Ford 2002 Explorer v.3- User Manual

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Service engine soon Illuminates briefly to ensure thesystem is functional. If it comes onafter the engine is started, one ofthe engine’s emission controlsystems may be malfunctioning. Thelight may illuminate without ad...

Light turns on solid: Temporary malfunctions may cause the light to illuminate. Examples are: 1. The vehicle has run out of fuel. 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securelytightened. These temporary malfunctions can be corrected by fi...

Air bag readiness Illuminates to confirm that the airbags (front or side) are operational.If the light fails to illuminate,continues to flash or remains on,have the system servicedimmediately. Safety belt Illuminates to remind you to fastenyour safety belts. For moreinformation, refer to the Seating...

Turn signal Illuminates when the turn signals orthe hazard lights are turned on. Ifthe lights stay on continuously orflash faster, check for a burned-outbulb. High beams Illuminates when the high beamheadlamps are turned on. Anti-theft system (if equipped) Refer to Perimeter alarm system (if equippe...

Door ajar Illuminates when any door is open(or not fully closed). O/D off (if equipped) Illuminates when the overdrivefunction has been turned OFF usingthe Transmission Control Switch(TCS) on end of gearshift. If thelight does not come on or the light flashes steadily, have your vehicleserviced as s...

Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (theindicated area between the “H” and“C”). If it enters the red section, theengine is overheatin...

• Optional instrument cluster Refer to Message Center in this section for information on how to switch the display from metric to English measurements. Trip odometer Registers the kilometers (miles) of individual journeys. • Standard instrument cluster Press and release the select/resetbutton to tog...

Battery voltage gauge Indicates battery voltage. If thepointer moves and stays outside thenormal operating range (asindicated by the arrows), have thevehicle’s electrical system checkedas soon as possible. Engine oil pressure gauge Indicates engine oil pressure. Atnormal operating temperature, thene...

Fuel gauge Displays approximately how muchfuel is in the fuel tank. The fuelgauge may vary slightly when thevehicle is in motion or on a grade. When refueling the vehicle fromempty indication, the amount of fuelthat can be added will be less thanthe advertised capacity due to thereserve fuel. The FU...

Compass zone adjustment 1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap. 2. Turn ignition to the ON position. 3. Locate compass sensor mountedat base of mirror. 4. Insert a paperclip into the smallhole on the bottom of the compasssensor. Hold down u...

Compass calibration adjustment Perform this adjustment in an open area free from steel structures andhigh voltage lines: For optimum calibration, turn off all electrical accessories (heater/airconditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the vehicle. 2. Locate compa...

Selectable features Reset Press this control to select and resetfunctions shown in the INFO menuand SETUP menu. Info menu This control displays the followingcontrol displays: • Odometer/Compass • Trip odometer/Odometer/Compass • Distance to Empty • Average Fuel Economy Odometer/Trip odometer Refer t...

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegrees between adjacent zones and will become noticeable as thevehicle crosses multiple zones. A correct zone setting will eliminate thiserror. Refer to ...

It is important to press the RESET control after setting the speedcontrol to get accurate highway fuel economy readings. DISTANCE TO EMPTY (DTE) Selecting this function from theINFO menu will give you anestimate of how far you can drivewith the fuel remaining in your tankunder normal driving conditi...

3. Press and hold the RESETcontrol to set the language choice. Units (English/Metric) 1. Select this function from theSETUP menu for the current unitsto be displayed. 2. Press the RESET control tochange from English to Metric. System check Selecting this function from theSETUP menu causes the messag...

CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessorieswhen the engine is idling at a low speed, turn off as many of theelectrical loads as soon as possible. If the warning stays on or comes onwhen the engine is opera...

LOW WASHER FLUID LEVEL. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and care chapter. DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic...

HEADLAMP CONTROL Rotate the headlamp controlclockwise to the first position toturn on the parking lamps. Rotateclockwise to the second position toalso turn on the headlamps. Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on only when the headl...

High beams • Push forward to activate. • Pull toward you to deactivate. Flash to pass Pull toward you to activate andrelease to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate up to brighten. • Rotate down to dim. •...

AUTOLAMP CONTROL The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control. The autolamp system also keeps thelights on for approximately 20seconds after the ignition switch isturned to OFF. • To turn autolamps on, rotate th...

If the vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of...

Mode selector control Controls the direction of the airflowto the inside of the vehicle. The air conditioning can operate in all modes. However, the airconditioning will only function if the outside temperature is about 6°C(43°F) or higher. Since the air conditioner removes considerable moisture fro...

• (Floor)-Distributes outside air through the floor ducts. Heating and air conditioning capabilities are provided in this mode. Push theA/C control in order to cool the vehicle below the outsidetemperature. • (Floor and defrost)-Distributes outside air through the windshield defroster ducts and the ...

During periods of high humidity, vapor may be emitted from the airoutlets when using the A/C system with outside air. This can becorrected by using MAX A/C to cool the vehicle. • A/C control This control is used to manually enable or disable the operation of theair conditioning in all modes except ,...

Dual Electronic Automatic Temperature Control (DEATC) system(if equipped) The Dual Electronic Automatic Temperature Control (DEATC) systemwill maintain a selected temperature and automatically control air flow. You can override the automatic operation with any of the overridecontrols. The dual tempe...

