Ford 2005 Expedition v.2- User Manual

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

Service engine soon: The Service engine soon indicator light illuminates when the ignition is firstturned to the ON position to checkthe bulb. Solid illumination after the engine is started indicates the OnBoard Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (O...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately. Normalbraking is still functional unless the brake warning light also isilluminated. Air bag readiness: If this light fails to illuminate when ignitio...

Low fuel (if equipped): Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in this chapter). Check fuel cap (if equipped): Illuminates when the fuel cap maynot be properly installed. Continueddriving with this light on may causethe Service engine soon warningligh...

Four wheel drive low (ifequipped): Illuminates when four-wheel drive low is engaged. Ifthe light fails to illuminate when theignition is turned ON, continues to flash or remains on, have the systemserviced immediately. Four wheel drive high (ifequipped): Illuminates when four-wheel drive is engaged....

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, theengine is overheating. Stop thevehicle as soon ...

• With Full Message Center Refer to Message Center in theDrivers Controls chapter on how toswitch the display from Metric toEnglish. Trip odometer: Registers the miles (kilometers) of individual journeys. • With Mini Message Center Press the SELECT/RESET controlonce to switch from the odometer tothe...

Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls below thenormal range, stop the vehicle, turnoff the engine and check the engineoil level. Add oil if needed. If the oillevel is correct, have your v...

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED) 1. EJ (Eject): Press to stop and eject a tape. 2. EJ (Eject): Press to stop and eject a CD. 3. BASS: Allows you to increase or decrease the audio system’s bassoutput. Press BASS then press SELto decrease or increase the bass levels. TREB (Treble)...

In CD mode, REW control reverses the CD within the current track. FF (Fast Forward): Works in tape and CD modes. In the tape mode, tape directionautomatically reverses when the end of the tape is reached. In CD mode, FF advances the CD within the current track. 10. MUTE: Press to mute the playing me...

11. AUTOSET: Press to set first six strong stations into AM, FM1 orFM2 memory buttons; press again toreturn to the original presetstations. If there are less than six strong stations available on thefrequency band, the remaining memory preset controls will all store thelast strong station available....

Treble: Press TREB; then press SEL / to decrease/increase the treble output. 7. Select: Use with Bass, Treble, Balance and Fade controls to adjustlevels and set the clock. 8. Balance: Press BAL; then press SEL / to shift sound to the right/left speakers. Fade: Press FADE; then press SEL / to shift s...

Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise.Recommended level is 1–3. Level 0 turns the feature off and level 7 isthe maximum setting.Press and hold the volume control for five seconds. Then press SEL toincrease ( )...

TREB (Treble): Allows you to increase or decrease the audiosystem’s treble output. Press TREBthen press TEXT/SEL todecrease or increase the treble levels. 4. BAL (Balance): Allows you to shift speaker sound between theright and left speakers. Press BALthen press TEXT/SEL to shift soundto the left or...

Traffic (if equipped): Allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a trafficreport (if it is broadcasting RDS data). Traffic information is not available in most U.S. markets. FIND Program type (if equipped): Allows you to search RDS-...

10. REPEAT: Press to repeat the current CD/MP3 track. 11. SHUFFLE: Press play the CD/MP3 tracks on the current discin random order. 12. FOLDER : Press to access the next MP3 directory. 13. FOLDER : Press to access the previous MP3 directory 14. FF (Fast forward): In CD mode, press until desired sele...

20. Load: Press to load a CD. Press and hold to load up to six discs. 21. CD: Press to enter CD mode. CD units are designed to play commercially pressed 4.75 in (12cm) audio compact discs only. Due to technical incompatibility,certain recordable and re-recordable compact discs may notfunction correc...

To activate Dual Play mode (rearseat passengers listen to a differentplaying media than the front seatpassengers): • Press the speaker/headphonecontrol. • Press the MODE control tochange audio sources (forheadphone mode only) • Use the SEEK, VOLUME andMEMORY/MEM controls to make adjustments to the p...

Turning the rear speakers on and off Press the headphone/speakercontrol to turn the rear speakers on(Single Play mode) or off (Dual Playmode). Using headphones/Dual Play mode Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. DUAL PLAYil...

Memory preset control Push the MEMORY/MEM controlsuccessively to allow rear seatpassengers to scroll through the 6memory presets in AM, FM1 orFM2. Push the MEMORY/MEM control inCD mode (if equipped) to advanceto the next disc. Seek function • In radio mode, press to find the next listenable station ...

RADIO FREQUENCIES AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz RADIO RECEPTION FACTORS There are three factors th...

Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12cm) audio compact discs only. Due to technical i...

