Ford 2001 Taurus- User Manual

Headlamp control (pg. 17) Instrument panel dimmer control (pg. 18) Instrument cluster (pg. 8) Driver air bag (pg. 104) Turn signal and wiper/washer control (pg. 56) Parking brake release (pg. 129) Rear window wiper and washer — wagon only* (pg. 57) Trunk release — sedan only (pg. 66) * if equipped I...

WARNING LIGHTS AND CHIMES Turn signal Illuminates when the left or rightturn signal or the hazard lights areturned on. If one or both of theindicators stay on continuously orflash faster, check for a burned-outturn signal bulb. Refer to Bulbs in the Maintenance and care chapter. High beams Illuminat...

Safety belt Momentarily illuminates when theignition is turned to the ON positionto remind you to fasten your safetybelts. For more information, refer tothe Seating and safety restraints chapter. Door ajar Illuminates when the ignition is inthe ON position and any door isopen. It may also momentaril...

Service engine soon Your vehicle is equipped with acomputer that monitors the engine’semission control system. Thissystem is commonly known as theOn Board Diagnostics System (OBD II). The OBD II system protects theenvironment by ensuring that your vehicle continues to meetgovernment emission standar...

Light is blinking: Engine misfire is occurring which could damage your catalytic converter.You should drive in a moderate fashion (avoid heavy acceleration anddeceleration) and have your vehicle serviced at the first availableopportunity. Under engine misfire conditions, excessive exhaust temperatur...

Anti-lock brake system (ABS) (If equipped) Momentarily illuminates when theignition is turned to the ON positionto ensure the circuit is functional. Ifthe light does not illuminatemomentarily at start up, remains onor continues to flash, the ABS needs to be serviced. With the ABS lighton, the anti-l...

Engine oil pressure Momentarily illuminates when theignition is turned to the ON positionand the engine is off. Illuminateswhen the oil pressure falls below thenormal range. Stop the vehicle assoon as safely possible and switch off the engine immediately. Check theoil level and add oil if needed. Re...

Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACCposition and the driver’s door is opened. Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off(and the key is not in the ignition) and the driver’s door is ope...

Tachometer Indicates the engine speed inrevolutions per minute. Driving with your tachometerpointer continuously at the top ofthe scale may damage the engine. Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlamps. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position an...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (pastdetent) to turn on interior lamps. • Rotate to full down position (past detent) to turn off interior lamps....

The defroster turns off automatically after 10 minutes or when theignition is turned to the OFF position. To manually turn off the defrosterbefore 10 minutes have passed, push the control again. Activating the rear window defroster will also activate the heated mirrors(if equipped). For more informa...

Mode selector control Controls the direction of the airflowto the inside of the vehicle. The air conditioning compressor canoperate in all modes except . However, the air conditioning willonly function if the outsidetemperature is about 6°C (43°F) orhigher. Since the air conditioner removes consider...

• (Floor and defrost)-Distributes outside air through the windshield defroster ducts and the floor ducts. Heating and air conditioningcapabilities are provided in this mode. For added customer comfort,when the temperature control knob is anywhere in between the fullhot and full cold positions, the a...

Turning the EATC on Press AUTO, any of the override controls or the fan speed control. TheEATC will only operate when the vehicle is running. Turning the EATC off Press OFF. The OutsideTemperature function will continueto operate until the ignition isturned off. Automatic operation Press AUTO and se...

Temperature selection The display window indicates theselected temperature, function(AUTO or one of the overridecontrols) and manual control of fanspeed ( ) if automatic fan speed is not desired. To control the temperature, selectany temperature between 18°C(65°F) and 29°C (85°F) by pressingthe temp...

Temperature conversion Press MAX A/C and F at the same time (until the display changes) to switch between Fahrenheit and Celsius. Fan speed ( ) When AUTO is pressed, fan speed isadjusted automatically for existingconditions. You can override fanspeed at any time. To control fanspeed manually, press ...

