Ford 2006 Explorer v.1- User Manual

Fuel pump shut-off switch: In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g.collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emerg...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type,failur...

A driver’s first responsibility is the safe operation of the vehicle.The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe tooperate Mobile Communications Equipment. Middle East/North Africa vehicle specific information F...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

bulb works. If any light remains on after starting the vehicle, refer to therespective system warning light for additional information. Note: Some Warning Lights will display in the Message Center as words and function the same as the warning light. Note: Depending on which options your vehicle has,...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON positionwhen the engine is not running, or in a position between ON and START,or by applying the parking brake when the ignition is turned to the ONp...

Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Serviceengine soon warning light to come on. Refer to Fuel filler cap in the Maintenance and Specifications chapter. • Standard instrument cluster • Optional instrument clu...

Four wheel drive high (ifequipped): Illuminates when four-wheel drive is engaged. If thelight fails to illuminate when the ignition is turned ON, or remains on,have the system serviced immediately by your authorized dealer. Door ajar: Illuminates when the ignition is in the ON position andany door, ...

Parking brake ON warning chime: Sounds when the parking brake is set, the engine is running and the vehicle is driven more than 3 mph(5 km). GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature,...

AUDIO SYSTEMS AM/FM Single CD/MP3 sound system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped)may be used for up to ten minutes after the ignition is turned off or untileither front door is opened...

Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2. PressMENU to access. Use / to set. When the six strongest stations are filled, the station stored in preset 1will begin playing. If there are less than six strong s...

AM/FM Single CD/MP3/Cassette sound system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped)may be used for up to ten minutes after the ignition is turned off or untileither front door is opened. 1. ...

5. AUX: Press to toggle between FES/DVD and AUX modes. If noauxiliary sources are available, NOAUX AUDIO will be displayed. To return to radio mode, press AM/FM. 6. Tape eject: Press to eject a tape. 7. Play/Pause: This control is operational in CD, tape and DVDmode (if equipped). When a CD orDVD is...

Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12cm) audio compact discs only. Due to technical incompatibility,certain recordable and re-recordable compact discs may n...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. MAX A/C: Uses recirculated a...

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED) 1. A/C control: Manually turns A/C on or off. 2. Recirculation control: Cools the vehicle more quickly byrecirculating the cabin air instead ofusing outside air and helps prevent unpleasant outside odors or fumesfrom entering the vehicle....

16. EXT: Displays the outside air temperature. It will remaindisplayed until the EXT control ispressed again. The external temperature will be most accurate when thevehicle has been moving for a period of time. 17. Temperature conversion: Press to toggle between Fahrenheitand Celsius temperature on ...

REAR WINDOW DEFROSTER The rear defroster control is locatedon the instrument panel. Press the rear defroster control toclear the rear window of thin iceand fog. • A small LED will illuminate whenthe rear defroster is activated. The ignition must be in the 3 (ON) position to operate the rear windowde...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp system(if equipped) The autolamp system sets theheadlamps to turn on and offautomatically. The autolamp control,located on the headlamp contro...

Push the headlamp control towards the instrument panel to deactivatethe foglamps. Daytime running lamps (DRL) (if equipped) To activate DRL: • the ignition must be in the ON position and • the headlamp control is in the or position • the transmission is not in park. Always remember to turn on your h...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel when exteriorlights are on. • Rotate the thumbwheel from leftto right to brighten theinstrument panel. • Rotate the thumbwheel from rightto left to dim the instrumentpanel. • Rotate to fully to the right (past detent) to turn o...

3. Turn on the low beam headlamps.The brightest part of the lightshould be below the horizontal line(4). If it is above the line theheadlamp will need to be adjusted. 4. Open the hood. 5. Locate the vertical adjuster foreach headlamp. Adjust the aim byturning the adjuster control eitherclockwise (to...

INTERIOR LAMPS Dome/reading lamps The dome lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on. • any of the remote entry controlsare pressed and the ignition isOFF. The reading portion, the two outer lights, can only be toggled o...

Replacing headlamp bulbs Do not touch the glass of a halogen bulb. 1. Turn off the headlamps and openthe hood. 2. Remove three screws from theheadlamp assembly and pullheadlamp forward. 3. Disconnect the electricalconnector. 4. Remove the old bulb by turningcounterclockwise and pull it out. Handle a...

