Ford 2007 Expedition v.3- User Manual

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Your vehicle is not equipped with a snowplowing package. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive yo...

Export unique (Non–United States/Canada) vehicle specificinformation For your particular global region, your vehicle may be equipped withfeatures and options that are different from the ones that are describedin this Owner’s Guide. A market unique supplement may be supplied that complements this boo...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Powertrain malfunction/reducedpower (RTT) (if equipped): Displays when the engine hasdefaulted to a ’li...

Low tire pressure warning (ifequipped): Illuminates when your tire pressure is low. If the lightremains ON at start up or whiledriving, the tire pressure should bechecked. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to ON, the light will ...

High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime (if equipped): Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and thedriver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps ar...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, theengine is overheating. Stop thevehicle as soon ...

Battery voltage gauge: Indicates the battery voltage when theignition is in the ON position. If thepointer moves and stays outside thenormal operating range, have thevehicle’s electrical system checkedby your authorized dealer as soon aspossible. Engine oil pressure gauge: Indicates engine oil press...

AUDIO SYSTEMS Quick start — How to get going Listening to the radio 1. If the audio system is off, pressVOL-PUSH to turn the radio on.Turn VOL-PUSH to adjust thevolume. Note: The system may take a few moments to turn on. 2. Press AM/FM repeatedly tochoose between AM/FM1/FM2frequency bands. 3. Press ...

For a single CD system, if a disc is not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the display. The firsttrack on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, pressLOAD. Select a slot numbe...

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random play. Otherwise,random play will begin when the current track is finished playing. CDSHUF will appear in the display.To disengage, press SHUFFLE again. ...

3. MENU: Press repeatedly to access the following settings: CATEGORY (satellite radio if equipped): When satellite radio mode is active, press MENU until the currently active category appears in thedisplay (CATEGORY MODE). In CATEGORY MODE, press / to scroll through the list of available SIRIUS chan...

SPEEDVOL (Speed sensitive volume): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louder withincreasing vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to adjust. The default setting is off; increasing your vehicle speed will not change the volume l...

5. SEEK : In radio mode, press / to access the previous/next strong station. In CD/MP3 mode, press / to access the previous/next CD/MP3 track. In satellite radio mode (if equipped), press SEEK, SEEK to seek to the previous/next channel. In CATEGORY MODE, press SEEK, SEEK to select a category (Jazz, ...

To view the station name or type: With RBDS ON, press TEXT/SCAN to toggle between displaying the station type (COUNTRY, ROCK, etc.) orthe station name (WYCD, WXYZ, etc.). BASS: Press MENU to reach the bass setting. Use / / SEEK, SEEK to adjust. TREB (Treble): Press MENU to reach the treble setting. ...

COMPRESS (Compression): Available only in CD/MP3 mode. Press MENU until COMPRESS ON/OFF appears in the display. Use / / SEEK, SEEK to toggle ON/OFF. When COMPRESS is ON, the system will bring soft and loud CD passages together for amore consistent listening level. Single Play/Dual Play: If Single Pl...

6. (Play/Pause): This control is operational in CD andDVD mode (if equipped). When aCD or DVD is playing in the FES system, press this control to play orpause the current CD/DVD. The CD/DVD status will display in the radiodisplay. If your vehicle is equipped with a Family Entertainment System (FES),...

17. LOAD: To load a disc into the system, press LOAD. Select a slotnumber using memory presets 1–6.When the display reads LOAD CD#,load the desired disc, label side up.If you do not choose a slot within 5 seconds, the system will choose foryou. Once loaded, the first track will begin to play. To aut...

Auxiliary input jack (Line in) Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers withhigh fid...

• Use the other controls to make adjustments to the playing media. • Dual Play mode may also beactivated by pressing memorypresets 2 and 4 simultaneously onthe front audio controls. The rear speakers mute and rear seat passengers have audio (for theirselected media) available through their headphone...

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors:...

CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re-recordable compactdiscs may not function correctly when used in Ford CD players. Do not use any irregular shapedCDs or discs with a scratchprotection...

