Page 2 - Table of Contents
Tires, Wheels and Loading 110 Tire Information 111 Changing tires 115 Lug Nut Torque 120 Vehicle loading 130 Trailer towing 137 Recreational towing 137 Driving 138 Starting 138 Brakes 141 Traction control/AdvanceTrac 143 Transmission operation 144 Roadside Emergencies 151 Getting roadside assistance...
Page 3 - Copyright © 2004 Ford Motor Company
Accessories 219 Index 221 All rights reserved. Reproduction by any means, electronic or mechanicalincluding photocopying, recording or by any information storage and retrievalsystem or translation in whole or part is not permitted without writtenauthorization from Ford Motor Company. Ford may change...
Page 4 - Owner’s Guide; Introduction
CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or otherreproductive harm. In addition, certain fluids contained in vehicles andcertain pro...
Page 5 - Engine oil
SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...
Page 6 - Warranty Guide; Service Data Recording; Event Data Recording
SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...
Page 7 - Special instructions; Please read the section; NEVER; be placed in front of an active passenger air bag.
Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...
Page 8 - Vehicle Symbol Glossary
These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...
Page 10 - WARNING LIGHTS AND CHIMES; The; CHECK; Instrument Cluster
WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...
Page 11 - Brake system warning light:; BRAKE
Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON positionwhen the engine is not running, or in a position between ON and START,or by applying the parking brake when the ignition is turned to the ONp...
Page 14 - GAUGES; Indicates the; If it enters the red section,
GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...
Page 16 - Entertainment Systems
AUDIOPHILE SATELLITE READY AM/FM STEREO IN-DASH SIX CDRADIO 1. Seek: Press and release SEEK / for previous/next strong station or track. 2. Rewind: In CD mode, press until desired selection is reached. Fast forward: In CD mode, press until desired selection is reached. TEXT: TEXT is only available w...
Page 18 - Traffic information is not available in most
Traffic: Allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it isbroadcasting RDS data). Traffic information is not available in most U.S. markets. FIND Program type: Allows you to search RDS-equipped stations for a cert...
Page 19 - Speed sensitive volume:
13. Power/volume: Press to turn ON/OFF; turn to increase ordecrease volume levels. Speed sensitive volume: Radio volume changes automatically andslightly with vehicle speed tocompensate for road and wind noise. Recommended level is 1–3. Level 0turns the feature off and level 7 is the maximum setting...
Page 20 - There are three factors that can effect radio reception:
For information regarding SIRIUS Satellite Radio, please call toll-free888-539-SIRIUS (888-539-7474) or visit the SIRIUS website atwww.siriusradio.com RADIO FREQUENCIES AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCo...
Page 21 - AUDIO SYSTEM WARRANTY AND SERVICE; Refer to the
CD units are designed to play commercially pressed 12 cm (4.75in) audio compact discs only. Due to technical incompatibility,certain recordable and re-recordable compact discs may notfunction correctly when used in Ford CD players. Irregularshaped CDs, CDs with a scratch protection film attached, an...
Page 22 - Rear; Climate Controls
DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL(DEATC) SYSTEM 1. A/C control: Press to turn on and manually control the airconditioning. Press again todisengage. Press AUTO for the system to automatically control thetemperature. 2. Recirculation control: Press to engage/disengage. Used to manuallyenab...
Page 24 - Press to display; Temperature conversion:
16. EXT control: Press to display the outside air temperature. Pressagain to return to interiortemperature. Exterior readings are most accurate when the vehicle ismoving. 17. Temperature conversion: Press to toggle between Fahrenheitand Celsius temperature on theDEATC display only. The set point tem...
Page 25 - To aid in side window defogging/demisting in cold weather:; REAR WINDOW DEFROSTER
• Do not place items over theclimate temperature sensor grid.This may cause improperoperation of the system. To aid in side window defogging/demisting in cold weather: 1. Select . 2. Ensure that recirculation is disengaged.3. Set the temperature control to full heat.4. Set the fan to the highest spe...
