Ford 2005 Mustang v.3- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

Event Data Recording Other modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash event. Therecorded information may assist in the investigation of such an event.The modules may record information about both the vehicle and theoccupant...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Base instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights ...

Service Engine Soon: The Service Engine Soon indicator light illuminates when the ignition is firstturned to the ON position to checkthe bulb. Solid illumination after the engine is started indicates the OnBoard Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (O...

Anti-lock brake system (ifequipped): If the ABS light stays illuminated or continues to flash, amalfunction has been detected, havethe system serviced immediately byyour authorized dealer. Normal braking is still functional unless the brakewarning light also is illuminated. Airbag readiness: If this...

Traction Control 娂 active (if equipped): Flashes when the Traction Control 娂 is active. If the light remains on a malfunction hasbeen detected; have the systemserviced immediately, refer to the Driving chapter for more information. Overdrive off (automatictransmission): Illuminates when the overdriv...

Turn signal: Illuminates when the left or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a burned out bulb. High beams: Illuminates when the high beam headlamps are turned on. Daytime running lamps (DRL)(if equipped): Illuminates when the Day...

GAUGES Base instrument cluster gauges Optional instrument cluster gauges Refer to Message Center (if equipped) in the Driver Controls chapter to select one of six preset colors or one user definable color (MyColor)for the nighttime gauge backlighting. 2005 05+ Mustang (197)Owners Guide (post-2002-fm...

AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED) 1. / Tuner: Press to manually go up or down the radiofrequency. Also use in menu modeto select various settings. 2. Phone/mute: Press to mute the playing media. Press again to returnto the playing media. 3. Menu: Press to toggle through the followin...

Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise.Recommended level is 1–3. Level 0 turns the feature off and level 7 isthe maximum setting. Press MENU to access and use / / SEEK to adjust the volume setting. The level wi...

16. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decreasevolume.If the volume is set above a certainlevel and the ignition is turned off,the volume will come back on at a“nominal” listening level when the ignition switch is turned back on. 17. CD: Press to enter CD mode. If a CD is already ...

from 01–01 to 99–99. The first two digits denote the folder number andthe last two digits denote the track number within that folder. • Creating discs with only one level of folders will help with navigationthrough the disc files. ACCESSORY DELAY With accessory delay, the window switches and radio m...

CD units are designed to play commercially pressed 4.75 in (12 cm)audio compact discs only. Due to technical incompatibility, certainrecordable and re-recordable compact discs may not functioncorrectly when used in Ford CD players. Irregular shaped CDs,CDs with a scratch protection film attached, an...

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Temperature selection: Controls the temperature of the airflow in the vehicle. 2. Mode selections: Controls the location of the airflow in the vehicle. See the following for a brief description of each selection. MAX A/C: Distributes recirculated air thr...

6. Fan speed adjustment: Controls the volume of air circulated in the vehicle. Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the (defrost) position. • To reduce humidity build up inside the vehicle, do not drive with theairflow selector...

REAR WINDOW DEFROSTER (R ) Ensure that the ignition is in the 3 (ON) position. Press the control toclear the rear window of thin ice and fog. The LED will illuminate. The rear window defroster turns off automatically after 10 minutes, orwhen the ignition is turned to the 1 (OFF/LOCK) position. To ma...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Foglamp control (if equipped) The foglamps can be turned onwhen the headlamp control is inthe or position and the high beams are not on. Pull the headl...

Headlamp vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from ...

6. Pull the bulb straight from thesocket. Install the new bulb in reverseorder. Replacing backup bulbs The backup lamp is located in the tail lamp assembly. Follow the samesteps to replace either bulb. 1. Make sure headlamp switch is inOFF position, then open the trunk. 2. Carefully remove fasteners...

Replacing license plate lamp bulbs 1. Make sure the headlamp switch isin the OFF position, then removethe two screws and the license platelamp assembly. 2. Remove bulb socket by turningcounterclockwise. 3. Carefully pull the bulb out fromthe socket. Install new bulb(s) in reverse order. 2005 05+ Mus...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control up oneposition. Adjust the rotary control to thedesired speed setting. For normal or low speed wiperoperation, move control up twopositions from OFF. For high speed wiper operation,move control up three positionsfrom OFF...

Changing the wiper blades 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damage theoutlet and blow the fuse. Do not hang any type of accessory oraccessory bracket from the plug. Improper use of the poweroutlet can cause damage ...

When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and pull the switches to openand close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (to the f...