Replacing front parking lamp/turn signal/sidemarker bulbs 1. Turn off the headlamps and openthe hood. 2. Remove three screws from theheadlamp assembly and pullheadlamp forward. 3. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly. 4. Pull the bulb straight out of thesocket. ...

Replacing high-mount brakelamp bulb 1. Remove the two screws and lampassembly away from the vehicle. 2. Remove the bulb holder from thelamp assembly by depressing thesnaps. 3. Pull the bulb straight out of thesocket and push in the new bulb. Reverse steps to reinstall bulb(s). Lights 51

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

TILT STEERING COLUMN Pull the lever down and release, tounlock the steering column tilt lock.With the lever in the down position,tilt the steering column and wheelto its desired orientation. Do notpush or pull the lever while tiltingthe wheel. Lift the lever back to its originalposition to lock the ...

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment Press the latch to open the storagecompartment. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a vari...

• Place the provided heightadaptors onto the back of thedoor as needed. • Close the door. • Press the depression in the doorto activate the transmitter. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will d...

POWER WINDOWS Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the proximity of the ...

Accessory delay With accessory delay, the window switches, audio system and moon roof(if equipped) may be used for up to ten minutes after the ignition switchis turned to the OFF position or until either front door is opened. AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may b...

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h)or more without keeping your foot on the accelerator pedal. Speedcontrol does not work at speeds below 30 mph (48 km/h). Do not use the speed control in heavy traffic or on roads thatare winding, slippery...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previouslyset speed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased...

Press FAN + or - to adjust fanspeed. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up(from the closed position) to ventilate the vehicle. Do not let children play with the moon roof or leave childrenunattended in the vehicle. They may seriously hurt thems...

Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink t equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, theprogrammed Homelink t buttons be erased for security purposes, refer to Programming in thi...

4. The indicator light will flash slowly and then rapidly. Release bothbuttons when the indicator light flashes rapidly. (The rapid flashing lightindicates acceptance of the hand-held transmitters’ radio frequencysignals.) 5. Press and hold the just-trained HomeLink t button and observe the indicato...

Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink t to accept the signal from the hand-held transmitter. After completing Steps 1 and 2outlined in the “Programming” section, replace Step 3 w...

Erasing HomeLink T buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink t buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink t is now in the train...

Selectable features Press and release the TRIP/RESETcontrol switch to scroll and resetthe following functions. Select orreset the function by holding theTRIP/RESET button for more that 2seconds. Info menu This menu displays the following control displays: • Odometer/Trip Odometer • Distance to Empty...

Average fuel economy (AFE) Select this function to display youraverage fuel economy in miles/gallonor liters/km. If you calculate your average fueleconomy by dividing miles traveledby gallons of fuel used (liters of fuelused by 100 kilometers traveled), your figure may be different thandisplayed for...

System check Press and hold the TRIP/RESETcontrol switch to select SYSTEMCHECK when “RESET FOR SYSCHECK” is displayed in the messagecenter. Selecting this function fromthe SETUP MENU causes themessage center to cycle through each of the systems being monitored.For each of the monitored systems, the ...

Units (English/Metric) 1. Select this function from theSETUP MENU for the current unitsto be displayed. 2. Press and hold the TRIP/RESETcontrol switch to change fromEnglish to Metric. 3. Press the TRIP/RESET control switch for the next SETUP MENU itemor wait for more than 4 seconds return to the INF...

Oil Life Start Value 1. Select this function from theSETUP MENU for the currentdisplay mode. 2. Press and hold the TRIP/RESETcontrol switch to reset oil change. 3. Press the TRIP/RESET controlswitch for the next SETUP MENU item or wait for more than 4 secondsto return to the INFO MENU. Note: Oil Lif...

Compass zone adjustment 1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap. 2. Turn ignition to the ON position. 3. Locate the reset button on top ofthe compass sensor mounted behindthe mirror. 4. Press and hold the reset buttonon the compass module fo...

Compass calibration adjustment Perform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, turn off all electricalaccessories (heater/air conditioning, wipers, etc.) and make sure allvehicle doors are shut. 1. Start the vehicle. 2. Locate th...

