Ford 2003 Expedition v.2- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possibledamage to others, your vehicle and its equipment? In this guide, answersto such questions are contained in comments highlighted by the warningtriangle symbol. These comm...

SPECIAL NOTICESEmission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetail...

Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully.Your...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

If the light remains on, have your vehicle serviced at the first availableopportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter.You should drive in a moderate fashion (avoid heavy acceleration anddeceleration) and have your vehicle serviced at the fi...

Speed control Illuminates when the speed controlis activated. Oil pressure/Engine coolant Illuminates when the engine coolanttemperature is above the normalrange or the engine oil pressure isoutside normal range. Check theengine oil and coolant level refer to Adding engine oil and Adding coolant in ...

Four wheel drive low (if equipped) Illuminates when four-wheel drivelow is engaged. If the light continuesto flash have the system serviced. Four wheel drive high (if equipped) Illuminates when four-wheel drive isput in high range. If the lightcontinues to flash have the systemserviced. Check air su...

GAUGES Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If itenters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, switc...

Engine oil pressure gauge Indicates engine oil pressure. Atnormal operating temperature, theneedle will be in the normal range(the area between the “L” and “H”);if the needle goes below the normalrange, stop the vehicle as soon assafely possible and switch off theengine immediately. Check the oillev...

If the key is left in the ON position during fueling, a minimum of 22.2 L(six gallons) must be added to the fuel tank in order for the gauge toinstantaneously update. If less than six gallons is added, the gauge willtake between five to twenty minutes to update. Speedometer Indicates the current veh...

• Optional instrument cluster Press and release the TRIP/RESETbutton to toggle between theodometer and trip odometer display.Press and hold the button to reset. Tachometer Indicates the engine speed inrevolutions per minute. Driving with your tachometerpointer continuously at the top ofthe scale may...

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD 1. EJ (Eject): Press to stop and eject a tape. 2. EJ (Eject): Press to stop and eject a CD. 3. BASS: Allows you to increase or decrease the audio system’s bassoutput. Press BASS then press SELto decrease or increase the bass levels. TREB (Treble): Allows you t...

In CD mode, REW control reverses the CD within the current track. FF (Fast Forward): Works in tape and CD modes. In the tape mode, tape directionautomatically reverses when the end of the tape is reached. In CD mode, FF advances the CD within the current track. 10. MUTE: Press to mute the playing me...

11. AUTOSET: Press to set first six strong stations into AM, FM1 orFM2 memory buttons; press again toreturn to the original presetstations. If there are less than six strong stations available on thefrequency band, the remaining memory preset controls will all store thelast strong station available....

PREMIUM IN-DASH SIX CD SOUND SYSTEM AUDIOPHILE IN-DASH SIX CD SOUND SYSTEM 1. SEEK: Works in radio or CD mode. Press and releaseSEEK / for previous/next strong station or track. Entertainment Systems 24

2. REW (Rewind): In CD mode, press to reverse within the currenttrack. FF (Fast forward): In CD mode, press to advance within the currenttrack 3. COMP or DSP COMP (Compression): The compression feature operates in CD mode and brings soft and loud CD passages together for a more consistentlistening l...

To activate Dual Play mode (rearseat passengers listen to a differentplaying media than the front seatpassengers): • Press the speaker/headphonecontrol. • Press the MODE control tochange audio sources (forheadphone mode only) • Use the SEEK, VOLUME andMEMORY controls to make adjustments to the playi...

Turning the rear speakers on and off Press the headphone/speakercontrol to turn the rear speakers on(Single Play mode) or off (Dual Playmode). Using headphones/Dual Play mode Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. DUAL PLAYil...

Memory preset control Push the MEMORY controlsuccessively to allow rear seatpassengers to scroll through the6 memory presets in AM, FM1 orFM2. Push the MEMORY control in CDmode (if equipped) to advance tothe next disc. Seek function • In radio mode, press to find the next listenable station downthe ...

RADIO FREQUENCIES AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz RADIO RECEPTION FACTORS There are three factors th...

Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to play commercially pressed 12 cm (4.75 in)audio compact discs only. Due to technical i...

7. Auxiliary jacks Insert lines for standard video game players. 8. STOP/EJECT control Press once to stop DVD play. Press again to eject the DVD. 9. DISPLAY (DISP) control Press to enable on screen display of player menu and user displayadjustments. DVD control features Menu control Press the MENU c...

