Ford 2007 Focus v.1- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

• how far (if at all) the driver was depressing the accelerator and/or thebrake pedal; • how fast the vehicle was traveling; and • where the driver was positioning the steering wheel. To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

converter. Drive in a moderate fashion (avoid heavy acceleration anddeceleration) and have your vehicle serviced immediately by yourauthorized dealer. Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or oth...

Airbag readiness: If this light fails to illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately by your authorized dealer. A chime will also sound when amalfunction in the supplemental restraint system has been detected. Safety belt: Reminds you...

Traction Control 娂 system (if equipped): Illuminates when the Traction Control 娂 is turned OFF and will flash when active. If thelight remains on, have the systemserviced immediately, refer to the Driving chapter for more information. Low fuel: Illuminates when the fuel level in the fuel tank is at ...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range. If it enters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, s...

AUDIO SYSTEMS AM/FM stereo with single CD — Premium (if equipped) AM/FM stereo with single CD/MP3 — Premium (if equipped) 2007 Focus (foc) Owners Guide (post-2002-fmt)USA (fus) Entertainment Systems 16

Speed sensitive volume: Radio volume automatically adjusts according to vehicle speed to compensate for road and wind noise. Press the Tune selector ( / ) or SEEK to turn off or select rates 1 through 7. Rate 7 compensates the most volume at higher speeds. Setting the clock: Upon initial battery con...

16. ON/OFF/Volume: Press to turn ON/OFF; turn to increase/decreasethe volume levels. If the volume isset above a certain level and theignition is turned off, for at least aminute, the volume will come backon at a “nominal” listening level when the ignition switch is turned backon. 17. CD: Press to e...

• Station overload: When you pass a broadcast tower, a stronger signalmay overtake a weaker one and play while the weak station frequencyis displayed. CD/CD player care Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approve...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Air flow selections: Controls the direction of the airflow in thecabin. See the following for a briefdescription on each control. : Distributes air through the instrument panel vents. : Distributes air through the instrument panel vents and the floorvents. : Distri...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents toward the side windows. To increase airflow to the outer instrument panel vents, clos...

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice andfog. • A small LED will illuminate whenthe rear defroster is activated. The ignition must be in the ONposition to operate the rear window defr...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on when the headlampcontrol is in the or the po...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF or parking lamp position and • the parking brake must be disengaged. Always remember to turn on your headlamps at dusk ...

Replacing headlamp bulbs 1. Make sure the headlamp controlis in the OFF position and open thehood. 2. Pull off the bulb cap. 3. Twist off the bulb retainer ring byturning it counterclockwise. 4. Pull the bulb straight out. Install in reverse order. Handle a halogen headlamp bulb carefully and keep o...

Replacing side marker bulbs 1. Make sure the headlamp controlis in the OFF position. 2. Remove the front shield from thebumper. 3. Reach under the front fender,grasp the bulb socket and turn itcounterclockwise to remove it. 4. Pull the bulb straight out. Install in reverse order. Replacing high-moun...

MULTI-FUNCTION LEVER Windshield wiper: Move the lever down for a single wipe. For intermittent operation, movecontrol up one position and adjustthe rotary control to the desiredspeed. For normal operation, move controlup two positions. For high speed operation, move control up three positions. Mist ...

TILT AND TELESCOPE STEERING COLUMN (IF EQUIPPED) Pull the locking lever down to adjustand telescope the steering columnposition. Return the lever to itsoriginal position to secure thewheel. The telescope function is adjustedby moving the wheel toward thedriver to telescope out and towardthe instrume...

Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers: • Place the VELCRO 威 hook onto the side of the aftermarkettransmitter opposite of thebutton. • Place the transmitter into storagecompartment, button down...

Window lock The window lock feature allows onlythe driver and front passenger tooperate the power windows. To lock out all the rear windowcontrols slide the control to the left.Slide the control to the right torestore the window controls. EXTERIOR MIRRORS Power side view mirrors (if equipped) To adj...

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h)or more without keeping your foot on the accelerator pedal. Speedcontrol does not work at speeds below 30 mph (48 km/h). Do not use the speed control in heavy traffic or on roads thatare winding, slippery...

STEERING WHEEL CONTROLS (IF EQUIPPED) Remote audio steering column controls (if equipped) The remote audio steering column controls may be used to select radioor CD mode. The following functions can be carried out using the remotecontrol. • Volume: Pull VOL + towards the steering wheel to increase t...

Bounce back: When an obstacle has been detected in the moon roof opening as themoon roof is closing, the moon roof will automatically open and stop at aprescribed position. Bounce back override: To override bounce back, press and hold the front portion of the control.For example: Bounce back can be ...

Wagon Pull out the roller cover and securethe retaining points. The cover canbe removed completely by pressinginward on both ends of the support. To reduce the risk of injury,the luggage cover must be properly attached to the mountingclips. Do not place any objects on the cargo area cover. They mayo...

