.1- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

Neutral: It is not recommended to idle the vehicle in (N) Neutral for extended periods of time because this will discharge your high voltagebattery and decrease fuel economy. Also, the engine cannot providepower to the hybrid system in (N) Neutral. Low Gear: Low gear (L) is designed to mimic the enh...

battery charge level. You may also notice during extended downhilldriving that your engine continues to run instead of shutting off. During this “engine braking”, the engine stays on, but it’s not using anyfuel. You may also hear a slight whine or whistle when operating yourvehicle. This is the norm...

Frequently asked questions Question Answer What is the pumping sound I hearwhen I unlock or enter the vehicle,and the venting sound a fewminutes after shutting off myvehicle? This is the hydraulic portion ofyour regenerative braking systempressurizing and depressurizing.You may also hear it occasion...

Question Answer Can you charge the battery with aplug into an A/C outlet? There are no provisions forcharging the high voltage batteryfrom a power supply external tothe vehicle. What is the purpose of the ECONbutton? ECON mode may provideimproved fuel economy bypreventing the gasoline enginefrom run...

Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personalinjury. Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active ...

Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type,failur...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap: Illuminates when the fuel cap may not be properlyinstalled. Continued driving withthis ...

Airbag readiness: If this light fails to illuminate when ignition is turnedto the RUN position, continues toflash or remains on, have the systemserviced immediately by your authorized dealer. A chime will also soundwhen a malfunction in the supplemental restraint system has beendetected. Safety belt...

while ignition is in RUN. Always turn your ignition key to Off and removekey before leaving your vehicle. (The engine may be off when the vehicleis stopped, yet the key is on, and the engine can turn on at any time) Message center activation chime: Sounds when a warning message (except PARKING BRAKE...

AUDIO SYSTEMS AM/FM/single CD/in-dash CD6/MP3 satellite compatible soundsystem Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped)may be used for up to ten minutes after the ignition is turned off or untileither fr...

To activate, press MENU repeatedly until RDS (ON/OFF) appears in the display. Use SEEK/TRACK to toggle RDS ON/OFF. When RDS is OFF, you will not be able to search for RDS equipped stations orview the station name or type. To change categories: Press MENU until RDS ON appears in the display. Press CA...

14. ON/OFF/VOL (Volume): Press to turn ON/OFF. Turn toincrease/decrease volume. Note: If the volume is set above a certain level and the ignition isturned off, the volume will comeback on at a “nominal” listeninglevel when the ignition switch isturned back on. 15. SHUFFLE: In CD and MP3 mode, press ...

Auxiliary input jack Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers withhigh fidelity. To ...

6. Press AUX on the vehicle radio repeatedly until LINE IN appears inthe display.You should hear audio from your portable music player although it maybe low. 7. Adjust the sound on your portable music player until it reaches thelevel of the FM station or CD by switching back and forth between theAUX...

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thundersto...

Do not use any irregular shapedCDs or discs with a scratchprotection film attached. CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker r...

• Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result in anaudio mute. Unlike AM/FM audible static, you will hear an audio mute when there isa satellite radio signal interference. Your radio display may display NOSIGNAL to i...

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly. NO TEXT Category information not available. Category information not available at this time on this channel. The sy...

DUAL AUTOMATIC TEMPERATURE CONTROL 1. AUTO/Driver temperature: Press to engage full automatic operation. The system will automatically determine fan speed, airflowdistribution, A/C on or off, and outside or recirculated air, to heat or coolthe vehicle to reach the desired temperature. Turn to increa...

will automatically provide outside air to reduce window fogging. On dayswhere the outside temperature is approximately freezing or higher, theengine will run continuously in this mode. 5. Power/ : Press to activate/deactivate the climate control system. When the system is off, outside air is shut ou...

• Manual operation: 1. Select A/C. 2. Select or . 3. Select (recirculated air) to provide colder airflow. 4. Set the temperature to 60°F (16°C).5. Set highest fan setting initially, then adjust to maintain comfort. Make sure ECON mode is deactivated. To aid in side window defogging/demisting in cold...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the h...

