Ford 2006 Freestyle v.2- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

• where the driver was positioning the steering wheel. To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or wher...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Check fuel cap (if equipped): Illuminates when the fuel cap maynot be properly installed. Continueddriving with this light on may causethe Check engine warning light tocome on, refer to Fuel filler cap in the Maintenance and Specification chapter. Brake system warning light: To confirm the brake sys...

Speed control: Illuminates when the speed control is engaged. Turnsoff when the speed control systemis disengaged. Low washer fluid (if equipped): Illuminates when the windshieldwasher fluid is low. Door ajar (if equipped): Illuminates when the ignition is inthe ON position and any door ordecklid is...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMS AM/FM stereo/ single CD sound system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches and radio may be used for up to tenminutes after the ignition switch is turned off or until either front door isopened. 1. / Tuner: ...

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors:...

Audio system warranty and service Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician. Navigation system (if equipped) Your vehicle may be equipped with a Navigation System. Refer to the Navigation supplement for further...

2. PLAY/PAUSE control Press to playback or pause the DVD. 3. DIM control Press (+) to increase or (-) to decrease the brightness on the screen. 4. ENTER control Press to select the function highlighted on the active menu. ENTER mayalso be used by some user interactive discs during movie play. 5. MEN...

• Press the NEXT control to movethe cursor one position upward • Press the PREV control to movethe cursor one position downward • Press the REV control to movethe cursor left one position • Press the FWD control to movethe cursor right one position Next/Previous control The NEXT (up) and PREV (down)...

Remote control 1. REV (REVERSE) control Press to reverse the direction of the DVD movie. 2. FWD (FORWARD) control Press to advance the direction of the DVD movie. 3. PLAY/STOP control When playing, press PLAY/STOP to stop the disc. When stopped, pressPLAY/STOP to play the disc. 4. SEEK control Press...

Playback and format • The DVD player of your Family Entertainment DVD System can onlybe used in the “playback” mode. (The DVD player does not offer arecord feature.) • The system plays standard CDs, DVDs and also plays most CD R/W,DVD R/W, VCD and MP3 media. Saving MP3 files • Your Family Entertainm...

2. Connect the left and right audio lines to the WHITE (left) and RED(right) auxiliary input jacks respectively. 3. Press the MODE control repeatedly until DVD/CD AUX (no disc inplayer) or DVD/CD play (disc in player) illuminates in the radio display.If a disc is in the system, playback should begin...

Safety information Read all the safety and operating instructions before operating thesystem and retain for future reference. • Do not attempt to service, repair or modify the Family EntertainmentDVD System. See your Ford or Lincoln Mercury dealer. • Do not insert foreign objects into the DVD compar...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/decrease the airflow...

Dual Zone Automatic Temperature Control with heated seats(if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/de...

Dual Zone Automatic Temperature Control with rear passengercompartment climate control (if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Rear temperature cont...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theairflow selector in the OFF or with recirculated air engaged. • Do not put objects under the front seats ...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamp switch to . The headlamps will turn off. Foglamp control (if equipped) With the ignition on, the foglampscan be turned on when theheadlamp control is pulled towardyou and is in any of the foll...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF, autolamps or parking lampposition and • the transmission must be out of the Park position. Always remember to turn on ...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control up oneposition. Adjust the rotary control to thedesired speed setting. Mist function: To activate mist, push control down from the OFFposition and release to get one wipe. For normal or low speed wiperoperation, move con...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: 2 — Three to four second intervalrear wiper. 1 — Ten second interval rear wiper. O — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) ...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamp. The visor willslide back and forth on the rod forincreased sunlight coverage. Slide on rod feature Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage. Note: To st...

Storage compartment Press the latch to open the storagecompartment. The door will openslightly and can be moved to fullopen. The storage compartment may beused to secure sunglasses or asimilar object. Conversation mirror (if equipped) The conversation mirror allows the driver to view the rear seatin...

Second row center console features (if equipped) The second row center consoleincorporates the following features: • Utility compartment • Cupholders • Flip forward armrest to provide aflat load floor Use only soft cups in thecupholder. Hard objects can injure you in a collision. AUXILIARY POWER POI...

Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromits heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by yourwarranty. POWER WINDOWS Do not leave child...

