Fisher-Price C4492 - Manual

Table of Contents:

• Page 4 – alkaline
• Page 5 – WARNING; CHOKING HAZARD; Not for children under 3 years.; CAUTION; This product contains small parts
• Page 6 – Left
• Page 8 – flag in the
• Page 10 – Remove the battery compartment door.; BATTERY SAFETY INFORMATION; under adult supervision.
• Page 12 – DECORATION; • Apply the labels as indicated in the illustrations.
• Page 14 – • Position the; Crossbar
• Page 15 – • Insert an M5 x 29 mm bolt through the outside of the; rounded side out; hex hole in the crossbar.; Rounded
• Page 16 – • Insert an M5 x 29 mm bolt through the outside; matching hex hole in the crossbar.; M5 Lock Nuts
• Page 17 – • Fit the lower net clip into the slot in one of the bases.; Base Slot
• Page 18 – • Insert three #8 x 15 mm screws into the lower net clip; Lower Net Clip
• Page 20 – Right Base
• Page 21 – BACK VIEW; Screws
• Page 22 – Make sure the wire is toward the lower net clips.; Putting Green
• Page 23 – • Insert six #8 x 15 mm screws into the putting green
• Page 24 – Bar; CORRECT
• Page 25 – read; • Fit the goal wire down through the hole in the base.; Goal Wire
• Page 26 – • Lift the assembly to pull the wire completely through the hole.
• Page 27 – • Fit the ends of the goal into the holes in the; Goal Tubes
• Page 29 – Yellow Markings; • Find the yellow markings on the back of the goal
• Page 30 – Clips
• Page 31 – Golf Cup Wire
• Page 32 – • Fit the goal wire through the same hole in the base.
• Page 33 – Wire Clip
• Page 34 – • Fit the goal and golf cup wires into the wire clip.; Clip
• Page 36 – ASSEMBLY; Net Tube 2A
• Page 38 – • Slide a foot onto the end of a net tube assembly.; Tip: The foot fits only to the wide end of a net tube assembly.
• Page 40 – and the strap at the tip is furthest from the base assembly.
• Page 42 – Net Tube Assembly
• Page 43 – • Continue to slide the net tube assembly labeled 1A, 2A, 3A through; all three; net; Net Sleeves
• Page 44 – Foot Slot
• Page 45 – Net Pivot
• Page 46 – • Insert an M5 x 29 mm bolt into a net pivot and tighten.
• Page 47 – Upright
• Page 48 – Chute
• Page 49 – • Fit the chute tubes
• Page 50 – M5 Lock Nut
• Page 51 – Sleeve; White Dot
• Page 52 – Fasteners; • Open the fasteners on one side of the chute, as shown.; SIDE VIEW
• Page 54 – • Fit one end of the ball sensor tube into the slot in a chute tube.; Ball Sensor
• Page 55 – Chute
• Page 56 – Slots; • Pull the fabric on the chute ring up; “snap”; the flat tabs on; Chute Ring
• Page 58 – Chute Straps; • Fasten; all three chute straps; around
• Page 60 – into place. Make sure the support tube is fitted to the
• Page 61 – • Fit the game selector to a chute tube.; Tip: The game selector fits to only one chute tube.
• Page 62 – • Fit the game selector retainer to the game selector and chute tube.; Game Selector
• Page 63 – • Insert three #8 x 15 mm screws into the game selector
• Page 64 – Upper Net Clip
• Page 66 – Scoreboard Wires
• Page 67 – • Push to fit the scoreboard into place on the backboard.
• Page 68 – • Insert four #8 x 15 mm screws into the
• Page 69 – • Fit the backboard tube into the grooves on the backboard.; Backboard Tube
• Page 70 – Chute Tubes
• Page 71 – • Insert four #8 x 37 mm screws through
• Page 72 – Buckle; • First, remove the fabric from the chute strap.
• Page 74 – • Fit the rim wire through the slot in the backboard.; Rim Wire
• Page 75 – • Push to; the pegs on the rim into the hinge on the backboard.; Rim
• Page 76 – Peg
• Page 78 – Bolt
• Page 80 – • Insert an M5 x 29 mm bolt into the handle pivot and tighten.; Tip: The handle pivot includes an M5 lock.; • Repeat Assembly Steps 66 and 67 to assemble the other handle pivot
• Page 81 – • With the fastener straps up,
• Page 82 – Tip: Each handle pivot includes an M5 lock nut.
• Page 84 – Handle Strap
• Page 85 – • Note the five wires from the various parts of the Game Station; and the corresponding; Scoreboard
• Page 88 – Storage Cover
• Page 89 – • Fit all five wires under the tabs inside a wire cover.; Tabs
• Page 90 – Wire Cover
• Page 91 – • Fit four #8 x 15 mm screws into the wire covers; Wire
• Page 92 – Straps
• Page 97 – • Open the strap on the upper sleeve in; Upper
• Page 98 – • Open the strap on the lower sleeve in; Lower Sleeve
• Page 99 – Cable Tie
• Page 100 – • Insert and; the shaft into the blade.; Shaft
• Page 102 – • Lower the rim on the backboard.
• Page 103 – • Push the buttons and lift the handle from; LIFT
• Page 104 – • Continue to lift the handle to unfold the chute.
• Page 106 – • Wrap the straps on each side of the chute; Power
• Page 107 – SOCCER, HOCKEY AND GOLF; adjacent loop in the net.
• Page 108 – • Lift and then lower the handle to fold the chute.; Handle
• Page 110 – • To play hockey, clip the target to the bar
• Page 111 – • The target can be positioned to the left or right up or down.; Tip: Positioning the target up or down requires some force.
• Page 112 – • For golf, fit the flag into the golf cup.
• Page 113 – Wipe clean to remove soap residue.
• Page 125 – Finish your round at even par!
• Page 127 – • Lift and then lower the handle to fold the ball chute.
• Page 128 – • Push the handle to
• Page 129 – • Pull the nets out slightly.; Tip: You MUST pull the nets out slightly, before lifting the nets!
• Page 130 – Net; • Lift the nets. You will hear a “popping” noise from the net pivots.
• Page 131 – • Hook the nets into the upper net clips.
• Page 133 – • Fold the nets to the backboard.
• Page 134 – Putter; • Place all the balls and puck in the fold in the chute.; Flag
• Page 135 – SYMPTOM
• Page 138 – UNITED STATES
• Page 139 – This Class B digital apparatus complies with Canadian ICES-003.