Ford 2005 Five Hundred v.3- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Check fuel cap: Illuminates when the fuel cap may not be properlyinstalled. Continued driving withthis light on may cause the Checkengine warning light to come on,refer to Fuel filler cap in the Maintenance and Specification chapter. Brake system warning light: To confirm the brake system warninglig...

Parking brake ON: Sounds when the parking brake is left ON and driven. If the warning stays on after the park brake is off, contact yourdealer as soon as possible. GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At norma...

AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED) 1. / Tuner: Press to manually go up or down the radiofrequency. Also use in menu modeto select various settings. 2. Phone/mute: Press to mute the playing media. Press again to returnto the playing media. 3. Menu: Press to toggle through the followin...

Balance: Press to adjust the audio between the left and right speakers. Use / / SEEK . Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and w...

Bass: Press to adjust the bass setting. Use / / SEEK . Treble: Press to adjust the treble setting. Use / / SEEK . Balance: Press to adjust the audio between the left and right speakers. Use / / , SEEK . Fade: Press to adjust the audio between the front and rear speakers. Use / / , SEEK . Occupancy m...

14. Seek: Press to access the previous strong station or track. 15. AM/FM: Press to select AM/FM frequency band. 16. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decreasevolume.If the volume is set above a certainlevel and the ignition is turned off,the volume will come back on at a“nominal...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theairflow selector in the O (OFF) or with recirculated air engaged. • Do not put objects under the front se...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED) 1. Defrost : Distributes outside air through the windshield defroster and demister vents. Can be used to clear ice or fog from the windshield. 2. Passenger temperature control: Press to increase/decrease the airflow temperature f...

OPERATING TIPS • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theairflow selector in the OFF or with recirculated air engaged. • Do not put objects under the front seats ...

REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel andworks to clear the rear window of fog and thin ice. The ignition must be in the 3 (RUN) position to operate the rear windowdefroster. The defroster turns off automatically after 10 minutes or when theigniti...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of theheadlamp...

1. Make sure the headlamp switch is in the OFF position and open thetrunk. 2. Carefully pull the carpet away to expose the backside of the tail lampassembly. 3. Remove the nut and washer assemblies, then pull the lamp assemblyaway from the vehicle. 4. Remove the bulb socket byrotating it countercloc...

Changing the wiper blades 1. Pull the wiper arm away from thevehicle. Turn the blade 90 degreesfrom the wiper arm and remove itfrom the arm. 2. Attach the new wiper to thewiper arm by turning it 90 degreesit into place. Replace wiper blades at least onceper year for optimum performance. Poor wiper q...

ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on thevisor mirror lamp. The visor willslide back and forth on the rod forincreased sunlight coverage. STORAGE COMPARTMENT Press the latch to open the storagecompartment. The door will openslightly and can be moved to fullopen. The storage compa...

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damage theoutlet and blow the fuse. Do not hang any type of accessory oraccessory bracket from the plug. Improper use of the poweroutlet can cause damage ...

Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (to the first detent) andhold the switch to close. One touch up or down This feature is present on the driver’s window only. To operate ONE TOUCH DOWN: • Press the swi...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press theright side of the control. Press theleft side to restore the windowcontrols. Bounce-Back (Driver’s window only) When an obstacle has been detecte...

MIRRORS Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mirrors in place...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control(located on the instrument panel) toadjust accelerator and brake pedal. • Press the top of...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or pressCNCL (Cancel). This will noterase your vehicle’s previously setspeed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set s...

In any mode: • Press VOL up or down to adjustthe volume. • Press MUTE to mute the volume. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up toventilate the vehicle. To open the moon roof: The moon roof is equipped with anautomatic, one-touch, expressopenin...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitterswith a single built-in device. This feature will learn the radio frequencycodes of most transmitters to opera...

Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLink 威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or otherrolling code equipped device), repeat...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status. Thesystem will a...

Warnings Status Low brake fluid Warning returns after the ignition keyis turned from OFF to RUN Liftgate ajar (if equipped) Trunk ajar (if equipped) Check Traction Control (ifequipped) Washer Fluid level low Coolant level low Check engine Change oil soon Oil change required Data error DRIVER’S DOOR ...

CENTER CONSOLE Your vehicle may be equipped with avariety of console features. Theseinclude: • Utility compartment with powerpoint • Gear Shift • Cup holders • Rear vent (if equipped) Use only soft cups in the cupholder. Hard objects can injure youin a collision. CELL PHONE USE The use of Mobile Com...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your dealer suppliedkeys, replacement keys are available throug...

1. Place the key in the ignition and turn the ignition to the 3 (RUN)position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn ...

Press to automatically move the seat, mirrors and adjustable pedals to the desired memory position (the positions correspond to the transmitterbeing used). For more information on programming the transmitters toDriver 1 and Driver 2 memory positions, refer to How to reprogram your remote entry trans...

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correc...

2. Put the key in the ignition. 3. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK)position and 3 (RUN). Note: The eighth turn must end in the 3 (RUN) position. 4. The doors will lock, then unlock, to confirm that the programmingmode has been activated. 5. Within 20 seconds press a...