High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the lowbeam headlamps on with a reduced output. To activate: • the i...

4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge of highintensity light towards the right. Ifthis edge is not at the horizontalreference line, the beam will need tobe adjusted. 5. Locate the vertical adjuster onthe headlamp, then use a 4 mmsocket to turn the ad...

The dome lamp control has threepositions: • OFF: In this position, the lampwill not illuminate. • DOOR: In this position, the domelamp will illuminate only when adoor is opened and will remainilluminated for 25 seconds afterthe door is shut. • ON: In this position, the lamp will remain illuminated. ...

Interior lighting battery saver The interior lamps will automatically extinguish after 10 minutes whenthe ignition key is in OFF/LOCK position, a door has been left open orthe interior lamp controls are in the ON position. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize p...

Replacing the interior bulbs Check the operation of all bulbs frequently. Replacing exterior bulbs Check the operation of all the bulbs frequently. Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. Reach over the front bolster. 4. Remove the...

3. Pull the bulb straight out of thesocket and push in the new bulb. To complete installation, follow theremoval procedure in reverse order. Replacing foglamp bulbs (if equipped) 1. Make sure the foglamp switch isin the OFF position. 2. From underneath the vehicle,remove the harness/bulb assemblyfro...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: INT 2 — Normal speed operation ofrear wiper. INT 1 — Intermittent operation ofrear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold a...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamps. CENTER CONSOLE Your vehicle is equipped with a variety of console features. Theseinclude: 1. Cupholders 2. Utility compartment console lidhas a CD holder, a business cardholder and two pen holders. Theutil...

Indicator light Code Green light is On — Power point is ready to supply power Green light is Off — Power point power supply is off. Ignition is not inRUN position Green light is blinking — Power point is in fault mode POWER WINDOWS Do not leave children unattended in the vehicle and do not letchildr...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press theright side of the control. Press theleft side to restore the windowcontrols. Accessory delay With accessory delay, the window switches, moon roof...

4. Press and hold the reset buttonon the compass module forapproximately 5 seconds until ZONEXX appears in the center stackdisplay. 5. Continue to press the reset button until the correct zone appears inthe center stack display. 6. The direction will display afterthe button is released. The zone isn...

EXTERIOR MIRRORS Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mirrors...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control. Turning off speed control There are two ways to turn off thespeed control: • Press the speed control OFFcontrol. • Turn OFF the ignition. Note: When you turn off the speed control or the ignition, your speed...

• To close, press and hold the front portion of the control until themoon roof comes to a complete stop then release the control. To operate the moon roof vent position: • To open, press and hold the front portion of the control. This willopen the vent. • To close, press and hold the rear portion of...

To reset the oil monitoring system to 100% after each oil change(approximately 10,000 miles [16,000 km] or 12 months) perform thefollowing: 1. Press and release the SETUPcontrol to display “OIL LIFE =XXX% HOLD RESET = NEW”. 2. Press and hold the RESETcontrol for 2 seconds and release.Oil life is set...

LOW TIRE PRESSURE. Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. TIRE PRESSURE MONITOR FAULT. Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on orcontinues t...

Make sure that the liftgate door and/or window are closed toprevent exhaust fumes from being drawn into the vehicle. Exhaust fumes contain carbon monoxide which can injure your lungsand cause drowsiness and even death. This will also preventpassengers and cargo from falling out. If you must drive wi...

LUGGAGE RACK Your vehicle is equipped with a roofrack. The maximum load for theroof rack is 100 lbs (44 kg), evenlydistributed on the cross-bars. If it isnot possible to evenly distribute theload, position it in the center or asfar forward on the cross-bars aspossible. Do not use the vehicle’s doorh...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and a remote keyless entrytransmitter. Your IKTs are programmed to your vehicle; using a non-programmed keywill not permit...

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Door key unlocking/locking Unlocking the doors Turn the key in the door cylinder to unlock the driver’s door only. Allother doors will remain locked. Locking the doors Turn the key in the door cylinder t...

Note: The autolock feature can be activated/deactivated independently of the autounlock feature. Before following the activation or deactivation procedures, make surethat the anti-theft system is not armed, ignition is in the 1 (OFF/LOCK)position, and all vehicle doors, liftgate and liftgate window ...