PARK BRAKE ENGAGED. Displayed when the manual park brake is set, the engine is running and the vehicle is driven more than 3 mph(5 km). If the warning stays on after the park brake is released, contactyour authorized dealer as soon as possible. CHECK BRAKE SYSTEM. Displayed when the braking system i...

WASHER FLUID LEVEL LOW. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter. OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 0%. An oil change is required...

Your display can show up to 6 reconfigurable telltales at one time. Whatever is displayed in the top left corner has the highest priority. Selectable features Reset Press the RESET control to selectand reset functions shown in theINFO menu, SETUP menu, textwarnings and reconfigurable telltalewarning...

Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from theINFO menu estimates approximatelyhow far you can drive with the fuelremaining in your tank undernormal driving conditions.Remember to turn the ignition OFFwhen refueling to allow ...

2. Record the highway fuel economy for future reference. It is important to press the RESET control (press and hold RESET for 2seconds in order to reset the function) after setting the speed control toget accurate highway fuel economy readings. Instantaneous fuel economy Select this function from th...

Reverse Sensing System (Park Aid) This feature sounds a warning tone to warn the driver of obstacles nearthe rear bumper, and functions only when R (Reverse) gear is selected. 1. To disable/enable the reversesensing system feature with thevehicle in P (Park), select thisfunction from the SETUP MENU ...

Compass calibration adjustment. Perform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, turn off all electricalaccessories (heater/air conditioning, wipers, etc.) and make sure allvehicle doors are shut. 1. From the SETUP menu, press the...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for 4seconds. The message center will display the last...

Warning display Status Check park aid Warning returns only after the ignitionkey is turned from OFF to ON. Low tire pressure Tire monitor fault Tire sensor fault Brake fluid level low Check brake lamp Check headlamp Check highbeam Check turn lamp Washer fluid level low Oil change required Engine oil...

Do not place any objects on the cargo area cover. They mayobstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. Cargo management system The cargo management system consists of storage compartments locatedin the floor of the rear cargo area. 7 passenger st...

REAR LIFTGATE The liftgate area is only intended for cargo, not passengers. You can openand close the liftgate from outside the vehicle. It cannot be opened frominside the cargo area. • To open the liftgate window,press the control on the remoteentry transmitter or, with theliftgate unlocked, push t...

LUGGAGE RACK Your vehicle is equipped with a roofrack. The maximum recommendedload is 100 lbs (45 kg), evenlydistributed. Use the tie down loopson the thumbwheels (if equipped)to secure the load. To adjust cross-bar position (ifequipped): 1. Loosen the thumbwheel at bothends of the cross-bar (bothcr...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

CHILDPROOF DOOR LOCKS • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when the doorsare unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one ...

The remote entry system allows youto lock or unlock all vehicle doorsand liftgate, open the liftgatewindow without a key and activatethe panic alarm. The remote entry lock/unlock feature operates in any ignition position.The liftgate glass feature operates as long as the vehicle’s speed is lessthan ...

Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and one step door unlocking by pressing andholding both the and buttons simultaneously on the remote entry transmitter for approximately 4 seconds. The par...

Activating the memory seat feature To activate this feature: 1. Position the seat and adjustable pedals to the position desired. 2. Press the SET control on thelower-center portion of theinstrument panel. 3. Within 5 five seconds, press onecontrol on the remote transmitterand then press the 1 or 2 c...

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correc...

The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 10 minutes after theignition has been turned to the 1 (OFF/LOCK) position. KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless ...

Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personalcode. • If you program a code to a position that already contains a set code,the previously-set code will be erased. Eras...

Autolock The autolock feature will lock all the doors, liftgate and liftgate windowwhen: • all doors are closed, • the ignition is in the 3 (ON) position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). The autolock feature re...

4. Press the power door unlock control three times. 5. Turn the ignition back to the 3 (ON) position. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn willchirp once if autolock was deactivated or twice (one short and one longchirp) if autolock was activated. 7...

Deactivating/activating autounlock Your vehicle comes with the autounlock feature activated. There are fourmethods to enable/disable this feature: • Through your authorized dealer, or • Performing the power door lock control procedure, or • Performing the keyless entry key pad (if equipped) procedur...

