Ford 2007 Fusion v.1- User Manual

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

authority. Other parties may seek to access the informationindependently of Ford Motor Company and Ford of Canada. Cell phone use The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

indicate whether the vehicle is ready for Inspection/Maintenance (I/M)testing. Normally, the ⬙ Check Engine ⬙ light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, ifafter 15 seconds the ⬙ Check Engine ⬙ light blinks eight times, it means that ...

Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehiclechecked by your authorized dealer. Anti-lock brake system (ifequipped): If the ABS light stays illuminated or co...

Low fuel (if equipped): Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is engaged. Turnsoff when the speed control systemis disengaged. Door ajar (if equipped): Illuminates when the ignition ...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMS Quick start — How to get going Listening to the radio 1. If the audio system is off, pressVOL-PUSH to turn the radio on.Turn VOL-PUSH to adjust thevolume. Note: The system may take a few moments to turn on. 2. Press AM/FM repeatedly tochoose between AM/FM1/FM2frequency bands. 3. Press ...

2. Press AUX repeatedly to cyclethrough auxiliary audio sources.Select SAT1, SAT2 or SAT3 to listento satellite radio. 3. Press SEEK, SEEK to access the previous or next satellitechannel. You may also seek by musiccategory. For further information, refer to CATEGORY listing under the MENU control on...

For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot number usingmemory presets 1–6. When thedisplay reads LOAD CD#, load thedesired disc, label side up. If you do not choose a slot within 5 seconds,the system will choose for you. Once loaded, the first track will ...

CD SHUF will appear in the display.To disengage, press SHUFFLE again. SHUFFLE OFF will appear in thedisplay. Note: In track mode, all tracks on the current disc will shuffle in random order. In MP3 folder mode, the system will randomly play alltracks within the current folder. Press / (play/pause) w...

FADE: Press MENU to reach the fade setting. Use / to adjust the audio between the back (B) and front (F) speakers. SPEEDVOL (Speed sensitive volume, if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louderwith increasing vehicle speed to compensate for road and ...

5. SEEK : In radio mode, press / to access the previous/next strong station. In CD mode , press / to access the previous/next CD track. In satellite radio mode (if equipped), press SEEK, SEEK to seek to the previous/next channel. If a specific category is selected,(Jazz, Rock, News, etc.), press SEE...

10. FF (Fast forward): Press FF to manually advance in a CD/MP3track. 11. REW (Rewind): Press REW to manually reverse in a CD/MP3 track. 12. Memory presets: To set a station, select the desired frequencyband, AM, FM1 or FM2. Tune to thedesired station. Press and hold a preset button until sound retu...

17. LOAD: To load a disc into the system, press LOAD. Select a slotnumber using memory presets 1–6.When the display reads LOAD CD#,load the desired disc, label side up.If you do not choose a slot within 5 seconds, the system will choose foryou. Once loaded, the first track will begin to play. To aut...

Auxiliary input jack (if equipped) Your vehicle may be equipped withan Auxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers with...

Troubleshooting: 1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are notcompatible with the AIJ. The AIJ will only work correctly with devicesthat have a headphone output with a volume control. 2. Do not set the portab...

CD/CD player care Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleanerand wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circula...

• Creating discs with only one level of folders will help with navigationthrough the disc files. Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other t...

• Antenna obstructions: For optimal reception performance, keep theantenna clear of snow and ice build-up and keep luggage and othermaterial as far away from the antenna as possible. • Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage...

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly. NO TEXT Category information not available. Category information not available at this time on this channel. The sy...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop. AUTOMATIC TEMPERATURE CONTROL (ATC) SYSTEM(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center, ...

• To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of theheadlam...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. INTERIOR LAMPS Dome lamps and map lamps The map lamps are located on theoverhead console. Press the controlsto turn on the lamps. Your vehicle may also have readinglamps within the rear dome ...