Page 26 - CABIN AIR FILTER; Improves the interior compartment cleanliness
CABIN AIR FILTER Your vehicle is equipped with a cabin air filter. The particulate airfiltration system is designed to reduce the concentration of airborneparticles such as dust, spores and pollen in the air being supplied to theinterior of the vehicle. The particulate filtration system gives thefol...
Page 27 - AUTO; Lights
MASTER LIGHTING SWITCH Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns on the headlamps, parking lamps, instrument panellamps, license plate lamps and taillamps. Autolamp control The autolamp system provides lightsensitive automatic o...
Page 28 - Rotate up to brighten.
Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provideadequate lighting during these conditions. Failure to activate yourheadlamps under these conditions may result in a coll...
Page 29 - HEADLAMP VERTICAL AIM ADJUSTMENT; Close the hood and turn off the lamps.
The dome light will only go on when the dome light switch is in thedelay or ON position. HEADLAMP VERTICAL AIM ADJUSTMENT 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp togrou...
Page 30 - Check the operation of all of the bulbs periodically.
TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. INTERIOR LAMPS Reading and dome lamps The reading lamps are located in theheader trim panel. Press the controlnext to the reading lamp to activateit. The reading lamp assembly alsocontains an...
Page 32 - Replacing headlamp bulbs; To remove the headlamp bulb:
Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is inOFF position, then open the hood. 2. Pry up the two retainer pins torelease the headlamp assembly fromthe vehicle. 3. Remove the nut from the back ofthe headlamp and pull headlampforward. 4. Disconnect the electr...
Page 38 - CHANGING THE WIPER BLADES; Windows and; Driver Controls
MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...
Page 39 - POWER TILT/TELESCOPE STEERING COLUMN; The tilt function is adjusted by moving the control up or down.
POWER TILT/TELESCOPE STEERING COLUMN The steering column can beadjusted manually by moving thefour-way rocker adjustment controllocated below the turn signal/wipercontrol stalk. Hold the control toadjust. The telescope function is adjustedby moving the control toward thedriver to telescope out and t...
Page 40 - POWER WINDOWS; the proximity of the window openings.; One touch down
Cigarette/Cigar lighter (if equipped) Do not plug optional electrical accessories into the cigarette lightersocket.Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromits heating position when it is ready to ...
Page 41 - Short drop glass; Though your windows will have been calibrated before; If a window loses its calibration, your short drop; VISOR MIRROR; To adjust your mirrors:
Short drop glass In order to improve door efforts and sealing, your vehicle is equippedwith short drop glass. This feature lowers the glass when either door isopened. The glass returns to its closed position when the door is closed.If the optional removable top is not installed on your vehicle, this...
Page 43 - Setting speed control; light on the
Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...
Page 45 - STEERING WHEEL CONTROLS; These controls allow you to operate some audio control features.; Audio control features
• Depress the brake pedal orCANCEL until the desired vehiclespeed is reached, press the SET+ control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or pressCANCEL. This will not erase yourvehicle’s previously set speed. • Press the speed contro...
Page 47 - Programming
When programming your HomeLink 威 Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink 威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as requ...
Page 49 - Gate Operator & Canadian Programming; “Programming”; every two
Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink 威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2outlined in the “Programming” section, replace Step 3 w...
Page 50 - Do NOT
Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the train...
Page 51 - Push the handle back into the lock position.
The convertible top will operate with the key in the RUN position,RUN/ACC position or in the accessory delay mode. It is recommendedthat the vehicle’s engine is running when lowering the top to preventdraining the battery. 2. Check the convertible top stowage compartment behind the seat to besure it...
Page 52 - Raising the convertible top; To raise the convertible top:
2. Tuck the boot under the upperback panel at the rear and thequarter panel along the sides. 3. To remove unfasten the snaps. 4. Pull forward and lift off. Raising the convertible top To raise the convertible top: 1. Bring the vehicle to a complete stop. Put the vehicle in the P (Park)position. The ...