6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has beendisabled or a chirp followed by a honk to indicate the system has beenenabled. Message center procedure For information on activating/deactivating the autounlock feature usingthe vehicle’s message center (if eq...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 2(ACCESSORY) position. The theft indicator will flash everytwo seconds when the vehicle isarmed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. • The theft in...

Please read and understand theentire procedure before you begin. 1. Insert the first previouslyprogrammed coded key into the ignition. 2. Turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON)position. Keep the ignition in the 3 (ON) position for at least threeseconds, but no more than 10 se...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Push control to lower head restraint. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Lift handle to move seat forward orbackward. Pull l...

Press the control to recline theseatback forward or rearward. Memory seats and adjustable pedals (if equipped) This system allows automaticpositioning of the driver seat andadjustable pedals to twoprogrammable positions. The memory seat control is locatedon the lower-center portion of theinstrument ...

Using the manual lumbar support (if equipped) For more lumbar support, turn thelumbar support control toward thefront of vehicle. For less lumbar support, turn thelumbar support control toward therear of vehicle. Heated seats (if equipped) The heated seat control is located in the lower center of th...

1. Lower the head restraints bypulling on the strap. 2. Locate handle on the side of theseat cushion by the door. 3. Pull up on the handle and pushthe seatback forward toward thefront of the vehicle. To return the seat to the upright position: 1. Lift the seatback toward the rearof the vehicle. 2. R...

3. Lift up on the head restraint untilit locks into its original position. Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has ...

Returning to the upright position from full lowered load floorposition The seatback cannot be returned to the upright position until the seat isreturned from the kneel down position. To return the seat to the uprightposition: 1. Push the seat rearward until thelatch is engaged. 2. Return the seatbac...

To return the seat to a seating position: 1. Push the seat down and latch tothe floor with a moderate amount ofeffort and speed. 2. Make sure the seat is latched tothe floor. 3. Bring the seat back to an uprightposition. The seatback should lockinto position. Note : If the seat back will not return ...

3rd row folding seat (if equipped) Before folding the third row seats,fold the head restraints down bypulling on the strap located underthe restraint. Pull up on the handle locatedbehind the seatback while pushingthe seatback forward and down intothe seat cushion. Before returning the seatback to it...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

The fact that the pretensioners or airbags did not activate for both frontseat occupants in a collision does not mean that something is wrong withthe system. Rather, it means the Personal Safety System y determined the accident conditions (crash severity, belt usage, etc.) were notappropriate to act...

Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all theway back. Always transport children 12 years old and under in the backseat and always properly ...

Determining if the Personal Safety System Y is operational The Personal Safety System y uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Referto the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of th...

It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people toride in any area of your vehicle that is not equipped with seats andsafety belts. Be sure everyone i...

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest tothe direction the tongue is coming from) until you hear a snap and feel itlatch. Make sure the tongue is securely fastened in the buckle. • Front and rear seats 2. To unfasten, push the release ...

Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. This mode should be used any time a ch...

• Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Unbuckle the combination lap and shoulder belt and allow it to retractcompletely to disengage the automati...

To adjust the comfort guide: 1. Slip the shoulder belt into thebelt guide. 2. Slide the guide up or down alongthe webbing so that the belt iscentered on the occupant’’sshoulder. Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch(20 cm) safety belt e...

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’s or frontpassenger’s safety belt is notbuckled before the igniti...

To reduce the risk of injury, do not deactivate/activate theBeltMinder y feature while driving the vehicle. 1. Turn the ignition switch to the RUN (or ON) position. (DO NOTSTART THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1minute) • Step 3 must be completed with...

assemblies not in use during a collision should also be inspected andreplaced if either damage or improper operation is noted. Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severe personal injuries in the event of a collision. For prop...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

To reduce the risk of possible serious injury:Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).Check the “...

Any alteration/modification to the front passenger seat mayaffect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Airbag readiness secti...

Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided. How does the side airbag system work? The design ...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, i...

Do not attempt to service, repair, or modify the Safety Canopy y system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy y . See your authorized dealer. All occupants of the vehicle including the driver should alwayswear their safety belts even when an...