In and , if the outside temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reducefogging. However, the A/C indicator will be off and the A/C overridecontrol cannot be selected. The air conditioning compressor can operate in all modes except OFF.Ho...

When AUTO is selected, the recirculated air feature operatesautomatically for existing conditions. However, the air recirculationindicator will not be lit. If the recirculated air is selected while in AUTOoperation, the DEATC system will be disabled and you will return tomanual operation with the re...

(floor/defrost) — Distributes outside air through the windshield defroster ducts, the demister outlets and the front and rear seat floorducts. If the temperature is about 6°C (43°F) or higher, the airconditioner will automatically dehumidify the air to reduce fogging.(Note that the A/C indicator doe...

for 4 seconds. Following this, the outside temperature display will returnto the window. If the outside temperature is displayed while the DEATC system is in theOFF mode and the DEATC is turned on, the driver and passengertemperatures will be displayed for 4 seconds. Following this, the outsidetempe...

Front auxiliary control For the rear auxiliary climatecontrols to function, the frontauxiliary climate control must be setto REAR. To control the auxiliary climatecontrol system from the frontcontrols, turn the fan speed controlknob to the desired speed. Turn the temperature control toregulate the a...

Rear auxiliary climate controls (if equipped) The rear auxiliary climate controlsare located in the headliner of thesecond row seating. Ensure that the front auxiliarycontrol is turned to REAR to enablethe rear climate controls. Turn the fan speed control to thedesired fan speed. Turn the temperatur...

Press the mode selector once toselect air distribution through theoverhead vents. The icon will illuminate on the temperatureselector. Press the mode selector again to select air distribution through the floorvents. The icon will illuminate on the temperature selector. Only the auxiliary control hea...

Mode selector control Controls the direction of the airflowto the rear of the vehicle. To select air flow from the panel registers of the console, slide thecontrol to . To select airflow from the registers of the floor console, slide the control to . To stop the air from flowing through the floor co...

4WD CONTROL This control operates the 4WD.Refer to the Driving chapter for more information. USING YOUR AUDIO SYSTEM AM/FM stereo cassette SCAN BASS TREB BAL FADE SIDE EJ REW FF 1 - 2 TAPE AMS VOL - PUSH ON SEEK TUNE AM FM CLK 1 2 3 4 5 6 FM1 ST Controls and features 53

Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM s...

Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through thefrequencies quickly. • Press to move to the next frequency up the band (whether or ...

Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held i...

Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Tape select • To enter tape mode while in radiomode, press the TAPE AMScontrol. BAL FADE TAPE AMS CLK Controls and...

Automatic Music Search The Automatic Music Search featureallows you to quickly locate thebeginning of the tape selectionbeing played or to skip to the nextselection. To activate the feature, momentarilydepress the TAPE AMS button.Then, press either REW (for thebeginning of the current selection) or ...

Eject function Press the control to stop and eject atape. Dolby T noise reduction Dolby t noise reduction operates only in tape mode. Dolby t noise reduction reduces the amount ofhiss and static during tape playback. Press the control to activate (and deactivate) Dolby t noise reduction. Dolby t noi...

To set the minute, press and holdthe CLK control and press theTUNE control: • to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode(radio station, stereo information, etc.) and clock display mode (time).When in clock mode, the media inform...

Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM s...

Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or...

Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. CD select • To begin CD play (if CD[s] areloaded), press the CD control.The first track of the disc willbegin playing. After that, CD playwill begin where it stopped last. Do not insert any promotional (odd shaped o...

Eject function Press the control to stop and eject aCD. Compression feature Compression adjust brings soft andloud CD passages together for amore consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature The shuffle feature operates in CDmode a...

Volume/power control Press the control to turn the audiosystem on or off. Audio power can also be turned onby pressing the AM/FM selectcontrol or the tape/CD selectcontrol. Audio power is turned offby using the volume/power control. Turn control to raise or lowervolume. If the volume is set above a ...

Autoset memory preset Autoset allows you to set strong radio stations without losing youroriginal manually set preset stations. This feature is helpful on tripswhen you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select co...

Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Press the FADE control then press: • to shift the sound to the front and • to shift the sound to the rear. Tape/CD select • To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,p...

Dolby T noise reduction Dolby t noise reduction operates in tape mode. Dolby t noise reduction reduces the amount of hiss andstatic during tape playback. Press the control to activate (and deactivate) the Dolby t noise reduction. Dolby t noise reduction is manufactured under license from Dolby t Lab...

Setting the clock To set the hour, press and hold theCLK control and press SEEK: • to decrease hours and • to increase hours. To set the minute, press and holdthe CLK control and press TUNE: • to decrease minutes and • to increase minutes. If your vehicle has a separate clock,(other than the digital...

The CLK control will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock display mode (time).When in clock mode, the mediainformation will display for 10seconds, when the radio is turnedon, and then revert to clockinformation. Any time that themedia is cha...

Premium AM/FM Stereo In Dash Six CD Radio Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when the...

AM/FM select The AM/FM select control works inradio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radi...

Radio station memory preset The radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stations and twelveFM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. Pr...

