Ford 2002 Taurus v.3- User Manual

BREAKING-IN YOUR VEHICLE There are no particular guidelines for breaking-in your vehicle. Duringthe first 1 600 km (1 000 miles) of driving, vary speeds frequently. This isrecommended to give the moving parts a chance to break in. SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty in...

Please read the section Air bag in the Seating and safety restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear-facing child or baby seats should NEVER be used in front of a passenger side air bag. MIDDLE EAST/NORTH AFRI...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat TetherAnchorage Brake System Anti-Lock Brake System Brake Fluid -Non-Petroleum Based Tr...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

If the light remains on, have your vehicle serviced at the first available opportunity. Note: The light will illuminate if vehicle refueling is conducted with the engine running. Never refuel vehicle with the engine running. Light is blinking: Engine misfire is occurring which could damage your cata...

when the ignition is moved from the ON position to START position, thelight will momentarily illuminate prior to reaching the START position).It also illuminates if the parking brake is engaged. If the brake systemwarning light does not illuminate as described, seek service immediately.Illumination ...

Charging system Illuminates when the battery is notcharging properly. Engine oil pressure Illuminates when the oil pressurefalls below the normal range. Checkthe oil level and add oil if needed.Refer to Engine oil in the Maintenance and specifications chapter. Low coolant (if equipped) Illuminates w...

Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the key is removedfrom the ignition and the driver’s door is opened. Key-in-ignition warning chime Sounds when the key is left in the ignition and the driver’s door isopened. Park brake warning chime Sounds when the parkin...

This gauge indicates the temperature of the engine coolant, not thecoolant level. If the coolant is not at its proper level the gauge indicationwill not be accurate. Fuel gauge Displays approximately how muchfuel is in the fuel tank. The fuelgauge may vary slightly when thevehicle is in motion or on...

AM/FM STEREO Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on...

Bass/treble adjust • The bass adjust control allowsyou to increase or decrease theaudio system’s bass output. • The treble adjust control allowsyou to increase or decrease theaudio system’s treble output. Speaker balance/fade adjust • Speaker sound distribution can beadjusted between the right andle...

AM/FM select The AM/FM select control works inradio mode. Press the AM or FMcontrol to enter radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. Pressing the AM or FM controls whe...

Setting the clock To set the hour, press and hold thehour (H) control. When the desiredhour appears, release the control. To set the minute, press and holdthe minute (M) control. When thedesired minute appears, release thecontrol. Your vehicle is equipped with a special feature that allows you to ac...

MACH T AUDIO SYSTEM WITH AM/FM STEREO/CASSETTE Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when th...

Scan function The scan function works in radio,tape or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stationson the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a shor...

Radio station memory preset The radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stations and twelveFM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band withthe AM/FM select control. 2. ...

Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to movethrough the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hol...

Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. If you wish...

Seek function The seek function control works inradio or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in CD mode • Press to seek to the previous track of the ...

AM/FM select The AM/FM select control works inradio, and CD modes (if equipped).Press the AM or FM control to enterinto radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. Pressin...

Setting the clock To set the hour, press and hold thehour (H) control. When the desiredhour appears, release the control. To set the minute, press and holdthe minute (M) control. When thedesired minute appears, release thecontrol. Your vehicle is equipped with a special feature that allows you to ac...

CD CHANGER (IF EQUIPPED) Your CD changer is either located in the trunk, the console or the rightside cargo area storage compartment. 1. Slide the door to access the CDchanger magazine. 2. Press to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder releaseknob (C), pull the ...

CD units are designed to play commercially pressed 12 cm (4.75in) audio compact discs only. Due to technical incompatibility,certain recordable and re-recordable compact discs may notfunction correctly when used in Ford CD players. Irregularshaped CDs, CDs with a scratch protection film attached, an...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Mode Selector Control Controls the direction of the airflowto the inside of the vehicle. ...

• (Defrost) – Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield.If the temperature is about 6°C (43°F) or higher, the air conditionerwill automatically dehumidify the air to reduce fogging. Operating tips • In humid weather conditi...

Turning the EATC on Press AUTO, any of the override controls or the fan speed control. TheEATC will only operate when the vehicle is running. Turning the EATC system off Press OFF. The outside temperaturefunction will continue to operateuntil the ignition is turned off. Automatic operation Press AUT...

Temperature selection The display window indicates theselected temperature, function(AUTO or one of the overridecontrols) and manual control of fanspeed ( ) if automatic fan speed is not desired. To control the temperature, selectany temperature between 18°C(65°F) and 29°C (85°F) by pressingthe temp...

