Ford 2005 Escape v.4- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

• how fast the vehicle was traveling; and • where the driver was positioning the steering wheel. To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining cons...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Serviceengine soon warning light to come on. Refer to Fuel filler cap in the Maintenance and Specifications chapter. Without message center With message center Brake system...

Air bag readiness: If this light fails to illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately. A chime will alsosound when a malfunction in the supplemental restraint system has beendetected. Safety belt: Reminds you to fasten your safety bel...

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as safelypossible, switch off the engine and let the eng...

AM/FM STEREO / SINGLE CD RADIO (IF EQUIPPED) 1. BAL (Balance): Press / to shift sound to the left/rightspeakers. 2. FADE: Press / to shift sound to the front/rear speakers. 3. SCN (Scan): Press to hear a brief sampling of all listenablestations or CD tracks. Press again tostop. 4. CLK (Clock): To se...

To set the minute, press and hold CLK and press TUNE to decreaseor increase the minutes. 5. EJ (Eject): Press to eject a CD. 6. COMP (Compression): In CD mode, press to bring louder andsofter levels into more comfortablelistening level. The compression icon (c) will appear in the display. 7. SHUFFLE...

8. BAL (Balance): Press BAL; then press SEL / to shift sound to the right/left speakers. FADE: Press FADE; then press SEL / to shift sound to the front/rear speakers. 9. MENU: Press MENU and SEL to access clock mode, RDS on/off,Traffic, Program type, Show typeand Compression modes. Setting the clock...

AM/FM STEREO IN-DASH SIX CD MODULAR AUDIO (IF EQUIPPED) 1. CD: To begin CD play, press LOAD. The CD door will open whenthe system is ready to accept theCD. Insert the CD. The system will then load the CD and begin play aftera short pause. The disc number and track number will illuminate in thedispla...

14. FF (Fast forward): In CD/MP3 mode, press until desired selectionis reached. 15. REW (Rewind): In CD/MP3 mode, press until desired selectionis reached. 16. SAT (if equipped): Your radio comes equipped with Satellite Readycapability. The kit to enable theSatellite reception is available through yo...

21. COMP (Compression): Brings soft and loud CD passages togetherfor a more consistent listening levelwhen in CD mode. Press COMP to turn the feature ON/OFF. 22. Scan: Press SCAN to hear a brief sampling of radio stations orCD/MP3 tracks. Press again to stop. 23. CAT/Tune: Press or to manually tune ...

PREMIUM SATELLITE COMPATIBLE AM/FMSTEREO/CASSETTE/SINGLE CD/MP3 — LATE AVAILABILITY(IF EQUIPPED) 1. CD slot: Insert a CD with the label side up. CD units are designed to playcommercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re-recor...

2. CD Eject: Press to eject a CD. The radio will resume playing. 3. Mute: Press to MUTE playing media; press again to return to theplaying media. 4. Tape Eject: Press to eject the cassette. The radio will resumeplaying. 5. Tape 1–2/CD: Press to begin tape play. If a cassette is alreadyplaying, press...

button press to proceed to the next/last text display. ) The last text fieldshown on the display will become the new display message default. TEXT is also available when equipped with Satellite radio. Your radiocomes equipped with Satellite ready capability. The kit to enable Satellitereception is a...

18. Scan: Press to hear a brief sampling of all listenable stations,tape selections or CD tracks. Pressagain to stop. 19. Tune/CAT: TUNE: Works in radio mode only. PressTUNE / to change frequency down/up. CAT: CAT is only available when equipped with Satellite Radio. Your radio comes equipped with S...

RADIO RECEPTION FACTORS There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thunderstor...

CD units are designed to play commercially pressed 4.75 in (12 cm)audio compact discs only. Due to technical incompatibility, certainrecordable and re-recordable compact discs may not functioncorrectly when used in Ford CD players. Irregular shaped CDs,CDs with a scratch protection film attached, an...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. : Distributes outside air through the instrument panel ...