Manual override controls The override controls are located at the bottom of the EATC and allowyou to determine where airflow is directed. To return to full automaticcontrol, press AUTO. The air conditioning compressor can operate in all modes exceptand . It will also operate only when required when ...

• (Floor)-Allows for maximum heating by distributing outside air through the floor ducts. However, the air cannot be cooled below theoutside temperature because the air conditioning does not operate inthis mode. • (Panel and floor) -Distributes outside air through the instrument panel registers and ...

Operating tips • In humid weather conditions, place the climate control system inF before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate controlsystem as desired. • To reduce humidity buildup inside the vehicle in cold weathercondition...

• Do not place objects over the defroster outlets. These objects canblock airflow and reduce your ability to see through your windshield.Avoid placing small objects on top of the instrument panel. Theseobjects may fall down into the defroster outlets and block airflow, inaddition to damaging the cli...

USING YOUR AUDIO SYSTEM AM/FM Stereo Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. Controls and features 30

If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. If you wish to maintain your presetvolume level, turn the audio system off with the power control beforeswitching off the i...

Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Scan function The scan function works in radiomode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all l...

MACH T Audio System with AM/FM Stereo/Cassette Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when th...

AM/FM select The AM/FM select control works inradio, tape and CD modes (ifequipped). Press the AM or FMcontrol to enter into radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. Pr...

Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on theCD. (The CD scans in a forward direction, wrapping back to the firsttrack at the end of the CD.) To stop on a particular selection, press thecontrol again. Radio station memory preset The radio is equipp...

Audio System with AM/FM Stereo/Single CD Player Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when t...

Setting memory preset stations 1. Select the frequency band withthe AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memory...

CD changer (if equipped) Your CD changer is either located in the trunk, the console or the rightside cargo area storage compartment. 1. Slide the door to access the CDchanger magazine. 2. Press to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder releaseknob (C), pull the ...

• Do not insert more than one disc into each slot of the CD changermagazine. Do not insert any promotional (odd shaped or sized) discs, ordiscs with removable labels into the CD player as jamming mayoccur. Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning car...

• Terrain. Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems.Static can be caused on AM stations by power lines, electric fences,traffic lights and thunderstorms. Moving away from an interferingstructure (out of its “shado...

TRACTION CONTROL Y (IF EQUIPPED) This control can be used to turn theTraction Control y on or off. Refer to the Traction Control y section of the Driving chapter for more information. POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engin...

SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30 mph). Do not shift the gearshift leverinto N (Neutral) with the speedcontrol on. Do not use the speed control in heavy traffic or on roads thatare ...

To set a lower set speed • Press and hold CST −. Releasethe control when the desiredspeed is reached or • Press and release CST − tooperate the Tap-Down function.Each press will decrease the setspeed by 1.6 km/h (1 mph) or • Depress the brake pedal. Whenthe desired vehicle speed isreached, press SET...

Rear window wiper and washer (wagon only) The rear wiper control is locatedunder the headlamp controls Pressthe wiper control to activate therear wiper. Press again to turn offthe wiper. Press the washer control to activatethe rear washer. The wiper willcome on when the washer control ispressed, if ...

TILT STEERING Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the control. Never adjust the steering wheel when the vehicle is moving. REPLACING THE INTERIOR BULBS Check the operation of the...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps,lift the mirror cover. Adjust theamount of light by sliding thecontrol. MOON ROOF (IF EQUIPPED) Push up on the control to raise themoon roof to the vent position. Push the front portion of the controlrearward to open the moon r...

You will need a Phone Adapter System (PAS) that is compatible withyour cell phone that you install into the center console. This systemincludes a Phone Adapter Module (PAM) with a Wiring Harness and aHang-Up Cup. For more information, call 1–800–736–9450 to order thePhone Adapter System (PAS) for yo...

To prevent damage to the antenna or your car, remove the cellular phoneantenna mast before using an automatic car wash. POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to ...