Fan speed ( ) When AUTO is pressed, fan speed isadjusted automatically for existingconditions. You can override fanspeed at any time. To control fanspeed manually, press the fancontrol or the steering wheel fanspeed control (if equipped) tocancel automatic fan speedoperation. Press the control up fo...

• OFF-Outside air is shut out and the fan will not operate. For shortperiods of time only, use this mode to reduce undesirable odors fromentering the vehicle. Displaying outside temperature Press OUTSIDE TEMP to displaythe outside air temperature. It willbe displayed until OUTSIDE TEMPis pressed aga...

• If your vehicle has been parked with the windows closed during warmweather conditions, the air conditioner will perform more efficiently incooling the vehicle if driven for two or three minutes with thewindows open. This will force most of the hot, stale air out of thevehicle. Once the vehicle has...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second position toturn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the he...

The dome lamp will stay on if thecontrol is moved to the passengerside position. When the control is inthe middle position, the lamp willonly come on when a door isopened. If the control is moved tothe driver’s side position, the lampwill not come on at all. • ON: The dome light will stay on. • DOOR...

Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is inOFF position. 2. Remove the bolt from theheadlamp housing. 3. At the back of the headlamp, pryup and remove the two retainer pinsto release the headlamp assemblyfrom the vehicle and pull headlampforward. 4. Remov...

5. Disconnect the electricalconnector from the bulb by pullingrearward. 6. Remove the bulb retaining ring byrotating it counterclockwise. 7. Remove the old bulb from thelamp assembly by pulling it straightout of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and...

2. Install the bulb retaining ring over the plastic base and lock the ringby rotating clockwise until it snaps into place. 3. Connect the electrical connector to the bulb. 4. Install the protective dust shield and lock the shield by rotating itclockwise until it locks into position. 5. Carefully pos...

5. Carefully pull bulb straight out ofthe socket and push in the newbulb. 6. Install the bulb socket into thelamp assembly by rotating itclockwise. 7. Carefully position the headlampassembly onto the vehicle. 8. Hold the headlamp assemblysnugly against the vehicle and installthe retainer pins straig...

Replacing high-mount brakelamp bulbs — Wagon only 1. Open liftgate. 2. Remove two screw covers, screwsand handle from liftgate. 3. Remove two screws and the lowertrim panel from the liftgate. 4. Remove the upper trim panel. 5. Remove the rubber plug from thelower access hole in the upperportion of t...

7. Carefully lift the lamp assemblyaway from the liftgate. 8. Remove the bulb socket byrotating it counterclockwise andpulling it out from the lampassembly. 9. Carefully pull the bulb straightout of the socket and push in thenew bulb. 10. To complete installation, followthe removal procedure in reve...

3. On the underside of the spoiler,remove the two decorative screwcovers (on the LED module). 4. Remove the two screws that areholding the LED module in place. 5. Remove the wiring harnessgrommet and disengage theelectrical connector. 6. Replace the LED module. 7. To complete installation, followthe...

WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed position. The bars of varying length are forintermittent wipers. When in thisposition rotate the control upwardfor fast intervals and downward forslow intervals. Push the control on the end ...

Press the washer control to activatethe rear washer. The wiper willcome on when the washer control ispressed, if it is not already on. Windshield wiper blades Check the wiper blades for wear at least twice a year or when they seemless effective. Substances such as tree sap and some hot wax treatment...

TILT STEERING Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the control. Never adjust the steering wheel when the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the v...

Do not plug optional electrical accessories into the cigarettelighter. Use the power point. POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. One touch down • Press...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press the leftside of the control. Press the rightside to restore the window controls. Accessory delay (if equipped) With accessory delay, the window swit...

If highly magnetized items (such as magnetic mount antennas) areplaced very near the compass the display will change to “C” for 15seconds, then display all segments until the magnetized item is removed.If a “C” is displayed, refer to Compass calibration adjustment. Most geographic areas (zones) have...

Compass calibration adjustment Perform this adjustment in an open area free from steel structures andhigh voltage lines. 1. Start the vehicle. 2. Press and hold the COMP side ofthe control for approximately sixseconds until “C” appears in themirror display. 3. Drive the vehicle slowly (lessthan 5 km...

Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a scraper orattempt to readjust the mirrorglass if it is frozen in place.These actions could cause damage to the glass...