• Under normal weather conditions, do not leave the air flow selector inMAX A/C or O (OFF) when the vehicle is parked. This allows thevehicle to “breathe” using the outside air inlet vents. • Do not put objects under the front seats that will interfere with theairflow to the back seats. • Remove any...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to also turn on the headlamps. Headlamp battery saver The battery saver will shut off the exterior lamps 10 minutes after theignition switch has been turned off if the headlam...

Autolamp delay system (if equipped) If your vehicle has an autolamp delay feature, you can set the delay timeto keep the headlights on for up to three minutes after the key is turnedOFF. The delay time is set to 20 seconds at the factory, but the delaytime may be changed by following the steps below...

• the parking brake must be released. Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provideadequate lighting during these conditions. Failure to activate yourheadlamps under t...

PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control tobrighten. • Push and hold bottom of controlto dim. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the align...

dome and/or cargo lamp controls are in the DOOR position. Otherwise,interior lamps including the dome and/or cargo lamps will automaticallyextinguish after 30 minutes when the ignition key is OFF. BULBS Headlamp Condensation The headlamps are vented to equalize pressure. When moist air entersthe hea...

Function Number of bulbs Trade number Rear license platelamp 2 W5W All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer. Replacing the interior bulbs Check the operation of all bulbs frequently. Replacing headlamp bulbs 1. Make sure th...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down oneposition. Adjust the rotary control to thedesired speed setting. For normal or low speed wiperoperation, move control down twopositions from OFF. For high speed wiper operation,move control down three positionsfr...

Rear window wiper/washer controls For intermittent operation of rearwiper, rotate end of control upwardto the position. For normal speed rear wiperoperation, rotate control upward toON. To activate the rear washer, rotatethe control to the position and release. Changing the wiper blades 1. Pull the ...

To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has many sharp edges and can damage the micro edge of thewiper rubber element. TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down the ste...

• Install the transmitter (6) on to storage compartment door (3)aligning the actuator control (8) with the rubber actuator (1). Closethe storage compartment door (3) to verify proper fit. Do not forcethe storage compartment door (3) or you may break the door latch. Ifthe rubber actuator (1) is the p...

Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromits heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by yourwarranty. POWER WINDOWS Do not leave child...

Window lock (if equipped) The window lock feature disables allthe power windows except thedriver’s. To lock out all the window controlsexcept for the driver’s window pressthe right side of the control. Note: The window switches will not illuminate when the window control is in the LOCKED position. P...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET ACC control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator li...

• Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. CENTER CONSOLE Your vehicle is equipped with a variety of console features. Theseinclude: 1. Power point 2. Cupholders 3. Utility compartment 4. Ash cup (if ...

Selectable features Set This button is used to select andreset various functions shown in theINFO Menu. Info menu This control displays the followingcontrol displays: • Average Fuel Economy • Distance to Empty • Instantaneous Fuel Economy • Units (English/Metric) • Language • System Check • INFO Dis...

Liftgate ajar Warning returns after the ignition keyis turned from OFF to ON. Service emission sys Check fuel cap Low brake fluid Service brake system Check left headlamp Check right headlamp Check left high beam Check right high beam Check left turn lamps Check right turn lamps Engine change oil so...

LIFTGATE To open the rear window, pull theright side of the liftgate handle. To open the liftgate, pull the leftside of the liftgate handle. • Do not open the liftgate orliftgate glass in a garage or otherenclosed area with a low ceiling.If the liftgate glass is raised andthe liftgate is also opened...

Ensure that the posts are properly latched in mounting features.The cover may cause injury in a sudden stop or accident if it is not securely installed. Do not place any objects on the cargo area shade. They mayobstruct your vision or strike occupants of vehicle in the case of a sudden stop or colli...

NO BOUNDARIES RACK SYSTEM (IF EQUIPPED) Your vehicle may be equipped withan optional roof rack. This uniquefeature allows you to carry cargo onan inner roof rack as well as on theconventional roof rack. Themaximum load for the conventionalroof rack is 100 lbs (45 kg). Theinner rack can also hold 100...

