Ford 2006 Fusion v.2- User Manual

Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger airbag. Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about...

Cell phone use The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

Check engine: The Check Engine indicator light illuminates when theignition is first turned to the ONposition to check the bulb. Solidillumination after the engine is started indicates the On BoardDiagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the M...

Anti-lock brake system (ifequipped): If the ABS light stays illuminated or continues to flash, amalfunction has been detected, havethe system serviced immediately byyour authorized dealer. Normal braking is still functional unless the brakewarning light also is illuminated. Airbag readiness: If this...

Speed control: Illuminates when the speed control is engaged. Turnsoff when the speed control systemis disengaged. Door ajar (if equipped): Illuminates when the ignition is inthe ON position and any door ordecklid is open. Anti-theft system: Flashes when the SecuriLock 娂 Passive Anti-theft System ha...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMS AM/FM Single CD/MP3 sound system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped)may be used for up to ten minutes after the ignition is turned off or untileither front door is opened...

If your vehicle is not equipped with an in-dash clock, press MENU until SET HOURS or SET MINUTES appears in the display. Press / to adjust the hours/minutes. Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press...

Setting the clock: If your vehicle is equipped with an in-dash clock, refer to Clock in the Driver Controls chapter for instructions on how to set the time.If your vehicle is not equipped with an in-dash clock, press MENU untilSET HOURS or SET MINUTES appears in the display. Press / to adjust. RBDS ...

Track/Folder Mode: Available only on MP3 discs in CD mode. Press / to toggle between Track and Folder mode. In Track Mode, press SEEK to scroll through all tracks on the disc.In Folder mode, press SEEK to scroll through tracks in the selected folder. Compression: Brings soft and loud CD passages tog...

18. LOAD: Press to load a CD. Press LOAD and a memory presetto load to a specific slot. Press andhold to autoload up to six CDs. 19. CD eject: Press to eject the current CD. To eject a specific CD,press Eject and the correspondingmemory preset. Press and hold to autoeject all discs in the system. If...

CD/CD player care: Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleanerand wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circul...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop. AUTOMATIC TEMPERATURE CONTROL (ATC) SYSTEM(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center, ...

• To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control....

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of theheadlamp...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. INTERIOR LAMPS Dome lamps and map lamps The map lamps are located on theoverhead console. Press the controlsto turn on the lamps. Your vehicle may also have readinglamps within the rear dome ...

9. Tuck the 2 lead wires into the lamp housing to assure that they arenot pinched when installing the protective rubber cap. 10. Install the protective rubber cap to the housing circular ring bypushing and pressing it forward. 11. Re-apply pressure around the complete circular ring on the housingto ...

Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb tobreak the next time the headlamps are operated. 12. After the new bulb is installed, carefully let the bulb sock...

Replacing foglamp bulbs (if equipped) 1. Make sure the foglamp switch isin the OFF position. 2. From underneath the vehicle,partially remove the tire splashshield by removing four drivescrews. After removing to allow free accessto the front fog lamp bulb andelectrical wire harness, the splash shield...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is set on the intermittent settings, the speed of the wipers will automatically ...

TILT/TELESCOPE STEERING WHEEL To adjust the steering wheel: 1. Pull the lever down to unlock thesteering column. 2. While the lever is in the downposition, move the steering wheelup or down and in or out until youfind the desired position. 3. While holding the steering wheelin place, pull the lever ...

Use only soft cups in the cupholder. Hard objects can injure youin a collision. INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may beused to secure sunglasses or similarsized objects. Press the control toopen the storage compartment. AUXILIARY POWER POINT (12VDC) Power outlets are desi...

Improper use of the lighter can cause damage not covered by yourwarranty. POWER WINDOWS Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are freeof obstruct...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press theright side of the control. Press theleft side to restore the windowcontrols. AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle...

Turning off speed control There are two ways to turn off the speed control: • Press the speed control OFFcontrol. • Turn OFF the ignition. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control feat...

In any mode: • Press VOL + or - to adjust thevolume. Climate control features Press TEMP + or - to adjusttemperature. Press FAN + or - to adjust fanspeed. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up(from the closed position) to ventilate the vehicle....

To open the moon roof: The moon roof is equipped with anautomatic, one-touch, expressopening, closing and venting feature.Press and release the rear portion ofthe control. To stop motion at anytime during the one-touchoperation, press the control asecond time. When closing the moon roof, you should ...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the RUNposition, the message center,located on your instrument cluster,displays important vehicleinformation through a constant monitor of vehicle systems. You may select display features on the message center for a display of statuspreceded by a bri...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and a remote keyless entrytransmitter. Your IKTs are programmed to your vehicle; using a non-programmed keywill not permit...