Menu mode The MENU control allows you toaccess many different featureswithin your audio system. There arethree sets of menus availabledepending upon which mode orfeature is activated. While in FM mode, two menus areavailable. If RDS is turned OFF , you can access the following: • SELECT HOURS — Refe...

Radio data system (RDS) feature This feature allows your audiosystem to receive text informationfrom RDS-equipped FM radiostations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS f...

Setting the clock Press the MENU control untilSELECT HOUR or SELECTMINUTE is displayed. (The menumode must be engaged to enableclock mode). Use the SEL control to manually setthe time. • Press to increase hours/minutes. • Press to decrease hours/minutes. Press the MENU control again to disengage the...

CD and CD changer care • Handle discs by their edges only. Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extendedperiods of time. • Do not insert more than one disc into each slot of the CD changermagazine. Do not insert any promotional (odd shaped or ...

Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km(24 miles). This range can be affected by “signal modulation.” Signalmodulation is a process...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off,the previously programmed setspeed will be erased. To set a speed • Press SET+. For speed control tooperate, the speed control mustbe ON and the vehicle speedmust be greater than 48 km/h(30 m...

To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (ifequipped). Disengaging the speed control willnot erase the previouslyprogrammed set speed. Pressing OFF will erase thepreviously programmed set speed. Controls and features 96

If your vehicle has the tilt-onlysteering column, pull the lever downto unlock the steering column. Whilethe lever is in the down position, tiltthe steering column to its desiredorientation. Lift the lever back to its originalposition to lock the steering column. Never adjust the steering column whe...

HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed position. The bars of varying length are forintermittent wipers. Wh...

STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate controlfeatures. Audio control features Press to select AM, FM1, FM2, TAPE, or CD (if equipped). In AM, FM1, or FM2 mode: • Press MEM to select presetstations within the selected radioband. In Tape mode:...

Climate control features Press TMP + or - to adjusttemperature. Press + or - to adjust fan speed. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment Press the latch to open the storagecompartment. Controls a...

Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers: • Place Velcro hook onto side ofaftermarket transmitter oppositeof the button. • Place the transmitter into storagecompartment, button down. • Place the ...

Interior Lamps Dome lamps and map lamps The front map/dome lamp is located overhead between the driver andthe passenger seats. If the vehicle is equipped with a moon roof or largeoverhead console, the map/dome lamp is located above the second rowseat. All vehicles are equipped with acargo lamp, whic...

3. Using both hands simultaneouslypress and hold the hand-heldtransmitter button and the desiredHomeLink t button. Do not release the buttons until step 4 has beencompleted. Some entry gates and garage dooropeners may require you to replacestep 3 with the procedure in the“Canadian Programing” sectio...

3. Press and release theprogrammed HomeLink t button. Press and release the HomeLink t button a second time to complete the training process. (Some garagedoor openers may require thisprocedure to be done a third timeto complete the training.) The 2nd or 3rd press from step 3will activate the door. T...

The previous device has now been erased and the new device can beactivated by pushing the HomeLink t button that has just been programmed. AUTOMATIC DIMMING REAR VIEW MIRROR The autolamp/automatic dimmingmirror is equipped with anautomatic dimming feature. Thisfeature will change from the normalstat...

POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. One touch down • Press AUTO completely down andrelease quickly. The driver’swindow will open fully. One touch down...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press the leftside of the control. Press the rightside to restore the window controls. Accessory delay With accessory delay, the window switches and audio...

POWER DOOR LOCK/UNLOCK INHIBIT If the interior trim switch does notoperate, see the Perimeter alarm system in this section for more details. LIFTGATE An additional power door lock can be accessed by opening the liftgate.The button is located either on the top of the left-hand quarter trimpanel under...

POWER SIDE VIEW MIRRORS The ignition must be in the ACC or ON position to adjust the power sideview mirrors. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish...

Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. CENTER CONSOLE Your vehicle may be equipped with avariety of console features. Theseinclude: • Utility compartment withcassette/compact disc storage • Auxiliary power point • Cupholder...

Rear console features The rear console may incorporatethe following features: • air vents • cupholders • rear power point POSITIVE RETENTION FLOOR MAT Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tolock in. Make sure that the mat doesnot in...

• To open the liftgate window,press the control on the remoteentry key fob or, with the liftgateunlocked, push the control buttonthe on the right side under the license plate lamp shield. • To open the liftgate, unlock theliftgate (with the power doorlocks, the remote entry or thekeyless entry pad) ...

CARGO COVER (IF EQUIPPED) Your vehicle may be equipped with a cargo area cover that covers theluggage compartment of your vehicle. To install the cover: Push both ends of the cover into thedepressions (right side first) in thetrim panels behind the second rowseat. To reduce the risk ofinjuries, the ...

5 passenger cover: 1. To open, push the button on the storage compartment to pop up theknob. 2. Turn knob counterclockwise to unlock and pull the storagecompartment open. 3. To close, follow steps 1 and 2 in reverse order. REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and wi...

Sounding a panic alarm Press this control to activate thealarm. The personal panic alarm will cyclethe horn and turn signals on/off plusilluminate the interior lights. To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON. Memory seat feature (if equipped) The remote entry...