Do not use the speed control in heavy traffic or on roads thatare winding, slippery, or unpaved. To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off,the previously programmed setspeed will be erased. To set a speed • Press SET+. For speed cont...

To set a higher set speed • Press and hold SET +. Releasethe control when the desiredvehicle speed is reached or • Press and release SET + tooperate the Tap-Up function.Each press will increase the setspeed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehiclespee...

Pressing OFF will erase thepreviously programmed set speed. To return to a previously set speed • Press RES. For RES to operate,the vehicle speed must be fasterthan 48 km/h (30 mph). Indicator light This light comes on when either theSET or RES controls are pressed. Itturns off when the speed contro...

• Compact disc changer (if equipped) • Tissue holder • Rear A/C vent • Rear ashtray (see your Ford, Lincoln Mercury dealer to obtain rearashtray Use only soft cups in the cupholder. Hard objects can injure youin a collision. If your vehicle is equipped with the column shift and a bench seat, it hasa...

You will need a pocket adapter thatis compatible with your cellphone.The adapter will plug into thecenter console. To order your phone specific PocketAdapter Kit, which includes thepocket adapter, Owner’s manual andAudio Guide, call 1(888) 801–2355or visit Cellport at www.cellport.com/pockets. Distr...

CARGO AREA FEATURES Storage compartment Your vehicle comes equipped with astorage compartment in the floor ofthe cargo area. An additionalcompartment is in the rear trimpanel on the right. Always put theload you are carrying as far forwardas possible. Cargo net (if equipped) (Wagon) The cargo net se...

Do not place any objects on the cargo area cover. They mayobstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. The cover may cause injury in a sudden stop or accident if it isnot securely installed. Rewinding the shade With extended use, the cargo shade ...

The cover may cause injury in a sudden stop or accident if it isnot securely installed. Cargo utility hooks (Sedan) The utility hooks located in side the trunk can be used to attach a cargonet to secure lightweight objects or hang small items on. Do not hangmore than 12 kg (20 lbs) on the hooks. The...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock y Passive Anti-Theft System for more information. POWER DOOR LOCK...

Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment. The remote entry system allows you to lock or unlock all vehicle doors,trunk and liftgate without a key. The remote entry features only operate with the veh...

Sounding a panic alarm Press this control to activate thealarm. To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON. Panic alarm will only operate withthe ignition in the OFF position. Unlocking the liftgate/trunk Press the control to unlock theliftgate/trunk. Replacing ...

1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART. 2. Place the positive (+) side of newbattery in the same orientation.Refer to the diagram inside thetransmitter unit. 3. Snap the two halves backtogether. Replacement of...

• Within 20 seconds, program a remote transmitter by pressing anybutton on a transmitter. The doors will lock/unlock to confirm that theremote transmitter has been programmed. (If more than 20 secondspass before pressing a remote transmitter button, the programmingmode will exit and the procedure wi...

Deactivating/activating perimeter lamps There are 2 methods to enable/disable this feature. One through yourdealer and the second with a power door lock sequence using thefollowing instructions: 1. Turn the ignition key to RUN, then press the power door UNLOCKcontrol button 3 times. 2. Turn the igni...

Programming your own personal entry code 1. Enter the factory-set code (keypad will illuminate when pressed). 2. Press the 1/2 control within fiveseconds of step 1. 3. Enter your personal 5 digit code.Enter each digit within five secondsof the previous one. The power doorlocks should cycle (lock/unl...

1. To unlock the driver’s door, enter one of the two codes. After pressingthe fifth number, the driver’s door unlocks. 2. To unlock the passenger’s door(s)and liftgate (wagon), press the 3/4control within five seconds ofunlocking the driver’s door. 3. To unlock the trunk or liftgate(wagon), enter th...

Pressing the power door UNLOCK control button again will toggle theAutolock/Relock states. • Turn ignition to OFF to exit. SECURILOCK Y PASSIVE ANTI-THEFT SYSTEM SecuriLock y passive anti-theft system is an engine immobilization system. This system is designed to prevent the engine from being starte...

dealership. Your dealership can program your key or you can “do ityourself.” Refer to Programming spare keys. Certain items may cause vehicle starting issues: Certain items may cause vehicle starting issues: • Large metallic objects • Electronic devices on the key chain that can be used to purchaseg...

Please read and understand the entire procedure before you begin. 1. Insert the first previouslyprogrammed coded key into the ignition and turn the ignition from 3(OFF) to 4 (ON) (maintain ignitionin 4 (ON) for at least one second). 2. Turn ignition to 3 (OFF) then 2(LOCK) and remove the first coded...