7. Auxiliary jacks Insert lines for standard video game players. 8. STOP/EJECT control Press once to stop DVD play. Press again to eject the DVD. 9. DISPLAY (DISP) control Press to enable on screen display of player menu and user displayadjustments. DVD control features Menu control Press the MENU c...

8. VOLUME control Press to increase (+) or decrease (-) volume level. Battery replacement Batteries are supplied with theremote control unit. Since allbatteries have a limited shelf life,replace them when the unit fails tocontrol the DVD player. There is aLED indicator light on the remotecontrol tha...

Liquid Crystal Display (LCD) flip-down screen The screen rotates down to view and into the housing to store when notin use. Be sure the screen is latched into the housing when being stored. 1. 7.0” (diagonal) active matrix liquid crystal display (LCD) screen. 2. Screen housing. 3. Dimmer switch. Pre...

Rear Seat Entertainment DVD System protection circuits High temperature sensor circuit • Excessively high temperatures may cause damage to the DVD player. • When the temperature of the DVD player becomes too hot, the hightemperature sensor circuit stops machine operation. DVD/CD HOT willilluminate i...

Inserting a CD/DVD Partially insert the CD/DVD into the slot and the system will fully pull inthe disc. Inserting the disc too far could cause the disc to jam in thesystem. Inserting a CD/DVD into the DVD player automatically turns the powerON and playback should begin. The counter is automatically ...

On-screen indicators Each time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible indicators: 1. CD track 2. DVD chapter 3. SYSTEM COUNTER — displays current viewing time of desired media.(HOURS:MINUTES:SECONDS) 4. DVD/ CD STATUS (PL...

Do not expose the liquid crystal display (LCD) flip-down screento direct sunlight or intensive ultraviolet rays for extensiveperiods of time. Ultraviolet rays deteriorate the liquid crystal. Be sure to review user manuals for video games and video gameequipment when used as auxiliary inputs for your...

• extremely hot or cold temperatures. • direct sunlight. • high humidity. • a dusty environment. • locations where strong magnetic fields are generated. Temperature extremes When the vehicle is parked under direct sunlight or in an extremely coldplace for a long period of time, wait until the cabin ...

VEHICLE NAVIGATION RADIO (VNR IF EQUIPPED) Your vehicle may be equipped with a Vehicle Navigation Radio (VNR)which allows you to listen to the radio, play CDs and also navigate thevehicle using navigation CDs. Your Vehicle Navigation Radio is equipped with many different featuresand controls. The la...

System overview 1. HOME: When the home location is empty, pressing and holding thiskey will store the vehicle’s currentlocation as home. Pressing the homekey after the home location has been set will calculate a route to that sethome location. 2. Eject: Press this control to eject an audio CD or a n...

2. Press the AM/FM control to selectthe desired frequency band. 3. Press the SEEK control to locatea station. To play a CD in the VNR: 1. Ensure that the ignition and theVNR system are ON. 2. Insert a CD into the single slot ofthe VNR and the CD will automatically begin play. If a CD is alreadyloade...

2. Press the NAV control to enterinto Navigation mode. 3. To enter a destination, ensurethat the vehicle is in the PARK position. 4. To navigate to home from thecurrent location, press HOME. If ahome location has not previouslybeen stored, pressing and holdingHOME will store the home location. Audio...

Automatic volume control (AVC) With this feature, radio volume changes automatically with vehicle speedto compensate for road and wind noise. To engage the AVC feature: 1. Press the MENU control. 2. Select AUDIO OPTIONS. 3. Select AVC, TRAFFIC, DSP. 4. Select AVC. 5. Use the cursor control to increa...

AM/FM select in CD mode Press to stop CD play and begin radio play. Radio reception factors: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km(24 miles). This range can be affected by “signal modulation.” Si...

Adjusting the levels 1. Press the MENU control. 2. Select the AUDIO OPTIONS softkey. 3. Select BASS, TREB, BAL orFADE. The bass adjust allows you toincrease or decrease the audiosystem’s bass output. The treble adjust control allows youto raise or lower the audio system’streble output.Speaker sound ...

(STOP) / AUX — If a DVD movie is playing, press to stop. If a movie is not playing, press to activate AUX mode. CD DJ Your vehicle is equipped with a CD DJ (CD changer). It is located in thecenter console. Radio power must be turned on to play the CDs in the CD DJ. Themagazine may be stored in the g...

will disable rear seat control (headphone/speaker icon on display willappear with a red slash through it). When RSC is active, pressing presets 2 and 4 simultaneously on the radiowill enable Dual Play mode (or the RSC can enable Dual Play mode bypressing the / button). The front speakers play the se...