Page 54 - Prolonged storage; Convertible top and padded molding care; Ensure that the convertible top is dry before installing the
9. Push the convertible top handleback up so that it locks intoposition. Prolonged storage It may be difficult to pull down and latch the convertible top afterprolonged storage with the top in the down position over the winter or incolder temperatures. This difficulty will decline over time with war...
Page 55 - Installing the removable top; Installation
Installing the removable top The front screw fittings must be checked to see that they arefirmly seated after driving a distance of approximately 50 to 60 km (30 to 40 miles). The removable top does not have the same crush resistance asan integrated steel roof in case of collision or rollover. The r...
Page 56 - Take the mounting key from the bag located in the trunk.
Once per year, apply a small amountof silicone lubricant,F5AZ–19553–AA, to the receivers asshown. The lubricant should besprayed directly into the hole toavoid contaminating the trim parts. 3. Lower the rear of the top intoposition so that the pins are placedinto the bracket receivers. 4. Position t...
Page 58 - Removing the top; Removable top storage rack
Removing the top It is recommended that you prepare the storage rack before removingthe top. See Removable top storage rack in this section. 1. Take the mounting key from the bag located in the trunk. 2. Using the mounting key, loosenthe two screws at the front of thetop. The two screws remainundeta...
Page 61 - Utility compartment
CELL PHONE USE The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...
Page 62 - POSITIVE RETENTION FLOOR MAT
POSITIVE RETENTION FLOOR MAT Position the driver floor mat so thatthe eyelet is over the pointed end ofthe retention post and rotateforward to lock in. Make sure thatthe mat does not interfere with theoperation of the accelerator or thebrake pedal. To remove the floormat, reverse the installationpro...
Page 63 - KEYS; SecuriLock; POWER DOOR LOCKS; Unlocking the doors; Locks and Security
KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to the SecuriLock 娂 passive anti-theft system section in this chapter for more ...
Page 64 - INTERIOR LUGGAGE COMPARTMENT RELEASE
The inside lights will not turn off if: • they have been turned on using the dimmer control or • any door is open. The battery saver feature will turn off the interior lamps 30 minutes afterthe ignition is turned to the 2 (OFF) position. Locking the doors Turn the key in the door cylinder to lock th...
Page 65 - REMOTE ENTRY SYSTEM; structures around the vehicle, or
Keep vehicle doors andluggage compartment locked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves in the trunk and riskinjury. Children should be taughtnot to play in vehicles. On hot days, the temperature in the trunk or vehicle interior canrise...
Page 68 - How to reprogram your remote entry transmitters; all remote entry transmitters
To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...
Page 69 - Illuminated entry
To reprogram the remote entrytransmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK) position to 4 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK)position and 4 (RUN). Note: The eighth turn must en...
Page 70 - Autolock; Relock
The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after theignition has been turned to the 2 (OFF) position. Autolock The autolock feature will lock the vehicle’s doors when...
Page 72 - Programming spare keys; coded key
• The theft indicator will illuminate for three seconds and then go out. • If the theft indicator stays on for an extended period of time orflashes rapidly, have the system serviced by your dealer. Key information Your vehicle is supplied with two coded keys (or three keys, if the valet feature is a...
Page 74 - Arming the system; Disarming the system; Triggering the anti-theft system
PERIMETER ALARM SYSTEM The perimeter anti-theft system will warn you in the event of anunauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL remote entry transmitters are taken to the dealership to aid in troubleshooting. Arming the s...
Page 75 - SEATING; event of a collision.; Adjustable head restraints; Push control to lower head restraint.; Seating and Safety Restraints
SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints Head ...
