Ford 2006 Mustang v.2- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Base instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights ...

Service Engine Soon: The Service Engine Soon indicator light illuminates when the ignition is firstturned to the ON position to checkthe bulb. Solid illumination after the engine is started indicates the OnBoard Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (O...

Anti-lock brake system (ifequipped): If the ABS light stays illuminated or continues to flash, amalfunction has been detected, havethe system serviced immediately byyour authorized dealer. Normal braking is still functional unless the brakewarning light also is illuminated. Airbag readiness: If this...

Traction Control 娂 active: Flashes when the Traction Control 娂 is active. If the light remains on amalfunction has been detected; havethe system serviced immediately,refer to the Driving chapter for more information. Overdrive off (automatictransmission): Illuminates when the overdrive function of t...

Turn signal: Illuminates when the left or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a burned out bulb. High beams: Illuminates when the high beam headlamps are turned on. Daytime running lamps (DRL)(if equipped): Illuminates when the Day...

GAUGES Base instrument cluster gauges Optional instrument cluster gauges Refer to Message Center (if equipped) in the Driver Controls chapter to select one of six preset colors or one user definable color (MyColor)for the nighttime gauge backlighting. 2006 05+ Mustang (197)Owners Guide (post-2002-fm...

AUDIO SYSTEMS AM/FM stereo/ single CD sound system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches and radio may be used for up to tenminutes after the ignition switch is turned to the OFF position or untilany door or trunk is open...

Balance: Press to adjust the audio between the left and right speakers. Use / / SEEK . Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise....

18. CD eject: Press to eject a CD. 19. CD slot: Insert a CD label side up. SHAKER 500 — Audiophile In-Dash Six CD/MP3 Sound System(if equipped) 2006 05+ Mustang (197)Owners Guide (post-2002-fmt)USA (fus) Entertainment Systems 22

3. Menu: Press to toggle through the following modes: Setting the clock: Press until SELECT HOUR or SELECT MINS is displayed. Press / / SEEK to adjust the hours/minutes. SHAKER (Available with the SHAKER 1000 only): Select to engage SHAKER 1000 mode. SHAKER 1000 mode enhances acoustic sound forall s...

18. LOAD: Press to begin the CD load sequence. When the radioprompts to select a slot, use thepresets to select the desired slot toload the CD. If the selected slotalready contains a CD, the display will read SLOT FULL. Press and holdto autoload up to 6 CDs. Load CDs one at a time when the radioprom...

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from a station, the weakerthe signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thunderstorms ...

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Temperature selection: Controls the temperature of the airflow in the vehicle. 2. Mode selections: Controls the location of the airflow in the vehicle. See the following for a brief description of each selection. MAX A/C: Distributes recirculated air thr...

6. Fan speed adjustment: Controls the volume of air circulated in the vehicle. Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the (defrost) position. • To reduce humidity build up inside the vehicle, do not drive with theairflow selector...

REAR WINDOW DEFROSTER (R ) Ensure that the ignition is in the 3 (ON) position. Press the control toclear the rear window of thin ice and fog. The LED will illuminate. The rear window defroster turns off automatically after 10 minutes, orwhen the ignition is turned to the 1 (OFF/LOCK) position. To ma...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Foglamp control (if equipped) The foglamps can be turned onwhen the ignition is in the ONposition, the headlamp control is inthe or position and the hi...

Flash to pass Pull toward you, to the first detent,to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. When activated, the DRLtelltale is illuminated.To activate: • the ignition must be in the ON position, • the headlamp cont...

If your vehicle has been in an accident the alignment of your headlampsshould be checked by your authorized dealer. Headlamp vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) C...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. The flash rate of the turn signal will speed up considerably if theLighting Control Module detects a left or right turn lamp bulb (front orrear) is burned out. INTERIOR LAMPS Map lamps Press ...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control up oneposition. Adjust the rotary control to thedesired speed setting. For normal or low speed wiperoperation, move control up twopositions from OFF. For high speed wiper operation,move control up three positionsfrom OFF...

Cigarette/Cigar lighter (if equipped) Do not plug optional electrical accessories into the cigarette lightersocket. Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromits heating position when it is ready to...

Express down (One Touch Down, Front windows only) Allows the driver and passenger’swindow to open fully withoutholding the control down. Push theswitch completely down to thesecond detent and release quickly.The window will open fully.Momentarily press the switch to anyposition to stop the windowope...

Bounce Back Override (Front windows only) To override Bounce Back, within 2 seconds after reaching Bounce Backposition, if the switch is moved from the Neutral to the Express Upposition the window will travel up with no bounce back protection. If the switch is released before the window reaches full...