9. Tuck the 2 lead wires into the lamp housing to assure that they arenot pinched when installing the protective rubber cap. 10. Install the protective cap/grill to the housing circular ring by pushingand pressing it forward. 11. Re-apply pressure around the complete circular ring on the housingto m...

Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb tobreak the next time the headlamps are operated. 12. After the new bulb is installed, carefully let the bulb sock...

Replacing foglamp bulbs (if equipped) 1. Make sure the foglamp switch isin the OFF position. 2. From underneath the vehicle,partially remove the tire splashshield by removing four drivescrews. After removing to allow free accessto the front fog lamp bulb andelectrical wire harness, the splash shield...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is set on the intermittent settings, the speed of the wipers will automatically ...

TILT/TELESCOPE STEERING WHEEL To adjust the steering wheel: 1. Pull the lever down to unlock thesteering column. 2. While the lever is in the downposition, move the steering wheelup or down and in or out until youfind the desired position. 3. While holding the steering wheelin place, pull the lever ...

CLOCK (IF EQUIPPED) Press the right (+) control to movethe time display forwards. Press the left (-) control to movethe time display backwards. INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may beused to secure sunglasses or similarsized objects. Press the control toopen the storage c...

To prevent the battery from being discharged, do not use the powerpoint longer than necessary when the engine is not running. Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lightersocke...

EXTERIOR MIRRORS Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mirrors...

Turning off speed control There are two ways to turn off the speed control: • Press the speed control OFFcontrol. • Turn OFF the ignition. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control feat...

In any mode: • Press VOL + or - to adjust thevolume. Climate control features Press TEMP + or - to adjusttemperature. Press FAN + or - to adjust fanspeed. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up(from the closed position) to ventilate the vehicle....

To open the moon roof: The moon roof is equipped with anautomatic, one-touch, expressopening, closing and venting feature.Press and release the rear portion ofthe control. To stop motion at anytime during the one-touchoperation, press the control asecond time. When closing the moon roof, you should ...

• To close the moon roof from the vent position, press and hold the rearportion of the control until the glass panel stops moving. The moon roof has a sliding shade that can be opened or closed whenthe glass panel is shut. To close the shade, pull it toward the front of thevehicle Accessory delay: W...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and a remote keyless entrytransmitter. Your IKTs are programmed to your vehicle; using a non-programmed keywill not permit...

Before starting, ensure the ignition is in the 1 (LOCK) position and allvehicle doors are closed. You must complete Steps 1–5 within 30 secondsor the procedure will have to be repeated. If the procedure needs to berepeated, wait a minimum of 30 seconds before beginning again. 1. Place the key in the...

• the vehicle has then come to a stop and the ignition is turned to the 1(LOCK) or 2 (ACC) position; and • the driver door is opened within 10 minutes of the ignition beingtransitioned to the 1 (LOCK) or 2 (ACC) position. Note: The doors will not autounlock if the vehicle has been electronically loc...

To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The handle iscomposed of a material that willglow for hours in darkness followingbrief exposure to ambient light. The “T” shaped handle will belocated eith...

Replacing the battery The Integrated Keyhead Transmitter uses one coin type three-voltlithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover. 2. Do not wipe off any grease on thebattery terminals ...

Illuminated entry The interior lamps and puddle lamps (if equipped) illuminate when theIntegrated Keyhead Transmitter is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the 3 (RUN) position, or • the Integrated Keyhead Transm...

1. Place the key in the ignition andturn the ignition to the 3 (RUN)position. 2. Press the power door unlockcontrol on the door panel threetimes. 3. Turn the ignition from the 3(RUN) position to the 1 (LOCK)position. 4. Press the power door unlock control on the door panel three times. 5. Turn the i...

SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock 娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded Integrated Keyhead Transmitter (IKT) programmed to your vehicle is used. The use of the wrong type of ...

Automatic arming The vehicle is armed immediately after switching the ignition to the1 (LOCK) position. The theft indicator will flash everytwo seconds to act as a theftdeterrent when the vehicle isarmed. Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the3 (R...