If the Safety Canopy y system has deployed, the Safety Canopy y will not function again. The Safety Canopy y system (including the A, B and C pillar trim) must be inspectedand serviced by an authorized dealer. If the Safety Canopy y is not replaced, the unrepaired area will increase the risk of inju...

require that children use approved booster seats until they are eightyears old. Check your local and state or provincial laws for specificrequirements regarding the safety of children in your vehicle. Whenpossible, always place children under age 12 in the rear seat of yourvehicle. Accident statisti...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulderbelt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk ...

Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use the lap/shoulderbelt. If a seating position has alow seat back and no headrestraint, a backless booster seatmay place...

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the stomach, and lets you adjust the shoulder belt to cross thechest and rest snugly near the center of the shoulder. The drawingsbelow compare the ideal fit...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position with LATCH andtether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information ontransfer case operation and shiftingprocedures can be found in the Driving chapter. Information on transfer case maintenance can be foun...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls forcracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

on the tire sidewall). Additionally, if your vehicle was originally equippedwith run-flat tires, replacing them with tires that are not identical tothose originally fitted may cause malfunction of the TPMS, and is notrecommended. Run-flat tires should not be used to replace regular tires.Always chec...

vehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel alignmentperiodically. Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by an authorized dealer.Fro...

The Tire Pressure Monitoring System is NOT a substitute formanually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge, see Inflating your tires in this chapter. Failure to properly maintain your tire pressure could increase the risk of tir...

In short, once the light has turned ON, at least one tire may be underinflated. When your temporary spare tire is installed (if equipped) When one of your road tires needs to be replaced with the temporaryspare (T-type spare/Mini spare or Dissimilar spare), the TPMS systemwill continue to identify a...

Low Tire PressureWarning Light Possible cause Customer Action Required Solid Warning Light Tire(s)under-inflated 1. Check your tire pressure toensure they are properlyinflated; refer to Inflating your tires in this chapter. Ford Motor Company recommendsthe use of a digital or dial-typetire pressure ...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight (flashes for 20to 30 seconds eitherat start-up or whiledriving) Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionalit...

How temperature affects your tire pressure The Tire Pressure Monitoring System (TPMS) monitors tire pressure ineach pneumatic tire. The pressure in each tire is dependent upon severalfactors, one of them being the contained air temperature (temperature ofthe air inside the tire). As the contained ai...

USING SNOW TIRES AND TRACTION DEVICES Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all-weather treads to provide traction inrain and snow. However, in some climates, using snow tires or tractiondevices may be necessary. For...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. Tires, Wheels and Loading 194

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

4x2 GCWR (Gross Combined Weight Rating)/Trailer Weight Engine Rear axle ratio Maximum GCWR-lb. (kg) Trailer weightrange-lb. (kg)(0-Maximum) 4.0L SOHC ClassII towing 3.55 7700 (3493) 0–3110 (0–1410) 4.6L* Class IItowing 3.55 7700 (3493) 0–3020 (0–1369) 4.0L SOHC ClassIII/IV towing 3.73 10000 (4536) 0...

4WD GCWR (Gross Combined Weight Rating)/Trailer Weight Engine Rear axle ratio Maximum GCWR-lb. (kg) Trailer weightrange-lb. (kg)(0-Maximum) 4.0L SOHC ClassII towing 3.55 8000 (36 29) 0–3230 (0–1465) 4.6L* Class IItowing 3.55 8000 (3629) 0–3140 (0–1424) 4.0L SOHC ClassIII/IV towing 3.73 10000 (4536) ...

Never connect any trailer lighting to the vehicle’s taillampcircuits, because it may damage the electrical system resulting in fire. Contact your authorized dealer for assistance in proper trailer towwiring installation. Additional electrical equipment may be required. Driving while you tow When tow...

• The trailer tongue weight should be 10–15% of the loaded trailerweight. • If you will be towing a trailer frequently in hot weather, hillyconditions, at GCW, or any combination of these factors, considerrefilling your rear axle with synthetic gear lube if not already soequipped. Refer to the Maint...

STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval. 2. ACC, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. This position also unlocksthe steering wheel. 3...

Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel until thekey turns freely. This condition mayoccur when: • the front wheels are turned • a front wheel is against the curb 2. Turn the key to 4 (START...

To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater) adapters. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-outand should be i...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

If the vehicle is stuck in snow or mud or when driving in deep sand,switching off the AdvanceTrac with RSC system may be beneficial so thewheels are allowed to spin. If your vehicle seems to lose engine powerwhile driving in deep sand or very deep snow, switching off theAdvanceTrac with RSC stabilit...