• If the courtesy lamps were turned on because one of the vehicle doorswas opened, the battery saver will shut them off 10 minutes after theignition has been turned to the 1 (LOCK) position. • The battery saver will shut off the headlamps and foglamps 10minutes after the ignition has been turned to ...

2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be enteredwithin five seconds of each other. 4. To associate the entry code with a memory setting, enter a sixth digitto indicate which driver should be set in a memory recalled by thepersonal...

Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of eachother. The interior lamps will illuminate. To unlock all doors, enter the factory set code or your persona...

Power door unlock/lock procedure You must complete steps 1-5 within30 seconds or the procedure willhave to be repeated. If theprocedure needs to be repeated,you must wait 30 seconds. 1. Turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control three times. 3. Turn the ignitio...

Replacement keys If your keys are lost or stolen and you don’t have an extra coded key,you will need to have your vehicle towed to a dealership. The key codesneed to be erased from your vehicle and new coded keys will need to beprogrammed. Replacing coded keys can be very costly. Store an extra prog...

• Press the driver or passengerinterior door lock control whilethe door is open, then close thedoor. • Press the 7 • 8 and 9 • 0 controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdownwhen any of the above actions occurbefore t...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints Head ...

Using the manual lumbar support (if equipped) The lumbar support control islocated on the outboard side of theseatback. Move the control up or down toadjust lumbar support. Folding down the front passenger seatback (if equipped) The front passenger seatback can befolded to a horizontal position toma...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull onthe seatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a ...

• in any gearshift position if the ignition is not in the RUN position. • only in Park or Neutral if the ignition is in the RUN position. A memory seat position may be programmed at any time.The memory positions are also recalled when you press your remoteentry transmitter UNLOCK control if the tran...

SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and cra...

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints. The passenger occupant classification sensor can automatically turn offthe passenger front airbag. The system is designed to help protect small(child size) occupants from airbag dep...

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety belt pretensioners, front safety belt buckle sensors, driver seatposition sensor, and passenger occupant classification sensor. In addition,the RCM al...

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a seat belt. Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the...

All restraints in the vehicle are combination lap and shoulder belts. While you are fastened in the seat belt, the combination lap/shoulder beltadjusts to your movement. However, if you brake hard, turn hard, or ifyour vehicle receives an impact of 5 mph (8 km/h) or more, the safetybelt will become ...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch (20cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the s...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness light, the airbagback up power an...

If it is necessary to modify an advanced front airbag system toaccommodate a person with disabilities, contact the Ford CustomerRelationship Center at the phone number shown in the CustomerAssistance section of this Owners Guide. Any alteration/modification to the front passenger seat mayaffect the ...

The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected bythe collision will be inflated. If the front passenger sensing systemdetects an empty seat, the front passenger seat-mounted side airbag willbe deacti...

Safety Canopy 姟 system (if equipped) Do not place objects ormount equipment on or near the headliner at the siderailthat may come into contact with adeploying Safety Canopy 娂 . Failure to follow these instructions mayincrease the risk of personal injuryin the event of a collision. Do not lean your h...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

Any difficulty with the system is indicated by one or more of thefollowing: • The readiness airbag light (same light as for front airbag system) willeither flash or stay lit. • The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The...

Children and safety belts If the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as specified by your child safetyseat manufacturer) should always wear safety belts. Follow all the important safety restraint and airbag precautions that...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

Both can be used in any vehicle in a seating position equipped withlap/shoulder belts if your child is over 40 lb. (18 kg). The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up high across the stomach. I...

Installing child safety seats with combination lap and shoulderbelts airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the wayback. Children 12 and un...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to...

5. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat may not be retained properlyin the event of a collision. 6. Install the child safety seat tightly using the LATCH anchors or safetybelts. Follow the instructions in this chapter. 7. Tight...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear andremove stones, nails, glass or other objects that may be wedged in thetread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls...

Temporary spare tire information The temporary spare tire for your vehicle is labeled as such. It is smallerthan a regular tire and is designed for emergency use only. Replace thetemporary spare tire with a full-size tire as soon as possible. If you use the temporary spare tire continuously or do no...

Removing the spare tire and jack 1. Lift the trunk cargo cover, andremove the wing nut that securesthe spare tire by turning itcounterclockwise. 2. Lift and remove the spare tirefrom the trunk. 3. Remove the second wing nut thatsecures the jack retention bracketby turning it counterclockwise,remove ...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Take care toposition the jack as shown to ensurethat the locating holes in the jackbase can be placed on the locatingtabs of the jack mounting brack...

If you are stowing the temporaryspare tire, place the tire over the jack and secure it with the largewing nut. WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km)after any wheel disturbance (tire rotation, changing a flat tire, wheelremoval, etc.)...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h)...

11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label, which is located on the B-Pillar or the edge of thedriver’s door, for the correct tire pressure for your vehicle. 12. Treadwear, Traction and Tempe...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more ev...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln Mercury dealership to check ...

