Ford 2006 Ranger v.1- User Manual

BREAKING-IN YOUR VEHICLE Your vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,600 km) ofnew vehicle operation. Vary your speed frequently in order to give themoving parts a chance to break in. Drive your new vehicle at least 50...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance PreparationPackage. Cell phone use The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

It may take a long period of time for the system to detect animproperly installed or properly re-installed fuel filler capdepending on driving and fuel tank level conditions. Refer to Fuel filler cap in the Maintenance and Specifications chapter. Brake system warning light: To confirm the brake syst...

Safety belt: Reminds you to fasten your safety belt. A chime will alsosound to remind you to fasten yoursafety belt. Charging system: Illuminates when the battery is not charging properly. Engine oil pressure: Illuminates when the oil pressure falls below thenormal range, refer to Engine oil in the ...

Four wheel drive low (ifequipped): Illuminates when four-wheel drive low is engaged. Four wheel drive high (ifequipped): Illuminates when four-wheel drive high is engaged. Itmay also illuminate when the 4WD LOW is engaged, refer to the Driving chapter for more information. Anti-theft system: Flashes...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMS AM/FM stereo (if equipped) Display preference: You can select Clock mode, which displays the time, or Frequency mode, which displays the current radio frequency, toappear in the radio display. Press CLK repeatedly to toggle betweenClock and Frequency modes. If clock mode is selected an...

To set the display mode: Press repeatedly to toggle between Clock mode and frequency mode. 3. AUDIO: Press AUDIO repeatedly to toggle through the followingmodes and use / to make adjustments in those modes. Bass: Press AUDIO to decrease/increase the bass setting. Treble: Press AUDIO to decrease/incr...

your original manually set preset stations.When the six strongest stations are filled, the station stored in preset 1will begin playing. If there are less than six strong stations, the systemwill store the last one in the remaining presets. Bass: Press MENU to decrease/increase the bass setting. Tre...

Autoset: Press MENU to access the autoset setting. Allows you to setthe strongest local radio stationswithout losing your original manually set preset stations for AM/FM1/FM2 . Use MENU to set.When the six strongest stations are filled, the station stored in preset 1will begin playing. If there are ...

Premium/Audiophile In-dash CD6/MP3 disc Pioneer audio system(if equipped) 1. AM/FM: Press to select AM/FM1/FM2 frequency bands. 2. CD: Press to enter CD mode. If a CD is already in the system, the discwill start playing. 3. EJ (CD eject): Press to eject the CD. Press and hold to eject all CDs. 4. CL...

10. Compression (Audiophile audios only): In CD/MP3 modes, press to bring loud and softpassages together for a more consistent listening level. 11. REPEAT: Press to repeat the current CD/MP3 track. The selectionwill repeat continuously untildeactivated. Press REPEAT again to deactivate. 12. FF (Fast...

CD units are designed to play commercially pressed 4.75 in (12cm) audio compact discs only. Due to technical incompatibility,certain recordable and re-recordable compact discs may notfunction correctly when used in Ford CD players. Irregularshaped CDs, CDs with a scratch protection film attached, an...

14. MUTE: Press to mute the playing media. Press again to returnto the playing media. 15. REW (rewind): Press to manually reverse a CD track. 16. SEEK: In radio, CD and MP3 flat file mode, press / to access the previous/next strongstation or track. In MP3 directory mode, press to select the next/pre...

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from a station, the weakerthe signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thunderstorms ...

Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12cm) audio compact discs only. Due to technical incompatibility,certain recordable and re-recordable compact discs may n...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief d...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theair flow selector in the OFF position. • Under normal weather conditions, do not leave the air flow selec...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly to ac...

Daytime running lamps (DRL) (if equipped) The daytime running light system turns the headlamps on, with areduced light output. To activate: • the ignition must be in the ON position and • the headlamp system is in the OFF position or parking lamp position. Always remember to turn on your headlamps a...

5. Locate the vertical adjuster foreach headlamp. Adjust the aim byturning the adjuster control eitherclockwise (to adjust down) orcounterclockwise (to adjust up). 6. In addition to the horizontal linemarked in step 2, a pair of verticallines (5) must be marked at thecenter line of the headlamps on ...

INTERIOR LAMPS Courtesy/reading lamps (if equipped) The courtesy lamp lights when: • any door is opened. • the instrument panel dimmerswitch is held up until thecourtesy lamps come on. • the remote entry controls arepressed and the ignition is OFF. BULB REPLACEMENT Headlamp Condensation The headlamp...