FWD or REV control for slow motion playback. Three different speedsare available depending on how long the control is held. Press thecontrol once for slow motion playback. Press the control again todisengage slow motion playback. Press the PLAY/PAUSE control toreturn to normal playback mode. User me...

Parental control To enable or disable your Rear SeatEntertainment DVD System,simultaneously press the memorypreset controls 3 and 5 on the radio face. For further information about the Rear Seat Controls, refer to Rear Seat Controls section in this chapter. Wireless headphones Your system is equippe...

1. 7.0” (diagonal) active matrix liquid crystal display (LCD) screen. 2. Screen housing. 3. Dimmer switch. Press +/- to increase/decrease the brightness of thescreen. Playback and format • The DVD player of your Rear Seat Entertainment DVD System canonly be used in the “playback” mode. (The DVD play...

Playing a video game/auxiliary device 1. Connect the video line from your video game device to the YELLOWauxiliary input jack.2. Connect the left and right audio lines to the WHITE and RED auxiliaryinput jacks respectively.3. Press the MODE control until DVD/CD AUX (no disc in player) orDVD/CD play ...

Do not attempt to service, repair or modify the Rear Seat EntertainmentDVD System. See your Ford or Lincoln Mercury dealer. Do not insert foreign objects into the DVD compartment. The front glass on the liquid crystal display (LCD) flip-downscreen may break when hit with a hard surface. If the glass...

However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to consult the dealer or anexperienced ra...

System overview 1. HOME: When the home location is empty, pressing and holding thiskey will store the vehicle’s currentlocation as home. Pressing the homekey after the home location has been set will calculate a route to that sethome location. 2. Eject: Press this control to eject an audio CD or a n...

2. Press the AM/FM control to selectthe desired frequency band. 3. Press the SEEK control to locatea station. To play a CD in the VNR: 1. Ensure that the ignition and theVNR system are ON. 2. Insert a CD into the single slot ofthe VNR and the CD will automatically begin play. If a CD is alreadyloade...

2. Press the NAV control to enterinto Navigation mode. 3. To enter a destination, ensurethat the vehicle is in the PARK position. 4. To navigate to home from thecurrent location, press HOME. If ahome location has not previouslybeen stored, pressing and holdingHOME will store the home location. Audio...

AM/FM select The AM/FM control works in radio,CD and navigation modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press to stop CD play and begin radio play. ...

If a navigation CD is in the head unit and you press CD, the system willautomatically search for an audio CD in the CD DJ and begin play if it ispresent. Adjusting the levels 1. Press the MENU control. 2. Select the AUDIO OPTIONS softkey. 3. Select BASS, TREB, BAL orFADE. The bass adjust allows you ...

(STOP) / AUX — If a DVD movie is playing, press to stop. If a movie is not playing, press to activate AUX mode. CD DJ Your vehicle is equipped with a CD DJ (CD changer). It is located in thecenter console. Radio power must be turned on to play the CDs in the CD DJ. Themagazine may be stored in the g...

will disable rear seat control (headphone/speaker icon on display willappear with a red slash through it). When RSC is active, pressing presets 2 and 4 simultaneously on the radiowill enable Dual Play mode (or the RSC can enable Dual Play mode bypressing the / button). The front speakers play the se...

• Within a Town/City – Lists entries for a specific city in alphabetical order. Certain categories may not be available in some areas and POIs may notall be listed. Up to date information also depends upon using the latestnavigation CD available. Previous destination The last 50 destinations entered...

• Resume route - The navigationsystem displays the Select RouteCriteria screen. Refer to Selecting Route Criteria earlier in this chapter. • Cancel route - Press to return tothe main menu. If the ignition is not turned off,simply continue along your highlighted route. Route changes or cancellations ...

General information Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford or Lincoln Mercury couldvoid user’s authority to operate the equipment. This equipment has beentested and found to comply with the limits for a Class B digital device,pursuant to Part ...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature control2. Mode selector control3. A/C control 4. Rear defrost control 5. Fan speed control FAN SPEED CONTROL Controls the volume of air circulatedin the vehicle. TEMPERATURE CONTROL KNOB Controls the temperature of theairflow ins...

MODE SELECTOR CONTROL Controls the direction of the airflowto the inside of the vehicle. The A/C compressor will onlyfunction if the outside temperatureis above approximately 2°C (35°F) • MAX A/C – Distributes recirculated air through the instrument panelregisters. Max A/C is noisier than A/C, but m...