The system is ready to arm whenever the key is removed from theignition. Any of the following actions will prearm the alarm system: • Press the remote entry lockcontrol (doors opened or closed). • Press 7/8 and 9/0 controls on thekeyless entry pad at the sametime to lock the doors (doorsopened or cl...

If the doors/hood or liftgate (wagon) are not closed and you press theremote entry transmitter twice to confirm the doors are locked, the horn willchirp twice to warn you that a door/hood or liftgate (wagon) is still open. Disarming the system You can disarm the system by any of the following action...

SEATING Adjustable head restraints Your vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head restraints is to help limithead motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it is l...

Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to reduce the risk ofinjuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

REAR SEATS 2nd seat/split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additionalcargo space. To lower the seatback(s) frominside the vehicle, pull tab to releaseseat back and then fold seatbackdown. When raising the seatback(s), make sure you hear the sea...

How does the personal safety system work? The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to crash severity and occupantconditions. A collection of crash and occupant sensors providesinformation to the Restraints Control Module (RCM). During a c...

safety belt pretensioner activation depending upon safety belt usage.Refer to Safety Belt section in this chapter. Front safety belt pretensioners The safety belt pretensioners are designed to tighten the safety beltsfirmly against the occupant’s body during a collision. This maximizes theeffectiven...

Safety belt precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passe...

Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing freeshoulder belt length adjustment to your movements and locking inresponse to vehicle movement. For example, if the driver brakessuddenly or turns a corner sharply, or the vehicle receives an impact ofapproxim...

• Grasp the shoulder portion andpull downward until the entirebelt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recomm...

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions. The safety belt pretensioners are designed to activate only when thesafety belts are fastened during certain frontal or near-frontal collisionswith sufficient...

Front safety belt height adjustment Your vehicle has safety belt heightadjustments for the driver and frontpassenger. Adjust the height of theshoulder belt so the belt restsacross the middle of your shoulder. To lower the shoulder belt height,pull the control down and slide theheight adjuster down. ...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

grasp the tongue so that it is parallel to the webbing and slide thetongue upward. Provide enough length so that the tongue can reach thebuckle. To fasten the belt, pull the combination lap and shoulder belt from theretractor so that the shoulder belt portion of the safety belt crosses yourshoulder ...

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare events” 36 700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even for gooddrivers. 1 in 4 of us will be se...

Reasons given... Consider... “I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely toDIE. Safety ...

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8inch) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the s...

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM Your vehicle is equipped with a crash sensing and diagnostic modulewhich records information about the air bag and sensor systems. In theevent of a collision this module may save information related to thecollision including information about the air bag system ...

The air bag supplemental restraints are an integral part of the PersonalSafety System. They are designed to be deployed in cases where thePersonal Safety System has determined the occupant conditions andcrash severity are appropriate to activate these devices. Refer to the Personal Safety System sec...

Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its ...

How do the air bag supplemental restraints work? The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (...

How does the side air bag system work? The side air bag system consists ofthe following: • An inflatable nylon bag (air bag)with a gas generator concealedbehind the outboard bolster ofthe driver and front passengerseatbacks. • A special seat cover designed toallow airbag deployment. • The same warni...

Several air bag systemcomponents get hot after inflation. Do not touch them afterinflation. If the side air bag hasdeployed, the air bag will not function again. The sideair bag system (including theseat) must be inspected andserviced by a qualifiedtechnician in accordance withthe vehicle service ma...

Always follow the instructions and warnings that come with any infant orchild restraint you might use. When possible, always place children under age 12 in the rearseat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up high across the stomach.If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat ...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. 3. OFF, shuts off the engine withoutlocking the steering wheel...

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosedareas. Exhaust fumes can be toxic. Always open the garage d...

Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as theengine starts. The key will return to4 (ON). 2. If the tem...

If you should experience cold weather starting problems on (E d 85) ethanol, and neither an alternative brand of (E d 85) ethanol nor an engine block heater is available, the addition of unleaded gasoline to yourtank will improve cold starting performance. Your vehicle is designed tooperate on (E d ...

Anti-lock brake system (ABS) (if equipped) On vehicles equipped with an anti-lock braking system (ABS), a noisefrom the hydraulic pump motor and pulsation in the pedal may beobserved during ABS braking events. Pedal pulsation coupled with noisewhile braking under panic conditions or on loose gravel,...

