Fisher & Paykel DD90SDFTX2 - User Manual

Page 2 - FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL

2 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL 1 DD90SDF(H)TX2 DD90SDFTM2 Designer PRODUCT & CABINETRY DIMENSIONS PARTS SUPPLIED CAVITY PREPARATION MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE SECURE WITHOUT DRAWER REMOVAL RECOMMENDED METHOD (a) ALTERNATIVE METHOD (b) SECURE...

Page 3 - ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY; Cut hazard; SAFETY AND WARNINGS - ALL MODELS; Very Heavy; IMPORTANT SAFETY INSTRUCTIONS!; Electrical Shock Hazard

3 ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY 2b WARNING! Cut hazard Take care - panel edges are sharp. Failure to use caution could result in injury or cuts. IMPORTANT SAFETY INSTRUCTIONS! Read these instructions completely and carefully. Ensure the product is not plugged in. Installati...

Page 4 - PARTS SUPPLIED - ALL MODELS

4 PARTS SUPPLIED - ALL MODELS 3a If the Drain hose supplied is not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose by 3.6m. The kit is available from the nearest Fisher & Paykel Authorised Service Centre or through our local...

Page 5 - ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS

5 ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS 3b External Venting kit (1) supplied with Integrated models with remote (NZ AU) only Panel mounting screws (14) Panel bracket (1) (attached to product) Integrated rectangular badge (1) (Satin chrome supplied) supplied with Integrated models with bad...

Page 6 - PRODUCT DIMENSIONS; Product dimensions

6 4 PRODUCT DIMENSIONS A H I J K Side Plan G F B C D E Product dimensions (mm) Desig ner In te grate d Remote contr ol In te grate d Badge c ontr ol A overall height 1 of product (incl. front panel height) 478 478 478 B overall width of product 895 min. 855 min. 855 C overall depth of product (excl....

Page 7 - CABINETRY DIMENSIONS; L M; Cabinetry dimensions

7 5 CABINETRY DIMENSIONS Plan Side L M P ON 18 mm 20 mm 2 mm ON Minimum clearances from adjacent cabinetry Cabinetry dimensions mm Desig ner In te grate d Remote contr ol In te grate d Badge c ontr ol L height of cavity (from support surface to undersideof benchtop) 480 480* 480* M inside height of ...

Page 8 - FRONT PANEL SPECIFICATIONS; min. 2mm ventilation gap with

8 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WIDTH OF THE PANEL Measure A ( the width between adjacent door/drawer fronts) and write it in the fi rst box below, then complete the equation. HEIGHT OF THE PANEL Measure B and write it in th...

Page 9 - min. 8 mm ventilation gap

9 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WIDTH OF THE PANEL Measure A ( the width between adjacent door/drawer fronts) and write it in the fi rst box below, then complete the equation. HEIGHT OF THE PANEL Measure B and write it in th...

Page 10 - CAVITY PREPARATION; Water Connection; Water softener models; BENCHTOP

10 7a CAVITY PREPARATION Water Connection Recommended COLD (Maximum 60°C). ¾ “ BSP (GB20) to suit flat washer. Water Pressure Water softener models Max. 1 MPa (145 psi)Min. 0.1 MPa (14.5 psi) Models without water softener Max. 1 MPa (145 psi)Min. 0.03 MPa (4.3 psi) Important! Adjacent cabinetry must...

Page 11 - Shelf cutouts

11 7b 7c INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINET INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH ADJACENT CABINET ø 60 mm ø 60 mm max. 5 mm max. 5 mm 220 mm 220 mm 100 mm 100 mm ø60mm Services can be loc...

Page 12 - MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE; Left hand side

12 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE Left hand side Right hand side Drain hose - 2000 mm Inlet hose - 1650 mm Venting hose - 1265 mm Venting hose - 1925 mm (Integrated models only) (Integrated models only) Power cord (excl. plug) - 750 mm Power cord (excl. plug) - 400 mm Drain...

Page 15 - INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - SECURE THE EXTERNAL VENT; Airflow

15 12a 11a PULL THROUGH HOSES & MOVE INTO THE CAVITY SECURE THE DRAWER 1 3 2 Open the drawer halfway. Using a flat-bladed screwdriver, prise the grey rubber plug out of the trim moulding. Replace the grey rubber plug back intothe trim moulding and ensure the trimseal is facing forward. Repeat fo...

Page 22 - ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS

22 ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS Insert an appropriately sized Philips screwdriver into the hole above the door pin and rotate the panel up or down to align the gaps in your cabinetry. Repeat on the other side if necessary. The panel has a maximum travel of 2 mm up or down. Importa...

Page 23 - Dishwasher using sink trap with drain hose joiner; Dishwasher and Standpipe Ø 38; CONNECT INLET HOSE TO COLD WATER; see

23 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. 22 1 3 2 750-882.5 mm 1 2 38 mm max. 120 mm 750-882.5 mm * * 3 4 5 If space is limited for fixing, push hose through drain hose support to required height If space is limited for fixing, push hose through drain ...

Page 24 - SAVE THESE INSTRUCTIONS

24 26 25 FINAL CHECKLIST TROUBLESHOOTING Check all parts are installed. Ensure product is level, securely fastened to the cabinetry and opens and closes freely. The drawer must be free to fully close with no resistance from the cabinetry. Ensure inlet hose to water supply has supplied rubber washer ...

Fisher & Paykel DD90SDFTX2 - User Manual

Table of Contents:

Summary

Other Fisher & Paykel Dishwashers Models