Ford 2005 F-550 v.2- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

Using your vehicle with a snowplow For more information and guidelines for using your vehicle with asnowplow, refer to the Driving chapter. Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance PreparationPackage, it may be utilized as an ambulance. Ford urges am...

Using your vehicle as a stationary power source (PTO) Refer to the Driving chapter for more information and guidelines for operating a vehicle equipped with an aftermarket power take-off system. Middle East/North Africa vehicle specific information For your particular global region, your vehicle may...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Standard instrument cluster (manual transmission) Standard instrument cluster (automatic transmission) Harley—Davidson instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light...

Many lights will illuminate when you start your vehicle to make sure thebulbs work. If any light remains on after starting the vehicle, have therespective system inspected immediately. If your vehicle is equipped with a Diesel engine, it has a unique cluster,refer to Starting the engine in your 6.0 ...

Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehiclechecked by your dealer immediately. Anti-lock brake system: If the ABS light stays illuminated orcontinues to fl...

Four wheel drive low: Illuminates when four-wheel drive low isengaged. Four wheel drive indicator: Illuminates when four-wheel drive isengaged. Speed control: Illuminates when the speed control is activated. Turnsoff when the speed control systemis deactivated. Turn signal: Illuminates when the left...

GAUGES Speedometer: Indicates the current vehicle speed. Standard instrument cluster Harley—Davidson instrumentcluster Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the r...

Tachometer: Indicates the engine speed in revolutions per minute.Driving with your tachometerpointer continuously at the top ofthe scale may damage the engine. Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the ne...

Transmission fluid temperature gauge (automatic transmissiononly): If the gauge is in the: Normal area (normal) - the transmission fluid is within thenormal operating temperature(between “H” and “C”). Yellow area (warning) — the transmission fluid is higher thannormal operating temperature. Thiscan ...

AM/FM STEREO SYSTEM (IF EQUIPPED) 1. / Tuner: Press to manually go up or down the radiofrequency. Also use in menu modeto select various settings. 2. Audio: Press to access select various settings. Treble: Press to adjust the treble setting. Use / / SEEK, SEEK . Bass: Press to adjust the bass settin...

Balance: Press to adjust the audio between the left and right speakers. Use / / SEEK . Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and w...

17. LOAD: Press to load a CD, then select a slot number using the radiopresets 1 through 6. If you don’tselect a slot within 5 seconds, theradio shall choose the first availableslot for you. Press and hold for 2 seconds to auto load up to six CDs. 18. CD eject: Press to eject a CD, then select the d...

• Allow tapes which have been subjected to extreme heat, humidity orcold to reach a moderate temperature before playing. • Clean the cassette player head with a cassette cleaning cartridge after10–12 hours of play to maintain good sound/operation. Don’t: • Expose tapes to direct sunlight, extreme hu...

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brie...

: Distributes outside air through the instrument panel vents, floor vents and center console vents (if equipped). O (OFF): Outside air is shut out and the climate system is turned off. : Distributes outside air through the floor vents. : Distributes outside air through the windshield defroster vents...

AUTOMATIC TEMPERATURE CONTROL SYSTEM (IF EQUIPPED) Press the AUTO and (floor/defrost) controls at the same time and hold for one second to switch between Fahrenheit and Celsius. 1. A/C: Press to activate/deactivate air conditioning. Use withrecirculated air to improve coolingperformance and efficien...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

Vertical and horizontal aim adjustment (sealed beam headlamps) The headlamps on your vehicle are intended to be aimed usingmechanical aimers. If mechanical aimers are used and the cross-car sightline is in any way blocked, set the legs of the universal adaptor all to thesame setting, such that the c...

3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. Cover one of the headlamps so no light hits the wall. 4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge towards theright. If this edge is not at thehorizontal reference line, th...

Replacing tail lamp/turn/backup lamp bulbs — F250/F350 only 1. Make sure the headlamp switch isin the OFF position and then openthe tailgate to expose the lampassemblies. 2. Remove the two bolts from thetail lamp assembly and carefully pullthe lamp assembly from the tailgatepillar by releasing the t...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

TILT STEERING WHEEL (IF EQUIPPED) To adjust the steering wheel: 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Release the steering wheelrelease control. This will lock thesteering wheel in position. Never ad...