To operate ONE TOUCH UP: • Pull the switch completely up tothe second detent and releasequickly. The driver’s window willclose fully. Momentarily press theswitch to any position to stop theone touch up. If the switch is pressed and held tothe normal open or ONE TOUCH DOWN position during a ONE TOUCH...

Accessory delay With accessory delay, the radio, Family Entertainment DVD System (ifequipped), power windows, and moonroof (if equipped) operate for upto ten minutes after the ignition switch is turned from the ON to theOFF position or until one of the front doors are opened. AUTOMATIC DIMMING INSID...

Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a ...

Memory feature (if equipped) The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features when a memory position is selected through theremote entry transmitter, keyless entry keypad or memory switch on thedriver’s...

STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control features • Press MEDIA to select AM, FM1,FM2, or CD (if equipped). In Radio mode: • Press SEEK to access thenext/previous strong station. In CD mode: • Press SEEK to listen to the nexttrack on the disc. In any mode: • Press VOL up or down to adjustt...

Do not use the HomeLink 威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required byU.S. federal safety standards (this includes any garage door openermodel manufactured before April 1, 1982). A garage door which cannotdetect an object, signaling t...

Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink 威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2outlined in the “Programming” section, replace Step 3 w...

Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the train...

Selectable features Reset Press this control to select and reset functions shown in the INFO menuand SETUP menu. Info menu This control displays the followingcontrol displays: • Odometer • Distance to Empty • Average Fuel Economy • Trip Odometer • Fuel Used • Trip Elapsed Drive Time • Compass Odomet...

LOW FUEL LEVEL. Displayed as an early reminder of a low fuel condition. CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessorieswhen the engine is idling at a low speed, turn off as many of theelectrical loads as possi...

To reset the oil life to 100% with system warnings CHANGE OILSOON/OIL CHANGE REQUIRED displayed: 1. Select this function from theSETUP control for current displaymode. 2. Press and release the RESETcontrol to display “IF NEW OILHOLD RESET”. 3. Press and hold the RESETcontrol to display OIL LIFE SET ...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

1. Place the key in the ignition and turn the ignition to the 3 (RUN)position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn ...

The remote entry system activates the illuminated entry feature; thisfeature turns on the lamps for 25 seconds or until the ignition is turnedto the 3 (RUN) position. The inside lights will not turn off if: • they have been turned on using the dimmer control or • any door is open. The battery saver ...

Activating the memory seat feature To activate this feature: 1. Position the seat, mirrors and adjustable pedals to the positiondesired. 2. Press the SET control on thedriver’s door panel. 3. Within 5 five seconds, press the 1or 2 control on the driver’s doorpanel to which you would like toassociate...

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correct orientation of the battery. Press the batterydown to ensure that the battery is fully seated ...

4. The doors will lock, then unlock, to confirm that the programmingmode has been activated. 5. Within 20 seconds press any button on the remote entry transmitter tobe programmed. Note: If more than 20 seconds have passed you will need to start the procedure over again. 6. The doors will lock, then ...

To lock all doors and liftgate, press the 7 • 8 and the 9 • 0 at the same time. Note: The driver’s door must be closed. You do not need to enter the keypad code first. Autolock The autolock feature will lock all the doors and liftgate when: • all the doors and liftgate are closed, • the ignition is ...

7. Turn the ignition to the 1 (LOCK) position. The horn will chirp onceto confirm the procedure is complete. Keyless entry key pad procedure 1. Turn the ignition to the 1 (LOCK) position. 2. Close all the doors and liftgate. 3. Enter factory-set 5–digit entry code. 4. Press and hold the 7 • 8. While...

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is in the 1(LOCK) position, the indicatorwill flash once every 2 seconds toindicate the SecuriLock 娂 system is functioning as a theft deterrent. • When the ignition is in the 3 (RUN) positio...

• Press the driver or passengerinterior door lock control whilethe door is open, then close thedoor. • Press the 7 • 8 and 9 • 0 controls on the keyless entry pad at thesame time to lock the doors(driver’s door must be closed). There is a 20 second countdownwhen any of the above actions occurbefore ...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Push release button to lower headrestraint. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Lift handle to move seat forward orbackward. ...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

The indicator light on the control will illuminate when activated. For lowheat, one light will be lit; for high heat, both lights will be lit. The heating of the seat turns off after 10 minutes or when the vehicle isturned off. Memory seats/power mirrors/adjustable pedals (if equipped) This system a...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

To return the seatback to theupright position • Lift the seatback toward the rearof the vehicle, and • Rotate the seatback until youhear a click, locking it in theupright position. Note: The seatback will not raise if the rear latch hooks are notproperly engaged to the floorstriker. • Pull the head ...