Replacing lost transmitters If a remote transmitter has been lostand you would like to remove itfrom the vehicle’s memory, or youwould like to purchase additionalremote transmitters and have themprogrammed to your vehicle: • Take all your vehicle’s transmitters to your dealer forprogramming, or • Pe...

Illuminated entry The lamps illuminate when the remote entry system is used to unlockthe door(s). The system automatically turns off after 25 seconds or when the ignitionis turned to the ON or ACC position. The dome lamp control (ifequipped) must not be set to the OFF position for the illuminated en...

Programming your own personal entry code 1. Enter the factory-set code (keypad will illuminate when pressed). 2. Press the 1/2 control within fiveseconds of step 1. 3. Enter your personal 5 digit code.Enter each digit within five secondsof the previous one. Do not set a code that includesthree of th...

If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds ofstep 1 and release. 3. Press the 1/2 control and hold for2 seconds to erase the customerprogrammed keycode, within fiveseconds of step 2. T...

Locking the doors and liftgate, pressthe 7/8 and 9/0 controls at the sametime. This can be done only whenthe driver’s door is closed. Autolock The autolock feature will lock all of the vehicle doors when: • all doors are closed • the engine is running and • you shift into any gear putting the vehicl...

Power door unlock/lockprocedure You must complete steps 1-5 within30 seconds or the procedure willhave to be repeated. If theprocedure needs to be repeated,you must wait 30 seconds. 1. Turn the ignition key to ON. 2. Press the power door unlock control three times. 3. Turn the ignition key from ON t...

Smart unlock This feature prevents the driver’s from locking while the key is in theignition. This feature will unlock only the driver’s door if the key is in theignition cylinder, the driver’s door is ajar and all doors are locked usingthe interior trim switch. If these conditions are met, the enti...

Arming the system When armed, this system will help protect your vehicle fromunauthorized entry. When unauthorized entry occurs, the system willflash the headlamps and/or parking lamps, and will chirp the horn. The system is ready to arm whenever the key is removed from theignition. Any of the follo...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using yourremote entry transmitter. • Unlock the doors by using yourkeyless entry pad. • Unlock the driver’s door with a key. Turn the key full travel (towardthe front of the vehicle) to make sure t...

• Press the PANIC control on theremote entry transmitter. Thiswill only shut off the horn andparking lamps when the alarm issounding. The alarm system willstill be armed. • Press the liftgate window controlon the remote entry transmitter.The liftgate and liftgate windoware no longer armed, but thedo...

Automatic arming The vehicle is armed approximately15 seconds after switching theignition to the 2 (ACC) position.The THEFT light in the instrument cluster will flash every two secondswhen the vehicle is armed. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarm...

Large metallic objects, electronicdevices on the key chain that can beused to purchase gasoline or similaritems, or a second key on the samekey ring as the coded key may cause vehicle starting issues. Ifpresent, you need to keep theseobjects from touching the coded key while starting the engine. The...

accessible for timely implementation of each step in the procedure. If two previously programmed coded keys are not available, you mustbring your vehicle to your dealership to have the spare coded key(s)programmed. Please read and understand the entire procedure before you begin. 1. Insert the first...

SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which arevertically adjustable. The purpose of these head restraints is to help limithead motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restrain...

Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to reduce the risk ofinjuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

Using the manual lumbar support Turn the lumbar support controltoward the front of vehicle to movethe lumbar support forward formore direct support. Turn the lumbar support controltoward the rear of vehicle to movethe lumbar support back for lessdirect support. Heated seats (if equipped) To operate ...

To return the seat to the uprightposition: 1. Pull the handle down and lift theseatback toward the rear of thevehicle. 2. Rotate the seatback until youhear a click, locking it in the uprightposition. Adjusting the 2nd row seat for E-Z Entry (if equipped) The E-Z Entry seat allows for easier entry an...

3. To return the seat to a seatingposition, flip the seat into theupright position. 4. Make sure the seat is latched tothe floor. To exit the 3rd row seat, pull thered access control lever up releasingthe seat from the floor and rotatethe seat up towards the front seat. Always latch the vehicle seat...

Folding the middle 2nd row seat (If equipped) 1. Locate the lever on the side ofthe seatback. 2. Pull the lever up and push theseatback toward the front of thevehicle. 3. Press down on the top outboardarea of the seatback until a click isheard. To return the seatback to theupright position: 1. Pull ...

Third row seat (if equipped) 3rd row stow feature The 3rd row seat has a tip/stow feature to increase cargo space withoutremoving the seat from the vehicle. To put seat in stowed position: 1. Pull the seat release lever locatedon top of the seatback whilepushing the seatback down onto theseat cushio...

2. Pull the seat release lever locatedon top of the seatback while liftingthe seatback into the uprightposition. 3. The seatback will latch into place. The third row seat is equipped with combination lap and shoulder beltsin both seating positions. For information on the proper operation of thesafet...

It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people toride in any area of your vehicle that is not equipped with seats andsafety belts. Be sure everyone i...

After any vehicle collision, the seat belt system at all passengerseating positions must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats isstill functioning properly. In addition, all seat belts should be checkedfor proper function. BELT ...

The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatoutboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing freesho...