Message center procedure For information on activating/deactivating the autolock feature using thevehicle’s message center (if equipped), refer to Message center information in the Driver Controls chapter. Autounlock The autounlock feature will unlock all the doors when: • the ignition is in the 3 (...

2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirpone time to confi...

CHILDPROOF DOOR LOCKS When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoors are unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. NOTE: Setting the lock for on...

The typical operating range for yourIKT is approximately 33 feet(10 meters). A decrease inoperating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next toyour vehicle. The IKT allows you to: • remotely unlock the veh...

Switching from two step to one step door unlocking Unlocking can be switched between two step and one step doorunlocking by pressing and holding both and buttons simultaneously on the remote entry transmitter for approximately4 seconds. The turn signal will flash twice to indicate that the vehicle h...

To replace the battery: 1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing o...

Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when theIntegrated Keyhead Transmitter or the keyless entry system keypad isused to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the 3 (RUN) position, ...

vehicle or you can program the IKTs yourself. Refer to Programming spare Integrated Keyhead Transmitters for instructions on how to program the coded key. Note: The SecuriLock 娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems mayresult...

The theft indicator will illuminate for three seconds and then go out. Ifthe theft indicator stays on for an extended period of time or flashesrapidly, have the system serviced by your authorized dealer. Replacement Integrated Keyless Transmitters (IKT) and coded keys Note: Your vehicle comes equipp...

FRONT SEATS Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatbac...

Push side control and push down onhead restraint to lower it. Adjusting the front manual seat (if equipped) Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving...

Press to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Heated seats (if equipped) To operate the heated seats: • Push the button located on theinstrument panel to activate. • Push again to deactivate. The heated seats will activa...

The head restraints can be movedup and down. Lift the head restraintso that it is located directly or asclose as possible behind your head. Push control to lower or removehead restraint. Folding down rear seats 1. Raise the rear seat head restraintand remove. 2. Place the head restraint underthe fro...

3. Pull the seat release control. Note: Make sure the floor is clear of all objects before folding the seat. 4. Flip seat forward. Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught bystaying out of the seat back foldingpa...

2. Rotate seat cushion down into theseating position making sure thatthe seat cushion is locked into placeand that the safety belt buckles areexposed. Make sure safety belt buckleheads are through elastic holders on seat backs. Safety beltbuckles may break if they aretrapped underneath the seatbacka...

To remove the rear cushion 1. Lift the yellow tab to release thehinges. 2. Pull the cushion to the outboardside of the vehicle. To install the rear cushion 1. Push the cushion to the inboardside of the vehicle. 2. Make sure that the hinges arelocked into place. SAFETY RESTRAINTS Personal Safety Syst...

position. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower airbag output level. Front passenger sensing system For airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants th...

Safety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The...

movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph(8 km/h) or more, the combination safety belts will lock to help reduceforward movement of the driver and passengers. Automatic locking mode When to use the automati...

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive (emergency) locking mode. After any vehicle collision, the safety belt systems at all seatingpositions ...

authorized dealer finds that the belts do not show damage and continueto operate properly, they do not need to be replaced. Safety beltassemblies not in use during a collision should also be inspected andreplaced if either damage or improper operation is noted. Failure to inspect and if necessary re...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day. The more we drive, the more we areexposed to ⬙ rare ⬙ events, even for good drivers. 1 in 4 of us will b...

Reasons given... Consider... ⬙ I have an airbag ⬙ Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. ⬙ I’d rather be thrown clear ⬙ Not a good idea. People who are ejected are 40 times more likely toDIE. Safet...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of th...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The RCM (restraints control module) monitors its own internal circuitsand the supplemental airbag electrical system wiring (including theimpact sensors, the system wiring, the airbag system readiness light, theairbag back up power and the airbag ignitors). Several air bag system components get hot a...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the status of the system. Refer to Airbag readiness section ...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation.The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the s...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. Children and safety belts If the child is the pro...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly tilt the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward and back. Ther...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. You should become thoroughly familiar with thisinformation before you operate your vehicle. Do not become overconfident in the ability of 4WD and AWDvehicles. Although a 4WD or AWD vehicle may accelerate better than ...