• Within a Town/City – Lists entries for a specific city in alphabetical order. Certain categories may not be available in some areas and POIs may notall be listed. Up to date information also depends upon using the latestnavigation CD available. Previous destination The last 50 destinations entered...

• Resume route - The navigationsystem displays the Select RouteCriteria screen. Refer to Selecting Route Criteria earlier in this chapter. • Cancel route - Press to return tothe main menu. If the ignition is not turned off,simply continue along your highlighted route. Route changes or cancellations ...

2. Press the ADJUST control toselect the hours or minutes to set. 3. Use the cursor control to increaseor decrease the hours or minutes. 4. Press DONE to set the time. 5. Select the SET soft key tosynchronize/set the minutes andseconds to GPS time. The hours will remain at the user set value. You ma...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. MAX A/C: Uses recirculated a...

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMWITH HEATED AND COOLED SEATS (IF EQUIPPED) 1. A/C control: Press to engage/disengage the airconditioning in all modes exceptdefrost and floor/defrost. Uses outside air to cool the vehicle. 2. Recirculation control: Press to engage/disengage. Used to ma...

5. R (Rear defroster): Press to defrost the rear window. Refer to the Rear window defroster section in this chapter for more information. 6. Passenger cooled seat: Press to turn on the passenger side cooled seat. Press once for full cool (three lights above passenger cooled seatcontrol will be illum...

AUXILIARY A/C-HEATER CONTROLS (IF EQUIPPED) Your vehicle may be equipped with auxiliary climate controls. Theseallow the front or rear seat passengers to control airflow direction,temperature and fan level of the rear compartment to quickly heat orcool the vehicle. Auxiliary climate controls are loc...

Rear auxiliary controls (if equipped): Once the front auxiliary control is set to REAR, the rear seat passengersmay use the rear auxiliary controls in the floor console to make thedesired adjustments. 1. Temperature control: Determines temperature levels. Ifthe main climate control system iscooling ...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to turn on the headlamps. Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on when the headlamp control is in the , or p...

Daytime running lamps (DRL) (if equipped) Turns the foglamps on at full intensity output. To activate: • the ignition must be in the ON position and • the headlamp control must be in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or duringinclement weather. The ...

5. Locate the vertical adjuster oneach headlamp, then use a 10 mmsocket/wrench to turn the adjustereither counterclockwise (to adjustdown) or clockwise (to adjust up)aligning the upper edge of the lightpattern up to the horizontal line. 6. HORIZONTAL AIM IS NOTREQUIRED FOR THIS VEHICLEAND IS NON-ADJ...

Front row map/dome lamp (if equipped) The dome lamp lights when: • any door is opened, • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on, and • any of the remote entry controlsare pressed and the ignition is OFF. The map lamps are activated by pressing the controls on...

Replacing the interior bulbs Check the operation of all bulbs frequently. Map lamps To change the map lamp bulbs: 1. Use a small screwdriver toremove the map lamp lens. 2. To remove the old bulb, twist 1 ⁄ 4 turn and pull it out. 3. Twist in a new bulb. 4. Align and press the map lamplens back on an...

Approach lamp bulb removal (if equipped) To change the bulbs: 1. Make sure that all the doors areclosed and the interior lights haveautomatically turned off or theopposite mirror approach lamp hasturned off. 2. With a small flat tippedscrewdriver, insert the tip into theapproach light module slot lo...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

Changing the wiper blades It is recommended that wiper blades are renewed before winter. To replace the wiper blades: 1. Fold back the wiper arm andposition the wiper blade at rightangles to the wiper arm. 2. To remove, press the retainingclip (A) to disengage the wiperblade, then pull the blade dow...

Slide on rod feature (ifequipped) Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage. Note: To stow the visor back into the headliner, visor must beretracted before moving it backtowards the windshield. OVERHEAD CONSOLE The appearance of your vehicle’s ove...

Do not use the power point foroperating the cigarette lighterelement (if equipped). To prevent the fuse from beingblown, do not use the powerpoint(s) over the vehicle capacity of12 VDC/180W. To prevent the battery from beingdischarged, do not use the powerpoint longer than necessary whenthe engine i...

Not equipped with rear climatecontrol Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lightersocket. Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromit...

Power side view mirrors The ignition can be in any position to adjust the power side view mirrors. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt t...

Powerfold mirrors (if equipped) Pull the switch rearwards to autofold in and rearwards again to autofold back to design position.Powerfold the side mirrors incarefully when driving through anarrow space, like an automatic carwash. If needed, the mirrors can bemanually folded without using theswitch....

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...