• Grasp the shoulder portion andpull downward until the entirebelt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Disconnect the combinatio...

Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around thehips, not across the waist. • 2nd row center seatingposition — 60/40 The lap belt does not adjust automatically. Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is...

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andfront passenger seating positions. The safety belt pretensioners are designed to activate only when thesafety belts are fastened during certain frontal or near-frontal collisionswith sufficient longitud...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8seconds. The driver’s safety belt is buckledwhile the indicator light isilluminat...

One time disable Any time the safety belt is buckled and then unbuckled during anignition ON cycle, BeltMinder will be disabled for that ignition cycle only. Deactivating/activating the BeltMinder feature Read steps 1 - 9 thoroughly before proceeding with thedeactivation/activation programming proce...

6. Within seven seconds of the safety belt warning light turning off,buckle then unbuckle the safety belt. • This will disable BeltMinder if it is currently enabled, or enableBeltMinder if it is currently disabled. 7. Confirmation of disabling BeltMinder is provided by flashing the safetybelt warnin...

Modifications to the front end of the vehicle, including frame,bumper, front end body structure and non-Ford tow hooks may effect the performance of the air bag sensors increasing the risk ofinjury. Do not modify the front end of the vehicle. Additional equipment may affect the performance of the ai...

How does the air bag supplemental restraint system work? The air bag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbag inflation. The fact that the air bags did notinflate in a collision do...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS ...

If any of these things happen, even intermittently, have the SRS servicedat your dealership or by a qualified technician immediately. Unlessserviced, the system may not function properly in the event of acollision. Side air curtain system (if equipped) Do not attempt to service, repair, or modify th...

How does the side air curtain system work? The side air curtain system consistsof the following: • An inflatable nylon curtain with agas generator concealed behindthe headliner and above thedoors. • The headliner will flex to openabove the side doors to allow aircurtain deployment. • The same warnin...

Several air bag systemcomponents get hot after inflation. Do not touch them afterinflation. If the side air curtain hasdeployed, the air curtain will not function again. Theside air curtain system(including the A, B and Cpillar trim) must be inspectedand serviced by a qualifiedtechnician in accordan...

Disposal of air bags and air bag equipped vehicles(including pretensioners) For disposal of air bags or air bag equipped vehicles, see your localdealership or qualified technician. Air bags MUST BE disposed of byqualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for direc...

Installing child safety seats in combination lap and shoulder beltseating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all theway back. 1...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly tilt the seat forwardand back to...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equipment standardrequirements regulating the impulse electrical field strength of radionoise. When starting a fuel-injected engine, avoid pressing the a...

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE Note: Whenever you start your vehicle, release the key as soon as the engine sta...

Cold weather starting (flexible fuel vehicles only) As the outside temperature approaches freezing, ethanol fuel distributorsshould supply winter grade ethanol (same as with unleaded gasoline). Ifsummer grade ethanol is used in cold weather conditions, you mayexperience increased cranking times, rou...

BRAKES Your service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or int...

ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does notilluminate momentarily at start up, remains on or continues to flash, theABS needs to be serviced. With the ABS light on, the anti-lockbrak...

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released. Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual t...

Do not drive your vehicle until you verify that the brakelampsare working. If your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping between shifts, in asteady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle ...

Understanding gearshift positions Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) To put your vehicle in gear, start the engine, depress the brake p...

2 (Second) Use 2 (Second) to start-up onslippery roads or to provideadditional engine braking ondowngrades. 1 (First) Use 1 (First) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higherspeeds causes the trans...

Driving a manual transmission (if equipped) Using the clutch Vehicles equipped with a manualtransmission have a starter interlockthat prevents starting the engineunless the clutch pedal is fullydepressed. When starting a vehicle with amanual transmission: 1. Hold down the brake pedal. 2. Put the gea...

2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Recommended shift speeds Upshifts when accelerating (recommended for best fuel econo...

Upshifts when cruising (recommended for best fuel economy) Shift from: Transfer case position (if equipped) AUTO or HIGH LOW 1 - 2 16 km/h (10 mph) 6 km/h (4 mph) 2 - 3 26 km/h (16 mph) 10 km/h (6 mph) 3 - 4 43 km/h (27 mph) 16 km/h (10 mph) 4 - 5 (Overdrive) 68 km/h (42 mph) 26 km/h (16 mph) Maximu...

4x4 High and 4x4 Low operation is not recommended on drypavement. Doing so could result in difficult disengagement of thetransfer case, increased tire wear and decreased fuel economy. Control-Trac automatic four-wheel drive system (if equipped) The 4WD system uses all four wheels to power the vehicl...

Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily underoff-road conditions. Avoid sharp turns or abrupt maneuvers in thesevehicles. Positions of the Control-Trac system T...

• The 4x4 Low mode suppliesfour-wheel drive with full powerto both axles and includes alower gear ratio for low-speed. Itis only intended for off-roadapplications that require extrapower including deep sand, steepgrades and pulling a boat andtrailer out of the water. The vehicle should not be operat...

Using the Control-Trac system Shifting between 4x4 Auto and 4x4 High When you press the 4x4 Highbutton, the indicator light willilluminate in the instrument cluster.When you press the 4x4 Autobutton, the indicator light will turnoff. Either shift can be done at a stop orwhile driving at any speed. S...