Note: Your vehicle’s IKTs were issued with an adhesive securitylabel on them that providesimportant vehicle key cutinformation. It is recommended thatyou maintain the label in a safeplace for future reference, such asthe inside front cover of this Owner’s Guide. RECOMMENDED HANDLING OF THE INTEGRATE...

Likewise, when rotating the IKT tothe 1 (LOCK) position in theignition lock cylinder, the bottomedge of the IKT adjacent to thecontrol can be utilized. POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Smart locks This feature attempts to help prevent y...

Power door lock/unlock inhibit feature As a theft deterrent, the power door lock controls and the interior trunkrelease control can be disabled 20 seconds after the ignition has beenturned to the 1 (LOCK) position and the vehicle is locked using any ofthe following: • Remote entry transmitter portio...

To open the luggage compartmentdoor (lid) from within the luggagecompartment, pull the illuminated“T” shaped handle and push up onthe trunk lid. The handle iscomposed of a material that willglow for hours in darkness followingbrief exposure to ambient light. The “T” shaped handle will belocated eith...

interference, and (2) This device must accept any interference received,including interference that may cause undesired operation. Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment. The typical operating ran...

How to reprogram your Integrated Keyhead Transmitters (IKTs) To program a new Integrated Keyhead Transmitter yourself, refer to Programming spare keys in the SecuriLock 娂 passive anti-theft section of this chapter. Note: At least two IKTs are required to perform this procedure yourself. Illuminated ...

You may also perform the following power door lock sequence toenable/disable the perimeter lamps feature. Note: Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed.You must complete Steps 1–5 within 30 seconds or the procedure willhave to be repeated. If...

• If the courtesy lamps were turned on because one of the vehicle doorsor the trunk was opened, the battery saver will shut off them off 10minutes after the ignition has been turned to the 1 (LOCK) position. • The battery saver will shut off the headlamps 10 minutes after theignition has been turned...

• by using a power door unlock/lock sequence. Note: The autolock feature can be activated/deactivated independently of the autounlock feature. Before starting, ensure the ignition is in the 1 (LOCK) position and allvehicle doors are closed. You must complete Steps 1–5 within 30 secondsor the procedu...

1. Place the key in the ignition andturn the ignition to the 3 (RUN)position. 2. Press the power door unlockcontrol on the door panel threetimes. 3. Turn the ignition from the 3(RUN) position to the 1 (LOCK)position. 4. Press the power door unlock control on the door panel three times. 5. Turn the i...

Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the samekey chain may cause vehicle starting issues. You need to prevent theseobjects from touching the coded IKT while starting the engine. Theseobjects will not cause dama...

Replacement Integrated Keyless Transmitters (IKT) and coded keys Note: Your vehicle comes equipped with two Integrated Keyhead Transmitters (IKTs). The IKT functions as both a programmed ignitionkey that operates all the locks and starts the vehicle, as well as a remotekeyless entry transmitter. A m...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle fromunauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL Integrated Keyhead Transmitters are brought to the authorized dealer to aid in troubleshooti...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter portion ofyour Integrated Keyhead Transmitter. • Unlock the driver’s door with a key. Turn the key full rearward(toward the rear of the vehicle) to ensure the alar...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Using the manual lumbar support (if equipped) The lumbar control is located on theside of the seat cushion. Turn to adjust lumbar support. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upri...

Pull lever up to adjust seatback. Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks t...

Press the switch in the direction ofthe arrows to move the seatforward, backward, up or down. Heated seats (if equipped) The heated seat control is located on the climate control system. Referto the Climate controls chapter. REAR SEATS Split-folding rear seatbacks One or both rear seatbacks can be f...

Front passenger sensing system For airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants that are very closeto the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the...

Safety belt precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passe...

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movem...

This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children12 years old and under should be properly restrained in the rear seatwhenever possible. Refer to Safety restraints for children or Safety seats for children lat...

hardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collision be replaced. However, if the collision was minor and anauthorized dealer finds that the belts do not show damage and continueto operate properly, th...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

National Highway Traffic Safety Administration (NHTSA)recommends a minimum distance of at least 10 inches (25 cm) between an occupant’s chest and the driver airbag module. Never place your arm over the airbag module as a deployingairbag can result in serious arm fractures or other injuries. Steps yo...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• a readiness light and tone • and the electrical wiring which connects the components • Side curtain airbag system. Refer to Side curtain airbag system later in this chapter. • Front passenger sensing system. Refer to Front passenger sensing system. later in this chapter. • “Passenger airbag off” o...