Audio control features Press to select: • AM, FM1, FM2, • CD, or • DVD (if equipped). In AM, FM1, or FM2 mode: • Press MEM to select presetstations within the selected radioband. In CD mode: • Press MEM to select the nextselection on the CD. In any mode: • Press VOL + or − to adjustvolume. 2005 Expe...

Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink 威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, theprogrammed Homelink 威 buttons be erased for security purposes, refer to Programming in thi...

5. Press and hold the just-trained HomeLink 威 button and observe the indicator light. If the light is constant, programming is complete and yourdevice should activate when the HomeLink 威 button is pressed and released. Note: To program the remaining two HomeLink 威 buttons, begin with Step 2 in the “...

seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 . The indicator light will flash slowly and then rapidly after HomeLink 威 accepts the radio frequency signal. • Proceed with Step 4 in the “Programming” section. Operating the HomeLink 姞 Wirel...

For questions or comments, contact HomeLink 威 at www.homelink.com or 1–800–355–3515. ELECTRONIC COMPASS/TEMPERATURE DISPLAY WITHOUTMESSAGE CENTER (IF EQUIPPED) Outside air temperature In vehicles without Dual ElectronicAutomatic Temperature Control(DEATC), the outside temperaturedisplay is contained...

4. Drive the vehicle slowly (less than 3 mph [5 km/h]) in circles untilCAL indicator turns off. As many as 5 complete circles may be required. 5. The compass is now calibrated. MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, di...

Average fuel economy (AFE) Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/100km. If you calculate your average fueleconomy by dividing gallons of fuel used by 100 miles traveled(kilometers traveled by liters used), your figure may be different th...

1. To disable/enable the autolampdelay feature, select this functionfrom the SETUP control for thecurrent display mode. 2. Press the RESET control to selectthe new Autolamp delay values of >0, >10, >20, >30, >60, >90, >120 or>180. Reverse Sensing System (if equipped) This fea...

Warning display Status Door ajar Will not clear until condition iscorrected Reduced engine power Stop engine safely Check electronic throttlecontrol or engine fail safe mode Park brake engaged PARK ASSIST ON/OFF (if equipped). Displayed when the transmission is in R (Reverse) and the Backup Aid is d...

partially operable. If this warning stays on while the engine is running,contact your dealer for service as soon as possible. For furtherinformation, refer to AdvanceTrac 威 with RSC stability enhancement system in the Driving chapter. ADVTRAC OFF T/C ON with RSC (if equipped). Displayed on 4x4 vehic...

CENTER CONSOLE (IF EQUIPPED) The center console offers several useful storage features. These include: 1. Pen holder 2. Tissue holder 3. Large utility compartment 4. PalmPilot 娂 /PDA holder 5. Cupholders 6. Coin holder slots 7. Small utility compartment 8. Three power points Use only soft cups in th...

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tolock in. Make sure that the mat doesnot interfere with the operation ofthe accelerator or the brake pedal.To remove the floor mat, reverse theinstalla...

LUGGAGE RACK Your vehicle is equipped with a roofrack. The maximum recommendedload is 200 lbs (90 kg), evenlydistributed. If it is not possible todistribute the load, position it as farrearward as possible. To adjust cross-bar position (ifequipped): 1. Loosen the thumbwheel at bothends of the cross-...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your dealer suppliedkeys, replacement keys are available throug...

Childproof door locks When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoors are unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one door...

Sounding a panic alarm Press this control to activate thealarm. The personal panic alarm will cyclethe horn and parking lamps on/off. To deactivate the alarm, press thecontrol again or turn the ignition tothe 2 (ACCESSORY) or 3 (ON)position. Memory feature (if equipped) The remote entry system can a...

Deactivating the memory seat feature To deactivate this feature: 1. Press the SET control on the driver’s door panel. 2. Within 5 five seconds, press any control on the remote transmitterwhich you would like to deactivate and then press the SET control onthe driver’s door panel. 3. Repeat this proce...

Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmittershould operate normally after battery replacement. Replacing lost transmitters If a remote transmitter has been lost and you would like to remove itfrom the vehicle’...

Illuminated entry The lamps illuminate when the remote entry system is used to unlockthe door(s). The system automatically turns off after 25 seconds or when the ignitionis turned to the 2 (ACCESSORY) or 3 (ON) position. The dome lampcontrol must not be set to the off position for the illuminated en...

KEYLESS ENTRY SYSTEM (IF EQUIPPED) With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key, • release the liftgate glass, • enable or disable the autolock function, and • add or delete a 5–digit personal user code. Your vehicle has a factory set 5–digit code ...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 1(OFF/LOCK) position. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. Key information Your vehicle is supplied with two coded keys. Only a coded key will start...