At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall tires to the inflation pressure recommended by Ford Motor Company. Use a tire gauge to check the tire inflation pressure, including the spare(if equi...

To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile. If you are checking tire pressure when the tire is hot, (i.e. driven morethan 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires arehot from driving and it is norm...

cracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case it needs to be repaired or replaced. For your safety,tires that are damaged or show signs of excessive wear should not beused because they are...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If thebeads do not seat at the maximum pressure indicated, re-lubricate andtry again.When inflating the tire for m...

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystan...

Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly, providing better tire performance andlonger tire life. Unless otherwise specified, rotate the tires approximatelye...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the tire pressure readings to your vehicle. The LowTire Warning Lamp will turn ON if the tire pressure is significantly low.Once the light is illuminated, ...

Low TirePressure WarningLight Possible cause Customer Action Required Solid Warning Light Tire(s) under-inflated 1. Check your tire pressure toensure tires are properlyinflated; refer to Inflating your tires in this chapter. 2. After inflating your tires tothe manufacturer’srecommended inflation pre...

Low TirePressure WarningLight Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condit...

any tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecommended inflation pressure. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires o...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. D...

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) -(12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not haveenough cargo capacity to carry that much weight. In metric units, thecalculation would be: 635 kg - (2 x 9...

4WD GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum GCWR - lb. (kg) Trailer Weight Range - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 2.3L 4980 (2259) 1000 (454) 24 (2.2) Notes: For high altitude operation, reduce GCW by 2% per 1000 ft. (300 meters) elevation. For defi...

Safety chains Always connect the trailer’s safety chains to hook retainers on thevehicle. To connect the trailer’s safety chains, cross the chains under thetrailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agencygives to you. Do ...

Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance information for more information. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of ...

Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability, emissions and reliability. Replace the rear axle lubricant any time the axle has been submerged inwater. Rear axle lubricant quantities are not to be checked or ...

STARTING Positions of the ignition 1. LOCK, locks the gearshift leverand allows key removal. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the vehicle is notrunning. 3. RUN, all electrical circuitsoperational and warning lights willilluminate. This is the position ...

resetting of the fuel pump/high voltage shut-off switches or service. Forinformation on jump starting the vehicle and resetting the fuelpump/high voltage shut-off switches, refer to the Jump starting your vehicle (low voltage [underhood] battery only) section, the Jump starting the high voltage batt...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. (I...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

Utility vehicles and trucks have larger tires and increased groundclearance, giving the vehicle a higher center of gravity than a passengercar. Vehicles with a higher center of gravity such as utility vehiclesand trucks handle differently than vehicles with a lower center of gravity. Utility vehicle...

N (Neutral) With the gearshift lever in N (Neutral), the vehicle is free to roll; holdthe brake pedal down while in this position. Because of the uniquenature of the hybrid vehicle, the engine will not start in the N (Neutral)position. The vehicle does not charge the high voltage battery in the N (N...

REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when R (Reverse) is selected and thevehicle is moving at speeds less than 3 mph (5 km/h). The system is noteffective at speeds above 3 mph (5 km/h) and may not dete...

FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) For important information regarding safe operation of this typeof vehicle, see Preparing to drive your vehicle in this chapter. Your vehicle is equipped with an intelligent 4WD System thatcontinuously monitors vehicle conditions and automatically adjusts t...

If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, and ease the vehicle back onto thepavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surfac...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your authorized dealer. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable e...

Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required from another vehicle. Remember, you may be able to backout the way you came if you proceed with caution. Mud and water If you must drive through highwa...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills . A danger lies in losing traction, sli...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Customer Information Guidefor information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card a...

HAZARD FLASHER CONTROL The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the...

