Ford 2007 Freestyle v.1- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

• where the driver was positioning the steering wheel. To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or wher...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Check fuel cap (if equipped): Illuminates when the fuel cap maynot be properly installed. Continueddriving with this light on may causethe Check engine warning light tocome on, refer to Fuel filler cap in the Maintenance and Specification chapter. Brake system warning light: To confirm the brake sys...

Speed control: Illuminates when the speed control is engaged. Turnsoff when the speed control systemis disengaged. Low washer fluid (if equipped): Illuminates when the windshieldwasher fluid is low. Door ajar (if equipped): Illuminates when the ignition is inthe ON position and any door ordecklid is...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMS AM/FM stereo/ single CD Satellite Compatible sound system(if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches and radio may be used for up to tenminutes after the ignition switch is turned off or until either front door is...

2. Phone/mute: Press to mute the playing media. Press again to returnto the playing media. 3. Menu: Press to toggle through the following modes: CATEGORY (Satellite Radio if equipped): Press MENU until the currently active category appears in the display (CATEGORY MODE). InCATEGORY MODE, press / to ...

17. CD: Press to enter CD mode. If a CD is already loaded into thesystem, CD play will begin where itended last. 18. LOAD: Press to load a CD. Press LOAD and a memory presetto load to a specific slot. Press andhold to autoload up to six CDs. 19. CD eject: Press to eject a CD. Press and hold to auto ...

Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12cm) audio compact discs only. Due to technical incompatibility,certain recordable and re-recordable compact discs may n...

• Station overload: When you pass a ground based broadcast repeatingtower, a stronger signal may overtake a weaker one and result in anaudio mute. Unlike AM/FM audible static, you will hear an audio mute when there isa satellite radio signal interference. Your radio display may display NOSIGNAL to i...

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly. NO TEXT Category information not available. Category information not available at this time on this channel. The sy...

FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a Family Entertainment DVD Systemwhich allows you to play commercial DVDs, CDs and also most CD R/W,DVD R/W, VCD, and MP3 media. You can also plug in and play auxiliarymedia devices such as video game systems and MP3 pla...

4. ENTER control Press to select the function highlighted on the active menu. ENTER mayalso be used by some user interactive discs during movie play. 5. MENU control Press to bring up the disc menu. 6. AUX control Press to switch DVD player from play mode to auxiliary mode. 7. Auxiliary jacks Input ...

Remote control 1. REV (REVERSE) control Press to reverse the direction of the DVD movie. 2. FWD (FORWARD) control Press to advance the direction of the DVD movie. 3. PLAY/STOP control When playing, press PLAY/STOP to stop the disc. When stopped, pressPLAY/STOP to play the disc. 4. SEEK control Press...

• Always save MP3 files with the .mp3 extension. The player recognizesan MP3 file by the .mp3 extension, so MP3 files saved with differentextensions will not be played. Never save a non-MP3 file with the.mp3 extension as the file will not play properly. • The player supports multi session discs. How...

On-screen indicators Each time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible indicators: 1. DVD/ CD STATUS (PLAY/FWD/REV/PAUSE) 2. CD track number / DVD title 3. DVD chapter number 4. MEDIA COUNTER — displays current viewing tim...

The front glass on the flip-down liquid crystal display (LCD) maybreak when hit with a hard surface. If the glass breaks, do not touch the liquid crystalline material. In case of contact with skin, washimmediately with soap and water. Do not expose the flip-down liquid crystal display (LCD) to direc...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/decrease the airflow...

Dual Zone Automatic Temperature Control with heated seats(if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/de...

Dual Zone Automatic Temperature Control with rear passengercompartment climate control (if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Rear temperature cont...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan to the highest speed. 5. Direct the outer instrument panel vents towards the side windows. Do not place objects on top of the instrument panel a...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamp switch to . The headlamps will turn off. Foglamp control (if equipped) With the ignition on, the foglampscan be turned on when theheadlamp control is pulled towardyou and is in any of the foll...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF, autolamps or parking lampposition and • the transmission must be out of the Park position. Always remember to turn on ...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control up oneposition. Adjust the rotary control to thedesired speed setting. Mist function: To activate mist, push control down from the OFFposition and release to get one wipe. For normal or low speed wiperoperation, move con...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: 2 — Three to four second intervalrear wiper. 1 — Ten second interval rear wiper. O — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) ...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamp. The visor willslide back and forth on the rod forincreased sunlight coverage. Slide on rod feature Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage. Note: To st...