To vent the moon roof: Press and hold the control. The moon roof must be in the closed position in order to move it into thevent position. To close, press and hold the AUTO control until the glass panel stops moving. The moon roof has a built-in sliding shade that can be manually openedor closed whe...

When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and hold the bottom part ofthe rocker switch to open thewindow. Press and hold the top partof the rocker switch to close thewindo...

Accessory delay (if equipped) With accessory delay, the window switches may be used for up to tenminutes after the ignition switch is turned to the OFF position or untilany door is opened. MIRRORS Automatic dimming inside rear view mirror (if equipped) Your vehicle is equipped with an inside rear vi...

Heated outside mirrors (if equipped) The main mirror glass is heated automatically to remove ice, mist andfog and activates when the vehicle is started. Note: The mirrors may be hot to the touch but will not burn. This is a normal condition. Type A The mirror heating elements aredesigned to operate ...

STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate controlfeatures. Radio control features • Press MODE to select AM, FM1,FM2, TAPE or CD (if equipped). In Radio mode: • Press NEXT to seek/scan to thenext strong station. In Tape mode: • Press NEXT to lis...

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment withcassette/CD holder • Coin holder • Pen holder • Writing surface Use only soft cups in thecupholder. Hard objects can injure you in a collision. CELL PHONE USE The use...

Check trailer (if equipped): Displayed when a trailer connectionbecomes disconnected, eitherintentionally or unintentionally, andhas been sensed during a givenignition cycle. Refer to Integrated trailer brake controller in the Tires, Wheels and Loading chapter for more information. Language The lang...

Selectable features Reset Press this control to select and resetfunctions shown in the INFO menuand SETUP menu. Info menu This control displays the followingcontrol displays: • Odometer/Compass • Trip odometer/Odometer/Compass • Distance toEmpty/Odometer/Compass • Average FuelEconomy/Odometer/Compas...

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegrees between adjacent zones and will become noticeable as thevehicle crosses multiple zones. A correct zone setting will eliminate thiserror. Refer to ...

7. Press the RESET control to startthe compass calibration function. 8. Slowly drive the vehicle in acircle (less than 3 mph [5 km/h])until the CIRCLE SLOWLY TOCALIBRATE display changes to CALIBRATION COMPLETED. It will takeup to five circles to complete calibration. 9. The compass is now calibrated...

This acts as a reminder that these warning conditions still exist withinthe vehicle. Warning display Status Reduced engine power Warning cannot be reset Stop engine safely Low fuel level Warning returns after 10 minutes Low brake fluid level Low oil pressure Check engine temperature Trailer disconne...

Tailgate removal Your tailgate is removable to allowmore room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry thespring clip (on each connector) pastthe head of the support screw.Disconnect cable. 3. Disconnect the other cable. 4. Lift tailgate to a 45–degree angle. 5. Lift right sid...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your dealer suppliedkeys, replac...

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correc...

To program the keyless entrykeypads remote entry transmittersyourself: 1. Ensure the vehicle iselectronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 2 (LOCK)position to 3 (OFF). 4. Cycle eight times rapidly (within10 seconds) between the 3 (OFF)position and 4 (ON). Note: ...

Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personalcode. • If you set a second personal code it will erase your first personal code. Erasing personal code 1. Enter the fact...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Head restraints The purpose of t...

Captain’s chair (if equipped) • Lift the bar to move the seatforward or rearward. Make surethat the seat is relatched intoplace. • To recline the seatback, pull therelease lever handle located onthe side of the seat up. • Push down the lever (ifequipped) located at the bottomof the seatback to quick...

Using the manual lumbar support For more lumbar support, turn thelumbar support control toward thefront of vehicle. For less lumbar support, turn thelumbar support control toward therear of vehicle. Heated seats (if equipped) To operate the heated seats, do the following: • Push control to activate....

REAR FOLDING SEAT SYSTEM WITH LOAD FLOOR (IF EQUIPPED) The rear seatback has a split 60/40 seat. Each seat cushion can beflipped up into the seatback position. 1. Pull down the latch lever locatedon the bottom seat back to fold theseat back forward. 2. Pull up on the lever located onthe side of the ...

To gain access to the cupholdersand tray, pull down on the armrest. To gain access to the 60/40 loadfloor, store the cushion in theupright locked position. Pull up onthe straps located at the sides of theload floor, and rotate forward untilresting on the carpet. SAFETY RESTRAINTS Safety restraints p...

