Ford 2007 Five Hundred v.2- User Manual

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap (if equipped): Illuminates when the fuel cap maynot be properly installed. Continueddriv...

Low fuel (if equipped): Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is engaged. Turnsoff when the speed control systemis disengaged. Low washer fluid (if equipped): Illuminates when the wi...

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedriver’s door is opened. GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At norma...

AUDIO SYSTEMS AM/FM stereo/ single CD Satellite Compatible Sound System(if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches and radio may be used for up to tenminutes after the ignition is turned off or either front door is opened. 1. /...

3. Menu: Press to toggle through the following modes: Setting the clock: Press MENU until SELECT HOUR or SELECT MINS is displayed. Use / / SEEK to manually increase/decrease. Press MENU again to disengage clock mode. If your vehicle is equipped with an in-dash clock, refer to Clock in the Driver Con...

2. Phone/mute: Press to mute the playing media. Press again to returnto the playing media. 3. Menu: Press to toggle through the following modes: Setting the clock: Press MENU until SELECT HOUR or SELECT MINS is displayed. Press / / SEEK to adjust the hours/minutes. Press MENU again to disengage cloc...

18. LOAD: Press to load a CD. Press LOAD and a memory presetto load to a specific slot. Press andhold to autoload up to six CDs. 19. CD eject: Press to eject a CD. Press and hold to auto eject all CDspresent in the system. If there is noCD present, the display will read NO CD. 20. CD slot: Insert a ...

CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re-recordable compactdiscs may not function correctly when used in Ford CD players.Irregular shaped CDs, CDs with a scratch protection filmattached, and...

DVD player controls 1. MAIN control • NEXT — Press to access the next track on the CD, the next chapteron the DVD, or to go up in cursor mode. • PREV — Press to access the previous track on the CD, the previouschapter on the DVD, or to go down in cursor mode. • REV — Press to reverse within the acti...

6. AUX control Press to switch DVD player from play mode to auxiliary mode. 7. Auxiliary jacks Input jacks for standard video/audio media device. 8. STOP/EJECT control Press once to stop a disc from playing. Press a second time to eject thedisc. (If a disc is not playing, but is present in the syste...

Remote control 1. REV (REVERSE) control Press to reverse the direction of the DVD movie. 2. FWD (FORWARD) control Press to advance the direction of the DVD movie. 3. PLAY/STOP control When playing, press PLAY/STOP to stop the disc. When stopped, pressPLAY/STOP to play the disc. 4. SEEK control Press...

• Always save MP3 files with the .mp3 extension. The player recognizesan MP3 file by the .mp3 extension, so MP3 files saved with differentextensions will not be played. Never save a non-MP3 file with the.mp3 extension as the file will not play properly. • The player supports multi session discs. How...

On-screen indicators Each time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible indicators: 1. DVD/ CD STATUS (PLAY/FWD/REV/PAUSE) 2. CD track number / DVD title 3. DVD chapter number 4. MEDIA COUNTER — displays current viewing tim...

The front glass on the flip-down liquid crystal display (LCD) maybreak when hit with a hard surface. If the glass breaks, do not touch the liquid crystalline material. In case of contact with skin, washimmediately with soap and water. Do not expose the flip-down liquid crystal display (LCD) to direc...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/decrease the airflow...

Dual Zone Automatic Temperature Control with heated seats(if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/de...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theairflow selector in the OFF or with recirculated air engaged. • Do not put objects under the front seats ...

REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel andworks to clear the rear window of fog and thin ice. The ignition must be in the 3 (RUN) position to operate the rear windowdefroster. The rear defroster turns off automatically after 10 minutes or when thei...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamp switch to . The headlamps will turn off. Foglamp control (if equipped) With the ignition on, the foglampscan be turned on when theheadlamp control is pulled towardyou and is in any of the foll...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF, autolamps or parking lampposition and • the transmission must be out of the Park position. Always remember to turn on ...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down and hold the steeringwheel release control. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Pull the steering wheel releasecontrol up. This will lock thesteering wheel in position. Never adjust the steering wh...

INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may beused to secure sunglasses or similarsized objects. Press the control toopen the storage compartment. OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment Pr...