Storage compartment Press the latch to open the storagecompartment. The door will openslightly and can be moved to fullopen. The storage compartment may beused to secure sunglasses or asimilar object. Conversation mirror (if equipped) The conversation mirror allows the driver to view the rear seatin...

Second row center console features (if equipped) The second row center consoleincorporates the following features: • Utility compartment • Cupholders • Flip forward armrest to provide aflat load floor Use only soft cups in thecupholder. Hard objects can injure you in a collision. AUXILIARY POWER POI...

Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromits heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by yourwarranty. POWER WINDOWS Do not leave child...

To operate ONE TOUCH UP: • Pull the switch completely up tothe second detent and releasequickly. The driver’s window willclose fully. Momentarily press theswitch to any position to stop theone touch up. If the switch is pressed and held tothe normal open or ONE TOUCH DOWN position during a ONE TOUCH...

Accessory delay With accessory delay, the radio, Family Entertainment DVD System (ifequipped), power windows, and moonroof (if equipped) operate for upto ten minutes after the ignition switch is turned from the ON to theOFF position or until one of the front doors are opened. AUTOMATIC DIMMING INSID...

Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a ...

Memory feature (if equipped) The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features when a memory position is selected through theremote entry transmitter, keyless entry keypad or memory switch on thedriver’s...

STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features • Press MEDIA to select AM, FM1,FM2, or CD (if equipped). In Radio mode: • Press SEEK to access thenext/previous strong station. In CD mode: • Press SEEK to listen to the nexttrack on the disc. In any mode: • Press VOL up or down to adjust...

MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up toventilate the vehicle. Do not let children play with the moon roof or leave childrenunattended in the vehicle. They may seriously hurt themselves. To open the moon roof: The moon roof is equipped with ana...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a convenient way toreplace up to three hand-heldtransmitters with a single built-indevice. This feature will learn theradio frequency codes of mosttransmitters to operate g...

7. Press and release the “learn” or “smart” button. (The name and colorof the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLink 威 button. Repeat the press/hold/release sequ...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status. Thesystem will a...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for severalseconds. The message center will display th...

PASSENGER DOOR AJAR. Displayed when the passenger side door is not completely closed. LEFT REAR DOOR AJAR. Displayed when the left rear door is not completely closed. RIGHT REAR DOOR AJAR. Displayed when the right rear door is not completely closed. PARK BRAKE ENGAGED. Displayed when the park brake ...

To reset the oil monitoring system to 100% after each oil change[approximately 5,000 miles (8,000 km) or 180 days] perform thefollowing: To reset the oil life to 100% with system warnings CHANGE OILSOON/OIL CHANGE REQUIRED displayed: 1. Select this function from theSETUP control for current displaym...

3. Press and hold RESET controlagain until OIL LIFE SET TO 100%is displayed. Your oil life is nowreset. LIFTGATE Unlock the liftgate (but do notrelease it) with the power door locksystem and remote entrytransmitter. To open the liftgate, pull the liftgatehandle rearward. • Do not open the liftgate i...

To adjust the cross-bar (if equipped) position: 1. Loosen the thumbwheel at bothends of the cross-bar. 2. Slide the cross-bar to the desiredlocation. 3. Tighten the thumbwheel at bothends of the cross-bar. Use adjustable tie down loops to secure the load. 2007 Freestyle (219) Owners Guide (post-2002...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

CHILDPROOF DOOR LOCKS • Move control up to engage thechildproof lock. • Move control down to disengagechildproof lock. The childproof locks are located on rear edge of each rear door and mustbe set separately for each door. Setting the lock for one door will notautomatically set the lock for both do...

and the turn lamps will flash once if all the doors and liftgate are closed.If any door or the liftgate is not closed, or if the hood is not closed invehicles equipped with the perimeter alarm feature, the horn will chirptwice and the lamps will not flash. Sounding a panic alarm Press to activate th...