Function Number of bulbs Trade number Rear stop/turn/taillamps 2 4157K or 3157K Rear turn (STX only) 2 3156 Rear license platelamps 2 194 Backup lamps 2 3155 or 3156 (STX) Dome lamp 1 912 Map/dome-SuperCab(if equipped) 2 904 Map/dome-RegularCab (if equipped) 1 904 All replacement bulbs are clear in ...

4. Remove the bulb retaining ring byrotating it counterclockwise andslide the ring off the plastic base. 5. Remove the old bulb by pulling itstraight out of the lamp. Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and do not touch th...

3. Remove screw(s) from lampassembly and disengage lampassembly (it has a snap fit). 4. Rotate bulb socketcounterclockwise and remove fromlamp assembly. 5. Carefully pull bulb straight out ofsocket and push in the new bulb. 6. Install the bulb socket in lampassembly by turning clockwise. Install the...

Replacing tail lamp/backup lamp bulbs 1. Make sure the headlamp switch isin the OFF position and the openthe tailgate to expose the lampassemblies. 2. Remove the four screws and thelamp assembly from vehicle. 3. Rotate bulb socketcounterclockwise turn and removefrom lamp assembly. 4. Carefully pull ...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers(from desired interval to low or highspeed position); rotate towards youto decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single s...

Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lightersocket. Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromits heating position when it is ready to...

EXTERIOR MIRRORS Power side view mirrors (if equipped) To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mirrors in place. Fold-away mirrors Pull the side...

CARGO AREA FEATURES Cargo area shade (if equipped) Your vehicle may be equipped with notches in the side trim panels thatare used for a cargo area shade. See your authorized dealer for moreinformation. BEDRAILS (IF EQUIPPED) • This bedrail is for appearance use only. To help prevent injury, do not u...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency. Your keys are coded to your vehicle; using a non-coded key will notpermit your vehicle to start. If you lose your dealer supplied keys,replacement keys...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...

To reprogram the remote entrytransmitters: 1. Ensure the vehicle iselectronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 2 (LOCK)position to 3 (OFF). 4. Cycle eight times rapidly (within10 seconds) between the 3 (OFF)position and 4 (ON). Note: The eighth turn must end in ...

SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock 娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead ...

Replacement keys If your keys are lost or stolen and you don’t have an extra coded key,you will need to have your vehicle towed to an authorized dealer. Thekey codes need to be erased from your vehicle and new coded keys willneed to be programmed. Replacing coded keys can be very costly. Store an ex...

4. Within ten seconds of removing the previously programmed coded key,insert the other previously programmed coded key into the ignition. 5. Turn the ignition from the 3 (OFF) position to the 4 (ON) position.Keep the ignition in the 4 (ON) position for at least one second but notmore than 10 seconds...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Pull lever located at the side of theseat cushion up to adjust seatback. 60/40 seat (if equipped) To gain access to the storagecompartment in your armrest (ifequipped), lift the latch to open lid. The 60/40 seat cupholder (ifequipped) is detachable forcleaning. • Firmly grasp the bottom of thecup ho...

Booster seats must be installed only in seating positionsequipped with a combination lap/shoulder belt. SAFETY RESTRAINTSSafety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit w...

Automatic locking mode The automatic locking mode is not available on the driver safety belt. In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. This m...

After any vehicle collision, the seat belt system at all outboardseating positions (except driver, which has no “automatic locking retractor” feature) must be checked by an authorized dealer to verifythat the “automatic locking retractor” feature for child seats is stillfunctioning properly. In addi...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

• Regular Cab and 4–door SuperCab • 2–door SuperCab To lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the shoulder belt, slide the heightadjuster up. Pull down on the height adjuster to make sure it is locked inplace. Position the safety bel...

Do not use extensions to change the fit of the shoulder beltacross the torso. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then.....

If... Then... The driver’s safety belt is notbuckled before the vehicle hasreached at least 3 mph (5km/h) and 1-2 minutes haveelapsed since the ignitionswitch has been turned toON... The BeltMinder 威 feature is activated - the safety belt warning lightilluminates and the warning chimesounds for 6 se...

Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Interior in the Cleaning chapter. AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) pre...

Children and airbags For additional important safety information, read all information onsafety restraints in this guide. Never place a rearward facing child safety restraint in front of anactivated airbag. Airbags have been known to kill or injure children in front facing child safety restraints. W...