SEATING Front row adjustable head restraints (if equipped) Your vehicle’s seats are equipped with two-way adjustable headrestraints. The purpose of these head restraints is to help limit headmotion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so t...

Lift handle to move seat forward orbackward. Seat recliner Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collisi...

Using the armrest (if equipped) Push the release control to movethe armrest up or down. Using the manual lumbar support The lumbar support control islocated on the outboard side of theseat. Turn the lumbar support controlforward for more support. Turn the lumbar support backwardfor less support. Usi...

Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

Memory seats/rearview mirrors/adjustable pedals (if equipped) This system allows automaticpositioning of the driver seat,outside rearview mirrors, andadjustable pedals to twoprogrammable positions. The memory seat control is locatedon the driver door. • To program position one, movethe driver seat, ...

• There is a filter located underboth front seats. • It can be accessed from thesecond row seat. Move the frontseat all the way forward and upto ease access. To remove climate controlled seatair filter: • Remove key from ignition. • Push on the outside rigid edge ofthe air filter at the center andro...

To install climate controlled seat air filter: • First, position the filter in it’shousing making sure that the farforward end is all the way up inthe housing. Then push in on thecenter of the outside edge of thefilter and rotate up into thehousing until it clips into position. REAR SEATS Second row...

3. To return the seat to a seatingposition, push down on the seatuntil the seat is latched to the floor. 4. With the seat in the flat back position, lift up on the lever located onthe side of the seat cushion. This will allow the seat back to be lifted tothe upright locked position.5. Lift the seatb...

1. Locate the handle on the side ofthe seat, lifting it to release theseatback. 2. Ensure that the seat back islocked in the down position byapplying pressure to the seat back. 3. Locate the latch strap at the frontof the seat and pull to release theseat into a kneel down load floorposition. A moder...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull onthe seatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a ...

Third row seats Ensure that no objects such as books, purses or briefcases are on thefloor in front of the third row seats or on the seat cushion beforelowering them. Ensure that the head restraints are lowered. Third row adjustable head restraints Your vehicle’s third row outboard seating positions...

Push the top of the control buttonto return the seatback to its originalposition. The power folding seats are designed to stall within 1–10 secondsof encountering an obstruction when opening or closing. Shouldthis occur, remove the obstruction and wait approximately 1–4minutes for the seat motor to ...

If any of these things happen, even intermittently, have the PersonalSafety System serviced at your dealership or by a qualified technicianimmediately. Unless serviced, the system may not function properly inthe event of a collision. Safety restraints precautions Always drive and ride with your seat...

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints. Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child any...

movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph (8km/h) or more, the combination safety belts will lock to help reduceforward movement of the driver and passengers. Automatic locking mode In this mode, the should...

How to disengage the automatic locking mode Unbuckle the combination lap and shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and return to thevehicle sensitive (emergency) locking mode. After any vehicle collision, the combination lap and shoulder beltsystem a...

Front and second row safety belt height adjustment Your vehicle has safety belt heightadjustments for the driver, rightfront passenger and second rowoutboard passengers. Adjust theheight of the shoulder belt so thebelt rests across the middle of yourshoulder. To lower the shoulder belt height,push t...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data) Reasons given... Consider... “Crashes are rareevents” 36 700 crashes occur every day. The more we drive, the more we are exposed to “rare” events,even for good drivers. 1 in 4 of us will be se...

Do not sit on top of a buckled safety belt to avoid theBeltMinder 娂 chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate theBeltMinder 娂 feature please follow the directions stated below. One time disable If at any time the driver/fro...

• Step 3 must be completed within 50 seconds after the safety beltwarning light turns off. 3. For the seating position being disabled, at a moderate speed, bucklethen unbuckle the safety belt 9 times, ending in the unbuckled state.(Step 3 must be completed within 50 seconds after the safety beltwarn...

be inspected after a collision. Ford Motor Company recommends that allsafety belt assemblies in use in vehicles involved in a collision bereplaced. However, if the collision was minor and a qualified technicianfinds that the belts do not show damage and continue to operateproperly, they do not need ...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

impact sensors, the system wiring, the air bag system readiness light, theair bag back up power and the air bag ignitors). Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Air bag readiness se...

Do not attempt to service, repair, or modify the Safety Canopy 娂 system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy 娂 . See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should alwayswear their safety belts...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions You are required by...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulderbelt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk ...

Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use the lap/shoulderbelt. If a seating position has alow seat back and no headrestraint, a backless booster seatmay place...

Follow all instructions provided by the manufacturer of thebooster seat. Never put the shoulder belt under a child’s arm or behind theback because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or tow...