It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people toride in any area of your vehicle that is not equipped with seats andsafety belts. Be sure everyone i...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The front outboard and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front outboard passenger andrear seat outboard safety belts have two types of locking modesdescribed below: Ve...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checkedaccording to the procedures in the Workshop Manual . Failure to replace the belt and retractor assembly could increase the...

• 4–door Super Cab To adjust the shoulder belt height, push the button and slide the heightadjuster up or down. Release the button and pull down on the heightadjuster to make sure it is locked in place. Position the safety belt height adjusters so that the belt restsacross the middle of your shoulde...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety ...

1. Turn the ignition switch to the RUN (or ON) position. (DO NOTSTART THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1minute) • Step 3 must be completed within 60 seconds after the safety beltwarning light turns off. 3. At a moderate speed, buckle then unbuckle the...

Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front seat belt buckleassem...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries. Airbags DO NOT inflate slowly; there isa risk of injury from a deploying airbag. All occupants of the vehicle, including the driver, should a...

Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford or Lincoln/Mercury dealer. The front passenger air bag is not designed to offer protection toan occupant in the center front seating position. Modifying or adding equipment to the front...

How does the air bag supplemental restraint system work? The air bag SRS is designed toactivate when the vehicle sustainssufficient longitudinal deceleration.The fact that the air bags did notinflate in a collision does not meanthat something is wrong with thesystem. Rather, it means the forceswere ...

If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS consists of: • driver and passenger air bag modules (which include the inflators andair bags)...

The vast majority of drivers and passengers are much safer with an airbag than without. To do their job and reduce the risk of life threateninginjuries, air bags must open with great force, and this force can pose apotentially deadly risk in some situations, particularly when a front seatoccupant is...

• makes the potential harm from the passenger air bag in a crashgreater than the potential harm from turning OFF the air bag andallowing the passenger, even if belted, to hit the dashboard orwindshield in a crash. This vehicle has special energy management safety belts for thedriver and right front ...

3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a special risk for the passenger if the air bag deploys; and • makes the potential harm from the passenger air bag deploymentgreater than the potential harm from turning OFF the air bag andexpe...

Always follow the instructions and warnings that come with any infant orchild restraint you might use. Children and safety belts If the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as specified by your child safetyseat manufacturer)...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

Both can be used in any vehicle in a seating position equipped withlap/shoulder belts if your child is over 40 lb. (18 kg). The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up high across the stomach. I...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly tilt the seat forwardand back to make...

The SuperCab rear seat has three straps behind the top of the seat backthat function as both routing loops for the tether straps and anchorloops. The tether strap anchors in your vehicle are in the following positions(shown from top view): Attach the tether strap only to the appropriate tether ancho...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information on shiftingprocedures and maintenance can befound in your Owner’s Guide . You should become thoroughly familiarwith this information befor...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, theycannot be treated like normal light truck tires. Tire service, includingadjusting tire pressure, must be performed by personnel trained,supervised and eq...

Only use replacement tires and wheels that are the same sizeand type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. Use of any tire orwheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in ...

The usage of a dissimilar spare tire/wheel can lead to impairment of thefollowing: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applica...

3. Fully insert the jack handlethrough the bumper hole and intothe guide tube. The key and lockwill engage with a slight push andcounterclockwise turn. Someresistance will be felt when turningthe jack handle assembly. 4. Turn the handle counterclockwiseand lower the spare tire until youcan slide the...

3. Remove the jack, jack handle, lug wrench and spare tire from thestowage locations. 4. Use the tip of the lug wrench to remove any wheel trim. 5. Loosen each wheel lug nut one-half turn counterclockwise but do notremove them until the wheel is raised off the ground. When one of the rear wheels is ...

Never use the front or reardifferential as a jacking point. To lessen the risk ofpersonal injury, do not put any part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle is on the jack. The jack isonly meant for changing the tire. 8. Turn the jack handle cloc...

• Front: F–450/F–550 • Rear: F-450/F-550 14. Insert the jack handle into thepump linkage. 15. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground. Hydraulic jacks are equippedwith a pressure release valvethat prevents lifting loads whichexceed the jack’s rated c...

The following steps apply to all vehicles: 19. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nuttorque specification. 8–lug nut torque sequence 10–lug nut torque sequence 20. Stow the flat tire. ...

Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing in the directionspecified on the Tire Changing Instructions located with the jackhardware. 2. Slide the w...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in thescheduled maintenance information that comes with your vehicle) willhelp your tires wear more even...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All—Wheel Drive (AWD)vehicles (front tires at top ofdiagram) • DRW – Six tire rotation If your vehicle is equipped with dualrear wheels it is recommended thatfront and rear tires (in pairs) berotated only side to side, with therear tires maintai...

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a reputable repair facility to check for and correct any wheel misalignment,tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle ...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door. Lookfor “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for m...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. 2005 F250/350/450/550 (f23) Owners Guide (post-2002-fmt)USA_English (fus) Tires, Wheels and Loading...

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

Special loading instructions for owners of pickup trucks andutility-type vehicles For important information regarding safe operation of this typeof vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this owner guide. Loaded vehicles may handle differently than unloade...

components carefully prior to and after any towing operation. Refer to Transmission temperature gauge in the Instrument Cluster chapter for the transmission fluid temperature information. The following trailer towing charts apply to vehicles equipped withgasoline engines; for vehicles equipped with ...

Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to theaxle. You must distribute the load in your trailer so that 10%–15% forconventional towing or 15%-25% fifth-wheel towing of the total weight ofthe trailer is on the tongue. Integrated hitch rating The standard integrated ...

Towing trailers beyond the maximum tongue weight exceeds thelimit of the towing system and could result in vehicle structural damage, loss of vehicle control and personal injury. Load equalizing hitch When hooking up a trailer using a load equalizing hitch, always use thefollowing procedure:1. Park ...

The braking system of the tow vehicle is rated for operation at theGVWR not GCWR. Integrated trailer brake controller (if equipped) Your vehicle may be equipped with a fully integrated electronic TrailerBrake Controller (TBC). When used properly, the TBC helps assuresmooth and effective trailer brak...

3. GAIN setting display: Shows the current GAIN setting. This will illuminate when a trailer is connected, flash if the trailer becomesdisconnected, or remain off if no trailer is connected. 4. OUTPUT bar graph: When the vehicle’s brake pedal is pushed, or when the manual control is activated, green...

5. In a traffic-free environment, tow the trailer on a dry, level surface ata speed of 20 – 25 mph (30 – 40 km/h) and squeeze the manual controllever completely. 6. If the trailer wheels lock-up (indicated by squealing tires), reduce theGAIN setting; if the trailer wheels turn freely, increase the G...

Points to Remember: • Remember to adjust gain setting before using the TBC for the firsttime. • Readjust GAIN setting on the TBC (according to procedure above)whenever road, weather and trailer or vehicle loading conditionschange from those that existed when the gain was initially set. • The sliding...

Driving while you tow When towing a trailer: • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive transmission shifting, activate the To...

Loading • Keep the center-of-gravity low for best handling. • Trailer loads should be evenly distributed front to back and left toright. • The load distribution within the trailer should be such that 10% – 15%of the trailer weight is on the hitch. (15% – 25% for 5th-wheel orgooseneck towing.) • Neve...

• Disconnect the trailer tow electrical connector to prevent blown fusescaused by water entering into your trailer’s electrical wiring. Exceeding these limits may allow water to enter critical vehiclecomponents, adversely affecting driveability, emissions and reliability. Replace front and rear axle...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. Forvehicles equipped with a manualtransmission, you must depre...

Extended idling at high engine speeds can produce very hightemperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the engine compartment and exhaust system,...

If starting a vehicle with an automatic transmission: 1. Make sure the parking brake isset. 2. Make sure the gearshift is in P(Park). If starting a vehicle with a manualtransmission: 1. Make sure the parking brake isset. 2. Push the clutch pedal to the floor. • Turn the key to 4 (ON) withoutturning ...

Starting the engine 1. Turn the key to 4 (ON) withoutturning the key to 5 (START). 2. Turn the key to 5 (START), thenrelease the key as soon as theengine starts. Excessive crankingcould damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to 3 (OF...

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If ...

Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake systemserviced immediately.) Using ABS When hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since thi...

Pull the right side of the releaselever to release the parking brake;the release lever pulls at an angletoward the driver’s door. To preventthe pedal from releasing too quickly,place your left foot on the parkingbrake pedal, then pull the releaselever, making sure the pedal fullyreleases. You may wa...