CENTER CONSOLE Your vehicle may be equipped with avariety of console features. Theseinclude: • Utility compartment with powerpoint • Gear Shift • Cup holders • Rear vent (if equipped) Use only soft cups in the cupholder. Hard objects can injure youin a collision. AUXILIARY POWER POINT (12VDC) Power ...

Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromits heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by yourwarranty. POWER WINDOWS Do not leave child...

To operate ONE TOUCH UP: • Pull the switch completely up tothe second detent and releasequickly. The window will closefully. Momentarily press theswitch to any position to stop thewindow operation. If the switch is pressed and held tothe normal open or ONE TOUCH DOWN position during a ONE TOUCHUP ev...

Accessory delay With accessory delay, the radio, Family Entertainment DVD System (ifequipped), power windows, and moonroof (if equipped) operate for upto ten minutes after the ignition switch is turned from the ON to theOFF position or until one of the front doors are opened. AUTOMATIC DIMMING INTER...

Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a ...

Memory feature (if equipped) The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features when a memory position is selected through theremote entry transmitter, keyless entry keypad or memory switch on thedriver’s...

STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features Press MEDIA to select: • AM, FM1, FM2 • SAT1, SAT2 or SAT3 (SatelliteRadio mode if equipped). • CD In AM, FM1, or FM2 mode: • Press SEEK to access thenext/previous strong station. In Satellite radio mode(if equipped): • Press SEEK to advan...

MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up toventilate the vehicle. Do not let children play with the moon roof or leave childrenunattended in the vehicle. They may seriously hurt themselves. To open the moon roof: The moon roof is equipped with ana...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a convenient way toreplace up to three hand-heldtransmitters with a single built-indevice. This feature will learn theradio frequency codes of mosttransmitters to operate g...

Note: There are 30 seconds in which to initiate Step 7. 7. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped de...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status. Thesystem will a...

RIGHT REAR DOOR AJAR. Displayed when the right rear door is not completely closed. PARK BRAKE ENGAGED. Displayed when the park brake is engaged. If the warning stays on after the park brake is off, contact yourauthorized dealer as soon as possible. LOW FUEL LEVEL. Displayed as an early reminder of a...

To reset the oil monitoring system to 100% after each oil change[approximately 5,000 miles (8,000 km) or 180 days] perform thefollowing: To reset the oil life to 100% with system warnings CHANGE OILSOON/OIL CHANGE REQUIRED displayed: 1. Select this function from theSETUP control for current displaym...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

• you put the vehicle in motion by releasing the brake pedal and thevehicle attains a speed greater than 5 mph (8 km/h). Deactivating/activating autolock Your vehicle comes with the autolock feature activated. There are threemethods to enable/disable this feature: One is through your authorizeddeale...

Power door lock/unlock inhibit feature As a theft deterrent, the power door lock controls can be disabled20 seconds after the ignition has been turned to the 1 (LOCK) positionand the vehicle is locked using the remote entry transmitter or thekeyless entry keypad. The door lock controls are re-enable...

Press to automatically move the seat, mirrors and adjustable pedals to the desired memory position (the positions correspond to the transmitterbeing used). Note: You can associate a specific remote entry transmitter to each memory position. For more information on programming thetransmitters to Driv...

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correc...

Note: Ensure the brake pedal is not depressed during this sequence. To reprogram the remote entrytransmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK)position and 3 (RUN). Note: The eighth...

The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Perimeter lamps illuminated entry With the remote entry system, the following items will illuminate whenthe (unlock) control on the transmitter is pressed: • Head lamps • Park lamps • T...

6. Press the power door unlock control twice within 5 seconds. Note: The horn will chirp once to indicate the perimeter lighting feature hasbeen deactivated. The horn will chirp once and honk once (one shortand one long) to indicate the perimeter lighting feature has beenactivated. 7. Turn the ignit...

KEYLESS ENTRY SYSTEM You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • open the trunk. • recall memory seat/powermirrors/adjustable pedalspositions 1 or 2. The keypad can be operated withthe factory set 5–digit entry code;this code is located on the owner’swall...

SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock 娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start...