If you see or smell fuel, do not reset the fuel pump shut-off or try tostart your vehicle; you could injure yourself or others. Have all thepassengers get out of the vehicle and call the local fire department or atowing service. FUSES AND RELAYS Fuses If electrical components in thevehicle are not w...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 45 5A Front wiper logic, Blower motorrelay 46 7.5A OCS (restraints), PADI (restraints) 47 30A Circuit Breaker Power windows, Moon roof 48 — Delayed accessory relay Power distribution box The power distribution box is lo...

Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare is in use. To restore the full functionality ofthe TPMS system, all road wheels equipped with the tire pressuremonitoring sensors must be mounted on the vehicle. Have a flat tire serviced by an authorized...

When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one...

• Front View shown from rear of front tire.Position the jack directly below theprotruding bolt. 2008 Escape Hybrid (ehv) Owners Guide (post-2002-fmt)USA (fus) Roadside Emergencies 219

• Rear View shown from forward of reartire. Position the jack directly belowthe stud on the rear trailing arm. 3. Position the jack according to theguides and turn the jack handleclockwise until the tire is amaximum of 1 inch (25 mm) off theground. Never use the differentials as ajacking point. To l...

4. Slide the wheel partially under the vehicle and install the retainerthrough the center of the wheel.5. Turn the jack handle clockwise until the tire is raised to its originalposition underneath the vehicle. The effort to turn the jack handleincreases significantly as the tire contacts the frame. ...

JUMP STARTING (LOW VOLTAGE [UNDERHOOD] BATTERYONLY) Your vehicle has two separate jump starting procedures; the followingprocedure is for the low voltage (underhood) battery only. Refer to Jump starting the high voltage battery in this chapter for information on jump starting the high voltage batter...

5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to design...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

The high voltage battery contains potassium hydroxide (a strongalkaline electrolyte) which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your vehicle. This vehicle does nothave push-start capability. If you attempt to start your vehicle and the engine cranks but does n...

Jump starting your vehicle (Low voltage [underhood] battery only) section in this chapter for information on jump starting the low voltage(underhood) battery. You may perform another high voltage battery jumpstart by pressing the jump start button after having connected thejumper cables and starting...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

Additional Assistance If you still have a complaint involving a warranty dispute, you may wishto contact the Better Business Bureau (BBB) AUTO LINE program (U.S.only). In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford...

You can get more information by calling BBB AUTO LINE at1–800–955–5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any t...

You may purchase Ford ESP from any participating authorized dealer.There are several plans available in various time, distance and deductiblecombinations which can be tailored to fit your own driving needs. FordESP also offers reimbursement benefits for towing and rental coverage. When you buy Ford ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent quality product to help protect from environmentaleffects. WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist ...

• To remove tar and grease, use Motorcraft Bug and Tar Remover(ZC-42), available from your authorized dealer. ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engi...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). • For plastic...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean and damp white cotton cloth, then with a clean and dry whitecotton cloth; you may also use Motorcraft Dash & Vinyl Cleaner(ZC-38-A) on the instrument panel and interior tr...

• If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). • If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the ring will set. • Do not use household cleaning products or gl...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

1. High voltage connector shield 2. Service Disconnect 3. High voltage battery case Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P(Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpect...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. At the front of the vehicle, lift upon the auxiliary latch handle locatedin the center between the hood andthe grille. 3. Lift the hood open and secure itwith the prop rod. 2008 Es...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Motor/Electronics (M/E) coolant reservoir 3. Engine oil filler cap 4. Brake fluid reservoir 5. Power distribution box 6. Low Voltage (underhood) battery 7. Engine air filter assembly 8. Engine oil dipstick...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use anyspecial washer fluid such as windshield water repellent type fluid or bugwash. They may cause s...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. Turn the bladeat a right angle to the arm. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wi...

Changing rear window wiper blade The rear wiper arm is designed without a service position. This reducesthe risk of damage to the blade in an automatic car wash. To replace the wiper blade: 1. Grab the wiper arm just belowthe blade attachment and pull it asfar away from the glass as possible.Do not ...

5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within the MIN and MAX marks or the lower andupper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is b...

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above theFULL mark on the en...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. Low and high voltage battery – storage Your vehicle must be started and run for a minimu...