• Creating discs with only one level of folders will help with navigationthrough the disc files. Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other t...

• Antenna obstructions: For optimal reception performance, keep theantenna clear of snow and ice build-up and keep luggage and othermaterial as far away from the antenna as possible. • Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage...

Quick start Your Family Entertainment System includes a DVD system, two sets ofwireless infrared (IR) headphones and a wireless infrared (IR) remotecontrol. To play a DVD in the DVD system: The DVD system can play DVD-Video, DVD-R, DVD-R/W discs as well asaudio CDs and video CDs. To ensure proper di...

DVD player controls 1. Headphone control A/B: Press to select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for that headset. When aheadphone channel has been selected (A or B), selections will affect thesource on that channel only. Note: Headphone A can acces...

Remote control Unless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the player.Ensure that there are no obstructions between the remote and player. 1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF. ...

22. ENTER: Press to select the highlighted menu option. 23. ILLUMINATION : Press to illuminate the remote control and backlight all of the buttons. Battery replacement Batteries are supplied with theremote control unit. Since allbatteries have a limited shelf life,replace them when the unit fails to...

Headphones Wireless headphones Your FES system is equipped with two sets of battery powered, infraredwireless headphones. Two AAA batteries are needed to operate theheadphones. (Batteries are included.) Additional infrared wireless headphones may be purchased for use withthe system. Also, wired head...

Channel A source. The wired headphone jack for Channel B is located onthe right side of the FES and is labeled B. Headphones plugged into this headphone jack will hear audio from the audio source selected to bethe Channel B source. Adjust the headphone volume usingthe volume control on the DVDsystem...

The three states are described as: FULL (enabled): The FES has control over the primary (speaker) and secondary (headphone) audio sources. LOCAL : The FES has control over the secondary source (headphones) only. The radio will ignore button presses that affect the primary(speaker) audio source. LOCK...

Do not leave children unattended in the vehicle and do not letchildren operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may becomeentangled in the cords and seriously injure themselves. The front glass on the liquid crystal display (LCD) flip-downscr...

pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance withthe instructions, may cause...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. MAX A/C: Distributes recircu...

with the front control. The rear cabin airflow temperature will match thedriver airflow temperature setting when only the center rear temperaturelight ( REAR ) is illuminated. The rear cabin airflow temperature will be warmer or cooler than the driver airflow temperature settingwhen more than one re...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument p...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument p...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to turn on the headlamps. Autolamp control The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp contro...

High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the foglamps on at full intensity output. To activate: • the ignitio...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operation. Move the control to the full uprightposition, past detent, to turn on theinterior lamps. Move the control to the full downposition, past detent, t...

4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge towards theright. If this edge is not at thehorizontal reference line, the beam will need to be adjusted so the edgeis at the same height as the horizontal reference line. 5. Locate the vertical adjuster oneach h...

INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • the remote entry controls arepressed and the ig...

Rear cargo lamp The dome lamp lights when: • any door is opened, and theswitch is in the middle position. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • any of the remote entry controlsare pressed and ignition is OFF(and switch is in the middleposition). With the i...

Function Number of bulbs Trade number Front park/turn lamps 2 3157 A Foglamps 2 9145 Front row map lamps 2 W5W Front row map/domelamps 3 578 Rear cargo lamp 1 578 2nd row reading lamp 2 W5W Turn/tail/brake/sidemarker lamps 2 3157K or 4157K Backup lamp 2 921 Approach/mirror turnsignal lamps (ifequipp...

Replacing front parking lamp/turn/sidemarker signal bulbs 1. Make sure that the headlamp control is in the OFF position.2. Open the hood. 3. At the back of the headlamp,remove the two headlamp assemblyretainer bolts. 4. Slide headlamp assembly forwardand off the retaining tab to exposethe back of th...

4. Rotate the bulb socket counterclockwise and remove from lampassembly. 5. Pull bulb straight out of socket and snap in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Carefully install the tail lamp assembly on the vehicle by securing thelamp assembly with ...

Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch isin the OFF position. 2. Remove the license lamp screwfrom the assembly. 3. Pull the lamp down and twist th...

Approach lamp bulb removal (if equipped) To change the bulbs: 1. Make sure that all the doors areclosed and the interior lights haveautomatically turned off or theopposite mirror approach lamp hasturned off. 2. With a small flat tippedscrewdriver, insert the tip into theapproach light module slot lo...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

For rear wash cycle, rotate (and hold as desired) the rear wiper/washercontrol to either position. From either position, the control will automatically return to the INT 2or OFF position. TILT STEERING WHEEL 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering up or do...

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Forward storage bin (if equipped) The storage compartment may beused to store a pair of sunglasses.Press the release area on the rearedge of the bin door to open thestorage compartment. The ...

Cupholder/Ashtray (if equipped) The cupholder/ashtray is located onthe instrument panel. To open cupholder/ashtray, push inon the door and release. The doorwill spring out 1/4+ inches. Thenpull cupholder/ashtray assembly outthe remaining distance to utilize. Toclose, push assembly in completelyand r...

Do not block the sensors on the front and back of the interiorrear view mirror since this may impair proper mirrorperformance. Do not clean the housing or glass of any mirror with harshabrasives, fuel or other petroleum-based cleaning products. EXTERIOR MIRRORS Power side view mirrors The ignition c...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control toadjust accelerator and brake pedal. • Press the top of the control toadjust the pedals ...

• Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate controlfeatures. Audio control features Press MEDIA to selec...

The moon roof has a built-in sliding shade that can be manually openedor closed when the glass panel is shut. To close the shade, pull it towardthe front of the vehicle. HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor,provides a ...

Note: There are 30 seconds in which to initiate Step 7. 7. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button. Repeat the press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped dev...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

STANDARD MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status preceded...

3. Locate the reset button on top ofthe compass sensor mounted behindthe mirror. 4. Press and hold the reset buttonon the compass module forapproximately 4 seconds until themessage center displays a selectionto change the current zone setting:ZONE <XX> RESET = CHANGE 5. Press and release the R...

5. The compass is now calibrated. Setup menu This menu allows the user, via the RESET stem located in theinstrument cluster, to interface and control the information displayed inthe message center for following selectable features: • System Check • Oil life • Units (English/Metric) • Autolamp • Auto...

OPTIONAL MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status preceded...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center will cyclethe display to show all warnings by displaying each one for 4 seconds. The message center will display the las...

Warning display Status For 4x4 low stop vehicle (ifequipped) Temporary alert For 4x4 apply brake (ifequipped) For 4x4 shift to N (ifequipped) To exit 4x4 low stop vehicle (ifequipped) To exit 4x4 apply brake (ifequipped) To exit 4x4 shift to N (ifequipped) DRIVER DOOR AJAR. Displayed when the driver...

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Do not install additional floor mats on top of the factory installedfloor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tolock in...

Keep keys out of reach of children. Do not allow children to playnear an open or moving power liftgate. Do not open the liftgate in a garage or other enclosed area with a lowceiling. If the liftgate is raised the liftgate could be damaged against alow ceiling. To open the liftgate from theInstrument...

To close the liftgate with therear cargo area control button: Press and release the control on theleft rear quarter panel to close theliftgate. The chime will beep once ifconditions are not correct to startan operation (i.e., the vehicle is outof park). In a normal close, thechime will begin just be...

MANUAL LIFTGATE (IF EQUIPPED) • To open the liftgate, position yourhand on top of the liftgate handleand pull to open the liftgate. • Do not open the liftgate orliftgate glass in a garage or otherenclosed area with a low ceiling.If the liftgate glass is raised andthe liftgate is also opened, bothlif...

Cargo shelf/divider (if equipped) The cargo shelf/divider is located behind the rear seat of your vehicle.The shelf has two positions: Flat shelf which pivots up and snaps intoplace OR a divider which pivots up and snaps vertically into place. Donot put more than 30 lbs. (14 kg) on the shelf. To mov...