Shifting from 4x4 Low to 4x4 Auto or 4x4 High 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral)(automatic transmission) or depressthe clutch (manual transmission). 4. Press the 4x4 Auto or the 4x4High button. When 4x4 Auto isengaged NO indicator lights willi...

Power is supplied to all four wheelsthrough a transfer case. On 4WDvehicles, the transfer case allowsyou to select 4WD when necessary.Information on transfer caseoperation and shifting procedurescan be found in the Driving chapter. Information on transfercase maintenance can be found in the Maintena...

Once through water, always try the brakes. Wet brakes do not stop thevehicle as effectively as dry brakes. Drying can be improved by movingyour vehicle slowly while applying light pressure on the brake pedal. Be cautious of sudden changes in vehicle speed or direction when youare driving in mud. Eve...

When climbing a steep slope or hill,start in a lower gear rather thandownshifting to a lower gear from ahigher gear once the ascent hasstarted. This reduces strain on theengine and the possibility of stalling. If you do stall out, do not try toturn around because you might rollover. It is better to ...

Avoid sudden braking as well. Although a 4WD vehicle may acceleratebetter than a two-wheel drive vehicle in snow and ice, it won’t stop anyfaster, because as in other vehicles, braking occurs at all four wheels. Donot become overconfident as to road conditions. Make sure you allow sufficient distanc...

These “aftermarket lift kits” could adversely affect the vehicle’s handlingcharacteristics, which could lead to loss of vehicle control or roll overand serious injury. Tires can be damaged during off-road use. For your safety, tires that aredamaged should not be used for highway driving because they...

Any modifications to a vehicle that raise the center of gravity can makeit more likely the vehicle will roll over as a result of a loss of control.Ford recommends that caution be used with any vehicle equipped with ahigh load or device (such as ladder racks or pickup box cover). Failure to maintain ...

Always ensure that the weight of occupants, cargo and equipment beingcarried is within the weight limitations that have been established foryour vehicle including both gross vehicle weight and front and rear grossaxle weight rating limits. Under no circumstance should these limitationsbe exceeded. E...

DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth isunknown. Traction or brake capability may be limited and if the ignitionsystem gets wet, your engine may stall. Water may also enter yourengine’s air intake and severely damage your engine. If driving throug...

Do not exceed the maximum loads listed on the Safety ComplianceCertification label. For load specification terms found on the label, referto Vehicle loading in this chapter. Remember to figure in the tongue load of your loaded vehicle when figuring the total weight. Your vehicle is equipped with a s...

4x4 w/automatic transmission *-When towing maximum loads under high outside temperatures and/oron steep grades, the A/C system may cycle on and off to protect theengine from overheating. This may result in a temporary increase ofinterior temperatures. Towing a trailer over 1 588 kg (3 500 lbs.) requ...

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The trailer brakes must meet local and Federalregulations. Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s bra...

Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance guide formore information. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the veh...

Recreational towing (all wheels on the ground) Follow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as behind arecreational vehicle). These guidelines are designed to ensure that your transmission is notdamaged due to insufficie...

LUGGAGE RACK Your vehicle is equipped with a roofrack. The maximum recommendedload is 90 kg (200 lbs), evenlydistributed. If it is not possible todistribute the load, position it as farrearward as possible. Use the tiedown loops on the thumbwheels (ifequipped) to secure the load. To adjust cross-bar...

Getting roadside assistance To fully assist if you should have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty peri...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located below theinstrument panel on the driver’sside. To remove a fuse use the fuse puller tool provided on the fuse panel box. The fuses are coded as follows: 1 6 16 21 26 27 28 29 30 22 23 24 25 17 18 19 20 7 8 9 10 11 12 13 14 15 2 3 4 5 Roadsid...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 25 5A Mode, Temperature Actuator, AuxiliaryClimate Control, Trailer Tow BatteryCharge 26 7.5A Park Aid, Brake Shift Interlock, ApproachLamp Relay Coil 27 7.5A Electrochromatic Mirror, Security Module,Digital Transmissio...

Passenger compartment fuse panel (top side) These relays are located on the reverse side of the passengercompartment fuse panel. To access the relays you must remove thepassenger compartment fuse panel. Fuse/Relay Location Description Relay 1 Flasher Relay Relay 2 Rear Defrost Relay 3 Delayed Access...

Power distribution box The power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protect yourvehicle’s main electrical systemsfrom overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electrical...

Auxiliary relay box (trailer tow) The relay box is located on the frontright fender well underneath thespeed control module. The relays are coded as follows: Fuse/Relay Location Description Relay 64 Trailer Tow (Left turn) Relay 65 Trailer Tow (Right turn) Relay 66 Not Used CHANGING THE TIRES If you...

Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the followinglocations: Tool Location Spare tire Under the vehicle, just in front ofthe rear bumper. The Spare TireWinch Drive Nut is located at therear center of the cargo areaunder a lid. Jack, lug nut wre...

Removing the spare tire Do not use an impact wrench onthe winch drive nut. This willdamage the spare tire winch 1. Open the cover from thecarpeting on cargo floor to exposethe winch drive nut. 2. Insert the lug wrench on thewinch drive nut. The wrench will stop moving andforward resistance to turnin...

