Ford 2007 F-550 v.1- User Manual

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Service Data Recording Service data recorders in your v...

Vehicle Modification Data Recording Some aftermarket products may cause severe engine and/or transmissiondamage; refer to the What is not covered section in The new vehicle limited warranty for your vehicle chapter of your vehicle’s Warranty Guide for more information. Some vehicles are equipped wit...

If your vehicle is equipped with theFord Ambulance PreparationPackage, it will be indicated on theSafety Compliance CertificationLabel. The label is located on thedriver’s side door pillar or on therear edge of the driver’s door. Youcan determine whether theambulance manufacturer followedFord’s reco...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag-Front Airbag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -Non-...

WARNING LIGHTS AND CHIMES Standard instrument cluster (manual transmission) Standard instrument cluster (automatic transmission) Harley-Davidson instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light...

Many lights will illuminate when you start your vehicle to make sure thebulbs work. If any light remains on after starting the vehicle, have therespective system inspected immediately. If your vehicle is equipped with a diesel engine, it has a unique cluster,refer to Starting the engine in your 6.0 ...

after releasing the parking brake indicates low brake fluid level and thebrake system should be inspected immediately by your servicingauthorized dealer. Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance may occur. It will take you lo...

Four wheel drive low: Illuminates when four-wheel drive low isengaged. Four wheel drive indicator: Illuminates when four-wheel drive isengaged. Speed control: Illuminates when the speed control is activated. Turnsoff when the speed control systemis deactivated. Turn signal: Illuminates when the left...

GAUGES Speedometer: Indicates the current vehicle speed. Standard instrument cluster Harley-Davidson instrumentclusters Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the ...

Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scalemay damage the engine. Standard instrument cluster Harley-Davidson instrumentcluster Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should s...

Battery voltage gauge (manualtransmission only): Indicates the battery voltage when the ignition is inthe ON position. If the pointer movesand stays outside the normal operatingrange, have the vehicle’s electricalsystem checked as soon as possible. Transmission fluid temperature gauge (automatic tra...

AUDIO SYSTEMS AM/FM stereo system (if equipped) The AM/FM stereo system does not contain rear speakers; only frontdriver side and passenger side speakers. Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, the window switchesand radio may be used for up to tenminutes a...

FADE (Fade): Press MENU to reach the fade setting. Use / / SEEK, SEEK to adjust the audio between the front and rear speakers. SPEEDVOL (Speed sensitive volume) (if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically changesslightly with vehicle speed to compensate for ro...

• Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thunderstorms can interfere with your reception. • Station overload: When you pass a broadcast tower, a stronger signalmay overtake a weaker one and play while the weak station frequencyis displayed. CD/CD p...

Satellite radio reception factors: To receive the satellite signal, your vehicle has been equipped with a satellite radio antenna located on theroof of your vehicle. The vehicle roof provides the best location for anunobstructed, open view of the sky, a requirement of a satellite radiosystem. Like A...

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brie...

: Distributes outside air through the instrument panel vents and center console vents (if equipped). : Distributes outside air through the instrument panel vents, floor vents and center console vents (if equipped). O (OFF): Outside air is shut out and the climate system is turned off. : Distributes ...

Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop. AUTOMATIC TEMPERATURE CONTROL SYSTEM (IF EQUIPPED) Press the AUTO and (floor/defrost) controls at the same time and hold for one second to switch between Fahrenheit and Celsius. ...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

Vertical and horizontal aim adjustment (sealed beam headlamps) The headlamps on your vehicle are intended to be aimed usingmechanical aimers. If mechanical aimers are used and the cross-car sightline is in any way blocked, set the legs of the universal adaptor all to thesame setting, such that the c...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

TRANSMISSION CONTROL Tow/Haul feature (5–speed automatic transmission) (if equipped) To activate, press the transmissioncontrol switch (TCS) located on thegearshift. The TOW/HAUL indicatorlight will illuminate in theinstrument cluster. The transmissionwill operate in all gears. Press thetransmission...

POWER WINDOWS (IF EQUIPPED) Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the pro...

Power rear slider window (if equipped) Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not...

Heated outside mirrors (if equipped) The main mirror glass is heated automatically to remove ice, mist andfog and activates when the vehicle is started. Note: The mirrors may be hot to the touch but will not burn. This is a normal condition. Type A The mirror heating elements aredesigned to operate ...

