Ford 2005 Freestyle v.2- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Check fuel cap: Illuminates when the fuel cap may not be properlyinstalled. Continued driving withthis light on may cause the Checkengine warning light to come on,refer to Fuel filler cap in the Maintenance and Specification chapter. Brake system warning light: To confirm the brake system warninglig...

Parking brake ON: Sounds when the parking brake is left ON and driven. If the warning stays on after the park brake is off, contact yourdealer as soon as possible. GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At norma...

AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED) 1. / Tuner: Press to manually go up or down the radiofrequency. Also use in menu modeto select various settings. 2. Phone/mute: Press to mute the playing media. Press again to returnto the playing media. 3. Menu: Press to toggle through the followin...

14. Seek: Press to access the previous strong station or track. 15. AM/FM: Press to select AM/FM frequency band. 16. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decreasevolume.If the volume is set above a certainlevel and the ignition is turned off,the volume will come back on at a“nominal...

FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a Family Entertainment DVD Systemwhich allows you to watch DVDs, play music CDs, and to plug in andplay video game systems. Please review this material to become familiarwith the Family Entertainment System (FES) feature...

4. ENTER control Press to select the function highlighted on the active menu. ENTER mayalso be used by some user interactive discs during movie play. 5. MENU control Press to bring up the disc menu. 6. AUX control Press to switch DVD player from play mode to auxiliary mode. 7. Auxiliary jacks Input ...

Remote control 1. REWIND control Press to reverse the direction of the DVD movie. 2. FAST FORWARD control Press to advance the direction of the DVD movie. 3. PLAY/STOP control When playing, press PLAY/STOP to stop the disc. When stopped, pressPLAY/STOP to play the disc. 4. SEEK control Press to reve...

8. VOLUME control Press (+) to increase or (-) to decrease the volume level over vehiclespeakers. Dual play mode Press the radio preset controls 2and 4 at the same time to enable ordisable dual play. During dual play, the rear vehicle speakers will be deactivated and thewireless headphones will beco...

Family Entertainment DVD System protection circuits High temperature sensor circuit • Excessively high temperatures may cause damage to the DVD player. • When the temperature of the DVD player becomes too hot, the hightemperature sensor circuit stops machine operation. DVD/CD HOT willbe displayed on...

On-screen indicators Each time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible indicators: 1. DVD/CD Title. 2. DVD/CD chapter/track number. 3. MEDIA COUNTER — displays current viewing time of desired media.(MINUTES : SECONDS). 4. ...

The front glass on the flip-down liquid crystal display (LCD) maybreak when hit with a hard surface. If the glass breaks, do not touch the liquid crystalline material. In case of contact with skin, washimmediately with soap and water. Do not expose the flip-down liquid crystal display (LCD) to direc...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theairflow selector in the O (OFF) or with recirculated air engaged. • Do not put objects under the front se...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED) 1. Defrost : Distributes outside air through the windshield defroster and demister vents. Can be used to clear ice or fog from the windshield. 2. Passenger temperature control: Press to increase/decrease the airflow temperature f...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REARPASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) 1. Defrost : Distributes outside air through the windshield defroster and demister vents. Can be used to clear ice or fog from the windshield. 2. Rear temperature control: Press to enable the auxilia...

4. Set the fan to the highest speed. 5. Direct the outer instrument panel vents towards the side windows. Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sudden stop. AUXILIARY CLIMATE CONTROL (IF EQUIPPED) 1. Fan speed: Turn to select the...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of theheadlamp...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control up oneposition. Adjust the rotary control to thedesired speed setting. Mist function: To activate mist, push control down from the OFFposition and release to get one wipe. For normal or low speed wiperoperation, move con...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: 2 — One second interval rear wiper. 1 — Ten second interval rear wiper. O — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear ...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down and hold the steeringwheel release control. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Pull the steering wheel releasecontrol up. This will lock thesteering wheel in position. Never adjust the steering wh...

Conversation mirror (if equipped) The conversation mirror allows the driver to view the rear seating area. This does not replace the rear view mirror. Pull down on the housing to lock itin place. Adjust the mirror, asneeded, in any direction. The rear view mirror may have to beadjusted to its lower ...

