Page 3 - TABLE OF CONTENTS; SAVE THESE INSTRUCTIONS
1 TABLE OF CONTENTS IMPORTANT! SAVE THESE INSTRUCTIONS The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website fisherpaykel.com or c...
Page 4 - SAFETY AND WARNINGS; Electric Shock Hazard; INTEGRATED COLUMNS; Note: Interchangeable door hinges available for each model.; FREEZER
2 1 SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Read and follow the safety and warnings outlined in this installation guide before operating this appliance.Failure to do so can result in death, electric shock, fire or injury to persons. ! WARNING! Cut Hazard Take care — panel edges are sha...
Page 5 - COMPONENTS LIST; Installation kit; — included with the appliance
3 3 COMPONENTS LIST Installation kit — included with the appliance Door panel attachment kit #8 x 16 Mush Washer Twin Thread Philips Screw #8 x 16 Mush Washer Twin Thread Philips Screw M5 x 14 Mush Head SS Philips Screw M5 x 14 Mush Head SS Philips Screw Side bracket (6x) Bracket slider (6x) Side ...
Page 6 - — included with the appliance.; Water filter installation kit; Toe kick installation kit; — Fisher & Paykel (Stainless steel) toe kick is not included with the; Install parts; — included with the appliance. Attached to back of appliance.
4 3 COMPONENTS LIST MI (miscellaneous items) pack — included with the appliance. U S E R G U I D E N Z AU I N T E G R AT E D CO LU M N S RS4621F, RS6121F, RS7621F, RS6121S & RS7621S models 849165A BOOK UG REF Columns AA FA.indd 1 16/07/18 2:10 PM S E RV I C E & WA R R A N T Y S E RV I C E ...
Page 7 - Door handle kit; — not included with the appliance and must be purchased separately.; Door panels; Custom door panel; Dual install joiner kit; — included with the appliance (Freezer model only). Attached; Included in each joiner kit:; Top joiner fastener kit; Top joiner bracket kit
5 3 COMPONENTS LIST Door handle kit — not included with the appliance and must be purchased separately. EVO1 handle kit (CA: 24980) F&P (D3) handle kit (CA: 24979) M5 x 25 Pan Head Socket ScrewOR M5x25 hex screw M5 x 25 Pan Head Socket ScrewOR M5x25 hex screw M5 x 25 Pan Head Socket ScrewOR M...
Page 8 - Hinge change kit; MODEL
6 3 COMPONENTS LIST Hinge change kit — not included with the appliance and must be purchased separately. Hinge change assembly Hinge top pocket (1x) K05 Top adapter bracket (2x) Lower hinge bracket (2x) M5 Nut (2x) Alcove top bracket (2x) K05 Bottom adapter bracket (2x) Top (fixed) grille assembly...
Page 9 - PRODUCT DIMENSIONS AND SPECIFICATIONS
7 4 PRODUCT DIMENSIONS AND SPECIFICATIONS RS46 RS61 RS76 PRODUCT DIMENSIONS mm mm mm A Overall height of product 2134 2134 2134 B Overall width of product 451 603 756 C Overall depth of product (excluding front door panel) 610 610 610 PRODUCT SPECIFICATIONS Door clearance 508 660 813 Weight (includ...
Page 10 - CABINETRY OPTIONS; FRAMELESS CABINETRY
8 5 CABINETRY OPTIONS FRAMELESS CABINETRY (Frameless: Aligns the product/s with the cabinetry) FRAMED CABINETRY (Framed: Aligns the product/s with the frame of the cabinetry) Note: Images shown for single install. These options are also applicable for dual install. E D D E Frameless E D D E Framed
Page 11 - CAVITY DIMENSIONS; Overall height of cavity; Note: These dimensions are intended for ‘Flush Installation’ only.
9 6 CAVITY DIMENSIONS SINGLE INSTALL DUAL INSTALL RS46 RS61 RS76 RS46 + RS61 RS46 + RS76 RS61 + RS61 RS61 + RS76 RS76 + RS76 CAVITY DIMENSIONS mm mm mm mm mm mm mm mm A Overall height of cavity 2134 2134 2134 2134 2134 2134 2134 2134 b Overall width of cavity 457 610 762 1067 1219 1219 1372 1524 c ...
Page 12 - DOOR AND TOE KICK PANEL DIMENSIONS; Width of toe kick
10 7 DOOR AND TOE KICK PANEL DIMENSIONS RS46 RS61 RS76 DOOR PANEL DIMENSIONS (STAINLESS STEEL) mm mm mm A Height of door panel 2029 2029 2029 B Width of door panel 451 603 756 C Depth of door panel (excluding door handle) 19 19 19 DOOR PANEL DIMENSIONS (CUSTOM)* A Height of door panel 1978 – 2080...