Page 76 - Using the manual lumbar support; Turn to adjust lumbar support.; Using the manual recline function; must be snug and low across the hips while the vehicle is moving.; Adjusting the driver’s power seat
Using the manual lumbar support The lumbar control is located on thefront of the driver’s seat cushion. Turn to adjust lumbar support. Using the manual recline function Never adjust the driver’s seat or seatback when the vehicle ismoving. To maximize restraint system effectiveness, the driver andpas...
Page 78 - Adjusting the passenger’s power seat; The control is located on the outboard side of the seat cushion.; SAFETY RESTRAINTS
Adjusting the passenger’s power seat The control is located on the outboard side of the seat cushion. Press the control to move the seatforward or backward. Heated seats (if equipped) To operate the heated seats: • Push the indicated side of thecontrol for maximum heat. • Push again to deactivate. •...
Page 79 - injury in a collision.; Combination lap and shoulder belts
Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag supplemental restraint system (S...
Page 81 - Automatic locking mode; How to use the automatic locking mode
Automatic locking mode How to use the automatic locking mode • Buckle the combination lap andshoulder belt. • Grasp the shoulder portion andpull downward until the entirebelt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety be...
Page 82 - When to use the automatic locking mode; Anytime; a child safety seat is installed in the vehicle. Refer to; Safety belt pretensioner; Safety belt maintenance
When to use the automatic locking mode • Anytime a child safety seat is installed in the vehicle. Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter. How to disengage the automatic locking mode Unbuckle the combination lap and shoulder belt and allow it to ret...
Page 83 - The BeltMinder
Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned t...
Page 84 - in 4 of us will be
If... Then... The driver’s safety belt is notbuckled before the vehicle hasreached at least 3 mph (5km/h) and 1-2 minutes haveelapsed since the ignitionswitch has been turned toON... The BeltMinder 娂 feature is activated - the safety belt warning lightilluminates and the warning chimesounds for 6 se...
Page 87 - Safety belt extension assembly
7. Confirmation of disabling BeltMinder 娂 is provided by the safety belt warning light flashing four times per second for three seconds. 8. Confirmation of enabling BeltMinder 娂 is provided by: • The safety belt warning light flashing four times per second for threeseconds. • Followed by three secon...
Page 88 - AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS); between an occupant’s chest and the driver air bag module.
Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Interior in the Cleaning chapter. AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) pre...
Page 89 - or Lincoln Mercury dealer.; Children and air bags; Air bags can kill or injure a child in a child seat.; place a
Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries. Steps you can take to properly position yourself away from the air bag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the s...
Page 91 - Side air bag system; Determining if the system is operational; Air bag readiness
Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS ...
Page 92 - Passenger front and side air bag ON/OFF switch; always
Passenger front and side air bag ON/OFF switch An air bag ON/OFF switchhas been installed in this vehicle. Before driving, always look at the face of the switch tobe sure the switch is in the properposition in accordance with theseinstructions and warnings. Failureto put the switch in a properpositi...
Page 94 - NHTSA deactivation criteria (excluding Canada)
occupant is not properly buckled up. The most effective way to reducethe risk of unnecessary air bag injuries, without reducing the overallsafety of the vehicle, is to make sure all occupants are properlyrestrained in the vehicle, especially in the front seat. This provides theprotection of safety b...
Page 95 - Transport Canada deactivation criteria (Canada Only); Child age 12 or under:
This vehicle has special energy management safety belts for thedriver and right front passenger. These particular belts are specifically designed to work with air bags to help reduce the risk ofinjury in a collision. The energy management safety belt is designed togive or release additional belt web...
Page 96 - increase the risk of injury in an accident.
This vehicle has special energy management safety belts for thedriver and right front passenger. These particular belts are specifically designed to work with air bags to help reduce the risk ofinjury in a collision. The energy management safety belt is designed togive or release additional belt web...
Page 97 - How does the side air bag system work?
How does the side air bag system work? The side air bag system consists ofthe following: • An inflatable nylon bag (air bag)with a gas generator concealedbehind the outboard bolster ofthe driver and front passengerseatbacks. • A special seat cover designed toallow air bag deployment. • The same warn...