The relays and fuse in the glove box are coded as shown in theaccompanying illustration. There will also be one power leadfor each switch found as a blunt-cutand sealed wire located behind thepassenger compartment fuse panel. They are coded as follows: Switch Circuit number Wire color Fuse AUX 1 193...

STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate controlfeatures. Radio control features • Press MODE to select AM, FM1,FM2, TAPE or CD (if equipped). In Radio mode: • Press NEXT to seek/scan to thenext strong station. In Tape mode: • Press NEXT to lis...

• The engine oil pressure is low. • The fuel gauge is at or near empty. Check trailer (if equipped): Displayed when a trailer connectionbecomes disconnected, eitherintentionally or unintentionally, andhas been sensed during a givenignition cycle. Refer to Integrated trailer brake controller in the T...

Selectable features Reset Press this control to select and resetfunctions shown in the INFO menuand SETUP menu. Info menu This control displays the followingcontrol displays: • Odometer/Compass • Trip odometer/Odometer/Compass • Distance toEmpty/Odometer/Compass • Average Fuel Economy/Odometer/Compa...

Compass zone/calibration adjustment 1. Determine your magnetic zone byreferring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine. 4. From Info menu, press and holdthe SETUP and RESET controlssimultaneously until the messagecenter display changes to show thecurrent zone setti...

2. Pressing the RESET controlcycles the message center througheach of the language choices. 3. Press and hold the RESETcontrol to set the language choice. System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple war...

Warning display Status Low fuel level Warning returns after 10 minutes Low brake fluid level Low oil pressure Check engine temperature Trailer disconnected Water in fuel (diesel only) Check air filter (diesel only) Door ajar Warning returns after the ignition keyis turned from OFF to ON. Check fuel ...

Tailgate removal Your tailgate is removable to allowmore room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry thespring clip (on each connector) pastthe head of the support screw.Disconnect cable. 3. Disconnect the other cable. 4. Lift tailgate to a 45–degree angle. 5. Lift right sid...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency. If you lose your authorized dealer supplied keys, replacement keys areavailable through your authorized dealer. POWER DOOR LOCKS (IF EQUIPPED) Press co...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...

To program the keyless entrykeypads remote entry transmittersyourself: 1. Ensure the vehicle iselectronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 2 (LOCK)position to 3 (OFF). 4. Cycle eight times rapidly (within10 seconds) between the 3 (OFF)position and 4 (ON). Note: ...

• The factory set code will work even if you have set your own personalcode. • If you set a second personal code it will erase your first personal code. Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold t...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints (if e...

Captain’s chair (if equipped) • Lift the bar to move the seatforward or rearward. Make surethat the seat is relatched intoplace. • To recline the seatback, pull therelease lever handle located onthe side of the seat up. • Push down the lever (ifequipped) located at the bottomof the seatback to quick...

Using the manual lumbar support For more lumbar support, turn thelumbar support control toward thefront of vehicle. For less lumbar support, turn thelumbar support control toward therear of vehicle. Heated seats (if equipped) To operate the heated seats, do the following: • Push control to activate....

1. Pull down the latch lever locatedon the bottom seat back to fold theseat back forward. 2. Pull up on the lever located onthe side of the seat cushion torotate the cushion up until it locksinto a vertical storage position,gaining access to the grocery hooklocated on the underside of thedriver-side...

To gain access to the cupholdersand tray, pull down on the armrest. To gain access to the 60/40 loadfloor, store the cushion in theupright locked position. Pull up onthe straps located at the sides of theload floor, and rotate forward untilresting on the carpet. SAFETY RESTRAINTS Safety restraints p...

It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people toride in any area of your vehicle that is not equipped with seats andsafety belts. Be sure everyone i...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The front outboard and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front outboard passenger andrear seat outboard safety belts have two types of locking modesdescribed below: Ve...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checkedaccording to the procedures in the Workshop Manual . Failure to replace the belt and retractor assembly could increase the...

• 4–door Super Cab To adjust the shoulder belt height, push the button and slide the heightadjuster up or down. Release the button and pull down on the heightadjuster to make sure it is locked in place. Position the safety belt height adjusters so that the belt restsacross the middle of your shoulde...

If... Then... The driver’s safety belt is buckledbefore the ignition switch is turnedto the ON position... The BeltMinder 威 feature will not activate. The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection when used withsafety belts. Frontal airbags are not designed toinflate in rear and side crashes or rollovers. “I’d rather bethrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety b...

Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front seat belt buckleassem...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your authorized dealer. The front passenger air bag is not designed to offer protection toan occupant in the center front seating position. Modifying or adding equipment to the front end of the ve...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainssufficient longitudinal deceleration.The fact that the airbags did notinflate in a collision does not meanthat something is wrong with thesystem. Rather, it means the forceswere not...

If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS consists of: • driver and passenger airbag modules (which include the inflators andairbags), ...

• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can constantly monitor the child’s condition. 3. Medical condition. A passenger has a medical condition which, according to his or her physician:...

• the child has a medical condition that, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can monitor the child’s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a sp...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. Children and safety belts If the child is the pro...

• Those with a high back. If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Either type can be used at any seating position equipped withlap/shoulder belts if your child is over 40 lb. (18 k...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

• F-Series Crew Cab Tether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position. 4. You may need to pull the seatback forward to access the tethera...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information on shiftingprocedures and maintenance can befound in your Owner’s Guide . You should become thoroughly familiarwith this information befor...

government test course. For example, a tire graded 150 would wear oneand one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actualconditions of their use, however, and may depart significantly from thenorm due to variat...

At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall tires to the inflation pressure recommended by Ford Motor Company. Use a tire gauge to check the tire inflation pressure, including the spare(if equi...

Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, theycannot be treated like normal light truck tires. Tire service, includingadjusting the air pressure, must be performed by personnel trained,supervised and...

Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear andremove objects such as stones, nails or glass that may be wedged in thetread grooves. Check for holes or cuts that may permit air leak...

Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Built-in treadwearindicators, or “wear bars”, whichlook like narrow strips of smoothrubber across the tread will appearon the tire when the tread is worn...

built. For example, the numbers 317 mean the 31st week of 1997. After2000 the numbers go to four digits. For example, 2501 means the 25thweek of 2001. The numbers in between are identification codes used fortraceability. This information is used to contact customers if a tire defectrequires a recall...

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. It is recommended that the two front tires or two rear tires generally bereplaced as a pair. Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe pos...

Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by your authorizeddealer. Front wheel drive (FWD) vehicles and those with an independentrear suspension (if equipped) may require alignment of all four wheels. The tires should also ...

different in brand, size or appearance from the road tires and wheels. Ifyou have a dissimilar spare tire/wheel it is intended for temporary useonly and should not be used in a tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requir...

identifies and describes the fundamental characteristics of the tire andalso provides a U.S. DOT Tire Identification Number for safety standardcertification and in case of a recall. Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions ...

on your vehicle may operate at different conditions for load and inflationpressure. These speed ratings may need to be adjusted for the differencein conditions. The ratings range from 81 mph (130 km/h) to 186 mph(299 km/h). These ratings are listed in the following chart. Note: You may not find this...

11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Tire Label or SafetyCompliance Certification Label, which is located on the B-Pillar or theedge of the driver’s door, for the correct tire pressure for your vehicle. 12. Treadwear, Trac...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label (vehicles exported outside the U.S. and Canada maynot have a Tire Label) on the B-Pillar or the edge of the driver’s door.Look for “THE COMBINED W...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Tongue Load or Fifth Wheel King Pin Weight – refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5,000 lb. (2,268 kg) conventional trailer, multiply 5,000 by 0.10 and 0.15 to obtain a proper tongue load range of 500 to 750 lb.(227 to 340 kg). For an 11,5...

Loaded vehicles may handle differently than unloaded vehicles.Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Your vehicle can haul more cargo and people than most passenger cars.Depending upon the type and placement of...

Note: Do not exceed the GCWR listed for your vehicle on the following chart/table, or the GVWR, GAWR or tire ratings specified on the TireLabel or Safety Compliance Certification Label. Towing trailers beyond the maximum recommended trailerweight which exceeds the limit of the vehicle’s GCWR, GVWR, ...

Integrated hitch rating The standard integrated hitch has two ratings depending on mode ofoperation: • Weight carrying - requires a draw bar and hitch ball. The draw bar supports all the vertical tongue load of the trailer. • Weight distributing - requires an aftermarket weight distributing system w...

1. Park the unloaded vehicle on a level surface. With the ignition on andall doors closed, allow the vehicle to stand for several minutes so that itcan level. 2. Measure the height of a reference point on the front and rear bumpersat the center of the vehicle. 3. Attach the trailer to the vehicle an...

Integrated trailer brake controller (if equipped) Your vehicle may be equipped with a fully integrated electronic TrailerBrake Controller (TBC). When used properly, the TBC helps ensuresmooth and effective trailer braking by powering the trailer’s electricbrakes with a proportional output based on t...