EXTERIOR MIRRORS Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirror...

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control. Turning off speed control There are two ways to turn off the speed control: • Press the speed control OFFcontrol. • Turn OFF the ignition. Note: When you turn off the speed control or the ignition, your spee...

The latch handles must be pulleddownwards fully to allow thelatch to fully rotate into theopen position 3. Unclamp the top from thewindshield header by pulling eachlatch handle down and then rotatingthe latch to the rear until it clearsthe header. Note: If the top has not been lowered for some time ...

Installation of the boot (if equipped) Be sure the boot is secure on the vehicle before driving. 1. Install the boot on the vehicle by hooking the boot retaining clips onthe back panel.2. Install the boot on the right side tucking in the front part of the bootin the quarter panel and hooking the ret...

Storing the boot 1. Position the boot right-side up and fold each side of the boot inward. 2. Turn the boot upside down and fold the left side of the boot inward. 3. Fold the right side inward and secure the boot with the strap. Stow the boot in the trunk. Raising the convertible top The convertible...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status. Thesystem will a...

of the monitored systems, the message center will indicate either an OKmessage or a warning message for two seconds. Pressing the RESET control cycles the message center through each ofthe systems being monitored. The sequence of the system check report and how it appears in themessage center is as ...

3. Press and hold the RESETcontrol to set the language choice. Info menu This control displays the followingcontrol displays: • Odometer • Trip odometer • Distance to Empty • Average Fuel Economy • Instantaneous Fuel Economy • Fuel Used • Trip Elapsed Drive Time • Average Speed • Blank Display Odome...

The DTE function will display LOW FUEL LEVEL and sound a tone forone second when you have approximately 50 miles (80 km) to empty. Ifyou RESET this warning message, this display and tone will returnwithin 10 minutes. DTE is calculated using a running average fuel economy, which is basedon your recen...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

Autolock (if equipped) On vehicles equipped with an automatic transmission, this featureautomatically locks all vehicle doors when: • all doors are closed, • the ignition is in the 3 (ON) position, • the brake is pressed before reaching 5 mph (8 km/h), and • then the vehicle increases to more than 5...

• The driver’s door is unlocked when the key is inserted in the driverdoor key cylinder and turned to the unlock position. The driver’s dooris locked when the key is inserted in the driver door key cylinder andturned to the lock position. Note: Locking the driver door with the key does not lock the ...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...

open, and in 30 minutes if the dome lamp control is left on and theignition has been turned to the 1 (OFF/LOCK) position. The batterysaver will also shut off the trunk lamps in 30 minutes if the trunk is leftopen. SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock 娂 passive anti-theft system is an en...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the1 (OFF/LOCK) position. The theft indicator will flash everytwo seconds when the vehicle isarmed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. • The theft ind...

To program additional new unprogrammed key(s), repeat this procedurefrom Step 1 for each additional key. ACTIVE ANTI-THEFT SYSTEM (IF EQUIPPED) The active anti-theft system is designed to warn you in the event of anunauthorized entry to your vehicle and is also designed to help preventthe unwanted t...

Arming the system When armed, the active anti-theft system is designed to notify you of anunauthorized entry. When unauthorized entry or towing occurs, thesystem will flash the turn signal lamps and interior lamps and sounds thesecurity horn. The system is ready to arm whenever the key is out of the...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Lift the head restraint to raise theheight. To lower the head restraint, pressthe button located on the driver’sside post. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upright and the lapb...

Use the recliner handle to returnthe seatback to the desired position. REAR SEATS 2nd seat/split-folding rear seat One or both rear seatbacks (coupe only) can be folded down to provideadditional cargo space. To lower the seatback(s) frominside the vehicle, pull strap torelease seat back and then fol...

SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and cra...

The front passenger sensing system can automatically turn off thepassenger front airbag. The system is designed to help protect small(child size) occupants from airbag deployments when they areimproperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint us...

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety belt pretensioners, front safety belt buckle sensors, and the driverseat position sensor. In addition, the RCM also monitors the restraintswarning lig...

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on t...

The belt guide is secured to the sideshield by fastening the snap on theguide strap to the snap on the sideshield. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue issecurely fas...

Energy Management Feature • This vehicle has a safety belt system with an energy managementfeature at the front seating positions to help further reduce the risk ofinjury in the event of a head-on collision. • This safety belt system has a retractor assembly that is designed topay out webbing in a c...

This mode should be used any time a child safety seat is installed in a passenger front or outboard rear seating position. Children 12 years oldand under should be properly restrained in the rear seat wheneverpossible. Refer to Safety restraints for children or Safety seats for children later in thi...