POWER SIDE VIEW MIRRORS To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to disable adjust function. Heated outside mirrors (if equipped) Both mirrors are heate...

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment • Bin mat (snap-in) • Cupholders (front and rear) • Coin holder slots • Compact disc changer (if equipped) • Tissue holder • Rear A/C vent • Rear ashtray (see your Ford, Lincoln Mercur...

TRUNK REMOTE CONTROL Press the remote trunk releasecontrol on the instrument panel tothe left of the steering wheel. LIFTGATE (WAGON ONLY) You can open and close the liftgate and the liftgate window from outsidethe vehicle. It cannot be opened from inside the cargo area. • To open the liftgate windo...

To install the shade: 1. Fasten the cover into themounting brackets (make sure thecover is right side up). 2. Pull the end of the shade towardyou and hook the sides into thenotches (right side first) in the reartrim panels. To reduce the risk ofinjuries, the fasteners for cargo area cover must be pr...

2. Wrap the vinyl around the rollertube twice. Tuck the edges of thevinyl inside the end cap with eachwrap. 3. Fold the edges of the vinyltowards the center, making surethat the edges clear the end capslots. Use tape or a rubber band tohold the vinyl to the left side of thetube. 4. Push in the right...

Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment. The remote entry system allows you to lock or unlock all vehicle doors,trunk and liftgate without a key. The remote entry features only operate with the veh...

Unlocking the liftgate/trunk Press the control to unlock theliftgate/trunk. Sounding a panic alarm Press this control to activate thealarm. To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON. Panic alarm will only operate withthe ignition in the OFF position. Illuminate...

Replacing lost transmitters If a remote transmitter has been lostand you would like to remove itfrom the vehicle’s memory, or youwould like to purchase additionalremote transmitters and have themprogrammed to your vehicle: • Take all your vehicle’s transmitters to your dealer forprogramming, or • Pe...

The system is ready to arm whenever the key is removed from theignition. Any of the following actions will prearm the alarm system: • Press the remote entry lockcontrol (doors opened or closed). • Press 7/8 and 9/0 controls on thekeyless entry pad at the sametime to lock the doors (doorsopened or cl...

If the doors/hood or liftgate (wagon) are not closed and you press theremote entry transmitter twice to confirm the doors are locked, the hornwill chirp twice to warn you that a door/hood or liftgate (wagon) is stillopen. Disarming the system You can disarm the system by any of the following actions...

Triggering the anti-theft system The armed system will be triggered if: • Any door, liftgate or hood is opened without using the door key or theremote entry transmitter. • The trunk is forced opened. KEYLESS ENTRY SYSTEM (IF EQUIPPED) With the keyless entry keypad, youcan: • lock or unlock the vehic...

2. Press the 1/2 control within fiveseconds of step 1. 3. Enter your personal 5 digit code.Enter each digit within five secondsof the previous one. Do not set a code that includesthree of the same number orpresents them in sequential order.Thieves can easily figure out these types of codes. Your per...

2. To unlock the passenger’s door(s)and liftgate (wagon), press the 3/4control within five seconds ofunlocking the driver’s door. 3. To unlock the trunk or liftgate(wagon), enter the five-digitfactory-set code, then press the 5/6control within five seconds. Locking the doors and liftgate(wagon), pre...

The user should receive a horn chirp to indicate the system has been altered. Pressing the power door UNLOCK control button again will toggle theAutolock/Relock states. • Turn ignition to OFF to exit. Deactivating/activating horn chirp There are 2 methods to enable/disable this feature. One through ...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position. The THEFT light in the instrument cluster will flashevery two seconds when the vehicleis armed. Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle...

Programming spare keys A maximum of eight keys can be coded to your vehicle. OnlySecuriLock y keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readilyaccessible for ...

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the oper...

SEATING Adjustable head restraints Your vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head restraints is to help limithead motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it is l...

Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to reduce the risk ofinjuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

Using the manual lumbar support (if equipped) The lumbar control is located on thefront of the seat cushion. Turn to adjust lumbar support. REAR SEATS 2nd seat/split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additionalcargo space. To lower the seatback(...

SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of air bag-related injuries. The system is able to analyzedifferent occupant conditions and crash s...

common, moderate-severity impacts. A higher energy level is providedfor the most severe impacts. Whether or not the air bag deploys at allcan also be different for the driver versus the passenger based upondriver’s seat position and safety belt usage allowing further tailoring ofthe system. Determin...

When are the front air bags and pretensioners deployed? Front air bags and pretensioners aredesigned to activate in frontal andnear-frontal collisions, not rollover,side-impacts, or rear-impacts unlessthe collision causes sufficientlongitudinal deceleration. The factthat the pretensioners or air bag...

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a seat belt. Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the...

The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatoutboard safety belts have two types of locking modes described below: Energy management retractors Your vehicle has a seat belt system equipped with energy management...

Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing freeshoulder belt length adjustment to your movements and locking inresponse to vehicle movement. For example, if the driver brakessuddenly or turns a corner sharply, or the vehicle receives an impact ofapproxim...

• Grasp the shoulder portion andpull downward until the entirebelt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Disconnect the combinatio...

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions. The safety belt pretensioners are designed to activate only when thesafety belts are fastened during certain frontal or near-frontal collisionswith sufficient...

Front safety belt height adjustment Your vehicle has safety belt heightadjustments for the driver and frontpassenger. Adjust the height of theshoulder belt so the belt restsacross the middle of your shoulder. To lower the shoulder belt height,pull the control down and slide theheight adjuster down. ...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

To fasten the belt, pull the combination lap and shoulder belt from theretractor so that the shoulder belt portion of the safety belt crosses yourshoulder and chest. Be sure the belt is not twisted. If the belt is twisted,remove the twist. Insert the tongue into the proper buckle for yourseating pos...

If... Then... The driver’s safety belt is notbuckled before the vehicle hasreached at least 5 km/h (3 mph)and 1-2 minutes have elapsedsince the ignition switch has beenturned to ON... The Belt Minder feature isactivated - the safety belt warninglight illuminates and the warningchime sounds for 6 sec...

Reasons given... Consider... “Traffic is light” Nearly 1 of 2 deaths occur in single-vehiclecrashes, many when no other vehicles are around. “Belts wrinkle myclothes” Possibly, but a serious crash can do much morethan wrinkle your clothes, particularly if you areunbelted. “The people I’mwith don’t w...

Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front seat belt buckleassem...

severity. This information will assist Ford in the servicing of your vehicleand may help Ford better understand real world collisions and furtherimprove the safety of future vehicles. The air bag supplemental restraint system is designed to work inconjunction with the safety belts to help protect th...

Important supplemental restraint system precautions Air bags DO NOT inflate slowly orgently and the risk of injury from adeploying air bag is greatest close tothe trim covering the air bagmodule. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even ...

Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its ...

Determining if the system is operational The supplemental restraint system uses a warning indicator in theinstrument cluster or a back-up tone to indicate the condition of thesystem. Refer to the Warning Light section in the Instrument cluster chapter. Routine maintenance of the air bag is not requi...

How do the air bag supplemental restraints work? The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (...

How does the side air bag system work? The side air bag system consists ofthe following: • An inflatable nylon bag (air bag)with a gas generator concealedbehind the outboard bolster ofthe driver and front passengerseatbacks. • A special seat cover designed toallow airbag deployment. • The same warni...

Several air bag systemcomponents get hot after inflation. Do not touch them afterinflation. If the side air bag hasdeployed, the air bag will not function again. The sideair bag system (including theseat) must be inspected andserviced by a qualifiedtechnician in accordance withthe vehicle service ma...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. When possible, always place children under age 12...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

• Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position which is capableof providing a tether anchorage. For more information on top tetherstraps...

Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that itsbottom is perpendicular to the direction of webbing while sliding thetongue up the webbing.2. Place the child safety seat in the center seating position.3. Route...

Attach the lower anchors for child seat installation or loweranchors for child seat installation-compatible child seat only to the appropriate locations shown. If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the seat when the...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equipment standardrequirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the ...

Cold starting performance can also be improved with the use of anengine block heater. The engine block heater is available as a Fordoption and can also be obtained from your Ford dealer. Consult theengine block heater section for proper use of the engine block heater. If you should experience cold w...

BRAKES Your service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or int...

ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does notilluminate momentarily at start up, remains on or continues to flash, theABS needs to be serviced. With the ABS light on, the anti-lockbrak...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy. TRACTION CONTROL Y (IF EQUIPPED) Your vehicle may be equipped with the optional Traction Control y system. This system helps you maintain the stability and st...

During Traction Control y operation, the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine compartment and theengine will not “rev-up” when you push further on the accelerator. Thisis normal system behavior. The Traction Control y on/off ...

• high crown in center of road • high crosswinds • wheels out of alignment • loose or worn suspension components AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ...

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn off the ignition whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your dealer or a qualified s...

Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. Understanding gearshift positions P (Park) Always come to a complete stopbefore shifting into P (Park). Makes...

• Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It isdetermined by subtracting the weight of the loaded trailer towingvehicle from the GCWR for the towing vehicle. • Trailer Weight Range: Specified weight range that the tr...

Once through the water, always try the brakes. Wet brakes do not stopthe vehicle as effectively as dry brakes. Drying can be improved bymoving your vehicle slowly while applying light pressure on the brakepedal. Driving through deep water where the transmission vent tube issubmerged may allow water ...

3.0L 4-Valve Duratec Engine Model PassengerLoad - #/kg (lbs.) LuggageLoad - kg (lbs.) Max TrailerWt.- kg (lbs.) Sedan 5/340 (750) 0 590 (1 300) 2/135 (300) 70 (150) 725 (1 600) 2/135 (300) 0 795 (1 750) Wagon 5/340 (750) 70 (150) 455 (1 000) 2/135 (300) 70 (150) 660 (1 450) 2/135 (300) 0 725 (1 600)...

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The trailer brakes must meet local and Federalregulations. Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s bra...

• If you are driving down a long or steep hill, shift to a lower gear. Donot apply the brakes continuously, as they may overheat and becomeless effective. • The trailer tongue weight should be 10% of the loaded trailer weight. • After you have traveled 80 km (50 miles), thoroughly check yourhitch, e...

LUGGAGE RACK (IF EQUIPPED) The rear cross-bar can be adjusted to fit the item being carried. Thefront cross-bar does not move. Do not load more than 44 kg (100 lbs.)on the luggage rack. To adjust cross-bar position: 1. Loosen the thumbwheel at bothends of the cross-bar. 2. Slide the cross-bar to the...

Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the Basic warranty peri...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. NOTE: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panelcover. The fuses are coded as follows. Fuse/Relay Location Fuse Am...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 35 — Not Used 36 15A Turn Signals, Back-up Lamps 37 15A Transmission Position Switch 38 5A GEM Park Neutral Switch 39 — Not Used 40 — Not Used 41 — Not Used 42 — Not Used Power distribution box The power distribution bo...

When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label • tow a trailer • use tire chains • drive through an automatic car wash, because of the vehicle’s reducedgro...

5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground. 6. Put the jack in the jack notchnext to the door of the tire you arechanging. Turn the jack handleclockwise until the wheel iscompletely off the ground. 7. Remove the lug nuts w...

3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other movingparts. 4. Check all battery terminals and remove any excessive corrosion beforeyou attach th...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable. Make theconnection to an exposed metal part of the stalled vehicle’s engine, awayfrom the battery and the carburetor/fuel injection system. Do not use fuel ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch located ...