POWER WINDOWS Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the proximity of the ...

If the switch is pressed and held to the normal open or ONE TOUCHDOWN position during a ONE TOUCH UP event, the window will stop. If,after 1/2 second the switch is still held, the window will perform anormal open or ONE TOUCH DOWN. Window lock The window lock feature allows onlythe driver to operate...

MIRRORS Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mirrors in place...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control(located on the instrument panel) toadjust accelerator and brake pedal. • Press the top of...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or pressCNCL (Cancel). This will noterase your vehicle’s previously setspeed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set s...

In any mode: • Press VOL up or down to adjustthe volume. • Press MUTE to mute the volume. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up toventilate the vehicle. To open the moon roof: The moon roof is equipped with anautomatic, one-touch, expressopenin...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitterswith a single built-in device. This feature will learn the radio frequencycodes of most transmitters to opera...

Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLink 威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or otherrolling code equipped device), repeat...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status precededby a brie...

Warnings Status Low brake fluid Warning returns after the ignition keyis turned from OFF to RUN Liftgate ajar (if equipped) Trunk ajar (if equipped) Check Traction Control (ifequipped) Washer Fluid level low Coolant level low Check engine Change oil soon Oil change required Data error DRIVER’S DOOR ...

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment with powerpoint • Gear Shift • Cup holders • Rear vent and cup holders (ifequipped) Use only soft cups in the cupholder. Hard objects can injure youin a collision. Second row center co...

A driver’s first responsibility is the safe operation of the vehicle.The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe tooperate Mobile Communications Equipment. LIFTGATE Unlock the liftgate (but do notrelease it) wit...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your dealer suppliedkeys, replacement keys are available throug...

1. Place the key in the ignition and turn the ignition to the 3 (RUN)position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn ...

The remote entry system activates the illuminated entry feature; thisfeature turns on the lamps for 25 seconds or until the ignition is turnedto the 3 (RUN) position. The inside lights will not turn off if: • they have been turned on using the dimmer control or • any door is open. The battery saver ...

2. Press the SET control on thedriver’s door panel. 3. Within 5 five seconds, press the 1or 2 control on the driver’s doorpanel to which you would like toassociate with the seat, mirrors andadjustable pedals and Driver 1 orDriver 2 positions. 4. Repeat this procedure for theother Driver position if ...

5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmittershould operate normally after battery replacement. Replacing lost remote entry transmitters If you would like to have your remo...

Illuminated entry The interior lamps illuminate when the remote entry system, the keylessentry system keypad (if equipped) or the door lock cylinder (on vehiclesequipped with the perimeter alarm system) is used to unlock thedoor(s). The illuminated entry system will turn off the interior lights if: ...

KEYLESS ENTRY SYSTEM You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • activate or deactivate theautolock feature. The keypad can be operated withthe factory set 5–digit entry code;this code is located on the owner’swallet card in the glove box, ismarked on the...

3. Enter factory-set 5–digit entry code. 4. Press and hold the 7 • 8. While holding the 7 • 8 press the 3 • 4. 5. Release the 3 • 4. 6. Release the 7 • 8. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has beenenable...

If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. Ifthis occurs, the vehicle will not start and should be taken to anauthorized dealer for service. Automatic arming The vehicle is armed immediatelyafter s...

Programming spare keys You can program your own coded keys to your vehicle. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock 娂 keys. • You must have two previously programmed coded keys (keys thatalready operate your vehicle’s engine) and the new unprogrammedkey(s)...

If the key was not successfully programmed, it will not start yourvehicle’s engine and the theft indicator light will flash on and off. Wait 20seconds and you may repeat Steps 1 through 8. If failure repeats, bringyour vehicle to your dealer to have the new key(s) programmed. To program additional n...

• Press the 7 • 8 and 9 • 0 controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdownwhen any of the above actions occurbefore the vehicle becomes armed. Each door, the hood or the liftgateis armed individually, and if any areope...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints Head ...

Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Using the manual lumbar support (if equipped) The lumbar support control islocated on the outboard side of theseatback. Move t...

Folding down the front passenger seatback (if equipped) The front passenger seatback can befolded to a horizontal position tomake room for a long load. To foldthe seatback: 1. Move the seat as far back aspossible. 2. Push the head restraint releasebutton and move the head restraintfully down. 3. Pul...