LUGGAGE RACK Your vehicle is equipped with a roofrack for transporting items on theexterior of the vehicle. Themaximum recommended load to becarried on the roof rack is 200 lbs(90 kg), evenly distributed. Thecross-bars can be adjusted by usingthe thumbwheels at each end. Usethe tie-down loops on the...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (ON)position and the vehicle speed is 9 mph (15 km/h) or lower, and • the vehicle attains a speed greater than 12 mph (20 km/h). Deactivating/activating autolock Your vehicle comes with the autolock fe...

3. Enter 5–digit entry code 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has beendisabled or a chirp followed by a honk to indicate the system has beenenabled. Message cen...

The remote entry lock/unlock feature operates in any ignition position.The liftgate glass features operate as long as vehicle speed is less than5 mph (8 km/h). The panic feature operates with the key in the1 (OFF/LOCK) position. If there is any potential remote keyless entry problem with your vehicl...

• 4–button remote • 5–button remote If any of the doors or liftgate are ajar, the horn will make two quickchirps, reminding you to properly close all doors. Opening the liftgate window Press the control to unlatch the liftgate window. • 4–button remote 2007 Expedition (exd) Owners Guide (post-2002-f...

• 4–button remote • 5–button remote To deactivate the alarm, press the control again or turn the ignition tothe 2 (ACCESSORY) or 3 (ON) position. Memory feature The remote entry system can also control the memory feature. Press the control once to unlock the driver’s door. Pressing the controlwill a...

• 5–button remote Activating the memory feature To activate this feature: 1. Position the seat, rearview mirror, and adjustable pedals to thepositions you desire. 2. Press the SET control on the driver’s seat. 3. Within 5 five seconds, press one control on the remote transmitter andthen press the 1 ...

Programming remote transmitters It is necessary to have all (maximum of six — original and/or new) of your remote transmitters available prior to beginning this procedure. Ifall remote entry transmitters are not present during the programmingprocedure, the transmitters that are not present during pr...

Perimeter lamps illuminated entry The following items will illuminate when the (unlock) control on the remote entry transmitter is pressed: • Head lamps • Park lamps • Tail lamps The lamps will automatically turn off: • if the ignition switch is turned to the 3 (RUN) position, or • the (lock) contro...

• When the ignition is in the 3 (ON) position, the indicator will glow for3 seconds to indicate normal system functionality. If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. Ifthis occurs, the vehicle sho...

4. Turn the ignition from the 3 (ON) back to 1 (OFF/LOCK) position inorder to remove the second coded key from the ignition. 5. Within 10 seconds of removing the second coded key, insert the new unprogrammed key (new key/valet key) into the ignition and turn theignition from the 1 (OFF/LOCK) to the ...

SEATING Front row adjustable head restraints Your vehicle’s seats are equipped with two-way adjustable headrestraints. The purpose of these head restraints is to help limit headmotion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it is loca...

Lift handle to move seat forward orbackward. Manual seat recliner (if equipped) Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in t...

Using the armrest (if equipped) Push the release control to movethe armrest up or down. Using the manual lumbar support (if equipped) The lumbar support control islocated on the outboard side of theseat. Turn the lumbar support controlclockwise for more support. Turn the lumbar supportcounter-clockw...

Move the switch in the direction ofthe arrows to raise or lower the rearportion of the seat cushion. Press the switch in the direction ofthe arrows to move the seatforward, backward, up or down. Press the control to recline theseatback forward or rearward. Note: On vehicles with memory seats, to pre...

Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automaticpositioning of the driver seat, powermirrors, and adjustable pedals totwo programmable positions. The memory seat control is locatedon the outboard side of the seatcushion. • To program position 1, move thedriver ...

1. Lower the head restraints bypulling on the strap. 2. Locate handle on the side of theseat cushion by the door. 3. Pull up on the handle and pushthe seatback forward toward thefront of the vehicle. To return the seat to the upright position: 1. Lift the seatback toward the rearof the vehicle. 2. R...

2. Pull the handle up again until theseat releases from the floor. 3. Push the seat upward and fold itaway from the third row. Always latch the vehicle seat to the floor, whether the seat isoccupied or empty. If not latched, the seat may cause injury during a sudden stop. To return the seat to a sea...