A/C control A/C Used to manually enable or disable the operation of the air conditioningin all modes except Floor & Defrost, Defrost and Max A/C. When manual A/C is selected (On) the indicator will be lit. When manualA/C is selected (Off) the indicator will not be lit. In Floor & Defrost and...

TEMPERATURE CONVERSION Press the F/C control to switchbetween Fahrenheit and Celsiustemperature on the display. Thetemperature in Celsius will bedisplayed in half-degree increments. The English/Metric control on thetrip computer and message center(if equipped) will not change thetemperature display....

function if the outside temperature is above approximately 2°C (35°F).In Defrost, the A/C will operate automatically if the outside temperatureis above approximately 2°C (35°F); however, the A/C indicator will notbe lit. In automatic operation, the air conditioning operates as necessary toachieve th...

MANUAL OVERRIDE CONTROLS The manual override controls allow you to determine where airflow isdirected. To return to full automatic control, press AUTO. The A/C compressor will only function if the outside temperature isabove approximately 2°C (35°F). • OFF-Outside air is shut out and the fan will no...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to turn on the headlamps. Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on when the headlamp control is in the , or p...

Daytime running lamps (DRL) (if equipped) Turns the foglamps on at full intensity output. To activate: • the ignition must be in the ON position and • the headlamp control must be in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or duringinclement weather. The ...

5. Locate the vertical adjuster oneach headlamp, then use a 10 mmsocket/wrench to turn the adjustereither counterclockwise (to adjustdown) or clockwise (to adjust up)aligning the upper edge of the lightpattern up to the horizontal line. 6. HORIZONTAL AIM IS NOTREQUIRED FOR THIS VEHICLEAND IS NON-ADJ...

Front row dome lamp/ map light (if equipped) The dome lamp lights when: • any door is opened, • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on, and • any of the remote entry controlsare pressed and the ignition isOFF. The map lights are activated by pressing the cont...

Map lamps To change the map lamp bulbs: 1. Use a small screwdriver toremove the map lamp lens. 2. To remove the old bulb, twist 1 ⁄ 4 turn and pull it out. 3. Twist in a new bulb. 4. Align and press the map lamplens back on and test the lamp operation. Replacing headlamp bulbs 1. Make sure that the ...

Approach lamp bulb removal (if equipped) To change the bulbs: 1. Make sure that all the doors areclosed and the interior lights haveautomatically turned off or theopposite mirror approach lamp hasturned off. 2. With a small flat tippedscrewdriver, insert the tip into theapproach light module slot lo...

WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed position. The bars of varying length are forintermittent wipers. When in thisposition rotate the control upwardfor fast intervals and downward forslow intervals. Push (tap) the end of the st...

Forward storage bin and conversation mirror (if equipped) The storage compartment may beused to store two pairs of sunglassesor similar objects. Press the releasecontrol to open the storagecompartment. The door will openslightly and can be moved to fullopen. The conversation mirror on thecover allow...

AUXILIARY POWER POINT Power points are designed foraccessory plugs only. Do nothang any type of accessory oraccessory bracket from the plug.Improper use of the power pointcan cause damage not coveredby your warranty. On vehicles equipped with a centerconsole there are three powerpoints located in th...

Not equipped with rear climatecontrol POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. Driver Controls 112

Press the control to turn the mirrorOFF or AUTO. The mirror will automatically returnto the normal state whenever thevehicle is placed in R(Reverse)(when the mirror is on) to ensure a bright clear view whenbacking up. Power side view mirrors The ignition can be in any position to adjust the power si...

POWER ADJUSTABLE FOOT PEDALS The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P(Park) position. Press and hold the rocker control toadjust accelerator and brake pedal. • Press the bottom of the control toadjust the pedals toward you. ...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off,the previously programmed setspeed will be erased. To set a speed • Press SET+. For speed control tooperate, the speed control mustbe ON and the vehicle speedmust be greater than 48 km/h (30m...

To disengage speed control • Depress the brake pedal. Disengaging the speed control willnot erase the previouslyprogrammed set speed. Pressing OFF will erase thepreviously programmed set speed. To return to a previously set speed • Press RES. For RES to operate,the vehicle speed must be fasterthan 4...

Indicator light This light comes on when either theSET ACCEL or RES controls arepressed. The vehicle speed must beat or above 48 km/h (30 mph). Itturns off when the speed controlOFF control is pressed, the brake orclutch is applied, or the ignition is turned to the OFF position. STEERING WHEEL CONTR...