If the key was not successfully programmed, it will not start yourvehicle’s engine and/or will not operate the remote entry features. Thetheft indicator light may flash on and off. Wait 20 seconds and you mayrepeat Steps 1 through 8. If failure repeats, bring your vehicle to yourauthorized dealer to...

Each door, the hood or the trunk is armed individually, and if any areopen, they must be closed for the system to enter the 20 secondcountdown. The turn signal lamps will flash once when all doors, the hood and thetrunk are closed indicating the vehicle is locked and entering the 20second countdown....

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Using the manual lumbar support (if equipped) The lumbar control is located on theside of the seat cushion. Turn to adjust lumbar support. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upri...

Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation. Pull lever up to adjust seatback. Folding down the front passenger seatback (if equipped) The front passenger seatback can be folded to a horizontal position tomake room for a long load. To fold...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

Move the switch in the direction ofthe arrows to raise or lower thefront portion of the seat cushion. Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion. Press the switch in the direction ofthe arrows to move the seatforward, backward, up or down. Hea...

to the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the airbag. For otheroccupants, this occurs when the occupant is not properly restrained bysafety belts or child safety seats and they move forward during pre-crashbraking. The mo...

Front safety belt energy management retractors The front outboard safety belt energy management retractors allowwebbing to be pulled out of the retractor in a gradual and controlledmanner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occup...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag supplemental restraint system (S...

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movem...

This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children12 years old and under should be properly restrained in the rear seatwhenever possible. Refer to Safety restraints for children or Safety seats for children lat...

hardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collision be replaced. However, if the collision was minor and anauthorized dealer finds that the belts do not show damage and continueto operate properly, th...

If... Then... The driver’s or front passenger’ssafety belt becomes unbuckled forapproximately 1 minute while thevehicle is traveling at least 3 mph(5 km/h) and more than 1-2 minuteshave elapsed since the ignitionswitch has been turned to ON... The BeltMinder 威 feature is activated - the safety belt ...

National Highway Traffic Safety Administration (NHTSA)recommends a minimum distance of at least 10 inches (25 cm) between an occupant’s chest and the driver airbag module. Never place your arm over the airbag module as a deployingairbag can result in serious arm fractures or other injuries. Steps yo...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• and the electrical wiring which connects the components • Side curtain airbag system. Refer to Side curtain airbag system later in this chapter. • Front passenger sensing system. Refer to Front passenger sensing system. later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator...

• a child or a small person occupies the front passenger seat and thechild or small person is unbuckled. The front passenger sensing systemuses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind youthat the front passenger frontalairbag is disabl...

In case there is a problem with thefront passenger sensing system, theairbag readiness light in theinstrument cluster will stay lit. If the airbag readiness light is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenge...

A difficulty with the system is indicated by one or more of the following: • The readiness light (same lightfor front and side airbag system)will either flash or stay lit. • The readiness light will notilluminate immediately after ignition is turned on. • A series of five beeps will be heard. The to...

If the side airbag hasdeployed, the airbag will not function again. The sideairbag system (including theseat) must be inspected andserviced by an authorizeddealer. If the airbag is not replaced, the unrepaired area willincrease the risk of injury in acollision. Determining if the system is operation...

Side curtain airbag system Do not place objects ormount equipment on or near the headliner at the siderailthat may come into contact with adeploying side air curtain. Failureto follow these instructions mayincrease the risk of personal injuryin the event of a collision. Do not place objects or mount...

How does the side air curtain system work? The design and development of theside air curtain system includedrecommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the ris...

The side air curtain system SRS is designed to activate when the vehiclesustains lateral deceleration sufficient to cause the sensors to close anelectrical circuit that initiates air curtain and seat-mounted side airbaginflation.The fact that the side air curtain and seat-mounted side airbag did not...