The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. If you need to use snow tires and chains, it isrecommended that steel wheels are used of the same size andspecifications as those originally ins...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or ...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. 2005 Five Hundred (500) Owners Guide (post-2002-fmt)USA (fus) Tires, Wheels and Loading 157

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

The following gives you a few examples on how to calculate the availableamount of cargo and luggage load capacity: • Another example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You decide to go golfing. Is there enough loadcapacity to carry you, 4 of your friends and all th...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourdealer or trailer rental agency for proper instructions and equipment forhooking up trailer lamps. Driving while you tow When towing a trail...

RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a recreational vehicle ormoving truck). In case of roadside emergency with a disabled vehicle, please refer to the Wrecker towing section in the Driving chapter...

STARTING Positions of the ignition 1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and all electricalaccessories off without locking thesteering wheel. To lock the steeringwheel, remove the key then turn thesteering wheel. 2. ACC, allow...

Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (START). 2. Turn the key to 4 (START), thenrelease the key as soon as theengine starts. Excessive crankingcould damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, ...

BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-outand should be inspected by a qualified service technician. If the vehiclehas continuous vibration or shudder in the steering wheel while braking,th...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

TRACTION CONTROL 姟 (IF EQUIPPED) Your vehicle may be equipped with a Traction Control 娂 system. This system helps you maintain the stability and steerability of your vehicle. Itis especially useful on slippery road surfaces. The system operates bydetecting and controlling wheel spin. The system borr...

To help avoid personal injury, always use caution when in R(Reverse) and when using the RSS. This system is not designed to prevent contact with small ormoving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damagingthe vehicle...

The RSS automatically turns onwhen the gear selector is placed inR (Reverse) and the ignition is ON.An RSS control on the instrumentpanel allows the driver to turn theRSS on and off. To turn the RSS off,the ignition must be ON, and the gear selector in R (Reverse). Anindicator light on the control w...

AWD Systems (if equipped) AWD uses all four wheels to powerthe vehicle. This increases traction,enabling you to drive over terrainand road conditions that aconventional two-wheel drive vehiclecannot. Sand When driving over sand, try to keep all four wheels on the most solidarea of the trail. Avoid r...

when you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until you regain control of the vehicle. If the transmission, AWD system components or axles are submerged inwater, their fluids should be checked...

Maintenance and Modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

The fuel pump shut-off switch islocated in the front passengerfootwell area in the right uppercorner. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a f...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — — — 30A Green Green Green Pin...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F17 30A Rear defroster F18 10A PCM relay coil, Shifter Brake-ShiftInterlock (BSI), PassiveAnti-Theft System (PATS)module, Fuel relay coil, Brakelamps, Center High-Mounted StopLamp (CHMSL) F19 10A Anti-lock Brake System(...

To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter. The high-current ...

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your vehicle. A...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

• available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedures and/or to discontinue this service without notice and withoutincu...

before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be requested by the Board as well. Making a decision Board members review all available information related to eachcomplaint, including oral presentation...

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings. In the CAMVAP program,...

Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing toFord ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint...

• 3.0L Duratec engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cleaning, use Motorcra...

Do not use sharp objects, such as a razor blade, to clean theinside of the rear window or to remove decals, as it may causedamage to the rear window defroster’s heated grid lines. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then with a clean, drycloth, or use Moto...

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaningthe seat-mounted side air bag. Such products could contaminate the side air bag system and affect performance of the ...

Motorcraft Car Wash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provi...

Working with the engine on 1. Set the parking brake and ensure the gearshift is securely latched in P(Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE ...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by aqualified service technician. 7. Put the indicator ...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to scheduled maintenance information for the servi...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (an opaque plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your dealer check the engine cooling system. Your coolingsystem may have a leak. Operating an engine with a low level of coolantcan result in engine overheating and possible engine damage. Recycled engine coolant For...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage. Fuel quality If you are experiencing star...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may n...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...

REFILL CAPACITIES Fluid Ford PartName Application Capacity Brake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid All Between MAXand MIN onreservoir Enginecoolant 1 MotorcraftPremium GoldEngine Coolant(yellow-colored) 3.0L engine 11.6 quarts(11.0L) Engine oil(includes filterchange) 2 Mo...

Items Ford PartName orequivalent Ford PartNumber FordSpecification Coupler fluid VolvoTransmissionOil, Clutch 1161641 — Power TransferUnit Motorcraft SAE75W-90 FuelEfficient HighPerformanceRear AxleLubricant XY-75W-90–QFEHP — Engine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcr...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehiclethrough your local authorized Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to co...

A Accessory delay ..........................48 Air cleaner filter .......................245 Air conditioning ....................27, 29 Airbag supplemental restraintsystem ........................109, 116, 119 and child safety seats ............111description ..............109, 116, 119disposal ......

fluid, checking and adding(automatic) .....................242–243lubricant specifications ..........248 Trunk ...........................................73 remote release ....................71, 76 Turn signal ..................................37 V Vehicle dimensions ...................250 Vehicle ...