Note: If your vehicle is equipped with the memory seats/power mirrors/adjustable pedals feature, you can associate a remote entrytransmitter to each memory position using this procedure. The firsttransmitter that is programmed will recall Driver 1 settings, and thesecond transmitter that is programm...

Illuminated entry The interior lamps illuminate when the remote entry system or thekeyless entry system keypad (if equipped) is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the 3 (RUN) position, or • the remote transmitter...

KEYLESS ENTRY SYSTEM You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • activate or deactivate theautolock feature. The keypad can be operated withthe factory set 5–digit entry code;this code is located on the owner’swallet card in the glove box, ismarked on the...

Your vehicle comes with two coded keys; additional coded keys may bepurchased from your authorized dealer. The authorized dealer canprogram your spare keys to your vehicle or you can program the keysyourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The...

Automatic disarming The vehicle is disarmed immediately after the ignition is turned from the1 (LOCK) to the 3 (RUN) position. The theft indicator will illuminate for three seconds and then go out. If the theft indicator stays on for an extended period of time or flashesrapidly, have the system serv...

3. Turn the ignition to the 1 (LOCK) position and remove the first coded key from the ignition. 4. Within ten seconds of turning the ignition to the 1 (LOCK) position,insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.Kee...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter. • Unlock the doors by using your keyless entry pad. • Unlock the driver’s door with a key. Turn the key full forward (towardthe front of the vehicle) to make sur...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Push release button to lower headrestraint. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Lift handle to move seat forward orbackward. ...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

The indicator light on the control will illuminate when activated. For lowheat, one light will be lit; for high heat, both lights will be lit. The heating of the seat turns off after 10 minutes or when the vehicle isturned off. Memory seats/power mirrors/adjustable pedals (if equipped) This system a...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

To return the seatback to theupright position • Lift the seatback toward the rearof the vehicle, and • Rotate the seatback until youhear a click, locking it in theupright position. Note: The seatback will not raise if the rear latch hooks are notproperly engaged to the floorstriker. • Pull the head ...

Stowing the third row bench or split bench seat (if equipped) 1. Stow the head restraints bypushing the head restraint releasebuttons while sliding the headrestraints fully down. Remove allobjects from the seat and stowagetub. 2. From the rear of the vehicle, fold seatback by pulling and holding the...

Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System 娂 to tailor the deployment level of the driver dual-stage airbag based on seatposition. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower air...

Safety belt precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passe...

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movem...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recom...

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt andincrease the risk of injury in a collision. Safety belt pretensioner Your vehicle is equipped with safety ...

assemblies, buckle support assemblies (slide bar-if equipped), shoulderbelt height adjusters (if equipped), shoulder belt guide on seatback (ifequipped), child safety seat LATCH and tether anchors, and attachinghardware, should be inspected after a collision. Ford Motor Companyrecommends that all sa...

BeltMinder 姞 The BeltMinder 威 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders byintermittently sounding a chime and illuminating the safety belt warninglight in the instrument cluster when the driver’s and front passenger’ssafety belt...

If... Then... The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately 1minute while the vehicle istraveling at least 3 mph (5km/h) and more than 1-2minutes have elapsed since theignition switch has been turnedto ON... The BeltMinder 威 feature is activated - the safety belt wa...

Reasons given... Consider... “Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many when no other vehicles are around. “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’t...

• This will enable the BeltMinder 威 feature for that seating position if it is currently disabled. As confirmation, the safety belt warning light willflash 4 times per second for 3 seconds, followed by 3 seconds with thelight off, then followed by the safety belt warning light flashing 4 timesper se...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. Do not place any object between an occupant and an airbag orne...

• Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to s...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbaginflation. The fact that the airbagsdid not inflate in a collision does n...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS ...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided. How does the side airbag system work? The design ...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, i...