Page 13 - SINGLE INSTALL
11 7 DOOR AND TOE KICK PANEL DIMENSIONS E F E E E F 102mm toe kick height 152mm toe kick height 51mm toe kick height (with extra lower grille attached) 73 – 102mm toe kick depth measured from the from rear of door panel A C B D E SINGLE INSTALL A C B B D E DUAL INSTALL
Page 14 - CUSTOM DOOR PANEL DIMENSIONS; Custom door panel dimensions
12 8 CUSTOM DOOR PANEL DIMENSIONS Custom door panel dimensions Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on http://thekitchentools.fisherpaykel.com IMPORTANT! ● ● The thickness of the custom ...
Page 16 - DOOR OPENING ROTATION; open) measured from front of door
14 9 DOOR OPENING ROTATION RS46 RS61 RS76 DOOR OPENING AND CLEARANCE DIMENSIONS mm mm mm A Width of door ( 90° open) measured from front of door 508 660 813 b Minimum door clearance* to adjacent wall** (115° — full internal access) 292 356 419 c Minimum door clearance* to adjacent wall** (90° — red...
Page 17 - ELECTRICAL AND PLUMBING; appliance is installed.; ISO VIEW OF CAVITY
15 !0 ELECTRICAL AND PLUMBING ELECTRICAL SPECIFICATIONS FREEZER REFRIGERATOR Supply 230 VAC, 50 Hz 230 VAC, 50 Hz Service 10 amp circuit 10 amp circuit Socket 3-pin earthing-type 3-pin earthing-type Power cord (excluding plug) 2190mm 2190mm PLUMBING SPECIFICATIONS FREEZER REFRIGERATOR Supply 1/2” B...
Page 18 - BEFORE INSTALLATION; Check the installation location; Check the cabinetry
16 !1 BEFORE INSTALLATION IMPORTANT! ● ● Ensure your appliance is not exposed to any heat generating appliance eg cooktop, oven or dishwasher. ● ● The appliance has front and rear rollers for moving the appliance forward and backward. Do not move the appliance sideways to avoid damaging the rollers...
Page 19 - UNPACKING AND MOVING YOUR PRODUCT; Do not open the doors to prevent the appliance from tipping over.; Do not insert the cart from the back or front side!; Unpacking your product
17 !2 UNPACKING AND MOVING YOUR PRODUCT 1 Remove the top of the packaging carton. Cut along the cut lines and remove the carton and EPS (Expanded Polystyrene) foam. 2 Remove pre-packed install parts (door panel side extrusion and side trim assembly, centre trim assembly, dual install joiner kit) ta...
Page 20 - ATTACH THE ANTI-TIP BRACKET; For wooden/plaster board wall installation:
18 IMPORTANT! Make sure the bracket overlaps the appliance by a minimum 180mm for a secure hold ( E) . If the minimum 180mm overlap cannot be achieved, install a solid spacer to the wall stud behind the bracket ( F) . !3 ATTACH THE ANTI-TIP BRACKET min 180mm E Bracket Appliance Wall F Bracket Space...
Page 21 - CONNECT TO WATER AND POWER SUPPLY; WARNING — connect to potable drinkable water supply only.
19 !4 CONNECT TO WATER AND POWER SUPPLY F A WARNING! ● ● The water connection instructions below are intended only for the professional installer. ● ● WARNING — connect to potable drinkable water supply only. ● ● DO NOT install on line pressure above 120psi (827kPa) or below 22psi (150kPa). ● ● DO ...
Page 22 - SINGLE INSTALLATION; Installing depth alignment gauges; x Cabinet depth alignment gauges
20 !5 SINGLE INSTALLATION Installing depth alignment gauges Note: The alignment gauges are only temporary and removable after installation. Required components/tools: ● ● 4x Cabinet depth alignment gauges ● ● Cross-head screwdriver 1 Loosen the screws at the right and left, top and bottom corners o...
Page 23 - damage and possible water leaks.; Coil the water hose flat behind the appliance.; Aligning the appliance inside the cabinetry; relative to the thickness of the door panel.
21 C !5 SINGLE INSTALLATION IMPORTANT! ● ● Ensure that the hose is not run over when moving the appliance/s to prevent damage and possible water leaks. ● ● Use low speed, low torque setting when using powered drill. ● ● Ensure power cord is not damaged during installation. Positioning the appliance...