3. GAIN setting display: Shows the current GAIN setting. This will illuminate when a trailer is connected, flash if the trailer becomesdisconnected, or remain off if no trailer is connected. 4. OUTPUT bar graph: When the vehicle’s brake pedal is pushed, or when the manual control is activated, green...

5. In a traffic-free environment, tow the trailer on a dry, level surface ata speed of 20 – 25 mph (30 – 40 km/h) and squeeze the manual controllever completely. 6. If the trailer wheels lock-up (indicated by squealing tires), reduce theGAIN setting; if the trailer wheels turn freely, increase the G...

Driving while you tow When towing a trailer: • Do not drive faster than 70 mph (112 km/h) during the first 500 miles(800 km) of trailer towing and don’t make full-throttle starts. • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep grades. • C...

Tires • All trailer tires should be of the same size, and construction. • Select tires that meet the trailer loading requirements. • Always check tow vehicle and trailer tire pressure before towing. Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not ...

4x4 with manual shift transfer case: • Place the transfer case in N (Neutral). • Front hub locks are in the FREE position. 4x4 electronic shift transfer case vehicles with automatictransmissions: Regarding recreational towing or having your vehicle towed, 4x4 vehicleswith electronic shift on the fly...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. Forvehicles equipped with a manualtransmission, you must depre...

Extended idling at high engine speeds can produce very hightemperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the engine compartment and exhaust system,...

If starting a vehicle with an automatic transmission: 1. Make sure the parking brake isset. 2. Make sure the gearshift is in P(Park). If starting a vehicle with a manualtransmission: 1. Make sure the parking brake isset. 2. Push the clutch pedal to the floor. 2007 F-250/350/450/550 (f23) Owners Guid...

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine 1. Turn the key to 4 (ON) withoutturning the key to 5 (START). 2. Turn the key t...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.5 cm) or adjust the heatingor air conditioning to bring in fresh air. USING THE ENGINE BLOCK HEATER (IF EQUIPPED) Use of an engine block heater isstr...

Parking brake To set the parking brake, press theparking brake pedal down until thepedal stops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated until theparking brake is released. Pull the right side of the releaselever to release the parking brake;the release leve...

Note: If your vehicle is equipped with a manual transmission, the engine may be required to run while power accessories operate and the parkingbrake is set. It is recommended that wheel chocks be used during thisoperation. If you’re parking your vehicle on a grade or with a trailer, press and holdth...

A high crown in the road or high crosswinds may also make the steeringseem to wander/pull. TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, theTraction-Lok axle functions like a ...

If you cannot move the gearshift lever out of P (Park) with ignition inthe 4 (ON) position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to 2 (LOCK), then removethe key. 2. Insert the key and turn it to 3 (OFF). Apply the brake pedal and shift to N (Neutral) . When the...

To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral position. 3. Start the engine, then press the brake pedal and release the parkingbrake. 4. Move the gearshift lever to the desired gear (1st or Revers...

Maximum downshift speeds 1 6-speed transmission Shift from: Transfer case position (if equipped) 2 2H or 4H 4L D (Overdrive) - 4 45 mph (72 km/h) 16 mph (26 km/h) 4-3 35 mph (56 km/h) 12 mph (19 km/h) 3-2 20 mph (32 km/h) 8 mph (13 km/h) 2-1 5 mph (8 km/h) 2 mph (3 km/h) 1-LO Only shift to LO when a...

Removing the key Turn the ignition off, push therelease lever (located above theignition), then turn the key towardyou and remove the key. REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Reverse) is s...

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this typeof vehicl...

LOW (4WD Low) can be engaged, the vehicle speed must bebelow 3 mph (5 km/h) with the brake pedal depressed and thetransmission in N (Neutral). This vehicle is equipped with anon-synchronous low range gearset which will not allow thetransfer case to shift into 4X4 LOW (4WD Low) if vehicle speedis abo...

• LOW RANGE – momentarily illuminates when the ignition isturned to the ON position.Illuminates when 4L (4x4 Low) isengaged. Using a Manual Shift On Stop (MSOS) 4WD system (if equipped) Note: Some noise may be heard as the 4WD system shifts or engages. This is normal. 2H (2WD High) – For general on-...

Shifting from 4H (4WD High) to 2H (2WD High) Move the transfer case lever to 2H(2WD High) at a stop or a vehiclespeed below 3 mph (5 km/h). With the vehicle at complete stop,disengage the locking hubs(optional) by rotating the hub lockcontrol from LOCK to FREE. • For proper operation, makesure that ...