In any mode: • Press VOL + or − to adjustvolume. Climate control features Press TMP + or - to adjusttemperature. Press + or - to adjust fan speed. HOMELINK 姞 UNIVERSAL TRANSCEIVER (IF EQUIPPED) The HomeLink 威 Universal Transceiver, located on the driver’s visor, provides a convenient way to replace ...

When programming your HomeLink 威 Universal Transceiver to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink 威 Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required...

Gate Operator & Canadian Programming During programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time forHomeLink 威 to accept the signal from the hand-held transmitter. After completing steps 1 and 2outlined in the “Programming” section, replace step 3 w...

Erasing HomeLink 姞 buttons To erase the three programmedbuttons (individual buttons cannotbe erased): • Press and hold the two outerHomeLink 威 buttons until the red indicator light begins toflash-after 20 seconds. Releaseboth buttons. Do not hold forlonger that 30 seconds. HomeLink 威 is now in the t...

1. Start the vehicle. 2. To enter the compass calibrationmode, press and hold theTRIP/RESET button for greater thaneight seconds. The display will thenshow CAL in the display window. 3. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles untilCAL indicator turns off. As many as 5 complete...

Compass zone/calibration adjustment 1. Determine your magnetic zone byreferring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine. 4. From Info menu, select theCompass/Odometer function. (Donot select Trip, DTE, or AFE. Thetop of the message center must beblank). 5. Press and...

10. The compass is now calibrated. Average fuel economy (AFE) Select this function from the INFOmenu to display your average fueleconomy in liters/100 km ormiles/gallon. If you calculate your average fueleconomy by dividing liters of fuelused by 100 kilometers traveled(miles traveled by gallons used...

1. To disable/enable the easyentry/exit feature, select thisfunction from the SETUP control forthe current display mode. 2. Press the RESET control to turnthe easy entry/exit ON or OFF. Reverse mirrors (if equipped) This feature automatically tilts the side view mirrors down when thevehicle is put i...

5. OIL PRESSURE 6. TIRE PRESSURE SYSTEM (if equipped) 7. BRAKE FLUID LEVEL 8. CHARGING SYSTEM System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to s...

Warning display Status Door ajar Warning returns after 10 minutes Liftgate ajar Low fuel level Check charging system Low brake fluid level Low oil pressure Check engine temperature Reduced engine power Stop engine safely Tire pressure system fault(if equipped) Warning returns after the ignition keyi...

To return to normal overdrive mode,press the transmission controlswitch again. The O/D OFF will nolonger be illuminated. When you shut off and re-start yourvehicle, the transmission willautomatically return to normal(Overdrive) mode. For additional information about the gearshift lever and the trans...

Do not pull the liftgate handle from the bottom. Doing so maycause wrist or arm injury. Make sure the liftgate is closed to prevent exhaust fumes frombeing drawn into the vehicle. If you must drive with the liftgate open, keep the vents open so outside air comes into the vehicle. LUGGAGE RACK The re...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock 娂 Passive Anti-Theft System for more information. POWER DOOR LOCK...

REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This devicemust accept any interference received, including interference that may...

Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Unlock all doors using the powerdoor lock/unlock control. Insert akey in the ignition a...

Smart unlocking feature The smart unlocking feature prevents you from locking yourself out ofthe vehicle by unlocking the doors if the key is in the ignition and thedriver’s door is open/ajar when the vehicle doors were locked using thepower lock/unlock control. The smart unlocking feature operates ...

6. Press the unlock control, then press the lock control. The horn willchirp once if autolock was deactivated or twice (one short and one longchirp) if autolock was activated. 7. Turn the ignition to OFF. The horn will chirp once to confirm theprocedure is complete. The autolock feature may also be ...

Programming your own personal entry code To program your own code:8. Enter factory set code (keypad will illuminate when pressed).9. Press 1/2 control within five seconds of step 1. 10. Enter your personal 5 digit code.Enter each digit within five secondsof previous one. 11. After the code is entere...

• When the ignition is in the ON position, the indicator will glow for 3seconds to indicate normal system functionality. If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the ON position. If thisoccurs, the vehicle should be t...

If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle, or • Have your vehicle towed to a dealership or a locksmith. The key codeswill need to be erased from your vehicle and new key codes will needto be re-coded. Replacing coded keys can be very...