Exiting the 3rd row 1. Pull the strap located at thebottom outboard of the seat back torelease the seat from the floor, androtate the seat up towards the frontseat. 2. Follow the directions above toreturn the seat from the E-Z entryand to the upright position. Reclining the 2nd row outboard 40% seat...

To prevent possible damage to the seat or safety belts, ensurethat the safety belts are not buckled when moving the seat to the load floor position. 2. With the latch released theseatback can be lowered into theload floor position. 3. To return the seat to the uprightposition, lift the seatback unti...

Adjusting the 2nd row center 20% seat (if equipped) Lift the handle to move the seatforward or backward. Note: This seat can be moved forward to keep a child in a childrestraint close to the front seat occupants. The seat should bemoved to the full rearward position when it is occupied by olderchild...

Pull up on the handle locatedbehind the seatback while pushingthe seatback forward and down intothe seat cushion. To return the seatback to its original position lift the seatback until itlatches into place. Before returning the seatback to its original position, make surethat cargo or any objects a...

SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and cra...

Determining if the Personal Safety System 姟 is operational The Personal Safety System 娂 uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Referto the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of th...

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest tothe direction the tongue is coming from) until you hear a snap and feel itlatch. Make sure the tongue is securely fastened in the buckle. • Front and rear seats 2. To unfasten, push the release ...

Front center lap belt To fasten the front center lap belt,insert the tongue into the centerbuckle until you hear a snap andfeel it latch. Make sure the tongue issecurely fastened in the buckle. Pullon the webbing to tighten the belt. All combination lap/shoulder belts, other than the driver’s belt, ...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if thesafety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly. In addition, all safetybelts should be checked for proper function. Failure to replace the beltand retractor assembly could incre...

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt andincrease the risk of injury in a collision. Second row comfort guide The second row outboardlap/shoulder b...

Position the safety belt comfort guide so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt andincrease the risk of injury in a collision. Safety belt extension assembly If the safety belt is too short ...

If... Then... The driver’s safety belt is notbuckled approximately5 seconds after the safety beltwarning light has turned off... The Belt-Minder 威 feature is activated - the safety belt warning lightilluminates and the warning chimesounds for 6 seconds every30 seconds, repeating forapproximately 5 m...

Do not sit on top of a buckled safety belt or insert a latchplateinto the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s air bag system One time disable Any time the safety belt is buckled and then unbuckled during anignition ON cycle, Belt-Mi...

4. Within approximately 7 seconds of the light turning off, buckle thenunbuckle the safety belt. • This will disable the Belt-Minder 威 feature for that seating position if it is currently enabled. As confirmation, the safety belt warning light willflash 4 times per second for 3 seconds. • This will ...

Additional equipment may affect the performance of the airbagsensors increasing the risk of injury. Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating positi...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

The RCM (restraints control module) monitors its own internal circuitsand the supplemental airbag electrical system wiring (including theimpact sensors, the system wiring, the airbag system readiness light, theairbag back up power and the airbag ignitors). Determining if the system is operational Th...

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided. How does the side airbag system work? The design ...

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of the type sufficient to cause activation. Side airbags are designedto inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-fro...

Do not attempt to service, repair, or modify the Safety Canopy 娂 system, its fuses, the A, B, C or D pillar trim, or the headliner on a vehicle containing a Safety Canopy 娂 . See your authorized dealer. All occupants of the vehicle including the driver should alwayswear their safety belts even when ...

If the Safety Canopy 娂 system has deployed, the Safety Canopy 娂 will not function again unless replaced.The Safety Canopy 娂 system (including the A, B, C, and Dpillar trim) must be inspectedand serviced by an authorizeddealer. If the Safety Canopy 娂 is not replaced, the unrepaired areawill increase ...

Important child restraint precautions You are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally children who are four years oldor younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, youmust put them in safety seats made especial...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

for children up to 60 pounds (27 kg) in a child restraint, and toprovide upper torso restraint for children up to 80 pounds (36 kg)using an upper torso harness and a belt-positioning booster. Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a ...