For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. • a child or a small person occupies the front passenger seat and thechild or small person is unbuckled. The front passenger sensing...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a back-up tone to indicate the condition of t...

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided. How does the side airbag system work? The design ...

The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of the type sufficient to cause activation. Side airbags are designedto inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-fro...

All occupants of the vehicle, including the driver, should alwayswear their safety belts even when an inflatable curtain is provided. To reduce the risk of injury, do not obstruct or place objects inthe deployment of the inflatable curtain. How does the side air curtain system work? The design and d...

The side air curtains are mounted to the sheet metal above the first andsecond row seats. In certain lateral collisions, the air curtain andseat-mounted side airbag on the side affected by the collision will beinflated, even if the respective seat is not occupied. The air curtain wasdesigned to infl...

Any difficulty with the system is indicated by one or more of thefollowing: • The readiness light (same light as used for front airbag system) willeither flash or stay lit. • The readiness light will not illuminate immediately after ignition isturned to the RUN position. • A series of five beeps wil...

Children and safety belts If the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as specified by your child safetyseat manufacturer) should always wear safety belts. Follow all the important safety restraint and airbag precautions that...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Use a tire gauge to check the tire inflation pressure, including the spare(if equipped), at least monthly and before long trips. You are stronglyurged to buy a reliable tire pressure gauge, as automatic service stationgauges may be inaccurate. Ford Motor Company recommends the use ofa digital or dia...

Age Tires degrade over time, even when they are not being used. It is recommended that tires generally be replaced after 6 years of normalservice. Heat caused by hot climates or frequent high loadingconditions can accelerate the aging process.You should replace the spare tire when you replace the ot...

It is recommended that the two front tires or two rear tires generally bereplaced as a pair. Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not...

Front wheel drive (FWD) vehicles and those with an independent rearsuspension (if equipped) may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recom...

Note: You may not find this information on all tires because it is not required by federal law. 7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. Follow these guidelines when us...

VEHICLE LOADING This section will guide you in the proper loading of your vehicle to keepyour loaded vehicle weight within its design rating capability. Properlyloading your vehicle will provide maximum return of vehicle designperformance. Before loading your vehicle, familiarize yourself with thefo...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2006 Fusion (fsn) Owners Guide (post-2002-fmt)US...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Do not exceed the GVWR or the GAWR specified on the SafetyCompliance Certification Label. Do not use replacement tires with lower load carrying capacitiesthan the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than theoriginals do not ...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fol...

RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a recreational vehicle ormoving truck). In case of roadside emergency with a disabled vehicle, please refer to the Wrecker towing section in the Driving chapter...

STARTING Positions of the ignition 1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and all electricalaccessories off without locking thesteering wheel. To lock the steeringwheel, remove the key then turn thesteering wheel. 2. ACC, allow...

Starting the engine 1. Turn the key to 3 (RUN) withoutturning the key to 4 (START). 2. Turn the key to 4 (START), thenrelease the key as soon as theengine starts. Excessive crankingcould damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to LOCK...

BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-outand should be inspected by an authorized dealer. If the vehicle hascontinuous vibration or shudder in the steering wheel while braking, thevehicle ...

Using ABS When hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since this will reduce theeffectiveness of the ABS and will increase your vehicle’s stoppingdistance. The ABS will be activated immediately, allowing you to retainfull steering control duri...

During Traction Control 娂 operation, the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine compartment, and theengine may not “rev-up” when youpush further on the accelerator. This is normal system behavior andshould be no reason for conc...

To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transaxle has a starter interlock that prevents cranking theengine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put t...

2. Move the gearshift lever into the neutral position and wait at leastthree seconds before shifting into R (Reverse). • The gearshift lever can only be moved into R (Reverse) by moving itfrom left of 3 (Third) and 4 (Fourth) before shifting into R (Reverse).This is a lockout feature that protects t...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER CONTROL The hazard flasher is located on theinstrument panel by the radio. Thehazard flashers will operate whenthe ignition is in any position or ifthe key is not in the ignition. Push in the flasher control and allfront and rear direction signals will flash. Press the flasher control...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electri...

• Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocatio...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

2. Remove the center ornament (ifequipped) from the wheel. Looseneach wheel lug nut one-half turncounterclockwise but do not removethem until the wheel is raised offthe ground. 3. Put the jack in the jack locatornext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is compl...

7. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torquespecification. 8. Unblock the wheels. Stowing the wheel and jack 1. Fully collapse the jack and place it back in the storage area in the...