• in any gearshift position if the ignition is not in the RUN position. • only in Park or Neutral if the ignition is in the RUN position. A memory seat position may be programmed at any time. The memory positions are also recalled when you press your remoteentry transmitter UNLOCK control if the tra...

Lift the handle located on the sideof the seat. The seatback will fold flat. Lift the handle all the way up untilthe seat releases from the floor.Rotate the seat forward to allowaccess to the third row. To return the seatback to the floorfrom tumbled position, rotate theseat down until you hear it l...

To return the seatback to the floorfrom tumbled position, rotate theseat down until you hear it latchingto the floor. To return the seatback to theupright position • Lift the seatback toward the rearof the vehicle, and • Rotate the seatback until youhear a click, locking it in theupright position. N...

release the seat floor latch while vehicle is in motion. Do not operate thevehicle with seats in tumbled position. Always latch the vehicle seat to the floor, whether the seat isoccupied or empty. If not latched, the seat may cause injury during a sudden stop. Stowing the third row bench or split be...

SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of air bag-related injuries. The system is able to analyzedifferent occupant conditions and crash s...

Driver and passenger dual-stage air bag supplemental restraints The dual-stage air bags offer the capability to tailor the level of air baginflation energy. A lower, less forceful energy level is provided for morecommon, moderate-severity impacts. A higher energy level is used forthe most severe imp...

(child size) occupants from air bag deployments when they areimproperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint usage recommendations. Even with thistechnology, parents are STRONGLY encouraged to always properly restrain children in the rear seat...

the RCM also monitors the restraints warning light in the instrumentcluster. A difficulty with the system is indicated by one or more of thefollowing. • The warning light will either flash or stay lit. • The warning light will not illuminate immediately after ignition isturned on. • A series of five...

Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on theoutside shoulder only. Never wear the shoulder belt under the arm.2) Never swing the safety belt around your n...

Energy Management Feature — Outboard • This vehicle has a safety belt system with an energy managementfeature at the front seats to help further reduce the risk of injury inthe event of a head-on collision. • This safety belt system has a retractor assembly that is designed toextend the seat belt we...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning light andindicator chime remain off. BeltMinder 姟 The BeltMinder 娂 feature is a supplemental warning to the safety belt warning function. This feature provides additional...

If... Then... The driver’s and front passenger’ssafety belts are buckled before theignition switch is turned to the ONposition or less than 1-2 minuteshave elapsed since the ignitionswitch has been turned ON... The BeltMinder 娂 feature will not activate. The driver’s or front passenger’ssafety belt ...

Reasons given... Consider... “Belts areuncomfortable” We design our safety belts to enhance comfort. Ifyou are uncomfortable - try different positions forthe safety belt upper anchorage and seatbackwhich should be as upright as possible; this canimprove comfort. “I was in a hurry” Prime time for an ...

re-enable during the same ignition cycle if the occupant buckles andremains buckled for approximately 30 seconds. Confirmation is not givenfor the one time disable. Deactivating/activating the BeltMinder 姟 feature The driver and front passenger BeltMinder 娂 are deactivated/activated independently. W...

• This will disable the BeltMinder 娂 feature for that seating position if it is currently enabled. As confirmation, the restraint system warninglight will flash 4 times per second for 3 seconds. • This will enable the BeltMinder 娂 feature for that seating position if it is currently disabled. As con...

For proper care of soiled safety belts, refer to Interior in the Cleaning chapter. AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The instrument panel grab handle should never be used forstorage. The path of an inflating airbag must be kept clear at all times. The air bag supplemental restraint system ...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries. Airbags DO NOT inflate slowly; there isa risk of injury from a deploying airbag. Do not place any object between an occupant and an airbag or...

• Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to s...

Determining if the system is operational The supplemental restraint system uses a warning indicator in theinstrument cluster or a back-up tone to indicate the condition of thesystem. Refer to the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the air bag ...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

• diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and thesupplemental air bag electrical system wiring (including the impactsensors), the system wiring, the air bag system readiness light, the airbag back up power...

Side air bags, in combination with seat belts, can help reduce the risk ofsevere injuries in the event of a significant side impact collision. The side air bags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the air bag on the side affectedby the c...

