Ford 2006 Focus - Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

converter. Drive in a moderate fashion (avoid heavy acceleration anddeceleration) and have your vehicle serviced immediately by yourauthorized dealer. Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or oth...

Airbag readiness: If this light fails to illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately by your authorized dealer. A chime will also sound when amalfunction in the supplemental restraint system has been detected. Safety belt: Reminds you...

Traction Control 娂 system (if equipped): Illuminates when the Traction Control 娂 is turned OFF and will flash when active. If thelight remains on, have the systemserviced immediately, refer to the Driving chapter for more information. Low fuel: Illuminates when the fuel level in the fuel tank is at ...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range. If it enters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, s...

AUDIO SYSTEMS AM/FM stereo with single CD — Premium (if equipped) AM/FM stereo with single CD/MP3 — Premium (if equipped) 2006 Focus (foc) Owners Guide (post-2002-fmt)USA (fus) Entertainment Systems 16

Speed sensitive volume: Radio volume automatically adjusts according to vehicle speed to compensate for road and wind noise. Press the Tune selector ( / ) or SEEK to turn off or select rates 1 through 7. Rate 7 compensates the most volume at higher speeds. Setting the clock: Upon initial battery con...

16. ON/OFF/Volume: Press to turn ON/OFF; turn to increase/decreasethe volume levels. If the volume isset above a certain level and theignition is turned off, for at least aminute, the volume will come backon at a “nominal” listening level when the ignition switch is turned backon. 17. CD: Press to e...

• Station overload: When you pass a broadcast tower, a stronger signalmay overtake a weaker one and play while the weak station frequencyis displayed. CD/CD player care Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approve...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Air flow selections: Controls the direction of the airflow in thecabin. See the following for a briefdescription on each control. : Distributes air through the instrument panel vents. : Distributes air through the instrument panel vents and the floorvents. : Distri...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents toward the side windows. To increase airflow to the outer instrument panel vents, clos...

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice andfog. • A small LED will illuminate whenthe rear defroster is activated. The ignition must be in the ONposition to operate the rear window defr...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. High beams Pull the lever towards you toactivate. Pull the lever towards youagain to deactivate. Flash to pass Pull toward you slightly to activateand ...

Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on when the headlampcontrol is in the or the position and the high beams are notturned on. Pull headlamp control towards youto turn foglamps on. The foglampindicator light will illuminate. PANEL D...

Reading lamps (if equipped) The reading lamps are operated byseparate on/off controls. Theater dimming: The dome lampdims about 20 seconds after thedoors are closed. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize pressure. When moist air entersthe headlamp(s) through the...

Function Trade number License plate lamp C-5W High-mount brakelamp W5W Dome lamp (front/rear) 12V10W Map lamp 12V6W Luggage compartment 12V10W To replace all instrument panel lights - see your authorized dealer Replacing headlamp bulbs 1. Make sure the headlamp controlis in the OFF position and open...

Replacing side marker bulbs 1. Make sure the headlamp controlis in the OFF position. 2. Remove the front shield from thebumper. 3. Reach under the front fender,grasp the bulb socket and turn itcounterclockwise to remove it. 4. Pull the bulb straight out. Install in reverse order. Replacing high-moun...

MULTI-FUNCTION LEVER Windshield wiper: Move the lever down for a single wipe. For intermittent operation, movecontrol up one position and adjustthe rotary control to the desiredspeed. For normal operation, move controlup two positions. For high speed operation, move control up three positions. Mist ...

TILT AND TELESCOPE STEERING COLUMN (IF EQUIPPED) Pull the locking lever down to adjustand telescope the steering columnposition. Return the lever to itsoriginal position to secure thewheel. The telescope function is adjustedby moving the wheel toward thedriver to telescope out and towardthe instrume...

Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers: • Place the VELCRO 威 hook onto the side of the aftermarkettransmitter opposite of thebutton. • Place the transmitter into storagecompartment, button down...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the rear windowcontrols slide the control to the left.Slide the control to the right torestore the window controls. EXTERIOR MIRRORS Power side view mirrors (if equipped) To adjust your mirrors: 1....

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h)or more without keeping your foot on the accelerator pedal. Speedcontrol does not work at speeds below 30 mph (48 km/h). Do not use the speed control in heavy traffic or on roads thatare winding, slippery...

STEERING WHEEL CONTROLS (IF EQUIPPED) Remote audio steering column controls (if equipped) The remote audio steering column controls may be used to select radioor CD mode. The following functions can be carried out using the remotecontrol. • Volume: Pull VOL + towards the steering wheel to increase t...

Bounce back: When an obstacle has been detected in the moon roof opening as themoon roof is closing, the moon roof will automatically open and stop at aprescribed position. Bounce back override: To override bounce back, press and hold the front portion of the control.For example: Bounce back can be ...

Wagon Pull out the roller cover and securethe retaining points. The cover canbe removed completely by pressinginward on both ends of the support. To reduce the risk of injury,the luggage cover must be properly attached to the mountingclips. Do not place any objects on the cargo area cover. They mayo...

