Extron TPS150 - Manual

Table of Contents:

• Page 2 – Precautions; ᅝܼ乏ⶹ; 䄺ਞ
• Page 3 – TPS150 Switching and Transmission System • Quick Start; Quick Start — TPS150 Switching; Installation; Inputs 1 and 2 —; Connect
• Page 4 – Quick Start — TPS150 Switching and Transmission System; Setup and Operation; Input and projector codes
• Page 5 – TPS150 Switching and Transmission System • Table of Contents; Table of Contents; Chapter 1 • Introduction
• Page 6 – Table of Contents, cont’d; Chapter 4 • Serial Communications; ICS100 Windows-Based Control Program; Appendix A • Reference Information; Specifications
• Page 7 – TPS150 Switching and Transmission System; Chapter One; Introduction; About this Manual
• Page 8 – TPS150 Switching and Transmission System • Introduction; About the TPT150 switching transmitter; Input 1 and input 2 —
• Page 9 – About the TPR150 receiver; High-resolution RGB video; on one female 15-pin HD connector; Composite video; on one female RCA connector
• Page 10 – TP Cable Advantages; Transmission distance; Recommended transmission ranges at 60 Hz; Video format; Features; Provides for local monitor output on a
• Page 11 – Audio output volume adjustment and muting —; The output has volume control; Control —; The front panel controllers include attachment; Optional CTP150CM control panel —; Seven soft-touch buttons control the input
• Page 13 – Chapter Two; Mounting the Transmitter and Receiver
• Page 14 – Rack mounting the transmitter; UL requirements; Elevated operating ambient temperature —; Mounting instructions; Figure 2-1 — Mounting the transmitter
• Page 15 – TPS150 Switching and Transmission System • Installation; Projector mounting the receiver; If desired, projector mount the receiver as follows:; Figure 2-2 — Projector mounting the receiver
• Page 16 – Cabling and Rear Panel Views; Transmitter connections; Figure 2-3 — TPT150 transmitter rear panel connectors; Video and audio input connections; Input 1 and Input 2 RGB/VGA video connectors —; Figure 2-4 — Input 3 and input 4 video format connections; Input audio connectors —
• Page 17 – Output UTP Link connector —; Connect one end of a TP cable to this RJ-45; Output Audio connector —; Connect an audio device, such as powered; Figure 2-5 — Wiring the audio output connector; . Longer bare wires can short together. Shorter; Remote control connections; Contact Closure —; If desired, connect an optional
• Page 18 – Connect a host device, such as a computer or touch panel; — Remote port pin assignments for the TPT150 and TPR150; Power connection; AC power switch —; Toggle the AC power switch to the on ( ) position to turn; AC power connector —; Plug a standard IEC power cord into this connector; Receiver connections; Figure 2-7 — TPR150 receiver rear panel connectors; UTP Link Input connection; Input UTP Link connector —; Connect the free end of the TP cable from the
• Page 19 – RGB/VGA video connector —; Serial connection
• Page 20 – TP Cable Termination; Figure 2-8 — TP cable termination
• Page 21 – Chapter Three; Operation; Controls and Indicators
• Page 22 – TPS150 Switching and Transmission System • Operation; Transmitter controls and indicators; Figure 3-1 — TPT150 transmitter front panel; Power LED —; When lit, the Power LED indicates that power is applied to the; Input Select buttons —; The Input 1 Select through Input 4 Select buttons; Blank button and LED —; Press the Blank button to toggle video mute on and; Projector Power button and LED —; Press the Projector Power button to
• Page 23 – Receiver controls and indicators; Figure 3-2 — TPR150 receiver front panel
• Page 24 – Operations; Power
• Page 25 – Volume adjustment; Output volume —; Full system reset
• Page 26 – Optimizing the Video; Select the highest resolution.; Repeat steps 4 through 6 to fine tune the adjustments.
• Page 27 – Troubleshooting; The following tips may help you in troubleshooting.; General checks; Ensure that the input selected is active.
• Page 28 – Specific problems; Problem
• Page 29 – Chapter Four; Serial Communications
• Page 30 – Serial Communications, cont’d; System requirements; Operating system; If you are using Windows NT, Service Pack 6 must be installed.; Hardware; Installing the software
• Page 31 – Establishing communications with the program; Figure 4-1 — ICS100 program window and connected message
• Page 32 – Figure 4-3 — Serial Port setup window
• Page 34 – Using the software to configure the serial port settings; Figure 4-6 — Serial Port Setup window
• Page 35 – Using the software to program the input and projector codes; Figure 4-7 — Program Projector Codes window; For each input or projector code to be programmed; Input 1 through 4 code
• Page 36 – Figure 4-11 — Unprintable codes
• Page 37 – Repeat step 2 for each button or code to be programmed.; Click in the upper right corner of the window to close the window.; Using the software to operate the transmission system; Use the control program to operate the transmitter as follows:
• Page 38 – The; Using the help system; From the ICS100 startup window, select Help from the Help menu.
• Page 39 – Serial Commands; Communication protocols; Command and response structure; Example; Addressing the transmitter
• Page 40 – Transmitter responses; Symbols
• Page 41 – Spaces between bytes are not allowed.
• Page 42 – Command/response table for programming and operating the TPT150; Command; Addressing
• Page 43 – Input audio level; Output level; Program projector power and input command codes
• Page 44 – Program projector power and input command codes (continued)
• Page 45 – Front panel lockout
• Page 47 – Appendix A; Reference Information
• Page 48 – Video; Video output
• Page 50 – Reference Information, cont’d; General; Specifications are subject to change without notice.
• Page 51 – Part Numbers; These items are included in each order for a TPS150:; Included parts; Optional accessories; Accessory