Booster seats must be installed only in seating positionsequipped with a combination lap/shoulder belt. To reduce the risk of injury, make sure children sit where theycan be properly restrained. How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the ve...

While the system is designed to help reduce serious injuries, it may alsocause minor abrasions, swelling or temporary hearing loss. Becauseairbags must inflate rapidly and with considerable force, there is the riskof death or serious injuries such as fractures, facial and eye injuries orinternal inj...

A difficulty with the system is indicated by one or more of the following: • The readiness lights will eitherflash or stay lit. • The readiness lights will notilluminate immediately afterignition is turned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the...

NHTSA deactivation criteria (excluding Canada) 1. Infant. An infant (less than 1 year old) must ride in the front seat because: • the vehicle has no rear seat; • the vehicle has a rear seat too small to accommodate a rear-facinginfant seat; or • the infant has a medical condition which, according to...

Transport Canada deactivation criteria (Canada Only) 1. Infant: An infant (less than 1 year old) must ride in the front seat because: • the vehicle has no rear seat; • the rear seat in the vehicle cannot accommodate a rear-facing infantseat; or • the infant has a medical condition which, according t...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions You are required by l...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulderbelt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk ...

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the stomach, and lets you adjust the shoulder belt to cross thechest and rest snugly near the center of the shoulder. The drawingsbelow compare the ideal fit...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

3. Locate the correct anchor for the selected seating position. The tether anchor is located on therear lower portion of the passengerseat. 4. Clip the tether strap to theanchor. 2006 Ranger (ran) Owners Guide (post-2002-fmt)USA (fus) Seating and Safety Restraints 97

Center seating location When installing a child safety seat in the front center position, route thetether strap over the center arm rest and clip it to the center anchor. If the tether strap is clipped incorrectly, the child safety seatmay not be retained properly in the event of a collision. 5. Ins...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information ontransfer case operation and shiftingprocedures can be found in the Driving chapter. Information on transfer case maintenance can be foun...

Every day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires and adjust ifrequired. At least once a month and beforelong trips, inspect each tire andcheck the tire pressure with a tiregauge (including spare, if equipped).Inflate all t...

Age Tires degrade over time, even when they are not being used. It is recommended that tires generally be replaced after 6 years of normalservice. Heat caused by hot climates or frequent high loadingconditions can accelerate the aging process.You should replace the spare tire when you replace the ot...

It is recommended that the two front tires or two rear tires generally bereplaced as a pair. Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not...

Front wheel drive (FWD) vehicles and those with an independent rearsuspension (if equipped) may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recom...

Note: You may not find this information on all tires because it is not required by federal law. 7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss ofvehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The...

Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, oroptional equipment. Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipme...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. 2006 Ranger (ran) Owners Guide (post-2002-fmt)USA (fus) Tires, Wheels and Loading 119

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more deta...

Special loading instructions for owners of pickup trucks andutility-type vehicles For important information regarding safe operation of this typeof vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this Owner’s Guide . Loaded vehicles may handle differently than unlo...

Refer to the following chart for information regarding thefactory-equipped trailer tow connector: Trailer tow connector Color Function Comment 1. Dark Green Trailer right-handturn signal Circuit activated when brakepedal is depressed or whenignition is on and right-handturn signal is applied. 2. Yel...

• Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance information for more information. Tr...

Vehicles equipped with an automatic transmission 4x2 and 4x4 vehicles with an automatic transmission follow theseguidelines for recreational towing: • Release the parking brake. • Turn the key in the ignition to the OFF/UNLOCKED position. • Place the transmission in N (Neutral). • Do not exceed a di...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. Forvehicles equipped with a manualtransmission, you must depre...

Starting the engine 1. Turn the key to 4 (ON) withoutturning the key to 5 (START). Ifthere is difficulty in turning the key,rotate the steering wheel until thekey turns freely. 2. Turn the key to 5 (START), thenrelease the key as soon as theengine starts. Excessive crankingcould damage the starter. ...

To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater) adapters. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-outand should be i...

Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake systemserviced immediately.) Parking brake To set the parking brake (1), pressthe parking brake pedal down untilthe pedal stops. The BRAKE warning la...

• uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steeringseem to wander/pull. TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces...

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the ON position unless the brake pedal is depressed. If you cannot move the gearsh...