If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment If any steering components are serviced or replaced, install newfasteners (many are coated with thread...

Loaded vehicles, with a higher center of gravity, may handledifferently than unloaded vehicles. Extra precautions such as slower speeds and increased stopping distance should be taken whendriving a heavily loaded vehicle. AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehi...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transmission has a starter interlock that prevents crankingthe engine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then pu...

Shift according to the following shift speed charts: Upshifts when accelerating (recommended for best fuel economy) 6-speed transmission Shift from: Transfer case position 1 (if equipped) 2H or 4H 4L LO-1 5 mph (8 km/h) 2 mph (3 km/h) 1-2 15 mph (24 km/h) 6 mph (10 km/h) 2-3 22 mph (35 km/h) 9 mph (...

Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Fully apply the parking brake, then shift into 1 (First). 3. Turn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Rem...

This system is not designed to prevent contact with small ormoving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damagingthe vehicle. The system may not detect smaller objects, particularlythose close to the ground. Certain a...

4. Move the transfer case shift leverthrough N (Neutral) directly to 4L(4WD Low). 5. If the transfer case will not engage into 4L (4WD Low), let thevehicle creep at a speed above 1mph (1.6 km/h), then repeat steps 1through 4. Shifting from 4L (4WD Low) to 4H (4WD High) or 2H (2WD High) 1. Bring the ...

Do not leave the vehicle unattended with the transfer case in theN (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Using the electronic shift 4WD system (if equipped) Positions of the electronic shift system The electronic shift 4WD system i...

Shifting from 4x4 HIGH (4WD High) to 2WD (2WD High) Rotate the 4WD control to 2WD atany forward speed. Disengagementof the transfer case and front hubsmay be delayed due to torque bindwhich is caused by driving on dryhard surfaces or performing tightturns while using the 4WD system. • You do not nee...

4. Move the 4WD control to the 4x4HIGH (4WD High) or 2WD (2WDHigh) position. 5. Hold the shift conditions until theLOW RANGE indicator light shutsoff. 6. If the LOW RANGE indicator light does not shut off within 15 seconds, drive the vehicle above 5mph (8 km/h), then repeat steps 1through 5 before r...

• Be extremely careful when driving on pavement made slippery byloose sand, water, gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ease the vehicle back onto thepavement only aft...

Refer to Transmission temperature gauge in the Instrument Cluster chapter for transmission fluid temperature information. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,turn the steering wheel onl...

be required from another vehicle. Remember, you may be able to backout the way you came if you proceed with caution. Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills . A danger lies in losing traction, sli...

traction or brake capability may be limited. Also, water may enter yourengine’s air intake and severely damage your engine or your vehicle maystall. Driving through deep water where the transmission vent tube is submerged may allow water into the transmission andcause internal transmission damage. O...

pressure for the tire and associated load rating is imprinted on the tiresidewall. Tire air pressure may require re-adjustment within thesepressure limits to accommodate the additional weight of the snowplowinstallation. • Federal and some local regulations require additional exterior lampsfor snowp...

Do not attempt to service, repair, or modify the air bagsupplemental restraint system (SRS) or its fuses. See your Ford or Lincoln Mercury dealer. Additional equipment such as snowplow equipment may effectthe performance of the air bag sensors increasing the risk of injury. Please refer to the Body ...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a few seconds...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 304 — Not used 305 Full ISO relay Upfitter control 306 Full ISO relay Delayed accessory 307 Full ISO relay Starter 601 30A circuit breaker Delayed accessory, Powerwindows, Moonroof 602 — Not used * Mini fuse ** Cartridg...

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your vehicle. A...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheelson the ground and the rear wheels ...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMot...

Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln/Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln/Mercury deale...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

concern have been unsatisfactory, Ford of Canada participates in animpartial third party mediation/arbitration program administered by theCanadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all oth...

Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide Fre...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

• Cover the highlighted areas to prevent water damage when cleaningthe engine. • 5.4L V8 gasoline engine • 6.8L V10 gasoline engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cleaning, use Motorc...

• If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. ...

INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area firstwith Mo...

Regular cleaning and conditioning will maintain the appearance of theleather. Failure to care for the leather can result in drying out and fadingof the material. Cleaning For dirt, use a vacuum cleaner then use a clean, damp cloth or softbrush. First use a damp cloth then wipe with a dry cloth. Allo...