Installing child safety seats in the center front seating position(if equipped) Always transport children 12 years old and under in the rearseats and always properly use appropriate child restraints. It is safer to install child safety seats in seating positions thathave child seat anchors. The fron...

The tether strap anchors in your vehicle are in the following positions(shown from top view): • Second row bench seat • Second row bucket seats Attach the tether strap only to the appropriate tether anchor asshown. The tether strap may not work properly if attached somewhere other than the correct t...

6. Rotate the tether strap clip. 7. Tighten the child safety seat tether strap according to themanufacturer’s instructions. Third row seating position 1. Position the child safety seat on the center of the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. Information on transfer case operation and shifting procedurescan be found in the Driving chapter. Information on transfer case maintenance can be f...

At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall tires to the inflation pressure recommended by Ford Motor Company. Use a tire gauge to check the tire inflation pressure, including the spare(if equi...

To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile. If you are checking tire pressure when the tire is hot, (i.e. driven morethan 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires arehot from driving and it is norm...

cracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case it needs to be repaired or replaced. For your safety,tires that are damaged or show signs of excessive wear should not beused because they are...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If thebeads do not seat at the maximum pressure indicated, re-lubricate andtry again.When inflating the tire for m...

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystan...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Changing tires with TPMS Each road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby the tire and is not visibleunless the tire is removed. Thepressure sensor is locatedopposite (180 degrees) from thevalve stem. Care must be takenwhen...

no longer capable of functioning as intended. Please refer to thefollowing chart for information concerning your Tire Pressure MonitoringSystem: Low Tire PressureWarning Light Possible cause Customer Action Required Solid Warning Light Tire(s)under-inflated 1. Check your tire pressure toensure tires...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

any tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecommended inflation pressure. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires o...

your vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’sTire Label or Safety Compliance Certification Label: Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard e...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. D...

transport the cement to your home? If you and your friend each weigh220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) -(12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not haveenough cargo capacity to carry that much weight. In metric units, thecalculation would be: 635 kg - (2 x 99 k...

Engine Rear axle ratio Maximum GCWR - lb. (kg) Trailer weight range (0 - maximum) lb. (kg) Expedition EL (U.S. Only) Expedition Max (Canada Only) 4x2 5.4L with standard trailer tow package All 12200 (5534) 0–6000 (0–2721) 5.4L with optional trailer tow package All 15000 (6804) 0–9000 (0–4082) Expedi...

2. Turn the air suspension (if equipped) control to OFF. 3. Measure the height of a reference point on the front and rear bumpersat the center of the vehicle. 4. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within a 1 ⁄ 2 ” (13 mm) of the refere...

Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first500 miles (800 km) of towing a trailer, and don’t make full throttlestarts. • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep gra...

the lubricant specification. Remember that regardless of the rear axlelube used, do not tow a trailer for the first 500 miles (800 km) of anew vehicle, and that the first 500 miles (800 km) of towing be doneat no faster than 70 mph (112 km/h) with no full throttle starts. • After you have traveled 5...

If a distance of 50 miles (80 km) or a speed of 35 mph (56 km/h) mustbe exceeded, the drive shaft will have to be removed before the vehicleis towed. Ford recommends the driveshaft be removed/installed only by a qualifiedtechnician at an authorized dealer. See your authorized dealer fordriveshaft re...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. ON, all electrical circuitsoperational. Warning lightsil...

4. Make sure the parking brake isset. 5. Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you ...

3. After idling for a few seconds, apply the brake, shift into gear anddrive. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine stillfails to start, press the accelerator to the floor and try again; this willall...

results, plug the heater in at least three hours before starting the vehicle(the heater can be plugged in the night before starting the vehicle). Toplug the heater in, remove the cap from the plug and insert the plug intoa 110 volt grounded outlet. Be sure to re-attach the cap onto the plugwhen the ...

mechanical noise may be heard during this test. This is normal. If amalfunction is found, the ABS warning light will come on. If the vehiclehas continuous vibration or shudder in the steering wheel while braking,the vehicle should be inspected by an authorized dealer. The ABS operates by detecting t...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

• Driving on slick surfaces. • Cornering while towing a heavily loaded trailer (refer to Trailer towing in the Tires, Wheels and Loading chapter.) Roll Stability Control 娂 (RSC) The RSC system works in conjunction with the AdvanceTrac 威 system to help maintain roll stability of the vehicle during ag...