Page 98 - the air bag will; If; SAFETY RESTRAINTS FOR CHILDREN; Air bag supplemental restraint system
If the side air bag hasdeployed, the air bag will not function again. The sideair bag system (including theseat) must be inspected andserviced by a qualifiedtechnician in accordance withthe vehicle service manual. If the air bag is not replaced, theunrepaired area will increase therisk of injury in ...
Page 99 - Important child restraint precautions; Children and safety belts; Child booster seats
Important child restraint precautions You are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally children who are four years oldor younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, youmust put them in safety seats made especial...
Page 100 - When children should use booster seats; Does the lap belt rest low across the hips?
Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend comfortably. Booster seats also make the shoulder belt fit betterand more comfortably for growing children. When children should use booster seats Ch...
Page 101 - Those with a high back.; The importance of shoulder belts; the body and may increase the risk of injury or death in a collision.
• Those with a high back. A backless booster would be abetter choice because the highback booster will place the childcloser to the instrument paneland airbag. Both can be used in any vehicle in a seating position equipped withlap/shoulder belts if your child is over 40 lb. (18 kg). The shoulder bel...
Page 105 - Allow the safety belt to retract to remove any slack in the belt.
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate itis in the automatic locking mode. 7. Pull the lap belt p...
Page 106 - Attaching child safety seats with tether straps; somewhere other than the correct tether anchor.
Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...
Page 110 - Tires, Wheels and Loading
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...
Page 111 - A number on the sidewall of
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...
Page 113 - Inflating your tires; blowout; Maximum Permissible Inflation Pressure; is the tire manufactures’
tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls for cuts, bruises and other damage. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case it needs to be repaired or replaced...
Page 114 - TIRE REPLACEMENT REQUIREMENTS
pressure should never be set lower than the recommended pressure onthe tire label or certification label. When weather temperature changes occur, tire inflation pressures alsochange. A 10° F (6° C) temperature drop can cause a correspondingdrop of 1 psi (7 kPa) in inflation pressure. Check your tire...
Page 115 - CHANGING THE TIRES
Only use replacement tires and wheels that are the same sizeand type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. Use of any tire orwheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in ...
Page 117 - Tire change procedure
• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheel The usage of a dissimilar spare tire/wheel can lead to impairment of thefollowing: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capabi...
Page 120 - WHEEL LUG NUT TORQUE SPECIFICATIONS
9. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torquespecification. Note: The jack cannot be properly stowed when a full size tire isplaced here. Secure the jack and the temporary spare tir...
Page 122 - Letter rating; For tires with a maximum speed capability over 149 mph (240
7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...
Page 124 - Indicates a tire, designated by; Load Range/Load Inflation; Indicates the tire’s
Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...
Page 125 - Vehicle
Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...
Page 127 - Highway hazards; Tire and wheel alignment
Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...
Page 128 - Tire rotation; scheduled maintenance information
The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more ev...
Page 130 - – is the weight of the vehicle including a full tank of; Vehicle Curb Weight; – is the weight of your new vehicle when you
SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss ofvehicle control. Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. Driving at very high speeds for extended periods of time may result indamage to vehicle components. The ...
Page 131 - Payload; – is the combined weight of cargo and passengers that the; “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO; for maximum
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door. Lookfor “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for m...
Page 132 - Cargo Weight; – includes all weight added to the Base Curb Weight,
Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. 2005 Thunderbird (tbr) Owners Guide (post-2002-fmt)USA (fus) Tires, Wheels and Loading 132
Page 133 - These; Trailer towing
GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...
Page 137 - See your local dealer for driveshaft
TRAILER TOWING Your vehicle is not equipped to tow. No towing packages are availablethrough Ford or Lincoln/Mercury dealers. RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) Follow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as ...