SEATING Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to reduce the risk ofinjuring people in a collision or sudden stop. Lift handle to move seat forward orbackward. Seat recliner Alway...

• There is a filter located underboth front seats. • It can be accessed from thesecond row seat. Move the frontseat all the way forward and upto ease access. To remove climate controlled seatair filter: • Remove key from ignition. • Push on the outside rigid edge ofthe air filter at the center andro...

To install climate controlled seat air filter: • First, position the filter in it’shousing making sure that the farforward end is all the way up inthe housing. Then push in on thecenter of the outside edge of thefilter and rotate up into thehousing until it clips into position. REAR SEATS Second row...

3. To return the seat to a seatingposition, push down on the seatuntil the seat is latched to the floor. 4. Lift the seatback to the upright position. Always latch the vehicle seat to the floor, whether the seat isoccupied or empty. If not latched, the seat may cause injury during a sudden stop. Fol...

3. Locate the latch strap at the frontof the seat and pull to release theseat into a kneel down load floorposition. A moderate force may berequired to move the seat forwardand down. Once the second row seats are inthe down position, the front seatsmay be readjusted. Returning to the upright position...

3. To return the seat to the uprightposition, lift the seatback until thelatch is fully engaged. Adjusting the second row 20% seat (if equipped) Lift the handle to move the seatforward or backward. Note: This seat can be moved forward to keep a child in a childrestraint close to the front seat occup...

Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Third row seats Ensure that no objects such as books, purses or briefcases are on thefloor in front of the third row seats or on the seat cushion befo...

Push the bottom portion of thecontrol button to lower the desiredseatback. Push the top of the control buttonto return the seatback to its originalposition. The power folding seats are designed to stall within 1–10 secondsof encountering an obstruction when opening or closing. Shouldthis occur, remo...

The head restraints can be movedup and down. Push control to lower head restraint. SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of air bag-relat...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and warning light are repaired. If any of these things happen, even intermittently, have the PersonalSafety System serviced at your dealership or by a qualified technicianimmediately. Unless serviced, ...

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints. Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child any...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The front outboard, rear outboard, and second and third row centersafety restraints in the vehicle are combination lap and shoulder belts.The front center safety restraint (if equipped) is a manually-adjustablelap belt. All...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly. In addition, allsafety belts should be checked for proper function. Failure to replacethe belt and retractor assembly could incre...

Front and second row safety belt height adjustment Your vehicle has safety belt heightadjustments for the driver, rightfront passenger and second rowoutboard passengers. Adjust theheight of the shoulder belt so thebelt rests across the middle of yourshoulder. To lower the shoulder belt height,push t...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition... The BeltMinder 娂 feature will not activate. The purpose of the BeltMinder 娂 is to remind occasional wearers to wear safety belts all of the time. The following are reasons most often given for n...

Reasons given... Consider... “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’twear belts” Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children an...

• The ignition switch is in the OFF position • All vehicle doors are closed • The driver’s safety belt is unbuckled • The parklamps/headlamps are in OFF position (If vehicle is equippedwith Autolamps, this will not affect the procedure.) To reduce the risk of injury, do not deactivate/activate theBe...

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label. Also, use the safety belt extension only if the safety belt is tooshort for you when fully extended. Do not use extensions to change the fit of the s...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries. Airbags DO NOT inflate slowly; there isa risk of injury from a deploying airbag. All occupants of the vehicle, including the driver, should a...

Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. The front passenger air bag is not designed to offer protection toan occupant in the center front seating position. Modifying or adding equipment to the front...

How does the air bag supplemental restraint system work? The air bag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbag inflation. The fact that the air bags did notinflate in a collision do...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS ...

Safety Canopy 姟 system (if equipped) Do not place objects ormount equipment on or near the headliner at the siderailthat may come into contact with adeploying Safety Canopy 娂 . Failure to follow these instructions mayincrease the risk of personal injuryin the event of a collision. Do not lean your h...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Air Bag Technical WorkingGroup. These recommended testingprocedures help reduce the ris...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to the Air bag readiness section in the Instrument Cluster chapter. Routine maintenance of the air bag is not required. A difficulty with the syst...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. Children and safety belts If the child is the pro...

When children should use booster seats Children need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the vehicle seat andlap/shoulder belt to fit properly. Generally this is when they weigh about80 lbs (about 8 to 12 years old). Booster seats should be u...