The theft indicator will flash everytwo seconds to act as a theftdeterrent when the vehicle isarmed. Automatic disarming The vehicle is disarmed immediately after the ignition is turned from the1 (LOCK) to the 3 (RUN) position. The theft indicator will illuminate for three seconds and then go out. I...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle fromunauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL remote entry transmitters are brought to the authorized dealer to aid in troubleshooting. Ar...

• Press the 7 • 8 and 9 • 0 controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdownwhen any of the above actions occurbefore the vehicle becomes armed. Each door, the hood or the trunk isarmed individually, and if any areopen, ...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints Head ...

Using the manual lumbar support (if equipped) The lumbar support control islocated on the outboard side of theseatback. Move the control up or down toadjust lumbar support. Folding down the front passenger seatback The front passenger seatback can befolded to a horizontal position tomake room for a ...

Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Before ret...

Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automaticpositioning of the driver seat, powermirrors, and adjustable pedals totwo programmable positions. The memory seat control is locatedon the driver door. • To program position 1, move thedriver seat, mirrors and ped...

The head restraints can be movedup by pulling up on the headrestraint. Push release button to lower headrestraint. Split-folding rear seat One or both rear seatbacks can be folded down to provide additionalcargo space. To lower the seatback(s) frominside the vehicle, pull the straplocated on the out...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System 娂 to tailor the deployment level of the driver dual-stage airbag based on seatposition. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower air...

Safety belt precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passe...

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movem...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recom...

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt andincrease the risk of injury in a collision. Safety belt pretensioner Your vehicle is equipped with safety ...

hardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collision be replaced. However, if the collision was minor and anauthorized dealer finds that the belts do not show damage and continueto operate properly, th...

If... Then... The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km/h) and more than1-2 minutes have elapsed sincethe ignition switch has beenturned to ON... The Belt-Minder 威 feature is activated - the safety belt w...

Reasons given... Consider... “Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many when no other vehicles are around. “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’t...

Read Steps 1 - 4 thoroughly before proceeding with thedeactivation/activation programming procedure. Note : The driver and front passenger Belt-Minder 威 features must be disabled/enabled separately. Both cannot be disable/enabled during thesame key cycle. The driver and front passenger Belt-Minder 威...

• This will enable the Belt-Minder 威 feature for that seating position if it is currently disabled. As confirmation, the safety belt warning light willflash 4 times per second for 3 seconds, followed by 3 seconds with thelight off, then followed by the safety belt warning light flashing 4 timesper s...

Important supplemental restraint system precautions Airbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest close tothe trim covering the airbag module. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even wh...

Do not attempt to service, repair, or modify the airbagsupplemental restraint system (SRS) or its fuses. See your authorized dealer. Modifying or adding equipment to the front end of the vehicle(including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbaginflation. The fact that the airbagsdid not inflate in a collision does n...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS ...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a back-up tone to indicate the condition of t...

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided. How does the side airbag system work? The design ...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, i...

Do not lean your head on the door. The Safety Canopy 娂 could injure you as it deploys from the headliner. Do not attempt to service, repair, or modify the Safety Canopy 娂 system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy 娂 . See your authorized d...

If the Safety Canopy 娂 system has deployed, the Safety Canopy 娂 will not function again unless replaced.The Safety Canopy 娂 system (including the A, B, and Cpillar trim) must be inspectedand serviced by an authorizeddealer. If the Safety Canopy 娂 is not replaced, the unrepaired areawill increase the...

Important child restraint precautions You are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally children who are four years oldor younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, youmust put them in safety seats made especial...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Ford Motor Company recommends the use of a child safety seat having atop tether strap. Install the child safety seat in a seating position withLATCH and tether anchors. For more information on top tether strapsand anchors, refer to Attaching safety seats with tether straps in this chapter. For more ...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol. All the LATCH lower anchors areequally spaced, so that a singleLATCH child seat can be installed atany rear seating position. If two child safety seats are installedusing the LATCH l...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystander. Highway hazards No matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly to theclosest safe area out of traffic. This m...

3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’...

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load can be carried by the tire. This pressure isnormally higher than the manufacturer’s recommended cold inflationpressure which can be found on the Saf...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. If you need to use chains, it i...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cross thechains under the trailer tongue and allow slack for turning corners.If you use a rental trailer, follow the instructions that the rental agenc...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • If you ...