Driving with a 5–speed automatic transmission (if equipped) This vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive Shift Strategy offers the optimal transmission operation andshift quality. When the vehicle’s battery has been disconnected for anytype of service or repair, the...

D (Drive) with Overdrive The normal driving position for thebest fuel economy. Transmissionoperates in gears one through five. D (Drive) without Overdrive D (Drive) with Overdrive can bedeactivated by pressing thetransmission control switch on theend of the gearshift lever. • This position allows fo...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transmission has a starter interlock that prevents crankingthe engine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then pu...

3. Turn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Removing the key Turn the ignition off, push therelease lever (located above theignition), then turn the key towardyou and remove the key. If...

1. Bring the vehicle to a complete stop 2. Depress the brake 3. On vehicles equipped with an automatic transmission, place thetransmission in N (Neutral); on vehicles equipped with a manualtransmission, depress the clutch. 4. Move the 4WD control to the desired position. • If shifting into 4WD LOW (...

• Be extremely careful when driving on pavement made slippery byloose sand, water, gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ease the vehicle back onto thepavement only aft...

Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,turn the steering wheel only as rapidly and as far as required to avoidthe emergency. Excessive steering will result in less vehicle control,not more...

If the transmission, transfer case or front axle are submerged in water,their fluids should be checked and changed, if necessary. Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant shouldbe replaced. After driving through mud, ...

When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This reduces strain on theengine and the possibility of stalling. If you do stall out, do not try toturn around because you might rollover. It is better to ...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the flasher...

The fuel pump shut-off switch islocated under the right-hand side ofthe glove box, just above the carpet. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 31 20A Front park lamps, Rear parklamps, License plate lamps,Dimmer switch, Trailer tow parklamps 32 5A Brake switch (logic) 33 5A Instrument cluster battery feed(B+) 34 20A Power point 35 15A Power locks Power distribu...

Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the followinglocations: Tool Location Spare tire Under the vehicle, just forward ofthe rear bumper Jack, jack handle, wheel nut wrench Regular Cab: behind the passengerseat, underneath the jack and toolscove...

5. With the spare tire on the ground,remove the retainer from the sparetire. Tire change procedure To help prevent the vehicle from moving when you change a tire,be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of thevehicle)...

• Never use the differential as a jacking point. 7. Remove the wheel lug nuts with the lug wrench. 8. Replace the flat tire with the spare tire, making sure the valve stem isfacing outward. Reinstall the lug nuts until the wheel is snug against thehub. Do not fully tighten the lug nuts until the whe...

5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, per Scheduled Maintenance Guide), or at any time that the spare tire is disturbed through service of othercomponents. 6. Install the spare tire lock (if equipped) into the access hole above therear bump...

Do not attempt to push-start your vehicle. Automatictransmissions do not have push-start capability; doing so maydamage the catalytic converter. Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the tr...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

achieving satisfaction by following the three-step procedure outlined onthe front page of the Warranty Guide. However, if your warranty concernhas not been resolved using the three-step procedure, you may beeligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of t...

If you cannot find unleaded fuel or can only get fuel with an anti-knockindex lower than is recommended for your vehicle, contact a regionaloffice or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emi...

(Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer orby writing to Ford Motor Company of Canada, Limited, ServicePublications, P.O. Box 1580, Station B, Mississauga, Ontario ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washing orlaundry liquid. These products can dis...

PAINT CHIPS Your authorized dealer has touch-up paint and sprays to match yourvehicle’s color. Take your color code (printed on a sticker in the driver’sdoor jamb) to your authorized dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar...

• 4.0L SOHC V6 engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, u...

special solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and windshield from automated carwash facilities. Be sure to replace wiper blades when they appearworn or do not function properly. • Do not use abrasives, as they may cause scratches. • Do not use ...

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over theleather. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleaner (ZC-11–A). Dry the area with a soft cloth. • To help maintain its resiliency and color, use the Motorcraft DeluxeLe...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer ca...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleane...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid ...

WINDSHIELD WASHER FLUID • 2.3L engine • 3.0L and 4.0L engines Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Do not use any special washer fluidsuch as windshield water r...

If you operate your vehicle in temperatures below 40° F (4.5°C),use washer fluid with antifreeze protection. Failure to use washer fluid with antifreeze protection in cold weather could result inimpaired windshield vision and increase the risk of injury or accident. Note: Do not put washer fluid in ...

• 4.0L SOHC V6 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the two holes or between the MIN and MAX marks (depending on application), the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the lower hole or the ...