Using the N (Neutral) position The transfer case neutral position overrides the transmission andputs the vehicle in neutral regardless of transmission gearshiftlever position. The vehicle can move forward or backwards. This position should only be usedwhen towing the vehicle. Do not leave the vehicl...

Shifting from 2WD (2WD High) to 4x4 HIGH (4WD High) Rotate the 4WD control to the 4x4HIGH position at speeds up to 55mph (88 km/h). • The electronic shift 4WDsystem is designed to engage4x4 HIGH (4WD High) whenthe vehicle is moving. Ifshifted to 4x4 HIGH (4WDHIGH) while at complete stop,4x4 may not ...

4. Move the 4WD control to the 4x4LOW position. 5. Hold the shift conditions until theLOW RANGE indicator lightilluminates. 6. If the LOW RANGE indicator light does not illuminate within 15 seconds, allow the vehicle to moveat a speed above 1 mph (1.6 km/h),then repeat steps 3 through 5before report...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Even 4WD vehicles can lose traction in slick mud. Aswhen you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until ...

When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This reduces strain on theengine and the possibility of stalling. If you do stall out, do not try toturn around because you might rollover. It is better to ...

Make sure you allow sufficient distance between you and other vehiclesfor stopping. Drive slower than usual and consider using one of the lowergears. In emergency stopping situations, avoid locking of the wheels. Usea “squeeze” technique, push on the brake pedal with a steadily increasingforce which...

auxiliary horsepower draw, vehicle conditions and surroundingenvironmental conditions and other factors, this can contribute toelevated transmission fluid temperatures and result in accelerated fluiddeterioration, fuel vapor over-pressurization, and other concerns. Fordtrucks are fully qualified for...

Installing the snowplow Weight limits and guidelines for selecting and installing the snowplow canbe found in the Ford Truck Body Builders Layout Book, Snowplow section, found at www.fleet.ford.com/truckbbas. A typical installationaffects the following: • Certification to government safety laws such...

The attached snowplow blade restricts airflow to the radiator, and maycause the engine to run at a higher temperature: • If you are driving more than 15 miles (24 km) where outside airtemperatures are above freezing, then angle the plow blade to full leftor right to maximize airflow to the radiator....

Transmission operation while plowing Operate the vehicle with the automatic transmission gearshift lever inthe D (Overdrive) position and Tow/Haul OFF. • Shift transfer case to 4x4 LOW (4WD Low) when plowing in smallareas at speeds below 5 mph (8 km/h). • Shift transfer case to 4x4 HIGH (4WD High) w...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the flasher...

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover. To reset the switch: 1. Turn the ignition off. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition on. 5. Wait a few seconds...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 304 — Not used 305 Full ISO relay Upfitter control 306 Full ISO relay Delayed accessory 307 Full ISO relay Starter 601 30A circuit breaker Delayed accessory, Powerwindows, Moonroof 602 — Not used * Mini fuse ** Cartridg...

• Wet weather driving capability Location of the spare tire and tools If your vehicle is equipped with a spare tire, jack and associated tools,refer to the following table for their locations: Tool Location Spare tire (pick-up trucks only) Under the vehicle, just forward ofthe rear bumper Jack Regul...

Tire change procedure 1. Park on a level surface, activatehazard flashers and set the parkingbrake. • Automatic transmission: Placegearshift lever in P (Park). • Manual transmission: Placegearshift lever in R (Reverse). • Electronic Shift-On-the-Fly(ESOF) 4WD: Place transfer casein any position. • M...

If the vehicle slips off the jack, you or someone else could beseriously injured. The following steps apply to F–250/F–350 Single Rear Wheel(SRW) vehicles only (unless otherwise noted): 6. Insert the hooked end of the jackhandle into the jack and use thehandle to slide the jack under thevehicle. 7. ...

• Front passenger side (4x4) Note: View shown from the rear of the vehicle to clearly identify thejack point. Place the jack directlyunder the axle. • Rear (including F-350 Dual Rearwheel [DRW] vehicles) Never use the front or reardifferential as a jacking point. To lessen the risk ofpersonal injury...

• Rear: F-450/F-550 14. Insert the jack handle into thepump linkage. 15. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground. Hydraulic jacks are equippedwith a pressure release valvethat prevents lifting loads whichexceed the jack’s rated capacity. 16. Remove t...