Do not attempt to service, repair, or modify the Safety Canopy 娂 system, its fuses, the A, B, C or D pillar trim, or the headliner on a vehicle containing a Safety Canopy 娂 . See your authorized dealer. All occupants of the vehicle including the driver should alwayswear their safety belts even when ...

If the Safety Canopy 娂 system has deployed, the Safety Canopy 娂 will not function again unless replaced. The Safety Canopy 娂 system (including the A, B, C, and D pillar trim) must be inspected and serviced by an authorized dealer. If the Safety Canopy 娂 is not replaced, the unrepaired area will incr...

require that children use approved booster seats until they are eightyears old. Check your local and state or provincial laws for specificrequirements regarding the safety of children in your vehicle. Whenpossible, always place children under age 12 in the rear seat of yourvehicle. Accident statisti...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward. There should ...

Rear seating positions Follow Steps 1–7 as described above for the following available seats: • 2nd row bucket (40/40) • 2nd row bench (60/40) • 3rd row bench Note : The cargo tie-downs at the rear edge of the floor are nottether anchors. For additional important safety information on the proper use...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Built-in treadwearindicators, or “wear bars”, whichlook like narrow strips of smoothrubber across the tread will appearon the tire when the tread is worn...

2000 the numbers go to four digits. For example, 2501 means the 25thweek of 2001. The numbers in between are identification codes used fortraceability. This information is used to contact customers if a tire defectrequires a recall. Tire Replacement Requirements Your vehicle is equipped with tires d...

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. It is recommended that the two front tires or two rear tires generally bereplaced as a pair. Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe pos...

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel ali...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h)...

11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label, which is located on the B-Pillar or the edge of thedriver’s door, for the correct tire pressure for your vehicle. 12. Treadwear, Traction and Tempe...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. Follow these guidelines when using snow tires and chains: • Use only SAE class “S” cables or equivalent on the front axle forP215/65R17 equipped...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

calculation would be: 635 kg — (2 x 99 kg) — (12 x 45 kg) = 635 —198 — 540 = —103 kg. You will need to reduce the load weight by atleast 240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags,then the load calculation would be: 1400 – (2 x 220) – (9 x 100) = 1400 – 440 – 900 = 60 lb. Now youh...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourauthorized dealer or trailer rental agency for proper instructions andequipment for hooking up trailer lamps. Driving while you tow When tow...

RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a recreational vehicle ormoving truck). In case of roadside emergency with a disabled vehicle, please refer to the Wrecker towing section in the Driving chapter...

STARTING Positions of the ignition 1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and all electricalaccessories off without locking thesteering wheel. To lock the steeringwheel, remove the key then turn thesteering wheel. 2. ACC, allow...

• Make sure the gearshift lever is inP (Park). 3. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn t...

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If ...

keeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking and thebrake pedal may suddenly travel a little farther as soon as ABS braking isdone and normal brake operation resumes. These are normalcharacteristics of the ABS and should b...

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released. Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park). The parking brake is not recommended to stop a mo...

The Traction Control 娂 system will allow your vehicle to make better use of available traction on slippery surfaces. The system is a driver aidwhich makes your vehicle easier to handle primarily on snow and icecovered roads. During Traction Control 娂 operation the engine will not “rev-up” when you p...

• Do not fill the power steering pump reservoir above the maximumlevel, as this may result in leaks from the reservoir. See Checking and adding power steering fluid in the Maintenance and Specifications chapter. If the power steering system breaks down (or if the engine is turnedoff), you can steer ...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this p...

Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normal detection zone of the RSS system may create false beeps. The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners o...

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. W...

Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required from another vehicle. Remember, you may be able to backout the way you came if you proceed with caution. Mud and water If you must drive through high w...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slip...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER CONTROL The hazard flasher is located on theinstrument panel by the radio. Thehazard flashers will operate whenthe ignition is in any position or ifthe key is not in the ignition. Push in the flasher control and allfront and rear direction signals will flash. Press the flasher control...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel/Smart Junction Box (SJB) The fuse panel is located under the instrument panel to the left of thesteering wheel. The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F1 20A High beams F2 15A Interior lamps (C...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F8 15A Park lamps, Side markers, Trailertow protect F9 20A Cigar lighter, Data Link Connector(DLC) F10 7.5A Mirrors and memory module,SDARS F11 20A Audio, Family EntertainmentSystem (FES) F12 10A Back-up lamps, Electroc...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F22 7.5A Auxiliary climate control relaycoils, Electrochromatic mirror,Compass module F23 7.5A Wiper relay coil, Blower relay coil,Cluster logic F24 7.5A Occupant Classification Sensor(OCS), Passenger AirbagDeactivation...

• Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance •...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

Tire change procedure 1. Park on a level surface, activatehazard flashers and set the parkingbrake. When one of the front wheels is off the ground, the transaxlealone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park). To help prevent the vehicle fr...

4. Insert the straight end of the jackretention bracket through the eyeletof the angled bracket and swing theretention bracket over the jack. Withthe jack in place, place the end ofthe retention bracket over thethreaded stud in the trunk floor andsecure it with the plastic wing nut. If you are stowi...

1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on b...

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s eng...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

Additional Assistance If you still have a complaint involving a warranty dispute, you may wishto contact the Better Business Bureau (BBB) AUTO LINE program (U.S.only). In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford...

You can get more information by calling BBB AUTO LINE at1–800–955–5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any t...

You may purchase Ford ESP from any participating authorized dealer.There are several plans available in various time, distance and deductiblecombinations which can be tailored to fit your own driving needs. FordESP also offers reimbursement benefits for towing and rental coverage. When you buy Ford ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellan...

Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination of the airbag system. • Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoi...

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over theleather. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleaner (ZC-11–A). Dry the area with a soft cloth. • To help maintain its resiliency and color, use the Motorcraft DeluxeLe...

SERVICE RECOMMENDATIONS To help you service your vehicle we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Owner Informati...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood and support it withthe prop...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from the vehicle slightly. 2. Press the release button and pull the wiper blade from the wiper arm. 3. Attach the new wiper to the wiper arm by sliding it onto the wiperarm until it clicks into place. Replace wiper blades at least once per year fo...

5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the indicator back in an...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot. Steam andscalding liquid...

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come outforcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When...

9. Install the thermostat housingbleed plug. Install metal pin bypushing into the slot. After any coolant has been added, check the coolant concentration, referto the Checking engine coolant section. If the concentration is not 50/50 (protection to –34° F [–36° C]), drain some coolant and adjust the...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications...

FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif...

• Automotive fuels can be harmful or fatal if swallowed. Fuel such asgasoline is highly toxic and if swallowed can cause death or permanentinjury. If fuel is swallowed, call a physician immediately, even if nosymptoms are immediately apparent. The toxic effects of fuel may notbe visible for hours. •...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel mayspray out and injure you or others. If you do not use the proper fuel filler cap, excessive vacuum inth...

If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine. On restarting, cranking time will take a few seconds longerthan normal. • Normally, adding one gallon of fuel is enough ...

• Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump a...

These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly tightening the fuel cap. After threedriving cycles without these or any other temporary malfunctionspresent, the indicator should turn off—A driving cycle consists of a cold engine startup fo...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

TRANSAXLE FLUID Checking automatic transaxle fluid—CVT transaxle Do not use supplemental transaxle fluid additives, treatments orcleaning agents. The use of these materials or transaxle fluidsother than the recommended fluid, may affect transaxle operationand result in damage to internal transaxle c...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehiclethrough your local Ford or Ford of Canada dealer. These quality accessorieshave been specifically engineered to fulfill your automotive needs; they arecustom designed to complement th...

A Accessory delay ..........................74 Air cleaner filter .......................281 Air conditioning ........48, 50, 52, 54 Airbag supplemental restraintsystem ................140–141, 149, 151 and child safety seats ............142description ..............141, 149, 151disposal ..............