Aggressive driving in any road conditions can cause you to losecontrol of your vehicle increasing the risk of severe personal injury or property damage. The occurrence of a AdvanceTrac 威 with RSC event is an indication that at least some of the tires haveexceeded their ability to grip the road; this...

• High crosswinds • Wheels out of alignment • Loose or worn suspension components Variable assist steering Your vehicle is equipped with variable assist power steering. At lowengine RPM, steering assist will adjust to reduce efforts and improve lowspeed maneuverability. At high engine RPM, the assis...

LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, thelimited slip axle functions like a standard rear axle.Extended use of other than the manufacturer’s specified size tires on al...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your authorized dealer. Brake-shift interlock – floor-shift transmission This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever f...

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working proper...

Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normal detection zone of the reverse sensing system may create false beeps. The system will assist the driver in detecting certain objects while thevehicle moves in reverse at speeds less t...

Audible Warnings Distance to Object Warning Speed below 2.5 mph (4 km/h) up to 1.4 feet (.4 meters) Solid 1.4 feet (.4 meters) to 3 feet (.9 meters) Fast beep 3 feet (.9 meters) to 4.5 feet (1.4 meters) Medium beep 4.5 feet (1.4 meters) to 6.3 feet (1.9 meters) Medium/slow beep 6.3 feet (1.9 meters)...

damage drive components. 4H (4X4) and 4L (4X4 LOW) are onlyintended for consistently slippery or loose surfaces. Use of 4H (4X4) or4L (4X4 LOW) on these surfaces may produce some noise (such asoccasional clunks) but will not damage drive components. Your 4x4 features the heavy-duty Control Trac syst...

• 4L (4X4 LOW) provides electronically locked four-wheel drive when extra power at reduced speeds is required. The RTT location in themessage center will display “4X4 LOW” when this position is selected.This position is not recommended for use on dry pavement. Use thisposition for off-road low-speed...

Shifting to/from 4L 1. Bring the vehicle to a stop. 2. Place the gearshift in N (Neutral). 3. Move the control to the desired position. The message center will display “4X4 SHIFT IN PROGRESS” during theshift. The RTT location in the message center will then display thesystem mode selected. If any of...

steering and braking control of your vehicle, you must have all fourwheels on the ground and they must be rolling, not sliding or spinning. Basic operating principles • Do not use 4H (4x4) or 4L (4x4 LOW) on dry, hard surfaced roads.This may damage the driveline and axles. • Drive slower in strong c...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. If the ignition system gets wet, thevehicle may stall. Once thro...

possibly rolling over. Whenever driving on a hill, determine beforehandthe route you will use. Do not drive over the crest of a hill withoutseeing what conditions are on the other side. Do not drive in reverseover a hill without the aid of an observer. When climbing a steep slope or hill,start in a ...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in...

FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pumpshut-off switch may have been activated. The fuel ...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located under the right-hand side of the instrumentpanel. To remove the trim panel for accessto the fuse box, pull the paneltoward you and swing it out awayfrom the side and remove it. Toreinstall it, line up the tabs with thegrooves on the panel, t...

Always disconnect the battery before servicing high currentfuses. To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery sectio...

The use of tire sealants may damage your tires. The use of tiresealants may also damage your Tire Pressure Monitoring System. Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it wi...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For v...

Stopping and securing the vehicle 1. Park on a level surface, activatethe hazard flashers and set theparking brake. 2. Place the gearshift in P (Park)and turn the engine OFF. Spare tire information Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare is in ...