Bounce Back Override (Front windows only) To override Bounce Back, within 2 seconds after reaching Bounce Backposition, if the switch is moved from the Neutral to the Express Upposition the window will travel up with no bounce back protection. If the switch is released before the window reaches full...

• Push down and hold the switch to open. • Pull up and hold the switch to close. POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directi...

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control. Turning off speed control There are two ways to turn off the speed control: • Press the speed control OFFcontrol. • Turn OFF the ignition. Note: When you turn off the speed control or the ignition, your spee...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status precededby a brie...

1. Press SETUP to get to theDISPLAY COLOR set up menu. 2. Pressing RESET will scrollthrough the following selectablecolors: Green Blue Purple White Orange Red MyColor Adjust (to define MyColor) Adjusting MyColor 娂 : MyColor 娂 is a user defined backlighting color. The backlighting colors are achieved...

Single mode display Dual mode display The DTE function will display LOW FUEL LEVEL and sound a tone forone second when you have approximately 50 miles (80 km) to empty. Ifyou RESET this warning message, this display and tone will returnwithin 10 minutes. DTE is calculated using a running average fue...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center will cyclethe display to show all warnings by displaying each one for 4 seconds. The message center will display the las...

Warning display Status Check brake system Warning returns after the ignition keyis turned from OFF to ON. Low brake fluid level Service ETC system Trunk ajar Park brake on Security event occurred Turn signal on reminder DRIVER’S DOOR AJAR. Displayed when the driver’s door is not completely closed. P...

• Engine sensor Contact your authorized dealer as soon as possible if these messagesoccur on a regular basis. POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tolock in. Make sure that the mat doesnot ...

3. Unclamp the top from thewindshield header at both the rightand left sides by pulling each handledown and rearward until the handleclears the windshield header. Thehandles are flush with the headerwhen in the closed position. Note: If the top has not been lowered for some time and sticks to the wi...

Installation of the boot (if equipped) Be sure the boot is secure on the vehicle before driving. 1. Install the boot on the vehicle by hooking the boot retaining clips onthe back panel.2. Install the boot on the right side tucking in the front part of the bootin the quarter panel and hooking the ret...

Storing the boot 1. Position the boot right-side up and fold each side of the boot inward. 2. Turn the boot upside down and fold the left side of the boot inward. 3. Fold the right side inward and secure the boot with the strap. Stow the boot in the trunk. 2005 05+ Mustang (197)Owners Guide (post-20...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

Autolock (if equipped) On vehicles equipped with an automatic transmission, this featureautomatically locks all vehicle doors when: • all doors are closed, • the ignition is in the 3 (ON) position, • the brake is pressed before reaching 5 mph (8 km/h), and • then the vehicle increases to more than 5...

• The driver’s door is unlocked when the key is inserted in the driverdoor key cylinder and turned to the unlock position. The driver’s dooris locked when the key is inserted in the driver door key cylinder andturned to the lock position. Note: Locking the driver door with the key does not lock the ...

How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. To reprogram the remote entrytransmitters: 1. Ensure the vehicle iselectronically unlocked. 2. Put the key in the ignition. 3. Cycle eight times ra...

The battery saver will shut off the interior lamps 10 minutes after theignition has been turned to the 1 (OFF/LOCK) position and a door is leftopen, and in 30 minutes if the dome lamp control is left on and theignition has been turned to the 1 (OFF/LOCK) position. The batterysaver will also shut off...

If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. Ifthis occurs, the vehicle should be taken to an authorized dealer forservice. Automatic arming The vehicle is armed immediatelyafter switching the ignitio...

Programming spare keys You can program your own coded keys to your vehicle. Please read andunderstand the entire procedure before you begin. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use Securilock 娂 keys. • You must have two previously programmed coded keys (keys thatalre...

If there is any potential active anti-theft problem with your vehicle,ensure ALL remote entry transmitters are taken to an authorized dealer to aid in troubleshooting. Arming the system When armed, the active anti-theft system is designed to notify you of anunauthorized entry. When unauthorized entr...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Pull lever up to adjust the angle ofthe seatback. Four-way seat adjust (driver side only) Pump the handle upwards to raisethe cushion and pump downward tolower the cushion to the desiredlocation. Using the power lumbar support (if equipped) The power lumbar control is locatedon the top of the seat s...

Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

position. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower airbag output level. Front passenger sensing system For airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants th...

Safety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit in the backseat where they can be properly restrained. Never let a passenger hold a child on his or her lap while thevehic...

Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Combination lap and shoulder belts The belt guide is intended to improve access to the safety belt and...

movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph (8 km/h)or more, the combination safety belts will lock to help reduce forwardmovement of the driver and passengers. Automatic locking mode The automatic locking mo...

How to disengage the automatic locking mode Ford Motor Company recommends that all safety belt assembliesand attaching hardware should be inspected by an authorized dealer after any collision. Safety belt assemblies not in use during acollision should also be inspected and replaced if either damage ...

Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be seriously injured in a crash duringour lifetime. “I’m not going far” 3 of 4 fatal crashes occur within 25 miles...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

• The gearshift is in P (Park) (automatic transmission) • The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled To reduce the risk of injury, do not deactivate/activate theBeltMinder 娂 feature while driving the vehicle. 1. Turn the ignition switch to ...

Do not use extensions to change the fit of the shoulder beltacross the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All saf...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your authorized dealer. Modifying or adding equipment to the front end of the vehicle(including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag syst...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration sufficientto cause the airbag sensors to closean electrical circuit that initiatesairbag inflation. The fact that theairbags did not inflate in a collisi...

• a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness ligh...

If the side airbag hasdeployed, the airbag will not function again. The sideairbag system (including theseat) must be inspected andserviced by an authorizeddealer . If the airbag is not replaced, the unrepaired area willincrease the risk of injury in acollision. Determining if the system is operatio...

or younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, youmust put them in safety seats made especially for children. Many statesrequire that children use approved booster seats until they are eightyears old. Check your local and state or provincial laws for specificrequirements rega...

Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend comfortably. Booster seats also make the shoulder belt fit betterand more comfortably for growing children. When children should use booster seats Ch...

• Those with a high back. If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Both can be used in any vehicle in a seating position equipped withlap/shoulder belts if your child is over 40 lb....

Carefully follow all of the manufacturer’s instructions includedwith the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a suddenstop or collision. Rear-facing child seats or infant carriers should never be placedin the front s...

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate itis in the automatic locking mode. 7. Pull the lap belt p...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

Note: The attachments for the convertible boot located on the backof the head restraints are not tetheranchors. 2005 05+ Mustang (197)Owners Guide (post-2002-fmt)USA (fus) Seating and Safety Restraints 115

If the safety seat is not anchored properly, the risk of a childbeing injured in a collision greatly increases. Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments Some child safety seats have two rigid or web mounted attachments thatconnect to two anchors at certai...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear andremove stones, nails, glass or other objects that may be wedged in thetread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls...

Maximum Permissible Inflation Pressure is the tire manufactures’ maximum permissible pressure and/or the pressure at which themaximum load can be carried by the tire. This pressure is normallyhigher than the manufacturer’s recommended cold inflation pressurewhich can be found on the Safety Complianc...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

the road in adverse (wet, snowy, etc.) conditions. Visually check yourtires for uneven wear, looking for high and low areas or unusuallysmooth areas. Also check for signs of tire damage. When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to prevent your vehiclefrom skiddin...

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Never spin the tires in excess of the 35 mph (55 km/h) pointindicated on the speedometer. Highway h...

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar...

• The suspension insulation and bumpers will help prevent vehicledamage. Do not remove these components from your vehicle whenusing snow tires and chains. VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo + passengers. GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located o...

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The tra...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. Note: The ignition key cannot be removed from the ignition unlessthe gearshift lever is securelylatched in P (Park). 2. ACCESSORY, allows the electricalaccessories su...

Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel until thekey turns freely. 2. Turn the key to 4 (START), thenrelease the key as soon as theengine starts. Note: If the engine does not start within fi...

BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-outand should be inspected by an authorized dealer. If the vehicle hascontinuous vibration or shudder in the steering wheel while braking, thevehicle ...

Brake Assist (if equipped) The Brake Assist system provides full braking force during panic brakingsituations. It detects a rapid application of the brake pedal andmaximizes the amount of brake booster assist, helping the driver toachieve maximum braking pressure. Once a panic brake application isde...

• Do not operate the vehicle with a low power steering pump reservoirfluid level (below the MIN mark on the reservoir). If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for:...

• Overdrive mode is automatically returned each time the key is turnedoff. 3 (Third) This position allows for third gear only. • Provides engine braking. • To return to D (Drive) without Overdrive, move the transmission shiftlever into the D (Drive) position. • Selecting 3 (Third) at higher speeds w...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transmission has a starter interlock that prevents crankingthe engine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then pu...

Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 11 mph (18 km/h) 2 - 3 19 mph (31 km/h) 3 - 4 30 mph (48 km/h) 4 - 5 40 mph (64 km/h) Reverse 1. Make sure that your vehicle is at a complete stop before you shift intoR (Revers...

DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth isunknown. Traction or brake capability may be limited and if the ignitionsystem gets wet, your engine may stall. Water may also enter yourengine’s air intake and severely damage your engine. If driving throug...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

The fuel pump shut-off switch islocated in the driver’s footwell, bythe hood release To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a few seconds and re...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — — — 30A Green Green Green Pink Pink 40A — — Orange Green Green 50A — — Red Red Red 60A...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. Do not probe the contacts for the fuses and relays in the powerdistribution box as damage w...

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 61 20A** Power point #1 (Instrumentpanel) 62 20A** SJB #7 (Instrument panel fusebox) 63 30A** SJB #6 (Instrument panel fusebox) 64 20A** Power point #2 (Console) 65 30A** ABS #2 66 — Not used 67 30A** SJB #4 (Instrument panel fus...

1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on b...

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s eng...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMot...

Board membership The Board consists of: • Three consumer representatives • An authorized dealer representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom authorized dealer management, recognized for t...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Business Park #3Allen Park, Michigan 48101U.S.A.Telephone: (313) 594-4857FAX: (313) 390-0804 If you are in another foreign country, contact the nearest authorizeddealer. If the authorized dealer employees cannot help you...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). WINDOWS AND W...

INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then with a clean, drycloth, or use Motorcraft Dash & Vinyl Cleaner (ZC-38-A). • Avoid cleaners or polish that increase the gloss of the upper portion ofthe instrument panel. The dull finish in this area helps protec...

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over theleather. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleaner (ZC-11–A). Dry the area with a soft cloth. • To help maintain its resiliency and color, use the Motorcraft DeluxeLe...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer ca...

2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, p...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power distribution box...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

5. Locate and carefully remove the engine oil level indicator (dipstick). • 4.0L V6 engine • 4.6L 3V V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. • If the ...

• 4.0L V6 engine • 4.6L 3V SOHC V8 engine • Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Chec...

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above thenormal operating ra...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to scheduled maintenance information for the servi...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

will not affect function or durability of the transmission. Over time theadaptive learning process will fully update transmission operation to itsoptimum shift feel. If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once th...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant(yellow-colored), VC-7–A (U.S., except CA, OR and NM),VC-7–B (CA, OR and NM), meeting For...

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come outforcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section....

4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Restart the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehic...

• Extinguish all smoking materialsand any open flames beforerefueling your vehicle. • Always turn off the vehicle beforerefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuel such as gasoline is highly toxic and ifswallowed can cause death or permanent injury. If fuel is swallowed,c...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith the recommended octane rating, see your authorized dealer toprevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hes...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

soon light is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may not pass the I/M test with the Check engine/Service engine soon light on. If the vehicle’s powertrain system or its battery has just been serviced,the on-board diag...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Note: There are two different manual transmissions used in thisvehicle and they have different fluid levels. For vehicles equipped with aV6 engine the corre...

LUBRICANT SPECIFICATIONS Item Ford partname Ford partnumber Fordspecification Brake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid PM-1 ESA-M6C25-A Doorweatherstrips Silicone SprayLubricant XL-6 ESR-M13P4-A Door latch, hoodlatch, auxiliaryhood latch,striker plates,seat tracks andfuel ...

Item Ford partname Ford partnumber Fordspecification Engine oil 4.6L engine Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 SuperPremium MotorOil (Canada) XO-5W20-QSP(US)CXO-5W20–LSP12 (Canada) WSS-M2C 930-Awith APICertificationMark 4.0L V6 engine Motorcraft SAE5W-30 Prem...

Item Ford partname Ford partnumber Fordspecification Manualtransmissionfluid – 4.0LV6/4.6L V8 MotorcraftMERCON 威 ATF XT-2-QDX MERCON 威 Disc brakecaliper rails MotorcraftSilicone BrakeCaliper Greaseand DielectricCompound XG-3-A ESE-M1C171-A Windshieldwasher fluid MotorcraftPremiumWindshieldWasherConc...

Vehicle identification number (VIN) The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) The Vehicle Identification Number (VIN) contains the followin...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Accessory delay ..........................45 Air cleaner filter .......................225 Airbag supplemental restraintsystem ............................96–97, 103 and child safety seats ..............98description ........................97, 103disposal ....................................105dr...