Tire change procedure To prevent the vehicle from moving when you change a tire, besure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) tothe tire being changed. If the vehicle slips off the jack, you or someone else...

11. Remove the jack and fullytighten the lug nuts in the ordershown. 12. Replace beauty cap, stow thejack and tools in their respectivelocations, making sure they are fullysecured so they do not rattle whenyou drive. 13. Unblock the wheels. Stowing the spare tire 1. Lay the tire on the ground with t...

Do not attempt to push-start your vehicle. Automatictransmissions do not have push-start capability; also, thecatalytic conveter may become damaged. Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its adaptive strategy. As a result ...

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to the providedjumpstarting bolt ONLY. Connecting to...

5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicl...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

• Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on • Automatic transmission: 1. Set the parking brake a...

OPENING THE HOOD 1. Inside the vehicle, pull the hood(rearward) release handle locatedunder the bottom left corner of theinstrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that islocated under the front center of the hood. 3. Lift the hood. Maintenance and care 250

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Power distribution box 6. Battery 7. Power steering fluid reservoir 8. Air filter assembly 9. Windshield washer fluid reservoir...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

• 4.6L V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the levelwithin the MIN-MAX range. Mainte...

• 4.0L SOHC V6 engine • 4.6L V8 engine • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Maintenance and care 255

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

4.0L Engine Look for this certificationtrademark. SAE 5W-30 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). Use Motorcraft or an equivalent oil meetingFord Specification WSS-M2C153–G. Do not use supplemental engine oil additives, oi...

BRAKE FLUID AND CLUTCH FLUID Checking and adding brake fluid/clutch fluid When equipped with a manualtransmission, your vehicle uses thesame reservoir for brake and clutchfluid. Brake/clutch fluid should bechecked and refilled as needed.Refer to the scheduled maintenanceguide for the service interva...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

coolant reservoir. If the level falls below, add coolant per the instructionsin the Adding Engine Coolant section. Your vehicle was factory-filled with a 50/50 engine coolant and waterconcentration. If the concentration of coolant falls below 40% or above60%, the engine parts could become damaged or...

If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not u...

• A large amount of water without engine coolant may be added, in caseof emergency, to reach a vehicle service location. In this instance, thecooling system must be drained and refilled with a 50/50 mixture ofengine coolant and distilled water as soon as possible. Water alone(without engine coolant)...

6. Replace the cap. Turn until tightly installed. (Cap must be tightlyinstalled to prevent coolant loss.) After any coolant has been added, check the coolant concentration seeChecking Engine Coolant section). If the concentration is not 50/50(protection to –34° F/–36° C), drain some coolant and adju...

Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]), itmay be necessary to increase the coolant concentration above 50%.Refer to the chart on the coolant container to ensure the coolantconcentration in your vehicle will provide adequate freeze protection. Never increa...

Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase. Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage. When fa...

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules. If adding fluid is necessary, useonly MERCON t ATF. • 4.0L SOHC V6 engine • 4.6L V8 engine 1. Start the engine and let it run until it reaches normal o...

4. Fluid level should be at bottom ofthe opening. 5. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 6. Install and tighten the fill plugsecurely. Use only fluid that meets Ford specifications. Refer to the Refill capacities in this chapter. CHECKIN...

3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to Refill Capacities in the Capacities and specifications chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with ...

mineral or alkali content). If possible, however, try to only fill the batterycells with distilled water. If the battery needs water often, have thecharging system checked. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trou...

Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe battery is disconnected or a new battery is installed, the engine mustrelearn its idle and fuel trim strategy for optimum driveability andperformance. To...

WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem lesseffective. Substances such as tree sap and some hot wax treatments usedby commercial car washes reduce the effectiveness of wiper blades. Checking the wiper blades If the wiper blades do not wipe properly, cle...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing thetire’s resistance to the gen...

Tire rotation Because your vehicle’s tires perform different jobs, they often weardifferently. To make sure your tires wear evenly and last longer, rotatethem as indicated in the scheduled maintenance guide. If you notice thatthe tires wear unevenly, have them checked. • Four tire rotation • Five ti...

Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speedrating, and...

USING SNOW TIRES AND TRACTION DEVICES Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all-weather treads to provide traction inrain and snow. However, in some climates, using snow tires or tractiondevices may be necessary. For...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuels suchas gasoline and ethanol are highlytoxic and...

The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO N...

Running out of fuel Avoid running out of fuel because this situation may have an adverseaffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling, to allow the fuel system to pump the fuel from the tank tothe engine...

For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling,an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than 2...

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to changea number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually gi...

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may reduce fuel economy (approximately0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bugdefl...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your “Check Engine/Service EngineSoon” light is on, refer to the description in the Warning lights and chimes section of the Instrumentation ...

Replacing headlamp bulbs The high beam and low beam bulbs are located in the headlampassembly. Follow the same steps to replace either bulb: To remove the headlamp bulb: 1. Make sure headlamp switch is inOFF position, then open the hood. 2. At the back of the headlamp, pryup the two retainer pins un...

To install the new bulb: Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb tobreak the next time the headlamps are operated. If the bulb is accidentally touched, it...