ENGINE COOLANT AND MOTOR/ELECTRONICS COOLANT Your vehicle is equipped with two separate coolant systems. One is forengine cooling and the other is for various electric motors and othercomponents that are specific to the hybrid operating systems. Checking engine coolant The concentration and level of...

Checking motor/electronics (M/E) coolant The M/E coolant reservoir is locatedbehind the engine coolant reservoir.Refer to the following enginecoolant sections for all information,instructions and warnings related tocooling systems. The two systemsuse the same coolant and operatesimilarly, with the M...

If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not u...

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion...

necessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak...

• NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine damage. • Decreased engine coolant concentrations below 40% willdecrease the freeze protection cha...

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce st...

2. Carefully turn the filler cap counterclockwise until it spins off. 3. To install the cap, align the lugs on the cap with the threads on thefiller pipe. 4. Turn the filler cap clockwise until it clicks at least once. After refueling, if the “CHECK FUEL CAP” indicator comes on and stayson when you ...

Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the Right Fuel section. Running out of fuel Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have ru...

For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling;an error in the reading will result if the engine is left running. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rat...

Note: The brake system on this vehicle can only be bled at a authorized dealer. TRANSMISSION FLUID Checking electronically controlled continuously variabletransmission (eCVT) Refer to your scheduled maintenance information chapter for scheduled intervals for fluid checks and changes. Your transaxle ...

7. The fluid level should be within1/4 inch (6 mm) of the plug threads. 8. Replace the check plug. Adjusting eCVT fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is indicated in the Maintenance product specifications and capacities section in this chap...

Changing the air filter element 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halvesof the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to remove any dirt ordebris and ...

Changing the high voltage battery air filter element 1. Remove access panel located inthe rear cargo area on the driver’sside trim panel to expose the filtercover. 2. Push the tabs (located on eachside of filter cover) while pullinggently to remove filter cover. 3. Install new filter and filter cove...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Not all accessories are available for all models. For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight capacity of the v...

GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for yourvehicle. Carefully following this schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay also help to increase the value of ...

Ford strongly recommends the use of genuine Ford replacement parts.Parts other than Ford, Motorcraft or Ford authorized remanufacturedparts that are used for maintenance replacement or for the service ofcomponents affecting emission control must be equivalent to genuineFord Motor Company parts in pe...

Get the most from your service and maintenance visits There are a lot of reasons why visiting your Ford or Lincoln MercuryDealership for all your service needs is a great way to help keep yourvehicle running great. Convenience Many Dealerships have extended evening and Saturday hours to makeyour ser...

and Motorcraft branded parts meet these specifications. You can findthem at your Ford and Lincoln Mercury Dealership. Look for thefollowing brand logos to ensure the parts installed on your vehicle meetFord Motor Company Specifications. Genuine Ford and Motorcraft Replacement Parts Ford and Lincoln ...

Multi-point Inspection In order to keep your vehicle running right, it is important that you havethe systems on your vehicle checked regularly. This can help identify anypotential issue before there are any problems. Ford Motor Companysuggests the following multi-point inspection to be performed at ...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) intervals with exceptionsnoted. ADDITIONAL INFORMATION AVAILABLE ON THE WEB To learn more about the importance of routine and dealer-performedmaintenan...

SPECIAL OPERATING CONDITIONS Towing a trailer or using a camper or car-top carrier Every 5,000 miles, 6 months or 200 hours of engine operation (whichever comes first) Change engine oil and replace filter Every 5,000 miles Inspect tires and rotate Extensive Idling and/or Low Speed Driving for Long D...

Special Operating Conditions Log D EALER V ALIDATION : RO#: P&A C ODE : D ATE : M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE : M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE : M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE : M ILEAGE : D EALER V ALIDATION...

A Accessory delay ..........................61 Air cleaner filter ...............279–282 Air conditioning automatic temperaturecontrol system ..........................39 Airbag supplementalrestraint system ........119, 128, 131 and child safety seats ............121description ..............119, 12...

Towing .......................................175 recreational towing .................180trailer towing ..........................175wrecker ....................................231 Transmission .............................189 brake-shift interlock (BSI) ....189fluid, checking and adding(automatic)...