With the ABS light on, the anti-lockbrake system is disabled and normalbraking is still effective unless thebrake warning light also remainsilluminated with parking brakereleased. (If your brake warning lamp illuminates, have your vehicleserviced immediately.) Parking brake Apply the parking brake w...

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy. Park brake warning chime Sounds when the parking brake is set, the engine is running and thetransaxle is not in P (Park) or N (Neutral). The chime will shut o...

During Traction Control y operation, the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine compartment and theengine will not “rev-up” when you push further on the accelerator. Thisis normal system behavior. The Traction Control y on/off ...

• High crosswinds • Wheels out of alignment • Loose or worn suspension components AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the ON positio...

Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transaxle may occur. Do not rock the vehicle for more than a few minutes or damageto the transaxle and tires may occur or the engine may overheat. Always set the parking brake fully and make sure the gearshi...

If your vehicle is equipped with aconsole mounted gearshift, youmust press the thumb button on theside of the gearshift lever to movethe gearshift lever from P (Park). To put your vehicle in gear, start theengine, depress the brake pedal,then move the gearshift lever out ofP (Park). Hold the brake p...

1 (First) Use 1 (First) for when added enginebraking is desired when descendingsteep hills. The automatic transaxle will shift tothe proper gear to ascend any gradewithout any need to shift to 1(First). Do not go faster than 61 km/h (38 mph) when in this gear. You canupshift from 1 (First) to overdr...

Do not exceed the GVWR or the GAWR specified on thecertification label. Do not use replacement tires with lower load carrying capacities than theoriginals because they may lower the vehicle’s GVWR and GAWRlimitations. Replacement tires with a higher limit than the originals donot increase the GVWR a...

The amount of weight that you can tow depends on the type of engine inyour vehicle. See the following charts: 3.0L 2-Valve Vulcan Engine Model PassengerLoad - #/kg(lbs.) Luggage Load -kg (lbs.) Max TrailerWt.- kg (lbs.) Sedan 5/340 (750) 0 365 (800) 4/270 (600) 70 (150) 365 (800) 2/135 (300) 70 (150...

Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control mayshut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower...

RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as behind arecreational vehicle). These guidelines are designed to ensure that your transmission is notdamaged due to insufficient lubrication. All Front W...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover. The fuses are coded as follows. Fuse/relay location Fuse a...

To reduce risk of electrical shock, always replace the cover tothe Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and specifications chapter. The high-current ...

3. If equipped with a wheel coverthat’s bolted on, loosen the fiveplastic nuts with the lug nutwrench. 4. Remove the center ornament or wheel cover from the wheel with thetapered end of the wheel lug nut wrench that came with your vehicle.Insert and twist the handle, then pry against the wheel. 5. L...

10. Remove the jack and fullytighten the lug nuts in the ordershown. 11. Return the flat tire, jack and lugwrench to their proper storagelocations. Make sure the jack isfastened so it does not rattle whenyou drive. 12. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around the battery can e...

Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the transmissionmay have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Ov...

4. Make the final connection of the negative (-) cable. Make theconnection to an exposed metal part of the stalled vehicle’s engine, awayfrom the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect t...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery. + – + – + – + – Roadside Emergencies 172

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a s...

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you return to the Ford dealerwhere your vehicle was purchased when warranty repairs are needed.However, you may also take your vehicle to another Ford ...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

What the Board needs To have your case reviewed you must complete the application in theDSB brochure and mail it to the address provided on the applicationform. Some states will require you to use certified mail, with returnreceipt requested. Your application is reviewed and, if it is determined to ...

Every effort is made to decide the case within 40 days of the date thatall requested information is received by the Board. Since the Boardgenerally meets once a month, it may take longer for the Board toconsider some cases. After a case is reviewed, the Board mails you a decision letter and aform on...

environment. These impartial arbitrators review the positions of theparties, make decisions and, when appropriate, render awards to resolvedisputes. CAMVAP decisions are fast, fair, and final; the arbitrator’saward is binding both to you and Ford of Canada. CAMVAP services are available in all terri...

ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATEDP.O. Box 07150Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Helm, incorporated can also be reached by their website:...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Detail Wash (ZC-3–A), which is available from yourdealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and spot painted...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

WINDOWS AND WIPER BLADES The windshield, rear window and wiper blades should be cleanedregularly. If the wiper does not wipe properly, substances on thewindshield, rear window or the wiper blades may be the cause. Thesemay include hot wax treatments used by commercial car washes, treesap, or other o...