AdvanceTrac t with RSC Features Buttonfunctions “Sliding car” icon RSC ESC Engine Traction Control Brake Traction Control Default atstart-up Illuminated during bulb check Enabled Enabled Enabled Enabled Buttonpressedmomentarily Illuminated solid Disabled below 25 mph (40 km/h) Disabled below 25 mph ...

Loaded vehicles, with a higher center of gravity, may handledifferently than unloaded vehicles. Extra precautions such as slower speeds and increased stopping distance should be taken whendriving a heavily loaded vehicle. AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equippe...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your authorized dealer. Driving with a 5–speed automatic transmission This vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive Shift Strategy offer...

1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Overdrive) or Drive. • Depress the accelerator to the floor. • Allow...

• Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Drive) only. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. If your...

FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this typeof vehicle, see Preparing to drive your vehicle in this chapter. Four–wheel drive (4WD) supplies power to all four wheels. 4WD shouldnot be operated on dry pavement; driveline damage may occ...

Shifting between 4X4 AUTO (4WD Auto) and 4X4 HIGH (4WD High) • Select 4X4 AUTO (4WD Auto) or 4X4 HIGH (4WD High) at anyforward speed. Note: Do not perform this operation if the rear wheels are slipping. Shifting to/from 4X4 LOW (4WD Low) 1. Bring the vehicle to a complete stop 2. Depress the brake 3...

Basic operating principles • Do not use 4WD High or 4WD Low on dry, hard surfaced roads. Doingso will produce excessive noise, increase tire wear and may damagedrive components. 4WD modes are only intended for consistentlyslippery or loose surfaces. • Drive slower in strong crosswinds which can affe...

Do not rock the vehicle for more than a few minutes or damageto the transmission and tires may occur or the engine mayoverheat. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable emergency situation where a ...

leave the vehicle unattended with the transfer case in the N (Neutral)position. Always set the parking brake fully and turn off the ignitionwhen leaving the vehicle. Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remov...

how much air is released from your tires and/or how long you drive thevehicle under these conditions. Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required from another vehicle. Remember, you may be able t...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slip...

Driving on snow and ice 4WD vehicles have advantages over 2WD vehicles in snow and ice butcan skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn thesteering wheel in the direction of the slide until you regain control. Avoid sudden applications of power ...

Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand adversely affect driver and passenger safety. Frequent inspection ofvehicle chassis components is recommended if the vehicle is subjected toheavy off-...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the flasher...

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switc...

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wiredamage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses 2A Grey Grey...

Passenger compartment fuse panel The fuse panel is located below theinstrument panel on the driver’sside. To remove a fuse use the fuse puller tool provided on the fuse panel box. The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 20A M...

Power distribution box The power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protect yourvehicle’s main electrical systemsfrom overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electrical...

Have a flat serviced by an authorized dealer in order to prevent damageto the TPMS sensor, refer to Changing tires with TPMS in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. The use of tire sealants may damage your tires. The use of tiresealants ...

• Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to im...

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel andseek service as ...

If your vehicle is equipped with TPMS, have a flat tire serviced by anauthorized dealer in order to prevent damage to the TPMS sensor, referto Changing tires with TPMS in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. The spare tire and tools for ...

Rotate the wrench socket out fromthe handle. Removing the spare tire Do not use an impact wrench on the winch drive nut. This willdamage the spare tire winch. 1. Open the cover from the carpeting on cargo floor to expose the winchdrive nut. 2. Insert the lug wrench on thewinch drive nut. The wrench ...

3. Turn the wrenchcounterclockwise until the tire islowered to the ground and the cablehas slack. When turning the wrench,make sure that it does not scuff thekick plate. 4. Slide the tire rearward, lift oneside and remove the retainer fromthe spare tire. Changing the spare tire To prevent the vehicl...

To lessen the risk ofpersonal injury, do not put any part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle is on the jack. The jack isonly meant for changing the tire. • Never use the front or reardifferential as a jacking point. 5. Remove the lug nuts wit...

the tire is raised to the maximum tightness. Tighten to the best of yourability, to the point where the ratchet/slip occurs, if possible. The sparetire carrier will not allow you to overtighten. If the spare tire carrierratchets or slips with little effort, take the vehicle to your authorizeddealer ...