Stowing the third row bench or split bench seat (if equipped) 1. Stow the head restraints bypushing the head restraint releasebuttons while sliding the headrestraints fully down. Remove allobjects from the seat and stowagetub. 2. From the rear of the vehicle, fold seatback by pulling and holding the...

Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System 娂 to tailor the deployment level of the driver dual-stage airbag based on seatposition. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower air...

Safety belt precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passe...

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have twotypes of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movem...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recom...

Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front safety belt buckleass...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The instrument panel grab handle should never be used forstorage. The path of an inflating airbag must be kept clear at all times. The airbag supplemental restraint system (SRS) is designed to work inconjunction with the safety belts to help protect the dri...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. Do not place any object between an occupant and an airbag orne...

• Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to s...

Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a back-up tone to indicate the condition of thesystem. Refer to the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the ai...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness light, the airbagback up power an...

that the front passenger frontal airbag is disabled. The indicator lamp islocated in the center stack of the instrument panel above the radio. Note : The indicator lamp will illuminate for a short period of time when the ignition is turned to the ON position to confirm it is functional. When the fro...

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided. How does the side airbag system work? The design ...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, i...

Do not attempt to service, repair, or modify the Safety Canopy 娂 system, its fuses, the A, B, C or D pillar trim, or the headliner on a vehicle containing a Safety Canopy 娂 . See your authorized dealer. All occupants of the vehicle including the driver should alwayswear their safety belts even when ...

If the Safety Canopy 娂 system has deployed, the Safety Canopy 娂 will not function again unless replaced. The Safety Canopy 娂 system (including the A, B, C, and D pillar trim) must be inspected and serviced by an authorized dealer. If the Safety Canopy 娂 is not replaced, the unrepaired area will incr...

require that children use approved booster seats until they are eightyears old. Check your local and state or provincial laws for specificrequirements regarding the safety of children in your vehicle. Whenpossible, always place children under age 12 in the rear seat of yourvehicle. Accident statisti...

Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend comfortably. Booster seats may also make the shoulder belt fitbetter and more comfortably. Try to keep the belt near the middle of theshoulder. When ...

• Those with a high back. If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Either type can be used at any seating position equipped withlap/shoulder belts if your child is over 40 lb. (18 k...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward. There should ...

Rear seating positions Follow Steps 1–7 as described above for the following available seats: • 2nd row bucket (40/40) • 2nd row bench (60/40) • 3rd row bench Note : The cargo tie-downs at the rear edge of the floor are nottether anchors. For additional important safety information on the proper use...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Use a tire gauge to check the tire inflation pressure, including the spare(if equipped), at least monthly and before long trips. You are stronglyurged to buy a reliable tire pressure gauge, as automatic service stationgauges may be inaccurate. Ford Motor Company recommends the use ofa digital or dia...

Age Tires degrade over time, even when they are not being used. It is recommended that tires generally be replaced after 6 years of normalservice. Heat caused by hot climates or frequent high loadingconditions can accelerate the aging process.You should replace the spare tire when you replace the ot...

It is recommended that the two front tires or two rear tires generally bereplaced as a pair. Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not...

Front wheel drive (FWD) vehicles and those with an independent rearsuspension (if equipped) may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recom...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. Follow these guidelines when using snow tires and chains: • Use only SAE class “S” cables or equivalent on the front axle forP215/65R17 equipped...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Maximum Loaded Trailer Weight – is the highest possible weight of a fully loaded trailer the vehicle can tow. It assumes a vehicle with onlymandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver ...

The following gives you a few examples on how to calculate the availableamount of cargo and luggage load capacity: • Another example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You decide to go golfing. Is there enough loadcapacity to carry you, 4 of your friends and all th...

Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at theGVWR not GCWR. Trailer lamps Trailer la...

• After you have traveled 50 miles (80 km), thoroughly check yourhitch, electrical connections and trailer wheel lug nuts. • To aid in engine/transmission cooling and A/C efficiency during hotweather while stopped in traffic, place the gearshift lever in P (Park). • Vehicles with trailers should not...