The following steps apply to all vehicles: 19. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nuttorque specification. 8–lug nut torque sequence 10–lug nut torque sequence 20. Stow the flat tire. ...

Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing in the directionspecified on the Tire Changing Instructions located with the jackhardware. 2. Slide the w...

may have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Over time, theadaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery ...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheelson the ground and the rear wheels ...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party mediation/arbitration program administered by the CanadianMotor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relat...

Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide Fre...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

racks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your authorized dealer has touch-up paint and sprays to match yourvehicle’s color. Take your color code (printed on a sticker in the driver’sdoor jamb) t...

• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. • Cover the highlighted areas to prevent water damage when cleaningthe engine. • 5.4L V8 gasoline engine • 6.8L V10 gasoline engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved produ...

• For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassCleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the w...

INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then dry by wipingwith a dry, soft, clean cloth. • Do not use household or glass cleaners as these may damage thefinish. INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner. • ...

LEATHER SEATS FOR THE KING RANCH F-250 AND F-350CREWCAB ONLY (IF EQUIPPED) Your vehicle is equipped with seating covered in premium, top-grainleather which is extremely durable, but still requires special care andmaintenance in order to ensure longevity and comfort. Regular cleaning and conditioning...

Conditioning Bottles of King Ranch Leather Conditioner are available at the KingRanch Saddle Shop. Visit the Web site at www.krsaddleshop.com , or telephone (in the United States) 1–800–282–KING (5464). If you areunable to obtain King Ranch Leather Conditioner, use another premiumleather conditioner...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your authorized dealer has many quality products available to clean yourvehicle and protect its finishes. These quality products have beenspecifically engineered to fulfill your automotive needs; they are customdesigned to complement the style and appearan...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your authorized dealer canprov...

2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, p...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Do not use any special washer fluidsuch as windshield waterrepellant-type fluid or bug wash asthis ...

4. Poor wiper quality can be improved by cleaning the wiper blades andthe windshield; refer to Windows and wiper blades in the Cleaning chapter. 5. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice h...

6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range. • Oil levels above the M...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

• All engines When the engine is cold, check the level of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to the scheduled maintenance information...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come outforcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance Product Specifications...

2. Arrange for the vehicle to be taken to a service facility. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Re-start the engine and take your vehicl...

The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO N...

If the “Check Fuel Cap” indicator comes on and stays on after you startthe engine, the fuel filler cap may not be properly installed. Turn off theengine, remove the fuel filler cap, align the cap properly and reinstall it. If you must replace the fuel filler cap, replace it with a fuel fillercap tha...

Running out of fuel Avoid running out of fuel because this situation may have an adverseaffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine....

For consistent results when filling the fuel tank: • Turn the engine/ignition off prior to refueling, an error in the readingwill result if the engine is left running. • Use the same filling rate setting (low-medium-high) each time thetank is filled. • Allow no more than 2 automatic click-offs when ...

POWER STEERING FLUID Check the power steering fluid.Refer to the scheduled maintenance information for the service interval schedules. If addingfluid is necessary, use onlyMERCON 威 ATF. Check the fluid level when it is at ambient temperature, 20°F–80°F(-7°C–25°C): 1. Check the fluid level on the dip...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...

1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir. 2. Remove cap and rubberdiaphragm from reservoir. 3. Add fluid until the level reachesthe step in the reservoir. 4. Reinstall rubber diaphragm andcap onto reservoir. TRANSMISSION FLUID Checking automatic t...

If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician. An overfill condition oftransmission fluid may cause shift and/or engagement concernsand/or possible damage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials m...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at thebottom of the opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. I...

CHECKING AND ADDING TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to Main...

Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element • 5.4L Engine 1. Release two retainer clamps. 2. Pull air filter tray assembly outtoward front of vehicle and lift airfilter element up and out of housing. Th...

1. World manufacturer identifier 2. Brake type and gross vehicleweight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a transmission/transaxle code on t...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada authorizeddealer. These quality accessories have been specifically engineered tofulfill your automotive needs; they are custom des...

A Accessory delay ..........................61 Air cleaner filter .......287–288, 290 Air conditioning ..........................39 Airbag supplemental restraintsystem ................................110–111 and child safety seats ............112description ..............................111disposal ...

fluid, checking and adding(manual) .................................286fluid, refill capacities ..............291manual operation ....................182 Turn signal ..................................48 U Upfitter controls .........................67 V Vehicle Identification Number(VIN) ...............