Make sure that the liftgate door is closed to prevent exhaustfumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with theliftgate door open, keep the vents open so outside air comes into thevehicle. LUGGAGE RACK (IF EQUIPPED) The m...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency.Your keys are coded to your vehicle; using a non-coded key will notpermit your vehicle to start. If you lose your dealer supplied keys,replacement keys ...

5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmittershould operate normally after battery replacement. Replacing lost remote entry transmitters If you would like to have your remo...

SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock 娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start...

Replacing coded keys can be very costly. Store an extra programmed keyaway from the vehicle in a safe place to help prevent anyinconveniences. Please visit an authorized dealer to purchase additionalspare or replacement keys. Programming spare keys You can program your own coded keys to your vehicle...

10. Turn the ignition from the 2 (OFF) position to the 3 (ON) position.Keep the ignition in the 3 (ON) position for at least one second, but nomore than 10 seconds.11. Your new, unprogrammed key is now programmed.If the key has been successfully programmed it will start the vehicle’sengine and the t...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Adjusting the front manual seat Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury ordeath in a crash. Always sit upright against your seatback, with y...

Lift the control to adjust the angleof the seatback. Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Heated seats (if equipped) The heated seats switch is located on the center console. To operate t...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

• The warning light will either flash or stay lit. • The warning light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and warning light are repaired. If any of these things happen, even in...

The front outboard and rear safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatsafety belts have two types of locking modes. Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing freeshoulder belt length adjustm...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recom...

Three door models are equippedwith a safety belt parking feature forthe driver and front passenger. Thepurpose of the parking feature is toallow the driver or passenger toreach the safety belt. Fasten yoursafety belt as normal, and the beltwill slide to the front of the steelbar along the bottom of ...

Do not use extensions to change the fit of the shoulder beltacross the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All saf...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The supplemental restraint system is designed to work with the safetybelt to help protect the driver and right front passenger from certainupper body injuries. Airbags DO NOT inflate slowly or gently, and the risk of injury from a deploying airbag is the gr...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• Front passenger sensing system. Refer to Front passenger sensing system. later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system. later in this chapter. • a readiness light and tone. • diagnostic module. • and the electrical wiri...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

A difficulty with the system is indicated by one or more of the following: • The readiness light (same lightfor front and side airbag system)will either flash or stay lit. • The readiness light will notilluminate immediately after ignition is turned on. • A series of five beeps will be heard. The to...

How does the side airbag system work? The side airbag system consists ofthe following: • An inflatable nylon bag (airbag)with a gas generator concealedbehind the outboard bolster ofthe driver and front passengerseatbacks. • A special seat cover designed toallow airbag deployment. • The same warning ...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the side airbag hasdeployed, the airbag will not function again. The sideairbag system (including theseat) must be inspected andserviced by an authorizeddealer. If the airbag is not replaced, the unrepair...

Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather, they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Important child restraint precautions You are required by law to use safety restraints for children in...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulderbelt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk ...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position with LATCH andtether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

• On Sedan’s the anchors arelocated on the rear back panel. • For 3–door/5–door and Wagon,the anchors are located on theback of the rear seat. 4. On a sedan, open the tetheranchor cover. 5. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat ...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Built-in treadwearindicators, or “wear bars”, whichlook like narrow strips of smoothrubber across the tread will appearon the tire when the tread is worn...

built. For example, the numbers 317 mean the 31st week of 1997. After2000 the numbers go to four digits. For example, 2501 means the 25thweek of 2001. The numbers in between are identification codes used fortraceability. This information is used to contact customers if a tire defectrequires a recall...

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. It is recommended that the two front tires or two rear tires generally bereplaced as a pair. Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe pos...

Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by an authorized dealer.Front wheel drive (FWD) vehicles and those with an independent rearsuspension (if equipped) may require alignment of all four wheels. The tires should also be...

5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in your Owne...

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load can be carried by the tire. This pressure isnormally higher than the manufacturer’s recommended cold inflationpressure which can be found on the Saf...

If you choose to install snow tires on your vehicle, they must be thesame size, construction, and load range as the original tires listed on thetire placard, and they must be installed on all four wheels. Mixing tires ofdifferent size or construction on your vehicle can adversely affect yourvehicle’...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

1400 – (2 x 220) – (9 x 100) = 1400 – 440 – 900 = 60 lb. Now youhave the load capacity to transport the cement and your friend home.In metric units, the calculation would be: 635 kg — (2 x 99 kg) — (9x 45 kg) = 635 — 198 — 405 = 32 kg. The above calculations also assume that the loads are positioned...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourauthorized dealer or trailer rental agency for proper instructions andequipment for hooking up trailer lamps. Driving while you tow When tow...

RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as behind arecreational vehicle). These guidelines are designed to ensure that your transmission is notdamaged due to insufficient lubrication. All Front W...