4. Rotate bulb socketcounterclockwise and remove fromlamp assembly. 5. Carefully pull bulb straight out ofsocket and push in the new bulb. 6. Install bulb socket in lampassembly by turning clockwise. 7. Align the parking lamp studs withthe plastic grommets on the vehicle and push rearward to snap in...

Replacing foglamp bulbs 1. Reach under the front bumperand remove the bulb socket fromthe foglamp by turningcounterclockwise. 2. Disconnect the electricalconnector from the foglamp bulb. 3. Connect the electrical connectorto the new foglamp bulb. 4. Install the bulb socket in the foglamp turning clo...

2. Remove the bulb holder from thelamp assembly by depressing thesnaps. 3. Pull the bulb straight out of thesocket and push in the new bulb. To complete installation, follow theremoval procedure in reverse order. USING THE RIGHT BULBS Replacement bulbs are specified in the chart below. Headlamp bulb...

2. Measure the height from the center of your headlamp to the groundand mark a 2.4 meter (8 foot) horizontal reference line on the verticalwall or screen at this height (a piece of masking tape works well). Thecenter of the lamp is marked by a 3.0 mm circle on the headlamp lens. 3. Turn on the low b...

Washing your vehicle Wash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty, use aquality car wash detergent. Alwaysuse a clean sponge, washing gloveor similar device and plenty of waterfor best results. To avoid spots,avoid w...

• Cover the highlighted areas to prevent water damage when cleaningthe engine. 4.6L V8 Engine 4.0L SOHC V6 Engine Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not useacid-based or alcohol-based wheel cleaners, steel wool, fuel or strongdetergents. Never use abrasi...

The brushes used in some automatic car washes may damage the finishon your wheels. Before going to a car wash, find out if the brushes areabrasive. Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover ifnecessary. Do not clean plastic parts wit...

Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination of the air bag system. Cleaning the instrument cluster lens Clean with a damp cloth, then dry with a dry cloth. Do not use household or glass cleaners as these may damage the ...

MOTORCRAFT PART NUMBERS Component 4.0L SOHC V6 engine 4.6L V8 engine Air filter element FA-1695 FA-1695 Fuel filter FG-986B FG-986B Battery BXT-65-650 BXT-65-650 Oil filter FL-820S FL-820S PCV valve EV-243 F6ZE-6C324-CA Spark plugs* AGSF-22PP ** AWSF-32P * Refer to Vehicle Emissions Control Informat...

Item Ford PartName orequivalent Ford PartNumber FordSpecification 4.6L Engine oil Motorcraft SAE5W20 SuperPremium MotorOil XO -5W20-QSP WSS-M2C153-Hwith APICertificationMark Automatictransmission 1 MotorcraftMERCON t V ATF XT-5-QM MERCON t V Power steeringfluid MotorcraftMERCON t Multi-PurposeATF XT...

* Height includes roof rack and P235 tire 1 4 2 5 3 Capacities and specifications 311

1. World manufacturer identifier 2. Brake type and gross vehicleweight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identificationnum...

Ford Extended Service Plan You can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESPis an optional service contract which is backed by Ford Motor Companyor Ford Motor Service Company (in the U.S.) and Ford of Canada (inCanada). ...

taken to another dealer. If a particular dealership can not assist you,then contact the Customer Relationship Center. If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at yourselling/se...

THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Companyvehicles The Dispute Settlement Board may not be available in all states. FordMotor...

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Busi...

Trailer hitch (Class III) Trailer hitch bars and balls Trailer hitch mount bike carrier Trailer hitch receiver cover Trailer hitch wiring adaptor Protection and appearance equipment Air bag anti-theft locks Cargo liners, interior Carpet floor mats Cleaners, waxes and polishes Door edge guards Front ...

For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight capacity of the vehicle or ofthe front or rear axle (GVWR or GAWR a...

Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing toFord Motor Company of Canada, Limited, Service Publications, P.O. Box1580, Station B, Mississauga, Ontario L4Y 4G3. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that,...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect which could cause a crash,or could cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar comp...

A Accessory delay ........................111 Air bag supplementalrestraint system ................162, 167 and child safety seats ............164description ......................162, 167disposal ....................................170driver air bag ..................165, 168indicator light ..........

Driving underspecial conditions .............203, 206 sand .........................................205snow and ice ...........................207through water .................205, 213 E Electronic message center .........19 Emergencies, roadside jump-starting ..........................241 Emission...

battery voltage gauge ...............16engine coolanttemperature gauge ...................14engine oil pressure gauge ........16fuel gauge ..................................17odometer ...................................14speedometer .............................14tachometer ............................

Parking brake ............................185 Parts (see Motorcraft parts) ....304 Pedals (see Poweradjustable foot pedals) ...............31 Power distribution box(see Fuses) ...............................230 Power door locks ......................111 Power steering ..........................186 f...

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 85.2L (22.5 gallons) 4.0L Engine oil capacity(includes filter change) 4.7L (5.0 quarts). Use MotorcraftSAE 5W-30 Super Premium MotorOil, Ford specificationWSS-M2C153-G. 4.6L Engine oil capacity(includes filter change) 5...