Page 2 - FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL
2 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL 1 DD60SHI7 Classic PRODUCT & CABINETRY DIMENSIONS (STANDARD HEIGHT) PRODUCT & CABINETRY DIMENSIONS (STANDARD HEIGHT) PRODUCT & CABINETRY DIMENSIONS (STANDARD HEIGHT) PRODUCT & CABINETRY DIMENSIONS (TALL HEIGHT) PRODUCT & C...
Page 3 - Electrical shock hazard; IMPORTANT SAFETY INSTRUCTIONS!; Electrical Shock Hazard
3 SAFETY AND WARNINGS - ALL MODELS ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY 2a 2b WARNING! Electrical shock hazard Before installing the dishwasher, remove the house fuse or open the circuit breaker. This appliance must be earthed. In the event of a malfunction or breakdown, earthing ...
Page 4 - PARTS SUPPLIED - ALL MODELS
4 PARTS SUPPLIED - ALL MODELS 3a If the Drain hose supplied is not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose by 3.6m. The kit is available from the nearest Fisher & Paykel Authorised Service Centre or through our local...
Page 5 - ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS
5 ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS 3b External Venting kit (1) supplied with Integrated models with remote (NZ AU) only Panel mounting screws (6) Panel bracket (1) (attached to product ) Integrated rectangular badge (1) (Satin chrome supplied) supplied with Integrated models with bad...
Page 6 - PRODUCT DIMENSIONS; Product dimensions
6 4 PRODUCT DIMENSIONS A H I J K Side Plan G F B C D E Product dimensions (mm) STANDARD HEIGHT MODELS TALL HEIGHT MODELS Classic Desig ner In te grate d Remote contr ol In te grate d Badge contr ol Classic Desig ner In te grate d Remote contr ol 456 mm c avit y In te grate d Badge contr ol 456 mm c ...
Page 7 - CABINETRY DIMENSIONS; Cabinetry dimensions
7 5 CABINETRY DIMENSIONS min. 412mm 456mm 480mm L L L dishwasher dishwasher dishwasher Standard height models Tall height Classic models Tall height Integrated models Compact Oven Single Oven Tall height Designer models Plan Side L N M Cavity height options allow you to match dishwasher with your ca...
Page 8 - min. 2 mm ventilation gap with; FRONT PANEL SPECIFICATIONS
8 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WIDTH OF THE PANEL Measure A ( the width between adjacent door/drawer fronts) and write it in the fi rst box below, then complete the equation. HEIGHT OF THE PANEL Measure B and write it in th...
Page 9 - min. 8 mm ventilation gap
9 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WIDTH OF THE PANEL Measure A ( the width between adjacent door/drawer fronts) and write it in the fi rst box below, then complete the equation. HEIGHT OF THE PANEL Measure B and write it in th...
Page 10 - CAVITY PREPARATION; Water Connection; Water softener models; BENCHTOP
10 7a CAVITY PREPARATION Water Connection Recommended COLD (Maximum 60°C). ¾ “ BSP (GB20) to suit flat washer. Water Pressure Water softener models Max. 1 MPa (145 psi)Min. 0.1 MPa (14.5 psi) Models without water softener Max. 1 MPa (145 psi)Min. 0.03 MPa (4.3 psi) Important! Adjacent cabinetry must...
Page 11 - Shelf cutouts
11 7b 7c ø 60 mm ø 60 mm max. 5 mm max. 5 mm 220 mm 220 mm 100 mm 100 mm ø60mm Services can be located either side of dishwasher VENT HOSE VENT HOSE & SERVICES SERVICES Services can be located either side of dishwasher Shelf cutouts Shelf cutouts The ø60 mm services hole should be enlarged to ac...
Page 12 - MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE; Left hand side
12 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE Left hand side Right hand side Drain hose - 2000 mm Inlet hose - 1650 mm Venting hose - 1525 mm (Integrated wireless models only) (Integrated wireless models only) Venting hose - 1925 mm Power cord (excl. plug) - 1650 mm Drain hose - 1800 m...
Page 14 - ATTACH SIDE MOUNTING BRACKETS; ATTACH VENTING HOSE
14 RECOMMENDED METHOD (a) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY) 11a 10a ATTACH SIDE MOUNTING BRACKETS Fitted Elbow Clip all four side mountingbrackets into their slotsusing a flat-bladedscrewdriver. Ensure they’resecurely fitted beforesliding product into cavity. The mounting sl...
Page 15 - Airflow; INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - SECURE THE EXTERNAL VENT
15 12a 13a PULL THROUGH HOSES & MOVE INTO THE CAVITY SECURE THE DRAWER As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. Important! If product cannot be pushed in far enough, pull out again and rearrange hoses and cord. Do not use excessive force, as...
Page 16 - PULL THROUGH HOSES & MOVE INTO THE CAVITY
16 11b 10b PULL THROUGH HOSES & MOVE INTO THE CAVITY Fitted Elbow Check that the fitted elbow is rotated left or right (depending on the direction of the routing), then ensure the venting hose is securely attached to it. vent either through same cabinet or adjacent cabinet as perstep 7b or 7c AL...
Page 17 - SECURE THE EXTERNAL VENT
17 12b 13b 14b 15b REMOVE THE DRAWER SECURE THE DRAWER TO THE CABINETRY REFIT THE DRAWER ONTO THE RUNNERS 2 1 4 5 3 Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward. Ensure the release tabs on both sides are reset full...
Page 18 - EARTH THE PANEL
18 1 2 16 mm x6 2 2 1 Important! Ensure the rubber seal between the drawer and panel is kept in place. REMOVE BRACKET FROM PRODUCT ATTACH PANEL TO PRODUCT ATTACH PANEL TO PANEL BRACKET There must be at least 3 screws used each side When refitting the door pins, ensure they are orientated as shown. A...
Page 19 - ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS
19 ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS With the front panel fitted, insert an appropriately sized Philips screwdriver into the hole above the door pin and rotate the panel up or down to align the gaps in your cabinetry. Repeat on the other side if necessary. The panel has a maximum trave...
Page 21 - REATTACH BADGE & EARTH THE PANEL
21 2 2 1 ATTACH PANEL TO PRODUCT ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS 20b 22b 21b With the front panel fitted, insert an appropriately sized Philips screwdriver into the hole above the door pin and rotate the panel up or down to align the gaps in your cabinetry. Repeat on the other side i...
Page 22 - Dishwasher using sink trap with drain hose joiner; Dishwasher and Standpipe Ø 38; mm; CONNECT INLET HOSE TO COLD WATER; see
22 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. 23 1 3 2 750-882.5 mm 1 2 38 mm max. 120 mm 750-882.5 mm * * 3 4 5 If space is limited for fixing, push hose through drain hose support to required height If space is limited for fixing, push hose through drain ...
Page 23 - SAVE THESE INSTRUCTIONS
23 27 26 FINAL CHECKLIST TROUBLESHOOTING Check all parts are installed.Ensure that all panels and parts thereof are secure and final electrical tests have been conducted in accordance with local electrical regulations. Ensure product is level, securely fastened to the cabinetry and opens and closes ...