Safety Canopy 姟 system (if equipped) Do not place objects ormount equipment on or near the headliner at the siderailthat may come into contact with adeploying Safety Canopy 娂 . Failure to follow these instructions mayincrease the risk of personal injuryin the event of a collision. Do not lean your h...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Air Bag Technical WorkingGroup. These recommended testingprocedures help reduce the ris...

The Safety Canopy 娂 is mounted to roof side-rail sheet metal, behind the headliner, along the entire side of the vehicle. In certain lateral collisionsor rollover events, the Safety Canopy 娂 system will be activated, regardless of which seats are occupied. The Safety Canopy 娂 is designed to inflate ...

• The readiness airbag light (same light as for front air bag system) willeither flash or stay lit. • The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and light are repai...

Children and safety belts If the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as specified by your child safetyseat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions tha...

• Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? Typ...

The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat...

Installing child safety seats with combination lap and shoulderbelts Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all theway back. Children 12 and ...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to...

Rear seating positions Follow Steps 1–7 as described above for the following available seats: • 2nd row bucket (40/40) • 2nd row bench (60/40) • 3rd row bench Note : The cargo tie-downs at the rear edge of the floor are nottether anchors. For additional important safety information on the proper use...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls for cuts, bruises and other damage. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case it needs to be repaired or replaced...

pressure should never be set lower than the recommended pressure onthe tire label or certification label. When weather temperature changes occur, tire inflation pressures alsochange. A 10° F (6° C) temperature drop can cause a correspondingdrop of 1 psi (7 kPa) in inflation pressure. Check your tire...

the road tires and wheels that were originally provided by Ford. If thedissimilar spare tire or wheel is damaged, it should be replaced ratherthan repaired. When driving with the dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time...

1. Remove the carpeted floor panellocated in the rear of the vehicle,remove the wing nut that securesthe spare tire by turning itcounterclockwise. 2. Lift and remove the spare tirefrom the trunk. 3. Remove the second wing nut thatsecures the jack retention bracketby turning it counterclockwise,remov...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Take care toposition the jack as shown to ensurethat the locating holes in the jackbase can be placed on the locatingtabs of the jack mounting brack...

If you are stowing the flat tire, remove the “L”-shaped bolt from thelarge wing nut used to secure thespare tire in the vehicle. With the3rd row seat in the raised position,stand the flat tire in the rear of thevehicle with the tire’s valve stemfacing the rear of the vehicle.Fasten the flat tire to ...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

the road in adverse (wet, snowy, etc.) conditions. Visually check yourtires for uneven wear, looking for high and low areas or unusuallysmooth areas. Also check for signs of tire damage. When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to prevent your vehiclefrom skiddin...

• Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five...

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln Mercury dealership to check for and correct any wheelmisalignment, tire imbalance or mechanical problem involved before tirerotation. Note: Your ...

• If possible, avoid fully loading your vehicle. • Remove the tire cables when they are no longer needed. Do not usetire cables on dry roads. • The suspension insulation and bumpers will help prevent vehicledamage. Do not remove these components from your vehicle whenusing snow tires and chains. • D...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door. Lookfor “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for m...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. 2005 Freestyle (219) Owners Guide (post-2002-fmt)USA_English (fus) Tires, Wheels and Loading 183

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

mandatory options, no cargo (internal or external), a tongue load of10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (150 lb. [68 kg]). Consult your dealership (or the RV and Trailer Towing Guide provided by your dealership) for more detailed informati...

capacity to carry you, 4 of your friends and all the golf bags? You andfour friends average 220 lb. (99 kg) each and the golf bags weighapproximately 30 lb. (13.5 kg) each. The calculation would be: 1400 –(5 x 220) – (5 x 30) = 1400 – 1100 – 150 = 150 lb. Yes, you haveenough load capacity in your ve...

Driving while you tow When towing a trailer: • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • It is recommended to select the L (Low) gear position when ad...

RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a recreational vehicle ormoving truck). In case of roadside emergency with a disabled vehicle, please refer to the Wrecker towing section in the Driving chapter...

STARTING Positions of the ignition 1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and all electricalaccessories off without locking thesteering wheel. To lock the steeringwheel, remove the key then turn thesteering wheel. 2. ACC, allow...

Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (START). 2. Turn the key to 4 (START), thenrelease the key as soon as theengine starts. Excessive crankingcould damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, ...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

is especially useful on slippery road surfaces. The system operates bydetecting and controlling wheel spin. The system borrows many of theelectronic elements already present in the anti-lock braking system(ABS). Wheel-speed sensors allow excess wheel spin to be detected by theTraction Control 娂 port...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this p...

Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normal detection zone of the RSS system may create false beeps. The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners o...

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. W...

turn the steering wheel only as rapidly and as far as required to avoidthe emergency). Excessive steering will result in less vehicle control,not more. Additionally, smooth variations of the accelerator and/orbrake pedal pressure should be utilized if changes in vehicle speed arecalled for. Avoid ab...

Mud and water If you must drive through high water, drive slowly. Traction or brakecapability may be limited. When driving through water, determine the depth; avoid water higherthan the bottom of the hubs (if possible) and proceed slowly. If theignition system gets wet, the vehicle may stall. Once t...

Make sure you allow sufficient distance between you and other vehiclesfor stopping. Drive slower than usual and consider using one of the lowergears. In emergency stopping situations, apply the brake steadily. Sinceyour vehicle is equipped with a four wheel anti-lock brake system (ABS),do not “pump”...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

The fuel pump shut-off switch islocated in the front passengerfootwell area in the right uppercorner. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a f...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — — — 30A Green Green Green Pin...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F18 10A PCM relay coil, Shifter Brake-ShiftInterlock (BSI), Passive Anti-Theft System(PATS) module, Fuel relay coil, Brakelamps, Center High-Mounted Stop Lamp(CHMSL) F19 10A Anti-lock Brake System (ABS)/Tractioncontrol ...

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your vehicle. A...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMot...

Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

concern have been unsatisfactory, Ford of Canada participates in animpartial third party mediation/arbitration program administered by theCanadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all oth...

Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide Fre...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint...

• 3.0L Duratec engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cleaning, use Motorcra...

Do not use sharp objects, such as a razor blade, to clean theinside of the rear window or to remove decals, as it may causedamage to the rear window defroster’s heated grid lines. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then with a clean, drycloth, or use Moto...

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaningthe seat-mounted side air bag. Such products could contaminate the side air bag system and affect performance of the ...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the style ...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provi...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood and support it withthe prop...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by aqualified service technician. 7. Put the indicator ...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to scheduled maintenance information for the servi...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (an opaque plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your dealer check the engine cooling system. Your coolingsystem may have a leak. Operating an engine with a low level of coolantcan result in engine overheating and possible engine damage. Recycled engine coolant For...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

with the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. “Premium”unleaded gasoline is not recommended f...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may n...

BRAKE FLUID RESERVOIR The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange ...

REFILL CAPACITIES Fluid Ford PartName Application Capacity Brake fluid MotorcraftHighPerformanceDOT 3 MotorVehicle BrakeFluid All Between MAXand MIN onreservoir Enginecoolant 1 MotorcraftPremium GoldEngine Coolant(yellow-colored) 3.0L engine 11.6 quarts(11.0L) Engine oil(includes filterchange) 2 Mot...

Items Ford PartName orequivalent Ford PartNumber FordSpecification Power TransferUnit Motorcraft SAE75W-90 FuelEfficient HighPerformanceRear AxleLubricant XY-75W-90–QFEHP — Engine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 SuperPremium MotorOil (Canada) XO-5W20-Q...

The vehicle identification number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake type and gross vehicleweight rating (GVWR) 3. Vehicle line, series, body type4. Engine type5. Check digit6. Model year7. Assembly plant8. Production sequence number Engine number The...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Accessory delay ..........................66 Air bag supplemental restraintsystem ................132–133, 139, 142 and child safety seats ............134description ..............133, 139, 142disposal ....................................145driver air bag ..........135, 140, 143indicator light ......

brake-shift interlock (BSI) ....198fluid, checking and adding(automatic) .............................266lubricant specifications ..........270 Turn signal ..................................56 V Vehicle dimensions ...................272Vehicle Identification Number(VIN) ................................