After any vehicle collision, the front passenger and rear outboardsafety belt systems must be checked by an authorized dealer to verify that the “automatic locking retractor” feature for child seats isstill functioning properly. In addition, all safety belts should be checkedfor proper function. BEL...

Do not use extensions to change the fit of the shoulder beltacross the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All saf...

Conditions of operation If... Then... The driver’s or frontpassenger’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning lightilluminates1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s or frontpassenger’s safety belt isbuckle...

If... Then... The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2 minuteshave elapsed since the ignitionswitch has been turned ON... The BeltMinder 威 feature will not activate. The driver’s or frontpassenger’s safety belt i...

Do not sit on top of a buckled safety belt to avoid theBeltMinder 威 chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate theBeltMinder 威 feature please follow the directions stated below. One time disable If at any time the driver/fro...

• Step 3 must be completed within 50 seconds after the safety beltwarning light turns off. 3. For the seating position being disabled, at a moderate speed, bucklethen unbuckle the safety belt 9 times, ending in the unbuckled state.(Step 3 must be completed within 50 seconds after the safety beltwarn...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your authorized dealer. Modifying or adding equipment to the front end of the vehicle(including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag syst...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration sufficientto cause the airbag sensors to closean electrical circuit that initiatesairbag inflation. The fact that theairbags did not inflate in a collisi...

• a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness ligh...

• a child or a small person occupies the front passenger seat. For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing systemuses a ⬙ passenger airbag off ⬙ or ...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected bythe collision will be inflated. The front passenger sensing system willturn off the passenger seat side airbag if the seat is empty. The airbagwas des...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS servicedat an authorized dealer immediately. Unless serviced, the system may notfunction properly in the even...

neck, the child should wear the lap and shoulder belt. Moving the childcloser to the center of the vehicle may help provide a good shoulder beltfit. Do not leave children, unreliable adults, or pets unattended inyour vehicle. Child booster seats Children outgrow a typical convertible or toddler seat...

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the stomach, and lets you adjust the shoulder belt to cross thechest and rest snugly near the center of the shoulder. The drawingsbelow compare the ideal fit...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of LATCH anchors refer to Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments in this chapter. Carefully f...

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate itis in the automatic locking mode. 7. Pull the lap belt p...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

Note: The attachments for the convertible boot located on the backof the head restraints are not tetheranchors. 4. Access tether anchors locatedbehind the seatback under the vinyltag marked with the child tetheranchor symbol. 2006 05+ Mustang (197)Owners Guide (post-2002-fmt)USA (fus) Seating and Sa...

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol. The center of the rear seatis NOT designed as a seating position. The LATCHanchors were not designed to beused with a child seat in thecenter position and there is notether anchor av...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

gauges may be inaccurate. Ford Motor Company recommends the use ofa digital or dial-type tire pressure gauge rather than a stick-type tirepressure gauge. Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patt...

To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile. Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is no...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

Never spin the tires in excess of the 35 mph (55 km/h) pointindicated on the speedometer. Highway hazards No matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly to theclosest safe area out of traffic. This may further dam...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. Use chains on the tires only in an emergency or if th...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more detailed information. Do not exceed the GVWR or the GAWR specified on th...

capacity to carry you, 4 of your friends and all the golf bags? You andfour friends average 220 lb. (99 kg) each and the golf bags weighapproximately 30 lb. (13.5 kg) each. The calculation would be: 1400 –(5 x 220) – (5 x 30) = 1400 – 1100 – 150 = 150 lb. Yes, you haveenough load capacity in your ve...

Do not splice into the vehicle lamp wiring for trailer lamps. Yourvehicle uses an advanced electronic module to control andmonitor your vehicle lamps. Splicing into the wiring or attachingwiring to the vehicle bulb. may DISABLE the rear vehicle lampsor cause them not to function properly. See your a...

RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) Follow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as behind arecreational vehicle). These guidelines are designed to ensure that your transmission is notdamaged due to insufficie...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. Note: The ignition key cannot be removed from the ignition unlessthe gearshift lever is securelylatched in P (Park). 2. ACCESSORY, allows the electricalaccessories su...

3. Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (ST...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. (I...

Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your a...

The Traction Control 娂 switch, located above the radio, illuminateswhen the system is off. The TractionControl 娂 system will automatically turn on every time the ignition isturned OFF and ON. If you should become stuck in snowor ice or on a very slippery roadsurface, try switching the TractionContro...

• loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steeringseem to wander/pull. TRACTION-LOK 姟 AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surf...