Page 138 - Starting the engine; Driving
STARTING Positions of the ignition 1. LOCK, locks the gearshift leverand allows key removal. (Thesteering wheel will not lock afterkey removal.) 2. OFF, shuts off the engine and allaccessories except the radio,convertible top control and thepower windows if accessory delay isactive. This position al...
Page 140 - If the engine does not start within five seconds on the first try,
• Turn the key to 4 (ON) withoutturning the key to 5 (START). Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine 1. Turn the key to...
Page 141 - BRAKES; Refer to
strongly recommended if you live in a region where temperatures reach-10°F (-23°C) or below. For best results, plug the heater in at least threehours before starting the vehicle. The heater can be plugged in the nightbefore starting the vehicle. To reduce the risk of electrical shock, do not use you...
Page 142 - Parking brake; ABS
ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. (I...
Page 143 - TRACTION CONTROL
TRACTION CONTROL 姟 Your vehicle is equipped with a Traction Control 娂 system. This system helps you maintain the stability and steerability of your vehicle,especially on slippery road surfaces such as snow- or ice-covered roadsand gravel roads. The system will allow your vehicle to make better useof...
Page 146 - Driving with a 5–speed automatic transmission
Driving with a 5–speed automatic transmission This vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive Shift Strategy offers the optimal transmission operation andshift quality. When the vehicle’s battery has been disconnected for anytype of service or repair, the transmission ...
Page 148 - Forced downshifts; Understanding gearshift positions
• Selecting 2 (Second) at higher speeds will cause the transmission todownshift to second gear at the appropriate vehicle speed. 1 (First) This position allows for first gear only. • Provides maximum engine braking. • Will not downshift into first gear at high speeds; will cause thetransmission to d...
Page 149 - Manual shift mode; the transmission to upshift one; command; the transmission to downshift one; next lower
Manual shift mode With the gearshift lever in D5(Overdrive), the gearshift lever canbe moved to the right and into themanual shift mode. The transmissionwill remain in the manual shift modeuntil the gearshift lever is movedback to D5 (Overdrive). + and - position operation These positions allow the ...
Page 150 - Recommended upshift schedule; If your vehicle gets stuck in mud or snow; DRIVING THROUGH WATER; Wet brakes do not stop the vehicle as quickly as dry brakes.
• If shifter (-) is tapped more than once in rapid succession, thetransmission will downshift only into the next lower gear, then when thevehicle reaches a speed below a calibrated entry speed, the transmissionwill allow a downshift into the next lower gear if again selected by thedriver. This is to...
Page 151 - Owner Information Guide; Roadside Emergencies
GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...
Page 152 - Roadside coverage beyond basic warranty; HAZARD FLASHER; With extended use, the flasher may run down your battery.; FUEL PUMP SHUT-OFF SWITCH
Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...
Page 153 - Always replace a fuse with one that has the specified amperage
This switch is located in the driver’sfootwell, behind the kick panel. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a few seconds and returnthe key to...
Page 154 - Standard fuse amperage rating and color; Passenger compartment fuse panel
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...
Page 155 - The fuses are coded as follows.; Location; Starter relay coil
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A Starter relay coil 2 5A Radio start signal 3 5A Anti-lock Brake System (ABS)module 4 5A Cluster, Powertrain ControlModule (PCM) relay coil, Inertiaswitch, Transmission park switch 5 ...
Page 157 - Battery
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 34 5A Outside mirrors 35 5A Brake pedal switch Relay 1 — Not used Front power distribution box The front power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses t...
Page 160 - Rear power distribution box; refilling fluid reservoirs.
Rear power distribution box The rear power distribution box islocated in the luggage compartmentunder the spare tire well cover. Thepower distribution box containshigh-current fuses that protect yourvehicle’s main electrical systemsfrom overloads. Always disconnect the battery before servicing high ...
Page 162 - Lockable and
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 29 30A** Rear defroster 30 — Not used 31 40A** Convertible top motor 32 30A** SSP2 Relay 001 Full ISO SSP1 Relay 002 Full ISO SSP4 Relay 003 Full ISO Rear defroster Relay 004 Full ISO SSP3 Relay 005 Full ISO SSP2 Relay 006 — Not ...