6. Before placing the child into the child seat, forcibly move the childseat from side to side and forward to make sure that the seat is heldsecurely. If the child seat moves excessively, repeat Steps 5 through 6, orproperly install the child seat in a different position. Attaching child safety seat...

Second row seating positions 1. Position the child safety seat on the seat cushion. 2. Locate the tether anchor at the bottom back of the seat. • outboard seating positions • center seating position (ifequipped) 3. Route the child safety seat tether strap under the head restraint(outboard seats) and...

5. Rotate the tether strap, and clipthe tether strap to the anchor onthe seat frame. 6. Rotate the tether strap clip. 7. Tighten the child safety seat tether strap according to themanufacturer’s instructions. Third row seating position 1. Position the child safety seat on the center of the seat cush...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information ontransfer case operation and shiftingprocedures can be found in the Driving chapter . Information on transfer case maintenance can be fou...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

when you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. Never “bleed” or reduce airpressure when tires are hot.2. Remove the cap from the valve on one tire, then firmly press the tiregauge onto the valve and measure the pressure.3. Add enough air...

The installation of replacement tires with steel cord body plies in the tiresidewall may cause malfunction of the Tire Pressure Monitoring System(TPMS), and is not recommended (cord material information is moldedon the tire sidewall). Additionally, if your vehicle was originally equippedwith run-fla...

Your vehicle may be equipped with a dissimilar spare tire/wheel. Adissimilar spare tire/wheel is defined as a spare tire and/or wheel that isdifferent in brand, size or appearance from the road tires and wheels. Ifyou have a dissimilar spare tire/wheel, then it is intended for temporaryuse only. Thi...

If your vehicle is equipped with TPMS, have a flat tire serviced by adealer or qualified technician in order to prevent damage to the TPMSsensor, refer to Changing tires with TPMS later in this chapter. Replace the spare tire with a road tire as soon as possible. Location of the spare tire and tools...

Removing the spare tire 1. Fold the rear seat down. Refer to Rear seats in the Seating and safety restraints chapter. 2. Remove the jack handle andwinch extension from the tray andassemble them. 3. Open the spare tire winch accessplug in the bottom of thecompartment located behind the 3rdrow seat, v...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more ev...

information placard (label). Driving on a significantly under-inflated tirecauses the tire to overheat and can eventually lead to tire failure.Under-inflation also reduces fuel efficiency and tire tread life, and mayaffect the vehicle’s handling and stopping ability. Even if your vehicle isequipped ...

Low Tire WarningLight Customer Action Required Solid Warning Light 1. Check your tire pressure to ensure they areproperly inflated, refer to Inspecting and inflating your tires in this chapter. Ford recommends the use of a digital or dial typetire pressure gauge rather than a stick typetire pressure...

therefore it may take up to a minute for the light to turn off after youhave filled your tires to the recommended tire pressure. • If your vehicle has been parked for over 15 minutes, the sensors gointo a low power mode to conserve battery life and therefore onlytransmit about once an hour. If you i...

interference, and (2) This device must accept any interference received,including interference that may cause undesired operation. The Tire Pressure Monitoring System is NOT a substitute formanually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a t...

capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’sSafety C...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. 2005 Expedition (exd) Owners Guide (post-2002-fmt)USA_English (fus) Tires, Wheels and Loading 245

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

Special loading instructions for owners of pickup trucks andutility-type vehicles For important information regarding safe operation of this typeof vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this owner guide. Loaded vehicles, with a higher center of gravity, m...

Engine Rear axle ratio Maximum GCWR - kg (lb.) Trailer weight range (0 - maximum) kg (lb.) 4x4 5.4L with standard trailer tow package All 5397 (11900) 0–2721 (0–6000) 5.4L with optional trailer tow package All 6576 (14500) 0–3901 (0–8600) Note: For vehicles not equipped with the optional trailer tow...

• Weight distributing - requires an aftermarket weight distributing system which includes draw bar, hitch ball, spring bars and snap-upbrackets. The vertical tongue load of the trailer is distributed betweenthe truck and the trailer by this system. Mode Maximum Gross Trailer Weight - kg (lb.) Maximu...

4. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within a 1 ⁄ 2 ” (13 mm) of the reference point. After proper adjustment, the rear bumper should be no higher than inStep 3. 5. Turn the air suspension (if equipped) control to ON. Note: Adjusting ...

• Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assistin transmission cooling. (For additional information, refer to Understanding the gearshift positions of the 4–speed automatictransmission in the Drivin...

Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability, emissions and reliability. Replace the rear axle lubricant any time the axle has been submerged inwater. Rear axle lubricant quantities are not to be checked or ...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. ON, all electrical circuitsoperational. Warning lightsil...