• To return to Overdrive mode, press the transmission control switch.The O/D OFF lamp will not be illuminated. • Overdrive mode is automatically returned each time the key is turnedoff. 3 (Third) This position allows for third gear only. • Provides engine braking. • To return to D (Drive) without Ov...

Do not rock the vehicle for more than a minute or damage to thetransmission and tires may occur, or the engine may overheat. MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transmission has a starter interlock that prevents crankingthe engine unless the clutch pedal is fully ...

Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 11 mph (18 km/h) 2 - 3 19 mph (31 km/h) 3 - 4 30 mph (48 km/h) 4 - 5 40 mph (64 km/h) Reverse 1. Make sure that your vehicle is at a complete stop before you shift intoR (Revers...

engine or your vehicle may stall. Driving through deep water where the transmission vent tube is submerged may allow water into thetransmission and cause internal transmission damage. Once through the water, always dry the brakes by moving yourvehicle slowly while applying light pressure on the brak...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

• emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in the glove compartment. In Canada,...

FUEL PUMP SHUT-OFF SWITCH FUEL RESET This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. The fuel pump shut-off switch islocated in the dr...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 17 10A Restraint Control Module (RCM),Passenger Occupant Detection System(PODS), Passenger Air bagDeactivation Indicator (PADI) 18 10A Anti-lock Brake System (ABS),Positive Crankcase Ventilation (PCV)valve heater, Ignit...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For v...

How to change a flat tire To help prevent the vehicle from moving when you change a tire,be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of thevehicle) to the tire being changed. If the vehicle slips off the jack, you or som...

Never use the rear differentialas a jacking point. To lessen the risk ofpersonal injury, do not put any part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle is on the jack. The jack isonly meant for changing the tire. 5. Remove the lug nuts with the lug w...

3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other movingparts. 4. Check all battery terminals and remove any excessive corrosion beforeyou attach th...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party mediation/arbitration program administered by the CanadianMotor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relat...

Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide Fre...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

• 4.6L 3V SOHC V8 engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32–A),available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and w...

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material,...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer ca...

2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift inN (Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, p...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power distribution box...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

• 4.0L V6 engine • 4.6L 3V V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the lower hole, add enough oil to raise thelevel within...

• 4.0L V6 engine • 4.6L 3V SOHC V8 engine • Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. 2006 05+ Mustang (197)Owners Guide (post-2002-fmt)USA (fus) Maintenance an...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to scheduled maintenance information for the servi...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

will not affect function or durability of the transmission. Over time theadaptive learning process will fully update transmission operation to itsoptimum shift feel. If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once th...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add antifreeze/coolant that meets the material and designspecifications for your vehicle. Refer to Lubricant specifications in this...

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come outforcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section....

4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Restart the engine and take your vehicle to an authorized dealer. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your veh...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

be void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler ca...

• The indicator may come on. For more information on the “check engine” or the “service engine soon” indicator, refer to Warning lights and chimes in the Instrument Cluster chapter. ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniques Your best source of information about actual fuel economy is you, ...

Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least...

description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may not pass the I/M test with the indicator on. If the vehicle’s powertrain system or its battery has just been serviced,the on-board diagnostics system is reset to a “not ready for I/M test”conditi...

BRAKE/CLUTCH FLUID Brake and clutch systems are supplied from the same reservoir. The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. ...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Note: There are two different manual transmissions used in thisvehicle and they have different fluid levels. For vehicles equipped with aV6 engine the corre...

REFILL CAPACITIES Fluid Ford PartName Application Capacity Brake fluid and(clutch fluid ifequipped) Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid All Between MINand MAX lineson reservoir Engine oil(includes filterchange) 6 Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft ...

6 Use of synthetic or synthetic blend motor oil is not mandatory. Engine oil need only meet the requirements of Ford specificationWSS-M2C929-A (4.0L) or WSS-M2C930-A (4.6L) and the APICertification mark. LUBRICANT SPECIFICATIONS Item Ford part name Ford part number Ford specification Brake fluid and...

Item Ford part name Ford part number Ford specification Disc brake caliper rails Motorcraft Silicone Brake Caliper Grease and Dielectric Compound XG-3-A ESE-M1C171-A Windshield washer fluid Motorcraft Premium Windshield Washer Concentrate ZC-32-A WSB-M8B16-A2 1 Add 4 oz. (118 ml) of Additive Frictio...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ..........................44 Air cleaner filter .......................225 Airbag supplemental restraintsystem ............................94–95, 102 and child safety seats ..............96description ........................95, 102disposal ....................................105dr...