Tire change procedure To help prevent the vehicle from moving when you change a tire,be sure the parking brake is set, then block the wheels (both front or both rear) on the opposite end of the vehicle from the wheelbeing changed. If on a grade, block both opposite wheels on thedownward side of the ...

Stowing the spare tire 1. Lay the tire on the ground, near the rear of the vehicle, with the valvestem side facing up. 2. Slide the wheel partially underthe vehicle and install the retainerthrough the wheel center. Ifequipped, you may have to removethe wheel center cap prior topushing the retainer t...

1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on b...

4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, behind thebattery. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-)term...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the jump starting stud. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + – + – 2007 Expedition (exd) Owners Guide (po...

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the engine computer can relearn its idle conditions. + – + – 2007 Expedition (exd) Owners Guid...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is availablefrom your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent quality product to help protect from environmentaleffects. WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist ...

• To remove tar and grease, use Motorcraft Bug and Tar Remover(ZC-42), available from your authorized dealer. ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engi...

• For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassCleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the ca...

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoid possible damage to the interior paintedsurfaces. • Do not use household or glass cleaners as these may damage thefinish of the instrument panel, ...

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaningthe seat-mounted side airbag (if equipped). Such products could contaminate the side airbag system and affect perform...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood until the liftcylinders hold it open. 2007 Expediti...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 3V–V8 engine 1. Windshield washer fluid reservoir 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Power distribution box 8. Engine oil filler cap 9. Battery 2...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES It is recommended that wiper blades are renewed before winter. To replace the wiper blades: 1. Fold back the wiper arm andposition the wiper blade at rightangles to the wiper arm. 2. To remove, press the retainingclip (A) to disengage the wiperblade, then pull the blade dow...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and e...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by anauthorized dealer. 7. Put the indicator back in an...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and f...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the bat...

Add the proper mixture of coolant and water to the cooling system byfollowing these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tur...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely col...

FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif...

• Automotive fuels can be harmful or fatal if swallowed. Fuel such asgasoline is highly toxic and if swallowed can cause death or permanentinjury. If fuel is swallowed, call a physician immediately, even if nosymptoms are immediately apparent. The toxic effects of fuel may notbe visible for hours. •...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

the fuel filler cap, align the cap properly and reinstall it. The lamp will not reset immediately. Upon restarting the vehicle, it may take a fewdriving cycles (mileage accumulation) to clear the symbol. Continued driving with this lamp illuminated may cause the lamp to activate. If you must replace...

Repairs to correct the effects of using a fuel for which your vehicle wasnot designed may not be covered by your warranty. Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regula...

Running out of fuel Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine....

For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling,an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than t...

If other than Ford, Motorcraft or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in ...

eight times, it means that the vehicle is not ready for I/M testing; ifthe indicator stays on solid, it means that the vehicle is ready for I/M testing. The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is n...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operating range the perfo...

Changing the air filter element 1. Locate the Mass Air Flow Sensorelectrical connector on the air outlettube. This connector will need to beunplugged. 2. Reposition the locking clip on theconnector (connector shown frombelow for clarity), squeeze theconnector and pull it off of the airoutlet tube. 3...

Replace the spark plugs with ones that meet Ford material anddesign specifications for your vehicle, such as Motorcraft orequivalent replacement parts. The customer warranty may bevoid for any damage to the engine if such spark plugs are notused. MOTORCRAFT PART NUMBERS 1 For spark plug replacement,...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Mobile-Ease 娂 hands-free communication system Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to y...

A ABS (see Brakes) .....................257 Accessory delay ........................102 AdvanceTrac ..............................260 Air cleanerfilter ................... 357–358, 360–361 Air suspension ...........................265 description ..............................265 Airbag supplemental...

change oil soon warning,message center .......................334checking and adding ..............334dipstick ....................................334filter,specifications ..........336, 360–361recommendations ...................336refill capacities ........................362specifications ...........

P Panic alarm feature, remoteentry system ..............................150 Parking brake ............................259 Parts(see Motorcraft parts) ......360–361 Pedals (see Poweradjustable foot pedals) .............105 Power adjustable foot pedals ...105 Power distribution box(see Fuses) ...........