STARTING Positions of the ignition 1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and all electricalaccessories off without locking thesteering wheel. To lock the steeringwheel, remove the key then turn thesteering wheel. 2. ACC, allow...

• Make sure the gearshift lever is inP (Park). 3. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn t...

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If ...

Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control during emergency stops bykeeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking ...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

detecting and controlling wheel spin. The system borrows many of theelectronic elements already present in the anti-lock braking system(ABS). Wheel-speed sensors allow excess wheel spin to be detected by theTraction Control 娂 portion of the ABS computer. Excess wheel spin is controlled through engin...

• Some noise is normal during operation. If the noise is excessive, checkfor low power steering pump fluid level before seeking service by yourauthorized dealer. • Heavy or uneven steering efforts may be caused by low power steeringpump fluid level. Check for low power steering pump fluid level befo...

This system is not designed to prevent contact with small ormoving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damagingthe vehicle. The system may not detect smaller objects, particularlythose close to the ground. Certain a...

indicator light on the control will illuminate when the system is turnedoff. If the indicator light illuminates when the RSS is not turned off, itmay indicate a failure in the RSS. Keep the RSS sensors (located on the rear bumper/fascia) freefrom snow, ice and large accumulations of dirt (do not cle...

Do not use L (Low) gear when driving through sand. Under severe operating conditions, the A/C may cycle on and off toprotect overheating of the engine. Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slip...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for th...

• emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in the glove compartment. In Canada,...

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the enginewhen your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switchmay have been activated. The fuel pump shut-off switch islocated in the front passeng...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — — — 30A Green Green Green Pin...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F15 10A Delayed accessory (Driver windowmotor logic, Auxiliary climatecontrol switch illumination,Moonroof, Audio, Driver door lockswitch illumination) F16 10A Rear defroster indicator, Heatedmirrors F17 30A Rear defros...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electri...

• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheel The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driv...

1. Remove the carpeted floor panellocated in the rear of the vehicle,remove the wing nut that securesthe spare tire by turning itcounterclockwise. 2. Lift and remove the spare tirefrom the trunk. 3. Remove the second wing nut thatsecures the jack retention bracketby turning it counterclockwise,remov...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Take care toposition the jack as shown to ensurethat the locating holes in the jackbase can be placed on the locatingtabs of the jack mounting brack...

If you are stowing the flat tire, remove the “L”-shaped bolt from thelarge wing nut used to secure thespare tire in the vehicle. With the3rd row seat in the raised position,stand the flat tire in the rear of thevehicle with the tire’s valve stemfacing the rear of the vehicle.Fasten the flat tire to ...

JUMP STARTING The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your vehicle. Automatictrans...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellan...

INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then with a clean, drycloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A). • Do not use household or glass cleaners as these may damage thefinish. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equi...

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleather conditioners. These products may cause premature wearing ofthe clear, protective coating. Note: In some instances, color or dye transfer can occur w...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer ca...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood and support it withthe prop...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has many sharp edges and can damage the micro edge of thewiper rubber element. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance ...

6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. • If required, add...

3. Recheck the engine oil level. Make sure the oil level is not above thenormal operating range on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwiseuntil it stops. To avoid...

It is recommended you use the appropriate Motorcraft oil filter (oranother brand meeting Ford specifications) for your engine application. BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling ...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (an opaque plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine c...

• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine damage. • Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine...

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce st...

3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on thefiller pipe. 5. Turn the filler cap clockwise 1/4 of a turn until it clicks at least once. If the indicator comes on and stays on after you start the engine, the fuel filler c...

Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to ...

For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling,an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than t...

3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter. These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly tightening the fuel cap. After threedriving cycles without these or any other temporary malfunctions...

other than the recommended fluid, may affect transaxle operationand result in damage to internal transaxle components. Refer to your scheduled maintenance information for scheduled intervals for fluid changes. Your transaxle does not consume fluid.However, the fluid level should be checked if the tr...

2 For spark plug replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the spark plugs. Replace the spark plugs with ones that meet Ford material anddesign specifications for your vehicle, such as Motorcraft orequivalent replac...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Security systems - vehicle perimeter protection For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight capacity of the veh...

A Accessory delay ..........................68 Air cleaner filter .......................270 Air conditioning ........42, 44, 46, 49 Airbag supplemental restraintsystem ................132–133, 141, 143 and child safety seats ............134description ..............133, 141, 143disposal ..............