Page 163 - touch. Set the parking brake on; Connecting the jumper cables; In the illustrations,
may have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Over time, theadaptive learning process will fully update transmission operation to itsoptimum shift feel. 1. Use only a 12–volt supply to start your vehicle. 2. Do no...
Page 165 - explosion of the gases that surround the battery.; Jump starting; Start the engine of the disabled vehicle.
4. Make the final connection of the negative (-) cable to the spare tiretie-down stud. (Your vehicle may be equipped with a plastic cap on topof the tire tie-down stud. This cap must be removed prior to attachingthe cable to the stud.) Do not connect the end of the second cable to the negative (-)te...
Page 166 - Removing the jumper cables; Remove the jumper cable from the spare tire tie-down stud.
Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the spare tire tie-down stud. 2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery. + – + – + – + – 2005 Thunderbird (tbr) Owners Gui...
Page 167 - relearn
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...
Page 168 - WRECKER TOWING
WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...
Page 169 - In the United States:; Customer Assistance
GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...
Page 171 - The Dispute Settlement Board is:
In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...
Page 172 - What kinds of cases does the Board review?; a non-Ford dealership; Board membership; The Board consists of:
• available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedures and/or to discontinue this service without notice and withoutincu...
Page 174 - Making a decision; To request a DSB Brochure/Application
before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be requested by the Board as well. Making a decision Board members review all available information related to eachcomplaint, including oral presentation...
Page 175 - FORD EXTENDED SERVICE PLAN
The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings. In the CAMVAP program,...
Page 177 - Obtaining a French owner’s guide
Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing toFord ...
Page 178 - Wash the vehicle first.; Cleaning
WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your dealer. • Using high water pressure or wand-type car washes against theconvertible top and windows may cause water leaks andpossi...
Page 179 - PAINT CHIPS; Always read the instructions before using the products.; ALUMINUM WHEELS AND WHEEL COVERS
• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your dealer has touch-...
Page 180 - WINDOWS AND WIPER BLADES
• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaningthe engine. • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damag...
Page 181 - INSTRUMENT PANEL AND CLUSTER LENS; If your vehicle is equipped with
• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer solution. Be sure to replace wiper blades when theyappear worn or do not function properly. INSTRU...
Page 182 - INTERIOR; Remove dust and loose dirt with a vacuum cleaner.; LEATHER SEATS; In some instances, color or dye transfer can occur when wet; UNDERBODY
INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material...
Page 183 - FORD AND LINCOLN MERCURY CAR CARE PRODUCTS; Motorcraft Custom Clear Coat Polish (ZC–8–A)
FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the style ...
Page 184 - SERVICE RECOMMENDATIONS; PRECAUTIONS WHEN SERVICING YOUR VEHICLE; Maintenance and Specifications
SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provi...
Page 185 - OPENING THE HOOD; Lift the hood until the lift cylinders hold it open.; IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT
OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located at the bottomleft of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood by pushing the handletoward the passenger side of thevehicle. 3. Li...
Page 186 - WINDSHIELD WASHER FLUID; Lubricant specifications; ENGINE OIL
5. Air filter assembly 6. Power steering fluid reservoir 7. Windshield washer fluid reservoir 8. Power distribution box WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specif...
Page 187 - If the oil level is; between the MIN and MAX marks,; the oil level is; Adding engine oil; Checking the engine
3. Set the parking brake and ensure the gearshift is securely latched in P(Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil l...
Page 188 - Install the indicator and ensure it is fully seated.; Engine oil and filter recommendations
2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the eng...
Page 189 - BATTERY
Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material and design specifications, start-upengine noises or knock may be experienced.It is recommended you use the appropriate M...
Page 190 - Wash hands after handling
When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...