6. Figure shows foot (A) clicked into place correctly. 7. With the locking tab (B) exposed on the foot, this figureshows the rack is not installedcorrectly. Repeat steps 3 through5 and secure the rack beforeloading cargo. Do not drive the vehicle if the inner roof rack is extended andloaded with car...

To stow the inner rack: 1. Rotate the handle on the lift barof the inner rack in the direction ofthe arrows on the handle and pullthe inner rack away from thebumper. 2. Lift the inner rack (pivoting atthe hinges). 3. Continue lifting the inner rackuntil it is parallel with the roof. 4. Slide the rac...

Always stow the inner rack on the roof when using an automatedcar wash. Do not attempt to open the liftgate or rear window when the rackis in the down position. This may damage the rack or yourvehicle. To ensure proper sliding function of your rack, keep the rackclear of debris. If debris is visible...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your dealer suppliedkeys, replacement keys are available throug...

7. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position.The horn will chirp one time to confirm the programming mode has beenexited. Repeat the procedure to turn the feature on or off. Door key unlocking/locking Two step door unlocking 1. Turn the key in the door cylinder to unlock t...

Childproof door locks • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when the doorsare unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for each door. Setting the lock for one...

• weak or dead transmitter battery. The remote entry system allows youto lock or unlock all vehicle doorswithout a key. The remote lockingand unlocking features will operateindependent of the ignition position;however, the panic feature will onlyoperate when the ignition is in the 1(LOCK) or 2 (ACCE...

Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed, the park/turn lamps will flash onceand the perimeter alarm (if equipped) will start the arming process. Formore information concerning the perimeter alarm, refer to Perimete...

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correc...

To reprogram the remote entrytransmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK) position to 3 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK)position and 3 (RUN). Note: The eighth turn must en...

Illuminated exit • The interior lights will illuminate when the key is removed from theignition. The lamps automatically turn off after 25 seconds. The dome and cargolamp controls must not be set to the OFF position for the illuminated exit system to operate. SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM S...

If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. Ifthis occurs, the vehicle should be taken to an authorized dealer forservice. Automatic arming The vehicle is armed immediatelyafter switching the igniti...

Programming spare keys You can program your own coded keys to your vehicle. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock 娂 keys. • You must have two previously programmed coded keys (keys thatalready operate your vehicle’s engine) and the new unprogrammedkey(s)...

When you press the control on the remote entry transmitter twice within three seconds, the horn will chirp once to confirm the doors,liftgate and hood are closed and locked, and the alarm is set. Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pr...

FRONT SEATS Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints T...

Adjusting the front manual seat Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. Press to raise or lower the frontportion of the seat cushion. 2005 Escape (204)...

Press to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Heated seats (if equipped) To operate the heated seats: • Push the control located on theseat to activate. • Push again to deactivate. The heated seats will activate when the...

The head restraints can be movedup and down. Lift the head restraintso that it is located directly or asclose as possible behind your head. Push control to lower or removehead restraint. Folding down rear seats 1. Raise the rear seat head restraintand remove. 2. Place the head restraint underthe fro...

3. Pull the seat release control. Note: Make sure the floor is clear of all objects before folding the seat. 4. Flip seat forward. Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will assure thatsafety belt does not get caught bystaying out of the seat back foldingpa...

To remove the rear cushion 1. Lift the yellow tab to release thehinges. 2. Pull the cushion to the outboardside of the vehicle. To install the rear cushion 1. Push the cushion to the inboardside of the vehicle. 2. Make sure that the hinges arelocked into place. SAFETY RESTRAINTS Personal Safety Syst...

position. The system is designed to help protect smaller drivers sittingclose to the driver air bag by providing a lower air bag output level. Front passenger sensing system For air bags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants...

Safety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The...

movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph (8 km/h)or more, the combination safety belts will lock to help reduce forwardmovement of the driver and passengers. Automatic locking mode In this mode, the should...

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive (emergency) locking mode. After any vehicle collision, the safety belt systems at all seatingpositions ...