When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc thatcontacts the wheel. Ensure that any fasteners that attach the rotor tothe hub are secured so they do not interf...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect the po...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to the ground studlocated towards the front of the vehicle (forward of the battery) on theradiator support. Keep the negative (-) cable away from the battery...

Do not connect the end of the second cable to the negative (-)terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts. Jump st...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicleneeds service, or if you need more help than the authorized dealer couldprovide, afte...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party mediation/arbitration program administered by the CanadianMotor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relat...

Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide Fre...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washing orlaundry liquid. These products can dis...

PAINT CHIPS Your authorized dealer has touch-up paint and sprays to match yourvehicle’s color. Take your color code (printed on a sticker in the driver’sdoor jamb) to your authorized dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). • For plastic...

Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination of the airbag system. • Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoi...

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over theleather. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleaner (ZC-11–A). Dry the area with a soft cloth. • To help maintain its resiliency and color, use the Motorcraft DeluxeLe...

SERVICE RECOMMENDATIONS • Use the scheduled maintenance information to track routine service. • Use only recommended fuels, lubricants, fluids and service partsconforming to specifications. • Your authorized dealer can provide parts and service. PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work ...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance and Specifications 277

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Engine oil filler cap 2. Engine oil dipstick (out of view) 3. Brake fluid reservoir 4. Power distribution box 5. Battery 6. Power steering fluid reservoir 7. Radiator cap 8. Engine coolant reservoir 9. Air filter assembly 10. Wa...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2.Do not use any special washer fluid such as windshield water repellenttype fluid or bug wash. They...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

5. Locate and carefully remove the engine oil level indicator (dipstick). • 4.0L V6 engine • 4.6L V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the lower and upper holes, the oil level is acceptable, DO NOT ADD OIL. • If the oil...

• 4.0L V6 engine • 4.6L V8 engine • Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to scheduled maintenance information for the servi...

When lifting a plastic-cased battery, excessive pressure on the endwalls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the batterywith a battery carrier or with your hands on opposite corners. Keep batteries out of reach of...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium GoldEngine Coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner....

Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cooling systemand engine protection. What you should know about fail-safe cooling (4.6L V8 engine only) If the engine coolant supply is depleted, this feature allows the veh...

3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Restart the engine and take your vehicle to an authorized dealer. Driving the vehicle without repairin...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

should turn off after three driving cycles with the fuel filler cap properlyinstalled. A driving cycle consists of a cold engine start-up followed bymixed city/highway driving. If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer w...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” thatare sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes kno...

• The indicator may come on. For more information on the “Check Engine” or the “Service engine soon” indicator, refer to Warning lights and chimes in the Instrument Cluster chapter. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you,...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

• Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessaryshifting between third and fourth gear occurs. Unnecessary shifting ofthis type could resu...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may n...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “MAX” linethat do not trigger the brake systemwarning lamp are within the normaloperating range, there is no need toadd fluid. If the fluid levels areoutside of ...

TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to Lubricant specifications...

an automatic transmission application requiring MERCON t SP may cause transmission damage. Use of a transmission fluid other than therecommended fluid may cause transmission damage. Refer to your scheduled maintenance information to determine the correct service interval. 2 Indicates only approximat...

Item Ford PartName orequivalent Ford PartNumber FordSpecification Driveshaft, slipspline, universaljoints Premium LongLife Grease XG-1-C ESA-M1C75-B Engine coolant MotorcraftPremium GoldEngine Coolant(yellow-colored) VC-7-A (U.S.,except CA, ORand NM),VC-7-B (CA, ORand NM) WSS-M97B51-A1 Engine oil(4....

1. World manufacturer identifier 2. Brake type and gross vehicleweight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find atransmission/transaxle code on th...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Accessory delay ..........................58 AdvanceTrac ..............................212 Air cleaner filter ...............306–307 Air conditioning ..........................37 Airbag supplementalrestraint system ........141, 150, 152 and child safety seats ............143description ..............

Tires ...........................172–174, 246 alignment ................................184care ..........................................181changing ..........................246, 252checking the pressure ............177inspecting and inflating .........175label .......................................