3.0L DOHC V6 Duratec engine 1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Engine oil filler cap 6. Engine oil dipstick 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power steering fluid reservoir 7 6 5 4 8 9 1 2 3 Mainten...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

• If the oil level is below the add1QT or MIN mark, add enough oilto raise the level within the1QT-FULL or the MIN-MAX range(depending on application). • Oil levels above the F in FULL or above the MAX mark, may causeengine damage. Some oil must be removed from the engine by aservice technician. 7. ...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

Checking and adding washer fluid for the liftgate (if equipped) The opening for the reservoir islocated on the passenger side underthe tail lamp. Refill this reservoirwith the same fluid you use for yourwindshield. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant ...

• Protection against rust and other forms of corrosion. • Enables calibrated gauges to work properly. When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant ...

Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservoir, when the engine is cool , until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot. Steam andscalding liqui...

• Do not use alcohol, methanol or brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corros...

Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level. If you have to add more than 1.0 lite...

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequatefreeze protection at the temperatures in which you drive in thewinter months. If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentrationabo...

1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right severaltimes. 3. Turn the engine off. Perform ...

TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance guide for scheduled intervals forfluid checks and changes. Your transaxle does not consume fluid.However, the fluid level should be checked if the transaxle is not workingproperly, i.e., if the transaxle sli...

Correct fluid level The transmission fluid should be checked at normal operatingtemperatures 66°C-77°C (150°F-170°F) on a level surface. The normaloperating temperature can be reached after approximately 30 km(20 miles) of driving. The transmission fluid should be inthis range if at normal operating...

1. Release and open the hood. 2. Remove the four clips located on the cowl vent screen. Maintenance and care 181

3. Remove the cowl vent screen. 4. Remove the two screws retaining the cowl top inner panel shield. 5. Remove the inner panel shield. Maintenance and care 182

6. Remove the filter from the cabin air filter housing. 7. Install the new cabin air filter into the cabin air filter housing. Maintenance and care 183

8. Replace the inner panel shield. 9. Replace the two screws retaining the cowl top inner panel shield. 10. Replace the cowl vent screen. Maintenance and care 184

11. Replace the four clips located on the cowl vent screen. BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte lev...

If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe battery terminals. If you see any corro...

2. Put the gearshift in P (Park), turn off all accessories and start theengine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. With your foot on the brak...

Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from thewindshield and lock into the serviceposition. 2. Turn the blade at an angle fromthe wiper arm. Push the lock pinmanually to release the blade andpull the wiper blade down towardthe windshield to remove it from ...

The temperature grade for this tire is established for a tire thatis properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or incombination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Us...

Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification or Tire Label. Make sure that all tires are the same size,speed rat...

Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory orequivalent. SAE class “S” or other conventional link type chains maycause damage to the vehicle’s wheel house and/or body. • Install cable chains securely, verifying that the cabl...

Fuel ethanol and gasoline may contain benzene, which is acancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harm...

The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO N...

your VIN or the label on the inside of your fuel filler door. Whenchecking the VIN, look for the engine type identifier (8th character). Ifyour vehicle is an FFV, then the character will be labeled as a “K.” Standards for fuel ethanol have been developed to provide FFVs the bestpossible performance,...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in litersor gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

• Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain ifunnecessary shifting between third and fourth gear occurs.Unnecessary shifting of this type could result in reduced fueleconomy. • Warming up a vehicle on cold mornings i...

EPA window sticker Every new vehicle should have the EPA window sticker. Contact yourdealer if the window sticker is not supplied with your vehicle. The EPAwindow sticker should be your guide for the fuel economy comparisonswith other vehicles. It is important to note the box in the lower left corne...

Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, trades vehicles, or supervises a fleet of vehic...

• Tail lamps • Brakelamps • High-mount brakelamp • Turn signals • Backup lamps • License plate lamp Do not remove lamp bulbs unless they will be replaced immediately. If abulb is removed for an extended period of time, contaminants may enterthe lamp housings and affect performance. Replacing headlam...