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andfront passenger seating positions. The safety belt pretensioners activate during frontal collisions, and inside collisions and rollovers when the vehicle is equipped with the SafetyCanopy 娂 system. A sa...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning lightilluminates 1 minute and the warningchime sounds 6 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminated an...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day. The more we drive, the more we areexposed to ⬙ rare ⬙ events, even for good drivers. 1 in 4 of us will b...

Reasons given... Consider... ⬙ The people I’m with don’t wear belts ⬙ Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children andyounger brothers/sisters imitatebehavior they see. ⬙ I have an air bag ⬙ Air bags offer greater protection whenused with safety b...

Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front safety belt buckleass...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries. Airbags DO NOT inflate slowly; there isa risk of injury from a deploying airbag. All occupants of the vehicle, including the driver, should a...

Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame,bumper, front end body structure, tow hooks and B-pillar surrounding parts may affect the perfo...

How does the air bag supplemental restraint system work? The air bag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration sufficientto cause the air bag sensors to closean electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a co...

If it is necessary to modify an advanced front airbag system toaccommodate a person with disabilities, contact the Ford CustomerRelationship Center at the phone number shown in the CustomerAssistance section of this Owner’s Guide . Any alteration/modification to the front passenger seat mayaffect th...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Air Bag Technical WorkingGroup. These recommended testingprocedures help reduce the ris...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your dealership or by a qualified technician immediately. Unlessserviced, the system may not funct...

to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldeceleration. Several air bag system components get hot after inflation. Do nottouch them after inflation. If the side air bag hasdeployed, the air bag w...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions You are required by...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulderbelt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk ...

Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use the lap/shoulderbelt. If a seating position has alow seat back and no headrestraint, a backless booster seatmay place...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly tilt the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward and back. Ther...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information ontransfer case operation and shiftingprocedures can be found in the Driving chapter . Information on transfer case maintenance can be fou...

Every day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires and adjust ifrequired. At least once a month and beforelong trips, inspect each tire andcheck the tire pressure with a tiregauge (including spare, if equipped).Inflate all t...

Always inflate your tires to the Ford recommended inflation pressureeven if it is less than the maximum inflation pressure information foundon the tire. The Ford recommended tire inflation pressure is found onthe tire label or certification label which is located on the B-Pillar or theedge of the dr...

different in brand, size or appearance from the road tires and wheels. Ifyou have a dissimilar spare tire/wheel, then it is intended for temporaryuse only. This means that if you need to use it, you should replace it assoon as possible with a road tire/wheel that is the same size and type asthe road...

Remove the lug wrench from thejack in order to remove the sparetire from under the vehicle. Removing the spare tire or spare tire and tether (if equipped) 1. Insert the lug wrench through theaccess hole in the rear bumper. 2. Turn the handle counterclockwiseand lower the spare tire until it canbe sl...

If you are stowing a tire that requires reattaching it to thevehicle with a tether, perform these steps first, then proceed withthe steps following. 1. Place tire on end with valve stemfacing rearward, away from vehicle. 2. Place tether into bolt holes inwheel and attach lug nut using lugwrench. 3. ...

Bolt size Wheel lug nut torque* lb.ft. N • m M12 x 1.5 100 135 * Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford recommended replacement fasteners. When a wheel is installed, always remove any corrosion, dirt orforeign materials present on the mounting surfaces...

2. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, thewider the tire. 3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the whee...

• Temperature: The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and itsability to dissipate heat when tested under controlled conditions on aspecified indoor laboratory test wheel. 13. Maximum Permissible Inflation Pressure: Indicates ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more ev...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln/Mercury dealership to check ...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door. Lookfor “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for m...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. 2005 Escape (204) Owners Guide (post-2002-fmt)USA_English (fus) Tires, Wheels and Loading 174

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

• Do not tow a trailer until your vehicle has been driven at least 800 km(500 miles). • Refer to the instructions included with towing accessories for theproper installation and adjustment specifications. Do not exceed the maximum loads listed on the Certification label. Forload specification terms ...

Preparing to tow Use the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your dealer or a reliable trailerdealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch. You must distribute the...

• Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assistin transmission cooling. (For additional information, refer to Understanding the gearshift positions of the 4–speed automatictransmission in the Drivin...

Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability, emissions and reliability. Replace the rear axle lubricant any time the axle has been submerged inwater. Rear axle lubricant quantities are not to be checked or ...

STARTING Positions of the ignition 1. LOCK, locks the gearshift leverand allows key removal. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. RUN, all electrical circuitsoperational and warning lights willilluminate. This is the position t...

Starting the engine 1. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel until thekey turns freely. This condition mayoccur when: • the front wheels are turned • a front wheel is against the curb Turn the key to 4 (START),...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.5 cm) or adjust the heatingor air conditioning to bring in fresh air. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindi...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced Even when the ABS is disabled,normal braking is still effective. (If...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

Driving with an automatic overdrive transaxle Your automatic overdrive transaxleprovides fully automatic operation ineither D (Overdrive) or with theO/D OFF switch depressed. Drivingwith the gearshift lever in D(Overdrive) gives the best fueleconomy for normal drivingconditions. For manual control, ...

MANUAL TRANSAXLE OPERATION (IF EQUIPPED) Using the clutch Vehicles equipped with a manual transaxle have a starter interruptinterlock that prevents cranking of the engine unless the clutch pedal isdepressed.When starting a vehicle with a manual transaxle, you must: 1. Put the gearshift lever in then...

Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts when accelerating (recommended for best fueleconomy) 1-2 14 mph (22 km/h) 2-3 25 mph (40 km/h) 3-4 34 mph (55 km/h) 4-5 44 mph (70 km/h) Upshifts when cruising (recommended for best fuel economy) 1-2 1...

Parking your vehicle 1. Apply the brake and shift into theneutral position. 2. Set the parking brake. 3. Depress the clutch, then shift into1 (First). 1 2 4 R 3 5 1 2 4 R 3 5 2005 Escape (204) Owners Guide (post-2002-fmt)USA_English (fus) Driving 200

4. Turn the ignition to position 1(LOCK) to shut the engine off andremove the ignition key. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) For important information regar...

pavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surface. • It may be safer to stay on the apron or shoulder of the road and slowdown gradually before returning to the pavement. You may losecontrol if you do not slow down or if you turn t...

Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,turn the steering wheel only as rapidly and a...

be required from another vehicle. Remember, you may be able to backout the way you came if you proceed with caution. Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the...

or straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehandthe route you will use. Do not drive over the crest of a hill withoutseeing what conditions ar...

REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when R (Reverse) is selected and thevehicle is moving at speeds less than 3 mph (5 km/h). The system is noteffective at speeds above 3 mph (5 km/h) and may not dete...

The RSS detects obstacles up to 6 1 ⁄ 2 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the figures forapproximate zone coverage areas).As you move closer to the obstacle,the rate of the tone increases. Whenthe obstacle is less than 10 i...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

This switch is located in the frontpassenger’s footwell, behind aflip-up cover, by the kick panelaccess cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5....

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Passenger compartment fuse panel The fuse panel is located on theright-hand side of the centerconsole, by the instrument panel.Remove the panel cover to accessthe fuses. To remove a fuse use the fuse puller tool provided on the fuse panelcover. 2005 Escape (204) Owners Guide (post-2002-fmt)USA_Engli...

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A* Trailer tow park lamps 2 — Not used 3 15A* Front and rear park lamps 4 10A* Ignition switch 5 2A* Powertrain Control Module (PCMrelay), Fuel pump relay, Main fanrelay, High/Low spe...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 33 15A* Air bag module, Passenger Air bagDeactivation (PAD) indicatorlamp, Occupant ClassificationSensor (OCS) 34 5A* ABS module, Evac and Fill, Speedcontrol 35 5A* Heated seats module, 4WD * Mini fuse ** Cartridge fuse...

Do not attempt to push-start your vehicle. Automatictransmissions do not have push-start capability; doing so maydamage the catalytic converter. Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the tr...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMot...

Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford ofCanada and the dealer to resolve a factory-related vehicle serviceconcern have been unsatisfactory, Ford of Canada participates in animpartial third party mediation/arbitrati...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your dealer for completedetails about Ford Extended Service Plan coverage options, or visit theFord ESP website at ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint...