• Those with a high back. If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Both can be used in any vehicle in a seating position equipped withlap/shoulder belts if your child is over 40 lbs...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

• The second row center seat can be moved forward to keep a child in achild restraint close to the front seat occupants. The seat should bemoved to the full rearward position when it is occupied by olderchildren or adults. Ford recommends the use of a child safety seat having a top tether strapand L...

Installing child safety seats in the center front seating position Always transport children 12 years old and under in the rearseats and always properly use appropriate child restraints. It is safer to install child safety seats in seating positions thathave child seat anchors. The front seat has no...

The tether strap anchors in your vehicle are in the following positions(shown from top view): • Second row bench seat • Second row bucket seats Attach the tether strap only to the appropriate tether anchor asshown. The tether strap may not work properly if attached somewhere other than the correct t...

Third row seating position 1. Position the child safety seat on the center of the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the anchor webbing loop for the seating position. • You may need to pull back thetop of the hinged panel along thebottom of...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. ON, all electrical circuitsoperational. Warning lightsil...

5. Turn the key to 3 (ON) withoutturning the key to 4 (START). Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine Note: Whenever yo...

• The anti-lock system does not always reduce stopping distance.Always leave enough room between your vehicle and the vehicle infront of you to stop. • We recommend that you familiarize yourself with this brakingtechnique. However, avoid taking any unnecessary risks. ABS warning lamp ABS The ABS war...

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released. Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park). The parking brake is not recommended to stop a mo...

If the steering wanders or pulls, check for: • Underinflated tire(s) on any wheel(s) • Uneven vehicle loading • High crown in center of road • High crosswinds • Wheels out of alignment • Loose or worn suspension components Speed sensitive steering Your vehicle is equipped with engine speed sensitive...

When exiting the vehicle, the air suspension will automatically lower thevehicle to its lowest height to provide easier exit. You may hear a buzz orclick from the air suspension system when the ignition is turned off. Theair suspension system will stay active for 40 minutes after the ignition isturn...

Press the bottom portion of theswitch to turn off the airsuspension. LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, thelimited slip axle functions like a standard rear axle. Ex...

AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a park/brake-shift interlock feature thatprevents the gearshift lever from being moved from P (Park) when theignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out...

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working proper...

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) With the gearshift lever in R(Reverse), the vehicle will movebackward. Always come to acomplete stop before shi...

• additional engine downhill braking is desired. If towing a trailer, referto Driving while you tow in the Trailer towing section. To return to (Overdrive) mode, press the transmission control switch (TCS). The TCIL will no longer be illuminated. Each time the vehicle is started, the transmission wi...

The RSS detects obstacles up to2 meters (6 ft.) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the figures forapproximate zone coverage areas).As you move closer to the obstacle,the rate of the tone increases. Whenthe obstacle is less than 25.0 cm(10 i...

If equipped with the Control Trac 4x4 System, and 4L (4x4 LOW)is selected while the vehicle is moving, the system will notengage. This is normal and should be no reason for concern.Before 4L (4x4 LOW) can be engaged, the vehicle must bebrought to a complete stop, the brake pedal depressed and thetra...

• 4H (4X4 HIGH) provides mechanically locked four-wheel drive power to front and rear wheels. The “4X4” light will illuminate in theinstrument cluster when this position is selected. This position is notrecommended for use on dry pavement. This position is only intendedfor severe winter or off-road ...

Using the Control Trac system Shifting from 2H to A4WD or 4H Move the control to the A4WD or4H position at any forward speed upto 88 km/h (55 mph). The “4X4”light in the instrument cluster willilluminate if 4H is selected. Shifting from A4WD to 4H Move the control from A4WD to 4Hat a stop or while d...

Shifting from 4L to 4H, A4WD or 2H 1. Bring the vehicle to a stop andkeep the brake pedal depressed. 2. Place the gearshift in N (Neutral). 3. Move the control to the 4H,A4WD or 2H position. Note: Some noise may be heard as the system shifts or engages. Driving off-road with truck and utility vehicl...

Basic operating principles • Do not use 4H (4x4 HIGH) or 4L (4x4 LOW) on dry, hard surfacedroads. This may damage the drivelines and axles. • Drive slower in strong crosswinds which can affect the normal steeringcharacteristics of your vehicle. • Be extremely careful when driving on pavement made sl...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. If the ignition system gets wet, thevehicle may stall. Once thro...

possibly rolling over. Whenever driving on a hill, determine beforehandthe route you will use. Do not drive over the crest of a hill withoutseeing what conditions are on the other side. Do not drive in reverseover a hill without the aid of an observer. When climbing a steep slope or hill,start in a ...