• 3.0L V6 engine • 4.0L SOHC V6 engine • Oil levels above the upper hole or MAX mark may cause enginedamage. Some oil must be removed from the engine by an authorizeddealer. 7. Put the indicator back in and ensure it is fully seated. 2006 Ranger (ran) Owners Guide (post-2002-fmt)USA (fus) Maintenanc...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to scheduled maintenance information for the servi...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

When the engine is cold, check the level of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to the scheduled maintenance information for service i...

CXC-209 (Canada), meeting Ford specification WSS-M97B44–Dwith the factory-filled coolant. Mixing Motorcraft Specialty Orange Engine Coolant or any orange-colored extended life product with yourfactory filled coolant can result in degraded corrosion protection. • A large amount of water without engin...

5. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the “COLD FILL RANGE” or the “FULL COLD” level onthe reservoir. If you removed the radiator cap in an overflow system, fillthe radiator until the coolant is visible and radiator is almost full. 6. Replace the ...

• NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your ve...

• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and wash skin thoroughly with soap and water. Repeated orprolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful i...

• Keep the fuel pump nozzle in contact with the fuel container whilefilling. • DO NOT use a device that would hold the fuel pump handle in the fillposition. Fuel Filler Cap Your vehicle is equipped with a 1/4 turn fuel filler cap, which requiresthe handle to be rotated 1/4 of a turn for removal or i...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” thatare sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes kno...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple cal...

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a...

The EPA window sticker should be your guide for the fuel economycomparisons with other vehicles. It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of MPG (L/100 km)expected on the vehicle under optimum conditions. Your fuel economymay va...

If the vehicle’s powertrain system or its battery has just been serviced,the on-board diagnostics system is reset to a “not ready for I/M test”condition. To ready the on-board diagnostics system for I/M testing, aminimum of 30 minutes of city and highway driving is necessary asdescribed below: • Fir...

• 4.0L V6 engine Check the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules. If adding fluid is necessary, useonly MERCON 威 ATF. 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indic...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “MAX” linethat do not trigger the brake systemwarning lamp are within the normaloperating range, there is no need toadd fluid. If the fluid levels are outside of...

High fluid level Fluid levels above the safe rangemay cause overheating, shift and/orengagement concerns and internaltransmission damage. If an overfillcondition occurs, excess fluid shouldbe removed by an authorized dealer. Checking and adding manual transmission fluid (if equipped) 1. Clean the fi...

TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to Lubricant specifications...

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element.When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter. Note: Do not start your engine with the ai...

REFILL CAPACITIES Fluid Ford PartName Application Capacity Engine oil(includes filterchange) 7 Motorcraft SAE5W- 20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 SuperPremium MotorOil (Canada) 2.3L engine 4.0 quarts(3.8L) 3.0L V6 engine 4.5 quarts(4.3L) Motorcraft SAE5W-30 PremiumSynthetic...

Fluid Ford PartName Application Capacity Transmissionfluid 1 MotorcraftMERCON 威 ATF 5-speed manual 2.8 quarts(2.65L) 3 MotorcraftMERCON 威 V ATF 4x2 vehicleswith automaticand 2.3L I4engine 9.9 quarts(9.4L) 2 4x2 vehicleswith automaticand 3.0L or 4.0Lengines 10.0 quarts(9.5L) 2 4x4 vehicleswith automa...

Fluid Ford PartName Application Capacity Fuel tank N/A Regular cab(Short wheelbase) 17 gallons(64.4L) Regular cab(Long wheelbase) 20.3 gallons(76.8L) SuperCab 19.5 gallons(73.8L) Transfer caseFluid MotorcraftMERCON 威 ATF 4x4 Vehicles 1.25 quarts(1.2L) Front axlelubricant Motorcraft SAE80W-90Premium ...

2 Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amountof transmission fluid and fluid level should be set by the indication onthe dipstick’s normal operating range. 3 Service refill capacity for the manual tr...

Item Ford partname orequivalent Ford partnumber Fordspecification Brake fluid andclutch fluid (ifequipped) Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid PM-1 ESA-M6C25-A Door weatherstrips Silicone SprayLubricant XL-6 ESR-M13P4-A Engine coolant MotorcraftPremium GoldEngine Coolant(yellow-c...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Air cleaner filter ...............235–236 Airbag supplemental restraintsystem ..........................................78 and child safety seats ..............80description ................................78disposal ......................................83driver airbag ..............................