Replacing front parking lamp/turn signal/cornering lamp bulbs 1. Make sure the headlamp controlis in the OFF position. 2. Remove the bolt from theheadlamp housing. 3. At the back of the headlamp, pryup and remove the two retainer pinsto release the headlamp assemblyfrom the vehicle and pull headlamp...

Replacing high-mount brakelamp bulbs — Sedan only • TYPE A 1. Open trunk and locate theinsulator under the rear window. Note the number of the push pinsbefore removal. 2. Remove the insulator by carefullyprying out the push pins to gainaccess to the bulb sockets. 3. Remove the bulb socket byrotating...

Replacing high-mount brakelamp bulbs — Wagon only 1. Open liftgate. 2. Remove two screw covers, screwsand handle from liftgate. 3. Remove two screws and the lowertrim panel from the liftgate. 4. Remove the upper trim panel. 5. Remove the rubber plug from thelower access hole in the upperportion of t...

7. Carefully lift the lamp assemblyaway from the liftgate. 8. Remove the bulb socket byrotating it counterclockwise andpulling it out from the lampassembly. 9. Carefully pull the bulb straightout of the socket and push in thenew bulb. 10. To complete installation, followthe removal procedure in reve...

CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approvedcleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty, use aquality c...

Use only carnauba or synthetic-based waxes. Use a cleaning fluid with aclean cloth to remove any bugs before waxing your vehicle. Use tarremover to remove any tar spots. Avoid getting wax on the windshield, or on any surfaces which appearcoarse or bumpy. If you have wax applied at a commercial car w...

Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Ifnecessary, use a tar remover such as Ford Extra Strength Tar and RoadOil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemicalsolvents or abrasive cleaners. Cleaning th...

Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion ofthe instrument panel. The dull finish in this area helps protect the driverfrom undesirable windshield reflection. Do not use chemical solvents or...

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended forcleaning upholstery or carpets. Do not bleach or dye the belts, becausethese actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are nonicks, tears ...

MOTORCRAFT PART NUMBERS Component 3.0L V6 Vulcanengine 3.0L FFV V6engine 3.0L DOHC V6Duratec engine Air filterelement 1 FA-1683 FA-1683 FA-1683 Fuel filter FG-1006 FG-1006 FG-1006 Battery(standard) BXT-58R BXT-58R BXT-36R Battery(optional) BXT-36R N/A N/A Oil filter FL-400-S FL-400-S FL-820-S PCV va...

Ford Extended Service Plan You can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESPis an optional service contract which is backed by Ford Motor Companyor Ford Motor Service Company (in the U.S.) and Ford of Canada (inCanada). ...

taken to another dealer. If a particular dealership can not assist you,then contact the Customer Relationship Center. If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at yourselling/se...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Companyvehicles The Dispute Settlement Board may not be available in all states. FordMotor...

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

You will receive a letter of explanation if your application does notqualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requireme...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADAONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Busi...

• The Federal Communications Commission (FCC) and Canadian RadioTelecommunications Commission (CRTC) regulate the use of mobilecommunications systems - such as two-way radios, telephones andtheft alarms - that are equipped with radio transmitters. Any suchequipment installed in your vehicle should c...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar compl...

A Accessory delay ..........................63 Air bag supplemental restraintsystem ........................104, 106, 110 and child safety seats ............107description ......................106, 110disposal ....................................112driver air bag ..........105, 109, 111indicator li...

Locks autolock .....................................78childproof ..................................63 Lubricant specifications ...224, 226 Lumbar support, seats ...............87 M Mirrors .........................................60 cleaning ...................................217heated ................

Item Information Required fuel Refer to 9 Octane recommendations 9 in the Maintenance and care chapter. Fuel tank capacity 68.1L (18 gallons) Engine oil capacity (including filterchange)-3.0L V6 Vulcan engine 4.25L (4.5 quarts). Use MotorcraftSAE 5W-20 Super Premium MotorOil, Ford specificationWSS-M...