Page 24 - Adjusting height of the appliance inside the cabinetry
22 !5 SINGLE INSTALLATION 2 Continue turning the adjusting screws alternately between front and rear feet until you achieve the correct alignment. 3 Once you are satisfied with the alignment, raise the height of the appliance by alternately adjusting the front and rear feet until the top surface co...
Page 25 - DUAL INSTALLATION
23 Attach central spacer to cabinetry Note: The spacer must be attached between the first and second appliances. The attachment location of the spacer to the alcove ceiling depends on the model of each appliance. Central spacer Depth alignment gauge 1 Measure from the alcove side towards the centre....
Page 26 - x Depth alignment gauges
24 !6 DUAL INSTALLATION Installing depth alignment gauges Note: The alignment gauges are only temporary and removable after installation. Required components/tools: ● ● 4x Depth alignment gauges ● ● Cross-head screwdriver 1 Loosen the screws at the right and left, top and bottom corners of the door...
Page 27 - installed to the door.
25 !6 DUAL INSTALLATION Positioning and aligning the first appliance inside the cabinetry 1 Coil the water hose flat behind the appliance. (Refer to ‘Connect to water and power supply’). 2 Before rolling the appliance, insert a barbed plug into a large hole on the cabinetry side of the first applia...
Page 28 - twisting and poor door sealing.
26 !6 DUAL INSTALLATION IMPORTANT! ● ● Ensure the doors are in line with the cabinetry front and the appliance is centred. ● ● All four corners of the appliance must be supported firmly onto the floor to eliminate any movement. Installing the appliance on a soft, uneven, or not level floor may caus...
Page 30 - alignment of both appliances.; Adjusting height of the second appliance inside the cabinetry
28 !6 DUAL INSTALLATION 2 Continue turning the adjusting screws alternately between front and rear feet until you achieve the correct alignment of the second appliance with the first appliance. 3 Once you are satisfied with the alignment, raise the height of the appliance by alternately adjusting t...
Page 31 - Fixing the second appliance inside
29 !6 DUAL INSTALLATION Fixing the second appliance inside the cabinetry 1 Fix the top caps of first and second appliances to the central spacer with the top joiner fastener kit ( A ). 2 Fix the bottom joiner brackets of both appliances together with the bottom joiner kit ( B ). – Place the plastic...
Page 32 - INSTALL WATER FILTER; Flushing the water filter
30 !7 INSTALL WATER FILTER 1 Remove the water filter packaging. 2 Pull the filter tool gently to dislodge from the front of the appliance ( A ). 3 Insert the water filter all the way into the filter casing and press firmly until the filter head is pushed further inside the casing ( B ). 4 Using the...
Page 33 - INSTALL BRACKETS TO DOOR PANEL (STAINLESS STEEL); when the installation is complete.
31 !8 INSTALL BRACKETS TO DOOR PANEL (STAINLESS STEEL) IMPORTANT! Ensure to protect the finish of the Fisher & Paykel Stainless Steel door panels. Leave the protective film on the panels when hanging and remove the film only when the installation is complete. Required components/tools: ● ● Door...
Page 35 - INSTALL DOOR PANELS; For Stainless steel door panel:
33 @0 INSTALL DOOR PANELS Attach the door handle 1 For Stainless steel door panel: ● ● Remove the plastic plugs from handle holes (x4). ● ● Align the handle to the holes and secure with M5x25 hex screws ( A ). For Custom panels: ● ● Fix the handle with M5x25 hex screws from the inner edge of the pa...
Page 36 - Adjust the door panel
34 @0 INSTALL DOOR PANELS Adjust the door panel Note: All door panels have full axis adjustment to ensure they are flush with adjacent walls. 1 To adjust the height of the door panel relative to the door, use M4 hex key to turn the top M8 screw ( A ) clockwise to lower or counter-clockwise to raise...
Page 37 - INSTALL TOE KICK; steel and Custom panels to be attached to the magnet.
35 @1 INSTALL TOE KICK 4 Place the toe kick in front of the mounting plate. Ensure that the spacers at back of the toe kick are aligned with the magnets ( E ). – For custom toe kick, skip step 3 as spacers are not needed. 5 Attach the toe kick by pressing onto the mounting plate ( F ). – For stainl...