You should carefully observe the recommended tire inflation pressurefound on the safety compliance certification label attached to the leftfront door latch post pillar (a label may also be found on the fuel capfiller door). Failure to follow tire pressure recommendations canadversely affect the way ...

• Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating isdetermined by subtracting the vehicle curb weight for eachengine/transmission combination, any required option weight for trailertowing and the weight of the driver from ...

Special loading instructions for owners of pickup trucks andutility-type vehicles For important information regarding safe operation of this typeof vehicle, see the Preparing to drive your vehicle section in this chapter. Loaded vehicles, with a higher center of gravity, may handledifferently than u...

• Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter. • Service your vehicle more frequently if you tow a trailer. Refer to thesevere duty schedule in the schedul...

Towing trailers beyond the maximum recommended gross trailerweight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehiclecontrol, vehicle rollover and personal injury. If your vehicle is equipped with AdvanceTrac 娂 , you may experi...

Preparing to tow Use the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your dealer or a reliable trailerdealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to theaxle. You must distribute the lo...

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The trailer brakes must meet local and Federalregulations. Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s bra...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • If you ...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch bypushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 25A Natural Natural — — — 30A Green Green Green Pink Pink 40A — — Orange Green Green 50A — — Red Red Red 60A — — Blue — Yellow 70A — — Tan — Brown 80A — — Natural — Black Passenger compartment fuse panel ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 7 7.5A* Radio (start signal) 8 10A* Rear window defroster switch,Rear window defroster indicator(climate control head), Heatedoutside mirrors 9 — Not used 10 20A* Trailer tow back-up lamps relay,Trailer tow 7–wire conne...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 14 10A* Daytime Running Lamps (DRL)ignition relay coil, DigitalTransmission Range Sensor(DTRS) back-up lamps, Trailertow back-up lamps relay coil,Electrochromatic mirror,Navigation radio, Manual A/Cblend door actuator 1...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 23 10A* RH low beam 24 15A* Interior demand lamps (frontmap/dome lamp, 2nd rowdome/map lamp, glovecompartment lamp, cargo lamp,roof rail lamps, vanity mirrorlamps), Battery saver relay coil,Battery saver relay power 25 ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 33 20A* Canister vent solenoid, HEGOsensors, VMV solenoid, IntakeManifold Tuning Valve (IMTV-4.6Lengine) solenoid, A/C compressorclutch relay coil, EGR vacuumregulator (EVR) solenoid 34 20A* PCM, Fuel injectors, Fuel pu...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 103 30A** ABS/AdvanceTrac 娂 module (pump motor) 104 30A** LH 3rd row seat relay, LH 3rd rowseat switch, LH 3rd row seatmotor 105 40A** Spare 106 30A** Trailer tow battery charge relay,Trailer tow 7–way connector(battery...

Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the followinglocations: Item Location Spare tire Under the vehicle, just forward ofthe rear bumper Jack tools and jacking instructions Under the access panel located in the floor compartment behind therear s...

Tire change procedure To prevent the vehicle from moving when you change a tire, besure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) tothe tire being changed. If the vehicle slips off the jack, you or someone else...

4. Use the tip of the jack handle toremove any wheel trim. Loosen eachwheel lug nut one-half turncounterclockwise but do not removethem until the wheel is raised offthe ground. 5. Position the jack according to thejack locator arrows found on theframe and turn the jack handle andextension tool assem...

Stowing the spare tire 1. Lay the tire on the ground, near the rear of the vehicle, with the valvestem side facing up. 2. Slide the wheel partially underthe vehicle and install the retainerthrough the wheel center. Afterdoing so, pull on the cable to alignthe components at the end of thecable. 3. As...

may have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Over time, theadaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery ...

4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, near thebattery. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-)termin...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you return to the authorizeddealer where your vehicle was purchased when warranty repairs areneeded. However, you may also take your vehicle to another...

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action un...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMot...

Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

WINDOWS AND WIPER BLADES The windshield, rear window and wiper blades should be cleanedregularly. If the wiper does not wipe properly, substances on thewindshield, rear window or the wiper blades may be the cause. Thesemay include hot wax treatments used by commercial car washes, treesap, or other o...