Page 191 - scheduled maintenance information.; 0–50 mixture of coolant and water provides the following:; RETURN
If the battery has been disconnected or a new battery has been installed,the short drop glass, clock and the preset radio stations must be resetonce the battery is reconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yo...
Page 192 - Adding engine coolant; until the appropriate fill level is obtained.
When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...
Page 193 - Do not add extra inhibitors or additives to the coolant.
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...
Page 194 - Recycled engine coolant
coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant. To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant ...
Page 195 - Used engine coolant should be disposed of in an appropriate; Coolant refill capacity; Refill capacities; Severe climates; If you drive in extremely hot climates:; NEVER decrease the coolant concentration below 40%.
Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section....
Page 196 - What you should know about fail-safe cooling; How fail-safe cooling works
What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before incremental component damage is incurred.The “fail-safe” distance depends on ambient temperatures, vehicle loadand terrain. How fail-safe cooling work...
Page 197 - WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS; Gasoline may contain benzene, which is a cancer-causing agent.
4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Re-start the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehi...
Page 199 - Refueling; Fuel Filler Cap
Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...
Page 201 - If you have run out of fuel:; Fuel Filter
Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage. Fuel quality If you are experiencing star...
Page 203 - Have the vehicle loading and distribution the same every time.; Calculating fuel economy; Habits
• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...
Page 207 - POWER STEERING FLUID
soon light is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may not pass the I/M test with the Check engine/Service engine soon light on. If the vehicle’s powertrain system or its battery has just been serviced,the on-board diag...
Page 208 - AIR FILTER
BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...
Page 209 - Air filter
Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Air filter 1. Loosen the hose clamp on theoutlet tube at the air filter housing. 2. Release the two clamps thatsecure the cover to the air filterhousing and place the cover aside. 3. Remove ...
Page 211 - REFILL CAPACITIES
For PCV valve replacement, see your dealer or a qualified servicetechnician. Refer to the scheduled maintenance information for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material anddesign specifications for your vehicle, such as a Motorcraf...
Page 212 - Lubricant Specifications
Fluid Ford PartName Application Capacity Power steeringfluid MotorcraftMERCON 威 ATF All Fill to MAX lineon reservoir Rear axle 3 Motorcraft SAE75W-140Synthetic RearAxle Lubricant All 2.5–2.7 pints(1.2–1.3L) Fuel tank N/A All 18.5 gallons(70.0L) Transmissionfluid 4 MotorcraftMERCON 威 V ATF Automatic(...
Page 213 - Brake fluid
LUBRICANT SPECIFICATIONS Item Ford partname Ford partnumber Fordspecification Brake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid 1 PM-1 ESA-M6C25-Aand DOT 3 Doorweatherstrips SiliconeLubricant XL-6 ESR-M13P4-A Door latch,hood latch,auxiliary hoodlatch, doorhinges, strikerplates, sea...
Page 214 - Item
Item Ford partname Ford partnumber Fordspecification Power steeringfluid MotorcraftMERCON 威 ATF XT-2-QDX MERCON 威 Rear AxleLubricant Motorcraft SAE75W-140Synthetic RearAxle Lubricant 2 XY-75W140–QL WSL-M2C192-A Automatictransmissionfluid MotorcraftMERCON 威 V ATF 3 XT-5-QM MERCON 威 V Windshieldwasher...
Page 217 - Engine number
Vehicle identification number (VIN) The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) The vehicle identification number (VIN) contains the followin...
Page 219 - Accessories
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...
Page 221 - Index
A Accessory delay ..........................40 Air bag supplemental restraintsystem ....................................88, 96 and child safety seats ..............89description ..........................88, 96disposal ......................................98driver air bag ......................90, ...
Page 226 - Windows
Windows power .........................................40 Windshield washer fluid andwipers ..........................................38 checking and adding fluid .....186replacing wiper blades .............38 Wrecker towing .........................168 2005 Thunderbird (tbr) Owners Guide (post-2002...