5. Turn the key to 3 (ON) withoutturning the key to 4 (START). Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine Note: Whenever yo...

3. After idling for a few seconds, apply the brake, shift into gear anddrive. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine stillfails to start, press the accelerator to the floor and try again; this willall...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.5 cm) or adjust the heatingor air conditioning to bring in fresh air. BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenan...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy. STEERING Your vehicle is equipped with power steering. Power steering uses energyfrom the engine to decrease the driver’s effort in steering the vehicle. To p...

Press the bottom portion of theswitch to turn off the airsuspension. LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, thelimited slip axle functions like a standard rear axle. Ex...

The AdvanceTrac 威 with RSC button allows the driver to control theavailability of the AdvanceTrac 威 with RSC system. The RSC systemstatus is indicated by a warningindicator light with a “sliding car” icon in the instrument cluster that willflash when the system is activated and an indicator light in...

Do not alter or modify your vehicle’s suspension or steering; theresulting changes to the vehicle’s handling can adversely affectthe AdvanceTrac 威 with Roll Stability Control system. Also, do not install a stereo loudspeaker near the front center console orunder either front seat. The speaker vibrat...

3. Locate the round access plug onthe underside of the steeringcolumn cover. 4. Remove the access plug using a flat-head screwdriver, then insert yourfinger and pull the override button toward you. With the button pulledtoward you, apply the brake pedal and shift the transmission into N(Neutral). 5....

1 (First) Use 1 (Low) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to D (Drive). Selecting 1 (Low) at higherspeeds causes the transmission to shift to a lower gear, and will shift to 1(Low) after vehicle decelerates to the proper speed. Forced...

To help avoid personal injury, please read and understand thelimitations of the reverse sensing system as contained in this section. Reverse sensing is only an aid for some (generally large andfixed) objects when moving in reverse on a flat surface at “parkingspeeds”. Inclement weather may also affe...

CONTROL TRAC FOUR-WHEEL DRIVE (4X4) OPERATION(IF EQUIPPED) For important information regarding safe operation of this typeof vehicle, see Preparing to drive your vehicle in this chapter. If equipped with the Control Trac 4x4 System, and 4L (4x4 LOW)is selected while the vehicle is moving, the system...

Positions of the Control Trac system The Control Trac system functionsin four modes: • 2H (2WD HIGH) delivers power to the rear wheels only. This isappropriate for normal on-roaddriving on dry pavement. • A4WD (4X4 AUTO) provides electronic control four-wheeldrive with power delivered to allfour whe...

Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily underoff-road conditions. Avoid sharp turns or abrupt maneuvers in thesevehicles. Note: The Control Trac selector knob s...

Shifting from 2H, A4WD or 4H to 4L 1. Bring the vehicle to a stop andkeep the brake pedal depressed. 2. Place the gearshift in N (Neutral). 3. Move the control to the 4Lposition. If any of the above shift conditions are not met, the message center willdisplay the appropriate information. Note: Some ...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

called for. Avoid abrupt steering, acceleration or braking which couldresult in an increased risk of loss of vehicle control, vehicle rolloverand/or personal injury. Use all available road surface to return thevehicle to a safe direction of travel. • In the event of an emergency stop, avoid skidding...

slowly and avoid spinning your wheels. If the vehicle does slide, steer inthe direction of the slide until you regain control of the vehicle. If the transmission, transfer case or front axle are submerged in water,their fluids should be checked and changed, if necessary. Driving through deep water m...

Company strongly recommends that you do not make modifications suchas adding or removing parts (such as lift kits or stabilizer bars) or byusing replacement parts not equivalent to the original factory equipment. Any modifications to a vehicle that raise the center of gravity can makeit more likely ...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel / power distribution box The fuse panel is located under the right-hand side of the instrumentpanel. To remove the trim panel for accessto the fuse box, pull the paneltoward you and swing it out awayfrom the side and remove it. Toreinstall it, line up the tabs with t...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 7.5A* Run/Accessory - Front wipermotor, Instrument cluster, Rearwiper motor 2 20A* Turn signal/Hazard flasher,Stoplamp switch, Stoplamps,Center high-mount stop light(CHMSL), Turn signal...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 5 7.5A* Powertrain Control Module (PCM)(KA power), Speed controldeactivation switch, Manualclimate control mode switch,Stoplamp switch, Brake-shiftinterlock (BSI) solenoid, EATCcontrol head, Body SecurityModule (BSM) (K...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 20 30A* BSM (door locks, liftgate glassrelease relay), Liftgate glassrelease motor, Door/Liftgate lockmotors 21 15A* Instrument cluster (B+), Interior(courtesy) lamps, Puddle lamps(outside mirrors) 22 10A* Moonroof swit...

Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the transmissionmay have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Ov...

4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, near thebattery. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-)termin...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

• available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedures and/or to discontinue this service without notice and withoutincu...

before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be requested by the Board as well. Making a decision Board members review all available information related to eachcomplaint, including oral presentation...

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings. In the CAMVAP program,...

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate. These officials can inform youof local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can onl...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

roof racks, bumper step surfaces, mirror housings or the windshieldcowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jamb) toyour d...

• Cover the highlighted areas to prevent water damage when cleaningthe engine. • 5.4L 3V engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These pr...

Do not use sharp objects, such as a razor blade, to clean theinside of the rear window or to remove decals, as it may causedamage to the rear window defroster’s heated grid lines. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then with a clean, drycloth, or use Moto...

LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH EXPEDITION) Your leather seating surfaces have a clear, protective coating over theleather. For King Ranch Expedition leather seats, refer to separatesection in this chapter. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCle...

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl or plastics. Scratches In order to lessen the appearance of certain scratches and other wearmarks, apply conditioner on the affected area following the sameinstructions as in the Conditioning ...

Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A) Motorcraft Detail Wash (ZC-3–A) Motorcraf...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provi...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood until the liftcylinders hold it open. 2005 Expediti...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 3V– V8 engines 1. Battery 2. Automatic transmission fluid dipstick 3. Air filter assembly 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Engine oil filler cap 9. Windshield washer ...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the o...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by aqualified service technician. 7. Put the indicator ...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the scheduled maintenance information for the s...

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery,always shield your face and protect your eyes. Always provide properventilation. When lifting a plastic-case...

battery. When the battery is disconnected or a new battery is installed,the engine must relearn its idle and fuel trim strategy for optimumdriveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park), turn off al...

concentration testing is possible with a hydrometer or antifreeze tester(such as the Rotunda Battery and Antifreeze Tester, 014–R1060). Thelevel of coolant should be maintained at the “FULL COLD” level orwithin the “COLD FILL RANGE” in the coolant reservoir. If the level fallsbelow, add coolant per ...

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion...

necessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your dealer check the engine cooling system. Your coolingsystem may have a leak. Operating...

• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine damage. • Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine...

Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage. When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be a...

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce st...

2. Carefully turn the filler cap counterclockwise 1/4 turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on thefiller pipe. 5. Turn the filler cap clockwise 1/4 turn of a turn until at least a fewclicks are hear...

• Your Service engine soon indicator may come on. For more information on the Service engine soon indicator, refer to the Instrument Cluster chapter. Fuel Filter For fuel filter replacement, see your dealer or a qualified servicetechnician. Refer to scheduled maintenance information for the appropri...

• Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and...

These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly tightening the fuel cap. After threedriving cycles without these or any other temporary malfunctionspresent, the Check engine/Service engine soon light should turn off. (A driving cycle consi...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

The transmission fluid should be inthis range if at ambient temperature(50°F-95°F [10°C-35°C]). High fluid level Fluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/orengagement concerns and/or possible damage. High fluid...

When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Release two retai...

LUBRICANT SPECIFICATIONS Item Ford partname Ford partnumber Fordspecification Hinges, latches,striker platesand rotors, seattracks, fuel fillerdoor hinge andspring Multi-PurposeGrease XG-4 or XL-5 ESR-M1C159-Aor ESB-M1C93-B Lock cylinders,swing-awayspare tire carrierpadlock Penetrating andLock Lubri...

Vehicle dimensions 4x2 – inches (mm) 4x4 – inches (mm) (4) Wheelbase 119.0 (3023) 119 (3023) (5) Track - Front 67.0 (1701) 67.0 (1701) (5) Track - Rear 67.3 (1708) 67.3 (1708) 1 4 2005 Expedition (exd) Owners Guide (post-2002-fmt)USA_English (fus) Maintenance and Specifications 361

IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedto a vehicle and prescribe where theCertification label may be located.The Certification label is located onthe structure by the trailing edge ofthe ...

7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identificationnumber) is stamped on the engine block and transmission. Transmission/Transaxle code designations You can find a transmission/transaxle code on the vehicle certificati...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A ABS (see Brakes) .....................261 Accessory delay ........................123 Air bag supplemental restraintsystem ................................192, 196 and child safety seats ............194description ......................192, 196disposal ....................................199driver...

change oil soon warning,message center .......................327checking and adding ..............327dipstick ....................................327filter, specifications ........330, 354recommendations ...................330refill capacities ........................355specifications ................