Make sure that the liftgate door is closed to prevent exhaustfumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with theliftgate door open, keep the vents open so outside air comes into thevehicle LUGGAGE RACK (IF EQUIPPED) The ma...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency. Your keys are coded to your vehicle; using a non-coded key will notpermit your vehicle to start. If you lose your dealer supplied keys,replacement keys...

CHILDPROOF DOOR LOCKS (IF EQUIPPED) • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when the doorsare unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the...

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This devicemust accept any interference received, including interfe...

4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correct orientation of the battery. Press the batterydown to ensure that the battery is fully seated in the battery housingcavity. 5. Snap the two halves back together. Note: Replacement of the battery will no...

SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock 娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start...

Replacing coded keys can be very costly. Store an extra programmed keyaway from the vehicle in a safe place to help prevent anyinconveniences. Please visit an authorized dealer to purchase additionalspare or replacement keys. Programming spare keys You can program your own coded keys to your vehicle...

11. Your new, unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’sengine and the theft indicator light will illuminate for three seconds andthen go out. If the key was not successfully programmed, it will not start yourvehicle’s engine and the t...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Adjusting the front manual seat Sitting improperly out of position or with the seat back reclinedtoo far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury ordeath in a crash. Always sit upright against your seatback, with y...

Lift the control to adjust the angleof the seatback. Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Heated seats (if equipped) The heated seats switch is located on the center console. To operate t...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

• The warning light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and warning light are repaired. If any of these things happen, even intermittently, have the PersonalSafety System 娂 serv...

The front outboard and rear safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatsafety belts have two types of locking modes. Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing freeshoulder belt length adjustm...

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recom...

Three door models are equippedwith a safety belt parking feature forthe driver and front passenger. Thepurpose of the parking feature is toallow the driver or passenger toreach the safety belt. Fasten yoursafety belt as normal, and the beltwill slide to the front of the steelbar along the bottom of ...

Do not use extensions to change the fit of the shoulder beltacross the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All saf...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

If... Then... The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2 minuteshave elapsed since the ignitionswitch has been turned ON... The BeltMinder 娂 feature will not activate. The driver’s or front passenger’ssafety belt i...

One time disable If at any time the driver/front passenger quickly buckles then unbucklesthe safety belt for that seating position, the BeltMinder 娂 is disabled for the current ignition cycle. The BeltMinder 娂 feature will enable during the same ignition cycle if the occupant buckles and remains buc...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your authorized dealer. Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions tha...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

The SRS consists of: • driver and passenger airbag modules (which include the inflators andairbags). • side airbags (if equipped). Refer to Side airbag system later in this chapter. • one or more impact and safing sensors. • a readiness light and tone. • diagnostic module. • and the electrical wirin...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

some reason the safety belt is properly buckled). If the front passengerseat is empty, and the safety belt is not properly buckled, the frontpassenger seat side airbag will be turned off by the front passengersensing system. The airbag was designed to inflate between the doorpanel and occupant to fu...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Rear-facing child seats or infant carriers should never be ...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the stomach, and lets you adjust the shoulder belt to cross thechest and rest snugly near the center of the shoulder. The drawingsbelow compare the ideal fit...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position with LATCH andtether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

3. Locate the correct anchor for the selected seating position. • On Sedan’s the anchors arelocated on the rear back panel. • For 3–door/5–door and Wagon,the anchors are located on theback of the rear seat. 4. On a sedan, open the tetheranchor cover. 5. Clip the tether strap to theanchor as shown. I...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

urged to buy a reliable tire pressure gauge, as automatic service stationgauges may be inaccurate. Ford Motor Company recommends the use ofa digital or dial-type tire pressure gauge rather than a stick-type tirepressure gauge. Use the recommended cold inflation pressure for optimum tireperformance a...

recommended cold pressures. A hot tire at or below recommended coldinflation pressure could be significantly under-inflated. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile. Note: If you have to drive a distance to get air for ...

the tire and make necessary repairs. Also inspect the tire sidewalls forcracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case it needs to be repaired or replaced. For your safety,tires that are da...

U.S. DOT Tire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. Thenext two numbers or letters are the plant code designating where it wasmanufactured, the next two are the tire size code and the last fournumbers represent the we...

vehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel alignmentperiodically. Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by an authorized dealer.Fro...

Note: Your vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that isdifferent in brand, size or appearance from the road tires and wheels. Ifyou have a dissimilar spare tire/wheel it is intended for temporary useonly and...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. If you need to use chains, it i...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

calculation would be: 635 kg — (2 x 99 kg) — (12 x 45 kg) = 635 —198 — 540 = —103 kg. You will need to reduce the load weight by atleast 240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags,then the load calculation would be: 1400 – (2 x 220) – (9 x 100) = 1400 – 440 – 900 = 60 lb. Now youh...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourauthorized dealer or trailer rental agency for proper instructions andequipment for hooking up trailer lamps. Driving while you tow When tow...

RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as behind arecreational vehicle). These guidelines are designed to ensure that your transmission is notdamaged due to insufficient lubrication. All Front W...

STARTING Positions of the ignition 1. LOCK, locks the steering wheel,automatic transaxle gearshift leverand allows key removal. 2. OFF, shuts the engine and allelectrical accessories off withoutlocking the steering wheel. 3. ON, all electrical circuitsoperational. Warning lightsilluminated. Key posi...

If starting a vehicle with a manualtransaxle: 1. Make sure the parking brake isset. 2. Push the clutch pedal to the floor. • Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for mo...

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.5 cm) or a...

Four-wheel anti-lock brake system (ABS) (if equipped) Your vehicle may be equipped with an Anti-lock Braking System (ABS).This system helps you maintain steering control during emergency stopsby keeping the brakes from locking. Noise from the ABS pump motorand brake pedal pulsation may be observed d...

The BRAKE warning lamp willilluminate and will remainilluminated until the parking brakeis released. To release, press and hold the button (2), pull the handle up slightly,then push the handle down. Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (a...

The Traction Control 娂 switch is located on the center console, bythe gearshift lever. The TractionControl 娂 system will automatically turn on every time the ignition isturned off and on. If you should become stuck in snowor ice or on a very slippery road surface, try switching the TractionControl 娂...

• Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds. If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out byshifting between forward and reverse gears, stopping between shifts in asteady patte...

Recommended shift speeds Upshift according to the following chart: Recommended upshifts (for best fuel economy) when accelerating 5-speed manual transaxle Shift from: 1 - 2 14 mph (23 km/h) 2 - 3 24 mph (39 km/h) 3 - 4 32 mph (51 km/h) 4 - 5 44 mph (71 km/h) Reverse 1. Make sure that your vehicle is...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

U.S. Ford or Mercury vehicle customers who require roadside assistance,call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse...

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a few seconds...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 61 7.5A PATS modules, Instrument cluster 62 7.5A Radio (Start) 63 20A Power locks (GEM) Fuse 63 is located on the back of the fuse panel. See your authorizeddealer for service of this fuse. Power distribution box The po...

• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheel The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driv...

11. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nuttorque specification. 12. Put flat tire, jack and lug wrenchaway. Make sure the jack is fastenedso it does not rattle when you drive.Unblock t...

JUMP STARTING The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your vehicle. Automatictrans...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party mediation/arbitration program administered by the CanadianMotor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relat...

Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide Fre...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint...

• 2.0L and 2.3L I4 Engines PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and TarRem...

wax deposited on the wiper blade and windshield from automated carwash facilities. Be sure to replace wiper blades when they appearworn or do not function properly. • Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. Do not use sharp...

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaningthe seat-mounted side airbag (if equipped). Such products could contaminate the side airbag system and affect perform...

Motorcraft Car Wash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer ca...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleane...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L/2.3L I4 Engines 1. Power steering fluid reservoir 2. Engine oil filler cap 3. Brake/Clutch fluid reservoir 4. Power distribution box 5. Battery 6. Automatic transaxle fluid dipstick (if equipped) 7. Engine oil dipstick 8. Engine coolant reservoir...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has man...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Change your engine oil and filter according to the appropriate schedulelisted in scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material and ...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

• Add Motorcraft Premium Gold Engine Coolant(yellow-colored), VC-7–A (U.S., except CA, OR and NM),VC-7–B (CA, OR and NM), meeting Ford SpecificationWSS-M97B51–A1. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant fromyellow...

2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure ...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely cold climates (less than –34° F [–3...

How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperaturegauge will move to the red (hot)area. • The “Check Engine” indicatorlight will illuminate. If the engine reaches a presetover-temperature condition, the engine will automatically switch toalternating cylind...

FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If...

• The indicator may come on. For more information on the “Check Engine” or the “Service engine soon” indicator, refer to Warning lights and chimes in the Instrument Cluster chapter. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you,...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may n...

BRAKE/CLUTCH FLUID Brake and clutch systems are supplied from the same reservoir. The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. ...

If necessary, add fluid in 1/2 pint (250 mL) increments through the fillertube until the level is correct. If an overfill occurs, excess fluidshould be removed by an authorizeddealer. An overfill condition oftransmission fluid may causeshift and/or engagementconcerns and/or possibledamage. Do not us...

Component 2.0L I4 engine 2.3L I4 engine PCV valve 2 Spark plugs 3 1 Non Serviceable Part. The air filter is designed to last the life of the vehicle. See authorized dealer or qualified technician for replacement.The Technician can check the diagnostics system for the possibility of anexcessively dir...

• Wagon IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic SafetyAdministration Regulations requirethat a Safety ComplianceCertification Label be affixed to avehicle and prescribe where theSafety Compliance CertificationLabel may be located. The SafetyCompliance Certification ...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Air cleaner filter .......................203 Airbag supplemental restraintsystem ..............................82–83, 91 and child safety seats ..............84description ..........................83, 91disposal ......................................93driver airbag ........................84, 92...