If any of these things happen, even intermittently, have the SRS servicedat an authorized dealer immediately. Unless serviced, the system may notfunction properly in the event of a collision. Disposal of airbags and airbag equipped vehicles(including pretensioners) See your authorized dealer. Airbag...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tiregauge onto the valve and measure the pressure with the tire gauge. 3. Add enough air to reach the recommended air pres...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Highway hazards No matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly to theclosest safe area out of traffic. This may further damage the flat tire, butyour safety is more important. If you feel a sudden vibration or rid...

• Front Wheel Drive (FWD)/ AllWheel Drive vehicles (front tiresat top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem i...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. Follow these guidelines when us...

Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, oroptional equipment. Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipme...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2007 Fusion (fsn) Owners Guide (post-2002-fmt)US...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Do not exceed the GVWR or the GAWR specified on the SafetyCompliance Certification Label. Do not use replacement tires with lower load carrying capacitiesthan the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than theoriginals do not ...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fol...

STARTING Positions of the ignition 1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and all electricalaccessories off without locking thesteering wheel. To lock the steeringwheel, remove the key then turn thesteering wheel. 2. ACC, allow...

Starting the engine 1. Turn the key to 3 (RUN) withoutturning the key to 4 (START). 2. Turn the key to 4 (START), thenrelease the key as soon as theengine starts. Excessive crankingcould damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to LOCK...

Parking brake To set the parking brake (1), pullthe parking brake handle up as faras possible. The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released. To release, press and hold the button (2), pull the handle up slightly,then push the handle down. Always...

Aggressive driving in any road conditions can cause you to losecontrol of your vehicle increasing the risk of severe personal injury or property damage. The occurrence of a Traction Control 娂 event is an indication that at least some of the tires have exceededtheir ability to grip the road; this may...

To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transaxle has a starter interlock that prevents cranking theengine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put t...

Recommended upshifts (for best fuel economy) when accelerating 3 - 4 32 mph (51 km/h) 4 - 5 44 mph (71 km/h) Reverse 1. Make sure that your vehicle is at a complete stop before you shift intoR (Reverse). Failure to do so may damage the transmission. 2. Hold the clutch pedal down and move the gearshi...

If your vehicle is equipped with AWD, a spare tire of a different sizeother than the tire provided should never be used. A dissimilar spare tiresize (other than the spare tire provided) or major dissimilar tire sizesbetween the front and rear axles could cause the AWD system to stopfunctioning and d...

• In the event of an emergency stop, avoid skidding the tires and do notattempt any sharp steering wheel movements. • If the vehicle goes from one type of surface to another (i.e., fromconcrete to gravel) there will be a change in the way the vehicleresponds to a maneuver (steering, acceleration or ...

when you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until you regain control of the vehicle. If the engine or transmission is submerged in water, their fluids shouldbe checked and changed, if necess...

as adding or removing parts (such as lift kits or stabilizer bars) or byusing replacement parts not equivalent to the original factory equipment. Any modifications to a vehicle that raise the center of gravity can makeit more likely the vehicle will rollover as a result of a loss of control.Ford Mot...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwn...

to turn them off. Use it when your vehicle is disabled and is creating asafety hazard for other motorists. Note: With extended use, the flasher may run down your battery. FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a sub...

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wiredamage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link ca...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electri...

• Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocatio...

• Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving veh...

2. Remove the center ornament (ifequipped) from the wheel. Looseneach wheel lug nut one-half turncounterclockwise but do not removethem until the wheel is raised offthe ground. 3. Put the jack in the jack locatornext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is compl...

7. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torquespecification. 8. Unblock the wheels. Stowing the wheel and jack 1. Fully collapse the jack and place it back in the storage area in the...

When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc thatcontacts the wheel. Ensure that any fasteners that attach the rotor tothe hub are secured so they do not interf...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect t...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

Additional Assistance If you still have a complaint involving a warranty dispute, you may wishto contact the Better Business Bureau (BBB) AUTO LINE program (U.S.only). In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford...

You can get more information by calling BBB AUTO LINE at1–800–955–5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any t...