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. Do not use cleaning solvents, bleach or dye on the vehicle’sseatbelts, as these actions may weaken the belt webbing. CLEANING THE CLIMATE ...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the styl...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood until the liftcylinders hold it open. Maintenance a...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 engines 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Engine coolant reservoir 8. Air filter assembly 9. Windshield washer flui...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL...

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the eng...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the scheduled maintenance guide forthe service ...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. With your foot on the brake pedal and with the A/C on, put thevehicle in D (Drive) and allow the engine to...

60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -36° C (-34° F). • Boiling protection up to 129° C (265° F). • Protection against rust and other forms of corrosion. • Enables calibrated gauges t...

Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium GoldEngine Coolant since a Ford-approved recycling process is not yetavailable. Used engine coolant should be disposed of in an appropriate manner. ...

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cool...

operation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to prevent enginedamage, therefore:1. Pull off the road as soon as safely possible and turn off the engine.2. Arrange for the vehicle to be taken to a service facility.3. If this is ...

Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel container whilefill...

Many of the world’s automakersissued the World-wide Fuel Charterthat recommends gasolinespecifications to provide improvedperformance and emission controlsystem protection for your vehicle.Gasolines that meet the World-wideFuel Charter should be used whenavailable. Ask your fuel supplierabout gasoli...

possible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel economy. We do not recommendtaking fuel economy measurements during the first 1,600 km (1,000 miles)of driving (engine break-in period). You will get a more accuratemeasurement after 3,000 km–5,...

3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple calculations in order to determine fueleconomy: Calculation 1: Multiply liters used by 100...

• Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended...

It is important to note the box in the lower left corner of the windowsticker. These numbers represent the range of fuel economy expected onthe vehicle under optimum conditions. Your fuel economy may varydepending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is e...

permitted to intentionally remove an emission control device or preventit from working. Information about your vehicle’s emission system is onthe Vehicle Emission Control Information Decal located on or near theengine. This decal identifies engine displacement and gives some tune upspecifications. P...

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engine idles, turn thesteering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the...

TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance guide for scheduled intervals forfluid checks and changes. Your transmission does not consume fluid.However, the fluid level should be checked if the transmission is notworking properly, i.e., if the transmi...

DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that requirelubrication. Refer to the scheduled maintenance guide for maintenanceintervals. If the original universal joints are replaced with universal jointsequipped with grease fittings, lubrication will al...

government test course. For example, a tire graded 150 would wear oneand one-half (1 1/2) times as well on the government course as a tiregraded 100. The relative performance of tires depends upon the actualconditions of their use, however, and may depart significantly from thenorm due to variations...

• Adjust tire pressure to recommended specifications found on theCertification Label. Tire pressure information can also be found on theTire Information label located on the inside of the fuel filler door. • Check tires for proper air pressure monthly. Check spare tire forproper air pressure every s...

Replacing the tires Replace the tires when the wearband is visible through the tiretreads. Due to exposure to theelements and exhaust you shouldreplace the spare tire when youreplace the other tires. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire s...

pressure readings to the receiver module located in the vehicle. Thereceiver module then transmits the status to the message center. Formore tire warning information, refer to the Message Center in the Driver controls chapter. This device complies with part 15 of the FCC rules and with RS-210 ofIndu...

Fluid Ford PartName Application Capacity 5.4L V8 enginewith 1 rowradiator 21.0L(22.2 quarts) 4.6L V8 enginewith 1 rowradiator and auxrear heat 21.0L(22.2 quarts) 5.4L V8 enginewith 1 rowradiator and auxrear heat 23.0L(24.3 quarts) Front axlelubricant Motorcraft SAE75W-90Premium 4x4Front AxleLubrican...

LUBRICANT SPECIFICATIONS Item Ford partname Ford partnumber Fordspecification Hinges, latches,striker platesand rotors, seattracks, fuel fillerdoor hinge andspring Multi-PurposeGrease XG-4 or XL-5 ESR-M1C159-Aor ESB-M1C93-B Lock cylinders,swing-awayspare tire carrierpadlock Penetrating andLock Lubri...

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincoln, Mercury or Ford ofCanada dealer. These quality accessories have been specificallyengineered to fulfill your automotive needs; they are custom desi...

A ABS (see Brakes) .....................210 Accessory delay ........................113 Air bag supplementalrestraint system ........183–184, 188 and child safety seats ............185description ......................184, 188disposal ....................................191driver air bag ..............

brake ..........................................11charging system ........................12check coolant ............................13cruise indicator .........................13door ajar ....................................13engine oil pressure ...................13high beam ........................