• 2.3L I4 • 3.0L DOHC V6 — Duratec Engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cl...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, tree sap, or o...

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the style ...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provi...

• Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease h...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission dipstick 4. Brake/Clutch fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil filler cap 9. Engine oil dipstick...

3.0L DOHC V6 Duratec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10. Windshield washer fluid reservoi...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds m...

• If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. • 2.3L I4 engine 2005 Escape (204) Owners Guide (post-2002-fmt)USA_English (fus) Maintenance and ...

• 3.0L DOHC V6 Duratec engine • If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must be removed from the engine by a qualified service t...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to scheduled maintenance information for the servi...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

• Add Motorcraft Premium Gold Engine Coolant(yellow-colored), VC-7–A (U.S., except CA, OR and NM),VC-7–B (CA, OR and NM), meeting Ford SpecificationWSS-M97B51–A1. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant fromyellow...

2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure ...

Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely cold climates (less than –34° F [–36° C ]): • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. •...

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tankmay cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, w...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel container whilefill...

It should not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octanerating. Aftermarket products could cause damage to the fuel system.Repairs to correct the effects of using an aftermarket product in yourfuel may not be cover...

NOT accurate as a measure of fuel economy. We do not recommendtaking fuel economy measurements during the first 1,000 miles (1,600 km)of driving (engine break-in period). You will get a more accuratemeasurement after 2,000 miles-3,000 miles (3,000 km–5,000 km). Filling the tank The advertised fuel c...

4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple calculations in order to determine fueleconomy: Calculation 1: Divide total miles traveled by total gallons used. Calculation 2: Multiply liters used by 100, then divide by total kilometers travel...

• Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended engine oil. Refer to Lubricant specifications in this chapter. • Perform all...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

BRAKE/CLUTCH FLUID RESERVOIR Brake and clutch systems are supplied from the same reservoir. The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toa...

If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician. An overfill condition oftransmission fluid may causeshift and/or engagementconcerns and/or possibledamage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may...

CLUTCH FLUID (IF EQUIPPED) The clutch master cylinder andbrake master cylinder are part ofthe same system; both are refillablethrough the brake master cylinderwith brake fluid. For moreinformation on brake fluidmaintenance, refer to Brake fluid in this chapter. Brake fluid is toxic. If brake fluid c...

REFILL CAPACITIES Fluid Ford PartName Application Capacity Brake fluid (andclutch fluid ifequipped) Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid All Fill to line onreservoir Engine oil(including filterchange) 6 Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 Su...

2 Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. 3 Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amountof transmission ...

Item Ford PartName orequivalent Ford PartNumber FordSpecification Engine coolant 1 MotorcraftPremium GoldEngine Coolant(yellow-colored) VC-7–A (U.S.,except CA, ORand NM),VC-7–B (CA, ORand NM) WSS-M97B51-A1 Engine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 SuperPr...

Item Ford PartName orequivalent Ford PartNumber FordSpecification Windshieldwasher fluid MotorcraftPremiumWindshieldWasherConcentrate ZC-32–A WSB-M8B16–A2 1 DO NOT USE Motorcraft Specialty Orange Engine Coolant VC-2. Refer to Adding engine coolant, in the this chapter. 2 Ensure the correct automatic...

VEHICLE DIMENSIONS Dimensions 4–Door - inches (mm) (1) Vehicle height/ Maximum height* 69.7 (1770)/70.3 (1786)* (2) Front track / rear 61.3 (1557)/60.9 (1548) (3) Overall width (body) 70.1 (1780) (4) Wheelbase 103.1 (2620) (5) Overall length 174.9 (4442) * Denotes a 4x4 vehicle with optional 16” tir...

Vehicle identification number (VIN) The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) 1. World manufacturer identifier 2. Brake type and gross vehi...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Accessory delay ..........................64 Air bag supplemental restraintsystem ................120–121, 127, 131 and child safety seats ............122description ..............121, 127, 131disposal ....................................133driver air bag ..........123, 129, 132indicator light ......