STARTING Positions of the ignition 1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and all electricalaccessories off without locking thesteering wheel. To lock the steeringwheel, remove the key then turn thesteering wheel. 2. ACC, allow...

• Make sure the gearshift lever is inP (Park). 3. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn t...

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If ...

Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control during emergency stops bykeeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking ...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

TRACTION CONTROL 姟 (IF EQUIPPED) Your vehicle may be equipped with a Traction Control 娂 system. This system helps you maintain the stability and steerability of your vehicle. Itis especially useful on slippery road surfaces. The system operates bydetecting and controlling wheel spin. The system borr...

To help avoid personal injury, always use caution when inR (Reverse) and when using the RSS. This system is not designed to prevent contact with small ormoving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damagingthe vehicle...

The RSS automatically turns onwhen the gear selector is placed inR (Reverse) and the ignition is ON.An RSS control on the instrumentpanel allows the driver to turn theRSS on and off. To turn the RSS offin any gear, the ignition must be ON. An indicator light on the controlwill illuminate when the sy...

If your vehicle is equipped with a 6–speed transmission: When driving at slow speeds in deep sand under high outside temperatures,use L (Low) gear when possible. L (Low) gear operation will maximizethe engine and transmission cooling capability. Do not perform this operation if your vehicle is equip...

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness areas. Ford MotorCompany joins the U.S. Forest Service and the Bureau of LandManagement in encouraging you to help preserve our national forest andother ...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in...

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. The fuel pump shut-off switch islocated in the front passeng...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — — — 30A Green Green Green Pin...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F16 10A Rear defroster indicator, Heatedmirrors F17 30A Rear defroster F18 10A PCM relay coil, Shifter Brake-ShiftInterlock (BSI), PassiveAnti-Theft System (PATS)module, Fuel relay coil, Brakelamps, Center High-Mounted ...

To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter. The high-current ...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For v...

Removing the spare tire and jack 1. Lift the trunk cargo cover, andremove the wing nut that securesthe spare tire by turning itcounterclockwise. 2. Lift and remove the spare tirefrom the trunk. 3. Remove the second wing nut thatsecures the jack retention bracketby turning it counterclockwise,remove ...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Take care toposition the jack as shown to ensurethat the locating holes in the jackbase can be placed on the locatingtabs of the jack mounting brack...

If you are stowing the temporaryspare tire, place the tire over the jack and secure it with the largewing nut. WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 100 miles (160 km)after any wheel disturbance (tire rotation, changing a flat tire, wheelremoval, etc.)...

Do not attempt to push-start your automatic transmissionvehicle. Automatic transmissions do not have push-startcapability. Attempting to push-start a vehicle with an automatictransmission may cause transmission damage. Preparing your vehicle When the battery is disconnected or a new battery is insta...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoid possible damage to the interior paintedsurfaces. • Do not use household or glass cleaners as these may damage thefinish of the instrument panel, ...

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaningthe seat-mounted side airbag (if equipped). Such products could contaminate the side airbag system and affect perform...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

Working with the engine on 1. Set the parking brake and ensure the gearshift is securely latched in P(Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removed an...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from the vehicle slightly. 2. Press the release button and pull the wiper blade from the wiper arm. 3. Attach the new wiper to the wiper arm by sliding it onto the wiperarm until it clicks into place. Replace wiper blades at least once per year fo...

5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the indicator back in an...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (an opaque plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine c...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” thatare sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes kno...

If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine. On restarting, cranking time will take a few seconds longerthan normal. • Normally, adding 1 gallon (3.8L) of fuel is en...

• Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump a...

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, s...

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not ready for I/M testing, the following driving cycle consistingof mixed city and highway driving may be performed: 15 minutes of steady driving on an ex...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...

If your transaxle does not engage normally, do not attempt todrive. The vehicle should be towed to your authorized dealer forevaluation. Checking 6–speed automatic transmission fluid (if equipped) Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Y...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Mobile-Ease 娂 hands free communication system Remote start Vehicle security systems Wheel locks Not all accessories are available for all models. For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding a...

A Accessory delay ..........................70 Air cleaner filter .......................271 Air conditioning ....................48, 50 Airbag supplemental restraintsystem ................131–132, 140, 142 and child safety seats ............133description ..............132, 140, 142disposal ..........