STARTING Positions of the ignition 1. LOCK, locks the steering wheel,automatic transaxle gearshift leverand allows key removal. 2. OFF, shuts the engine and allelectrical accessories off withoutlocking the steering wheel. 3. ON, all electrical circuitsoperational. Warning lightsilluminated. Key posi...

If starting a vehicle with a manualtransaxle: 1. Make sure the parking brake isset. 2. Push the clutch pedal to the floor. • Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for mo...

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.5 cm) or a...

Four-wheel anti-lock brake system (ABS) (if equipped) Your vehicle may be equipped with an Anti-lock Braking System (ABS).This system helps you maintain steering control during emergency stopsby keeping the brakes from locking. Noise from the ABS pump motorand brake pedal pulsation may be observed d...

The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released. To release, press and hold the button (2), pull the handle up slightly,then push the handle down. Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (a...

The Traction Control 娂 switch is located on the center console, bythe gearshift lever. The TractionControl 娂 system will automatically turn on every time the ignition isturned off and on. If you should become stuck in snowor ice or on a very slippery road surface, try switching the TractionControl 娂...

• loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steeringseem to wander/pull. AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevent...

2 (Second) This position allows for second gear only. • Provides engine braking. • Use to start-up on slippery roads. • To return to D (Overdrive), move the gearshift lever into the D(Overdrive) position. • Selecting 2 (Second) at higher speeds will cause the transaxle todownshift to second gear at ...

To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral position. 3. Start the engine, then press the brake pedal and release the parkingbrake. 4. Move the gearshift lever to the desired gear, then slowly r...

Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Fully apply the parking brake, then shift into 1 (First). 3. Turn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Rem...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER CONTROL The hazard flasher is locatedbetween the center air registersabove the radio. The hazard flasherswill operate whether the ignition isoff or on. Push in the flasher control and allfront and rear direction signals will flash. Press the flasher control againto turn them off. Use ...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 56 20A Front wipers 57 7.5A Radio and cluster (accessory) 58 — Not used 59 7.5A Light switch (headlamps) 60 7.5A Air bag module 61 7.5A PATS modules, Instrument cluster 62 7.5A Radio (Start) 63 20A Power locks (GEM) Fus...

To remove a fuse, use the fuse puller tool provided on the powerdistribution box cover. The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 40A Main power supply (to passengercompartment fuse panel) 2 — Not used 3 — Not used 4 30A Air...

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (...

11. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nuttorque specification. 12. Put flat tire, jack and lug wrenchaway. Make sure the jack is fastenedso it does not rattle when you drive.Unblock t...

JUMP STARTING The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your automatic transmissionv...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party mediation/arbitration program administered by the CanadianMotor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relat...

For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide French Owner...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as g...

When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser ...

hot wax treatments used by commercial car washes, water repellantcoatings, tree sap, or other organic contamination; these contaminantsmay cause squeaking or chatter noise from the blades, and streaking andsmearing of the windshield. To clean these items, follow these tips: • The windshield, rear wi...

INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then with a clean, drycloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A). • Do not use household or glass cleaners as these may damage thefinish. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equi...

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleather conditioners. These products may cause premature wearing ofthe clear, protective coating. Note: In some instances, color or dye transfer can occur w...

SERVICE RECOMMENDATIONS To help you service your vehicle we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Owner Informati...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. To reduce the risk of vehicle damage and/or person...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L/2.3L I4 Engines 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil filler cap 4. Brake/Clutch fluid reservoir 5. Power distribution box 6. Battery 7. Automatic transaxle fluid dipstick (if equipped) 8. Engine oil dipst...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has man...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Change your engine oil and filter according to the appropriate schedulelisted in scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material and ...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, maydarken the color of Motorcraft Premium Gold Engine Coolant fromyellow to golden tan. • Do not add/mix an orange-colored, extended life coolant suchas Motorcraft Specialty Or...

3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the “COLD FILL RANGE” or the “FULL COLD” lev...

Severe climates If you drive in extremely cold climates (less than –34° F [–36° C ]): • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection c...

FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif...

• Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking materials away from fuel; • Stay outside your vehicle and do not leave the fuel pump unattendedwhen refueling your vehicle — this is against the law in some places; • Keep children away from the fuel pum...

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel mayspray out and injure you or others. If you do not use the proper fuel filler cap, excessive vacuum inth...

If you have run out of fuel: • You may need to cycle the ignition from off to on several times afterrefueling, to allow the fuel system to pump the fuel from the tank tothe engine. • The indicator may come on. For more information on the “check engine” or the “service engine soon” indicator, refer t...

• Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up. • Have the vehicle loading and distribution the same every time. Your results w...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If the indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may no...

The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the performance of you...

If an overfill occurs, excess fluidshould be removed by an authorizeddealer. An overfill condition oftransmission fluid may causeshift and/or engagementconcerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may ...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Air cleaner filter .......................204 Airbag supplemental restraintsystem ....................................83, 92 and child safety seats ..............85description ..........................83, 92disposal ......................................94driver airbag ........................85,...