When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc thatcontacts the wheel. Ensure that any fasteners that attach the rotor tothe hub are secured so they do not interf...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party mediation/arbitration program administered by the CanadianMotor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relat...

For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide French Owner...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as g...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

• 3.0L DOHC engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use ...

may cause squeaking or chatter noise from the blades, and streaking andsmearing of the windshield. To clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned witha non-abrasive cleaner such as Motorcraft Ultra-Clear Spray GlassCleaner (ZC-23), available f...

• Do not use household or glass cleaners as these may damage thefinish. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional StrengthCarpet & Up...

UNDERBODY Flush the complete underside of your vehicle frequently. Keep body anddoor drain holes free from packed dirt. FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequ...

SERVICE RECOMMENDATIONS To help you service your vehicle we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Owner Informati...

2. Block the wheels. To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake/Clutch fluid reservoir 5. Transmission fluid dipstick (if equipped) 6. Battery 7. Power distribution box 8. Air filter assembly 9. Power steering fluid...

3.0L DOHC V6 Duratec engine 1. Engine coolant reservoir 2. Power steering fluid reservoir 3. Brake fluid reservoir 4. Transmission Fluid Dipstick 5. Battery 6. Power distribution box 7. Air filter assembly 8. Engine oil dipstick 9. Engine oil filler cap 10. Windshield washer fluid reservoir 2 1 10 7...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has man...

• 3.0L DOHC V6 Duratec engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. On 2.3L I4 engine, be sure thenotch in the indicator flange isaligned with the V on the enginewhen reinserting it. • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • If the oil level is within t...

• 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter....

• 2.3L I4 engine • 3.0L DOHC V6 Duratec engine • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. On 2.3L...

5. Fully install the engine oil filler cap by turning the filler cap clockwiseuntil it stops. To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed. Engine oil and filter recommendations Look for this certificationtrademark...

that does not meet Ford material and design specifications, start-upengine noises or knock may be experienced. It is recommended you usethe appropriate Motorcraft oil filter (or another brand meeting Fordspecifications) for your engine application. BATTERY Your vehicle is equipped with aMotorcraft m...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, maydarken the color of Motorcraft Premium Gold Engine Coolant fromyellow to golden tan. Note: When adding more than 1 quart (.95L) of coolant it is necessary to use the coolant...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine c...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If...

• The indicator may come on. For more information on the “check engine” or the “service engine soon” indicator, refer to Warning lights and chimes in the Instrument Cluster chapter. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you,...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If the indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may no...

• 3.0L V6 Engine 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right severaltimes. 3. Turn the eng...

TRANSAXLE FLUID Checking 5–speed automatic transaxle fluid (If equipped) Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transaxle does not consumefluid. However, the fluid level should be checked if the transaxle is notworking properly, i.e...

The transmission fluid should be inbetween the notches if at normaloperating temperature 149°F(65°C). High fluid level Fluid levels above the safe rangemay result in transaxle failure. Anoverfill condition of transmissionfluid may cause shift and/orengagement concerns and/orpossible damage. High flu...

Checking and adding manual transmission fluid (if equipped) 1. Park the vehicle on a levelsurface. 2. Engage the parking brake fully –put in first gear. 3. Assure the vehicle cannot move. 4. Clean the filler plug. 5. Remove the filler plug andinspect the fluid level. 6. Fluid level should be at bott...

Changing the air filter element • 2.3L I4 engine • 3.0L DOHC V6 Duratec engine 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. • 2.3L I4 engine 2006 Fusion (fsn) Owners Guide (post-2002-fmt)USA (fus) Maintenance and Spec...

For PCV valve replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material anddesign specifications for your vehicle, such as a Motorcraft orequivalent replacement...

Fluid Ford Part Name Application Capacity Engine coolant 2 MotorcraftPremium GoldEngine Coolant(yellow-colored) 2.3L I4 enginewith automaticor manualtransaxle 8.56 quarts(8.1L) 3.0L V6 Duratecengine withautomatictransaxle 9.72 quarts(9.2L) Transmissionfluid Motorcraft SAE75W-90 gear oil(non-syntheti...

TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find atransmission/transaxle code on theSafety Compliance CertificationLabel. The following table tells youwhich transmission or transaxleeach code represents. Description Code 5–Speed Manual Transaxle A Mazda G5M 5 5–Speed Automatic Transaxle Mazda F...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ..........................53 Air cleaner filter ...............240–242 Air conditioning ....................29, 31 Airbag supplemental restraintsystem ........................108, 117, 120 and child safety seats ............110description ..............108, 117, 120disposal ..........