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Extra Strength Upholstery Cleaner(E8AZ-19523–AA). • If grease or tar is present on the material, spot-clean the area f...

WOOD-TONE TRIM • Clean the area with a damp cloth, then dry by wiping with a dry, soft,clean cloth. • Do not use household or glass cleaners as these may damage thefinish. FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products availableto clean you...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

Working with the engine off 1. Set the parking brake, and ensure the gearshift is securely latched in(P) park. 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on 1. Set the parking brake and ensure the gearshift ...

3.0L DOHC V6 Duratec engine 1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Engine oil dipstick 6. Engine oil filler cap 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power steering fluid reservoir Maintenance and Specifica...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

Checking and adding washer fluid for the liftgate (if equipped) The opening for the reservoir islocated on the passenger side underthe tail lamp. Refill this reservoirwith the same fluid you use for yourwindshield. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the a...

5. Locate and carefully remove theengine oil indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the add 1QT and FULL marks or between the MIN and MAX marks (depending on application), the oil level is acceptable. DO NOT A...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

that does not meet Ford material and design specifications, start-upengine noises or knock may be experienced.It is recommended you use the appropriate Motorcraft oil filter (oranother brand meeting Ford specifications) for your engine application. BATTERY Your vehicle is equipped with aMotorcraft m...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant reservoir (depending uponapplication). • Refer to the Scheduled Maintenance Guide for service interval...

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. The cooling system in your vehicle is filled with either green-coloredMotorcraft Premium Engine Coolant meeting Ford specificationESE...

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when the engine is cool. Add the proper mixture of coolant andwater to the “cold full” level. For all other vehicles, which have a coolantdegas system wit...

Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolantproduced by Ford-approved processes in vehicles originally equippedwith Motorcraft Premium Engine Coolant (green-colored). However, notall coolant recycling processes produce coolant that meets Fordspecificatio...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuels such as gasoline and ethanol are highlytoxic an...

• DO NOT use a device that would hold the fuel pump handle in the fillposition. Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until itst...

Fuel quality Many of the world’s automakersissued the World-wide Fuel Charterthat recommends gasolinespecifications to provide improvedperformance and emission controlsystem protection for your vehicle.Gasolines that meet the World-wideFuel Charter should be used whenavailable. Ask your fuel supplie...

Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverseaffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ...

Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter. The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated ca...

5. Follow one of the simple calculations in order to determine fueleconomy: Multiply liters used by 100, then divide by total kilometerstraveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (cityor highway). This will provide...

Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended engine oil. Refer to Lubricant specifications in this chapter. • Perform all regularly scheduled maintenance items. Follow there...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may n...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

However, the fluid level should be checked if the transaxle is not workingproperly, i.e., if the transaxle slips or shifts slowly or if you notice somesign of fluid leakage. Automatic transmission fluid expands when warmed. To obtain anaccurate fluid check, drive the vehicle until it is warmed up(ap...

High fluid level Fluid levels above the safe rangemay result in transaxle failure. Anoverfill condition of transmissionfluid may cause shift and/orengagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Be...

The temperature grade for this tire is established for a tire thatis properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or incombination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Us...

Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification or Tire Label. Make sure that all tires are the same size,speed rat...

3 If a spark plug is to be removed for inspection, it must be reinstalled in the same cylinder. If a spark plug needs to be replaced, use only sparkplugs with the service part number suffix letter as shown on the enginedecal. REFILL CAPACITIES Fluid Ford PartName Application Capacity Brake fluid Mot...

Items Ford PartName orequivalent Ford PartNumber FordSpecification Lock cylinders Penetrating andLock Lubricant Motorcraft XL-1 none Automatictransaxle (AX4Sand 4F50N 1 ) MotorcraftMERCON t V ATF XT-5-QM MERCON t V Engine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil XO-5W20-QSP WSS-M2C153...

Vehicle identification number The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) 1. World manufacturer identifier 2. Brake type and gross vehiclewei...

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincoln Mercury or Ford ofCanada dealer. These quality accessories have been specificallyengineered to fulfill your automotive needs; they are custom desig...

A ABS (see Brakes) .....................140 Accessory delay ..........................70 Air bag supplemental restraintsystem ........................117–118, 121 and child safety seats ............119description ......................118, 121disposal ....................................123driver ai...

Engine oil ..................................195 checking and adding ..............195dipstick ....................................195filter, specifications ........197, 224recommendations ...................197refill capacities ........................225specifications ..................226, 228 Ex...