You may purchase Ford ESP from any participating authorized dealer.There are several plans available in various time, distance and deductiblecombinations which can be tailored to fit your own driving needs. FordESP also offers reimbursement benefits for towing and rental coverage. When you buy Ford ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

• 3.0L DOHC engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use ...

may cause squeaking or chatter noise from the blades, and streaking andsmearing of the windshield. To clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned witha non-abrasive cleaner such as Motorcraft Ultra-Clear Spray GlassCleaner (ZC-23), available f...

INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then with a clean, drycloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A). • Do not use household or glass cleaners as these may damage thefinish. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equi...

leather conditioners. These products may cause premature wearing ofthe clear, protective coating. Note: In some instances, color or dye transfer can occur when wet clothing comes in contact with leather upholstery. If this occurs, theleather should be cleaned immediately to avoid permanent staining....

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Owner Informat...

2. Block the wheels. To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake/Clutch fluid reservoir 5. Transmission fluid dipstick (if equipped) 6. Battery 7. Power distribution box 8. Air filter assembly 9. Coolant bleed valve ...

3.0L DOHC V6 Duratec engine 1. Engine coolant reservoir 2. Power steering fluid reservoir 3. Brake fluid reservoir 4. Transmission Fluid Dipstick 5. Battery 6. Power distribution box 7. Air filter assembly 8. Coolant bleed valve 9. Engine oil dipstick 10. Engine oil filler cap 11. Windshield washer ...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has man...

• 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter....

• 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. On 2.3L...

5. Fully install the engine oil filler cap by turning the filler cap clockwiseuntil it stops. To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed. Engine oil and filter recommendations Look for this certificationtrademark...

that does not meet Ford material and design specifications, start-upengine noises or knock may be experienced. It is recommended you usethe appropriate Motorcraft oil filter (or another brand meeting Fordspecifications) for your engine application. BATTERY Your vehicle is equipped with aMotorcraft m...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, maydarken the color of Motorcraft Premium Gold Engine Coolant fromyellow to golden tan. Note: When adding more than 1 quart (.95L) of coolant it is necessary to use the coolant...

Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium Gold...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

1. Pull off the road as soon as safely possible and turn off the engine.2. Arrange for the vehicle to be taken to an authorized dealer.3. If this is not possible, wait a short period for the engine to cool.4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while ...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If...

If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine. On restarting, cranking time will take a few seconds longerthan normal. • Normally, adding one gallon of fuel is enough ...

• Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump a...

The engine must warm up to its normal operating temperature. Oncestarted, do not turn off the engine until the above driving cycle iscomplete. If the vehicle is still not ready for I/M testing, the abovedriving cycle will have to be repeated. POWER STEERING FLUID Refer to scheduled maintenance infor...

1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right severaltimes. 3. Turn the engine off. 4. Check...

High fluid level Fluid levels above the safe rangemay result in transaxle failure. Anoverfill condition of transmissionfluid may cause shift and/orengagement concerns and/orpossible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Bef...

Checking and adding manual transmission fluid (if equipped) 1. Park the vehicle on a levelsurface. 2. Engage the parking brake fully –put in first gear. 3. Ensure the vehicle cannot move. 4. Clean the filler plug. 5. Remove the filler plug andinspect the fluid level. 6. Fluid level should be at bott...

Changing the air filter element • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. • 2.3L I4 engine 2007 Fusion (fsn) Owners Guide (post-2002-fmt)USA (fus) Maintenance and Spec...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Mobile-Ease 娂 hands free communication system Remote start Vehicle security systems Wheel locks Not all accessories are available for all models. For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding a...

A Accessory delay ..........................68 Air cleaner filter ...............262–264 Air conditioning ....................43, 45 Airbag supplementalrestraint system ........121, 130, 133 and child safety seats ............123description ..............121, 130, 133disposal ..........................

checking the pressure ............152inflating ...................................150label .........................................162replacing ..................................154rotating ....................................156safety practices .......................155sidewall information .........