Page 38 - INSTALL TOE KICK GRILLE; Adjusting the toe kick grille; x16mm Pan head screws; For 51mm toe kick height, an additional lower grille can be ordered.; x16mm pan head screws.; Attach the top and bottom grilles; ) with 8x16mm pan head
36 @2 INSTALL TOE KICK GRILLE Adjusting the toe kick grille 1 Loosen the cap screws of the adjustment brackets from both sides of the plinth using a hex key ( A ). 2 Adjust the toe kick to the desired depth by moving it forward/backward ( B ). 3 Re-tighten the cap screws of the adjustment brackets ...
Page 39 - INSTALL CABINET TRIMS; Install the side trims; Slide the trim behind the lower hinge (; Position the trim on the throat with an angle. (
37 @3 INSTALL CABINET TRIMS Install the side trims Note: Four (4) dual-lock strips are pre-installed along each side trim. 4 Slot trim in behind top hinge pocket ( E ), then press ( F ) adhesive to cavity ensuring trim is also tight against appliance inner face. Note: Press firmly on the dual-lock ...
Page 40 - Install the top trim
38 @3 INSTALL CABINET TRIMS Install the top trim 1 Slide the top trim into hinge pocket of the cabinet ( A ), and then engage the dual lock at the non-hinge side ( B ). B A Install the centre trims (for dual install only) Note: Four (4) dual-lock strips are pre-installed along the centre trim. 2 Po...
Page 41 - INSTALL FLOW DIVIDER AND DOOR TRIMS; from bypassing in front of the bottom grille.; Install the door trims
39 @4 INSTALL FLOW DIVIDER AND DOOR TRIMS Required components/tools: ● ● 1x Door flow divider ● ● 1x Flow divider cap ● ● 1x 8Gx16 Countersunk screw ● ● 2x Trim caps ● ● Top door panel extrusion ● ● 2x Door panel side extrusion ● ● Saw ● ● File IMPORTANT! The door flow divider is pre-assembled to t...
Page 42 - Removing the door; OPTIONAL — CHANGING OVER DOOR HINGES; Close the door and lay the appliance on its back on the pallet.
40 Removing the door 1 Release the hinge spring by turning the star T20 screws in the hinge to the “0” position ( A ). @5 OPTIONAL — CHANGING OVER DOOR HINGES You have the option to change the door hinge side of your appliance from right hand hinge to left hand hinge or vice versa. A hinge change k...
Page 43 - Removing the top door hinge
41 @5 OPTIONAL — CHANGING OVER DOOR HINGES Removing the top door hinge 1 Rotate the top hinge ( A ) outwards and remove the top hinge pocket cover ( B ) using the flat head screwdriver in the slot of the cover. 2 Remove the hinge by unscrewing the M5x12 pan head screws (2x) ( C ), and set aside for...
Page 44 - Unclip the reed switch from the housing (
42 Required components/tools: ● ● Star T20 screwdriver ● ● Flat head screwdriver Moving the sensor housing (RS46 & RS61 only) @5 OPTIONAL — CHANGING OVER DOOR HINGES G A B C E F D 1 Unclip the reed switch from the housing ( A ). 2 Unhook the interceptor board harness from sensor housing so harn...
Page 45 - Top hinge installation; – Ensure that the tab on the top of the
43 @5 OPTIONAL — CHANGING OVER DOOR HINGES Top hinge installation 1 Reinstall the hinge top bracket and bracket spacer with M5x12 countersunk screws ( A ) on the new hinge side at the other side of the appliance. 2 Install the new hinge pocket and alcove top bracket on the new hinge side using two ...
Page 46 - Door brackets
44 @5 OPTIONAL — CHANGING OVER DOOR HINGES Required components/tools: ● ● 2x K05 Top adapter bracket ● ● 2x K05 Bottom adapter bracket ● ● Star T20 screwdriver ● ● Flat head screwdriver Door brackets 1 Remove the top adapter bracket from the top of the door by unscrewing M5x10 screws (4x) ( A ). 2 ...
Page 47 - Door installation; Star T20 screwdriver
45 @5 OPTIONAL — CHANGING OVER DOOR HINGES Top hinge A Bottom hinge A Door installation 1 Reinstall the door to the appliance by fixing M6x10 hex screws (4x) into the hinges ( A ). Required components/tools: ● ● Star T20 screwdriver ● ● Flat head screwdriver ● ● Hex driver B 2 Activate the hinge sp...
Page 48 - FINAL CHECKLIST; TO BE COMPLETED BY THE INSTALLER; Check all parts are installed.; Ice models only; Ensure the water filtration system has been flushed.
46 @6 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the door/drawer can open and close freely with no resist...