UNDERBODY Flush the complete underside of your vehicle frequently. Keep body anddoor drain holes free from packed dirt. Note: Use care when using a power washer to clean the driveline, especially the driveshaft and interfacing components. The high-pressurefluid could penetrate the sealed parts and c...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provideth...

• Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease h...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L V8 gasoline engines Refer to the 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 1. Transmission fluid dipstick (automatic transmission) 2. Air filter assembly 3. Engine coolant...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range. • Oil levels above the M...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the Scheduled Maintenance Guide for the service...

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery,always shield your face and protect your eyes. Always provide properventilation. When lifting a plastic-case...

• The vehicle may need to be driven 10 miles (16 km) or more torelearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. If the battery has been disconnecte...

• 5.4L/6.8L When the engine is cold, check the level of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to the Scheduled Maintenance Guide for ser...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant. To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant ...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section....

4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Re-start the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehi...

Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel container whilefill...

Many of the world’s automakers approved the World-wide Fuel Charterthat recommends gasoline specifications to provide improvedperformance and emission control system protection for your vehicle.Gasolines that meet the World-wide Fuel Charter should be used whenavailable. Ask your fuel supplier about...

Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter. The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated ca...

5. Follow one of the simple calculations in order to determine fueleconomy: Calculation 1: Divide total miles traveled by total gallons used. Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled. Keep a record for at least one month and record the type of driving (cit...

Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended engine oil. Refer to Lubricant specifications in this chapter. • Perform all regularly scheduled maintenance items. Follow there...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

engine must warm up to its normal operating temperature. Once started,do not turn off the engine until the above driving cycle is complete. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If adding flu...

BRAKE FLUID RESERVOIR The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange ...

1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir. 2. Remove cap and rubberdiaphragm from reservoir. 3. Add fluid until the level reachesthe step in the reservoir. 4. Reinstall rubber diaphragm andcap onto reservoir. TRANSMISSION FLUID Checking automatic t...

If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician. An overfill condition oftransmission fluid may cause shift and/or engagement concernsand/or possible damage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials m...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at thebottom of the opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. I...

Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to Lubr...

AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter. Note: Do not start your engine ...

REFILL CAPACITIES Fluid Ford Part Name Application Capacity Front axle Motorcraft SAE80W-90Premium RearAxle Lubricant F-250/350(Dana 60 axle) 6.3 pints (3.0L) F-350/450/550(Dana 60 axle) 6.3 pints (3.0L) Rear axle Motorcraft SAE75W-140Synthetic RearAxle Lubricant F-250 /350(10.50 inchaxle) 1 6.9 pin...

6 Use of synthetic or synthetic blend motor oil is not mandatory. Engine oil need only meet the requirements of Ford specificationWSS-M2C930-A and the API Certification mark. LUBRICANT SPECIFICATIONS Item Ford partname orequivalent Ford partnumber Fordspecification Spindle bearing HighTemperature4X4...

Item Ford partname orequivalent Ford partnumber Fordspecification Engine coolant MotorcraftPremium GoldEngine Coolant(yellow-colored) VC-7-A (U.S.,except CA, ORand NM),VC-7-B (CA, ORand NM) WSS-M97B51-A1 Engine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 SuperPrem...

ENGINE DATA Engine 5.4L V8 engine 6.8L V10 engine Cubic inches 330 415 Required fuel 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9 Spark plug gap 1.02–1.28mm(0.040–0.050 inch)** 1.02–1.28mm(0.040–0.050 inch)** Ignition system Coil on plug Coil on plug Compression ratio 9.8:1 ...

1. World manufacturer identifier 2. Brake type and gross vehicleweight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identificationnum...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Accessory delay ..........................59 Air bag supplemental restraintsystem ................................107–108 and child safety seats ............109description ..............................108disposal ....................................111driver air bag ..........................110i...

dipstick ....................................251filter, specifications ........254, 282recommendations ...................254refill capacities ........................283specifications ..................286, 289 Exhaust fumes ..........................183 F Fail safe coolant ...........................

Power steering ..........................185 fluid, checking and adding ....273fluid, refill capacity ................283fluid, specifications .........286, 289 Power Windows ...........................57 Preparing to drive yourvehicle ........................................186 R Radio ...............