Extron TPS150 - Manuals - manualsarea.com

Page 2 - Precautions; ᅝܼ乏ⶹ; 䄺ਞ

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk o...

Page 3 - TPS150 Switching and Transmission System • Quick Start; Quick Start — TPS150 Switching; Installation; Inputs 1 and 2 —; Connect

QS-1 TPS150 Switching and Transmission System • Quick Start Quick Start — TPS150 Switching and Transmission System Installation Step 1 Turn off power to the input and output devices,and remove the power cords from them. Step 2 If desired, mount the TPT150 transmitter in arack. Step 3 If desired, mou...

Page 4 - Quick Start — TPS150 Switching and Transmission System; Setup and Operation; Input and projector codes

Quick Start — TPS150 Switching and Transmission System TPS150 Switching and Transmission System • Quick Start QS-2 Step 10 Connect a projector or plasma display to thereceiver ’s video outputs. Output 1 — Connect a VGA cable between the15-pin HD femaleconnector and the VGA or RGB input on thedisplay...

Page 5 - TPS150 Switching and Transmission System • Table of Contents; Table of Contents; Chapter 1 • Introduction

i TPS150 Switching and Transmission System • Table of Contents Table of Contents Chapter 1 • Introduction ....................................................................................................... 1-1 About this Manual .......................................................................

Page 6 - Table of Contents, cont’d; Chapter 4 • Serial Communications; ICS100 Windows-Based Control Program; Appendix A • Reference Information; Specifications

ii TPS150 Switching and Transmission System • Table of Contents Table of Contents, cont’d All trademarks mentioned in this manual are the properties of their respective owners. 68-958-01 Rev. C 10 06 Chapter 4 • Serial Communications .....................................................................

Page 7 - TPS150 Switching and Transmission System; Chapter One; Introduction; About this Manual

TPS150 Switching and Transmission System 1 Chapter One Introduction About this Manual About the Transmission System TP Cable Advantages Features

Page 8 - TPS150 Switching and Transmission System • Introduction; About the TPT150 switching transmitter; Input 1 and input 2 —

Introduction, cont’d TPS150 Switching and Transmission System • Introduction 1-2 Introduction About this Manual This manual contains installation, configuration, and operating information for theExtron TPS150 audio/video Twisted Pair (TP) switching and transmission system. • Chapter 1 identifies the...

Page 9 - About the TPR150 receiver; High-resolution RGB video; on one female 15-pin HD connector; Composite video; on one female RCA connector

1-3 TPS150 Switching and Transmission System • Introduction The audio for the selected input is output locally. It is not sent to the receiver. The TPT150 has an RS-232 port that accepts ICS100 program control from aconnected computer or serial command control from a computer or control system.The t...

Page 10 - TP Cable Advantages; Transmission distance; Recommended transmission ranges at 60 Hz; Video format; Features; Provides for local monitor output on a

Introduction, cont’d TPS150 Switching and Transmission System • Introduction 1-4 TP Cable Advantages Twisted pair cable is much smaller, lighter, more flexible, and less expensive thancoaxial cable. The TPT150 makes cable runs simpler and less cumbersome.Termination of the cable with RJ-45 connector...

Page 11 - Audio output volume adjustment and muting —; The output has volume control; Control —; The front panel controllers include attachment; Optional CTP150CM control panel —; Seven soft-touch buttons control the input

1-5 TPS150 Switching and Transmission System • Introduction Audio output volume adjustment and muting — The output has volume control adjustment via the front panel, RS-232 control, or optional contact closurepanel control. Control — Switcher control is available through the front panel, an RS-232 p...

Page 13 - Chapter Two; Mounting the Transmitter and Receiver

TPS150 Switching and Transmission System 2 Chapter Two Installation Mounting the Transmitter and Receiver Cabling and Rear Panel Views TP Cable Termination

Page 14 - Rack mounting the transmitter; UL requirements; Elevated operating ambient temperature —; Mounting instructions; Figure 2-1 — Mounting the transmitter

Installation, cont’d TPS150 Switching and Transmission System • Installation 2-2 Installation Mounting the Transmitter and Receiver The TPS150 comes with rubber feet for the transmitter and receiver, a set ofMTR102 rack ears for the transmitter, and a set of mounting brackets for thereceiver. Rack m...

Page 15 - TPS150 Switching and Transmission System • Installation; Projector mounting the receiver; If desired, projector mount the receiver as follows:; Figure 2-2 — Projector mounting the receiver

2-3 TPS150 Switching and Transmission System • Installation 3 . Insert the transmitter into the rack, aligning the holes in the mounting bracketwith those of the rack. 4 . Secure the transmitter to the rack using the supplied machine screws. Projector mounting the receiver If desired, projector moun...

Page 16 - Cabling and Rear Panel Views; Transmitter connections; Figure 2-3 — TPT150 transmitter rear panel connectors; Video and audio input connections; Input 1 and Input 2 RGB/VGA video connectors —; Figure 2-4 — Input 3 and input 4 video format connections; Input audio connectors —

Installation, cont’d TPS150 Switching and Transmission System • Installation 2-4 Cabling and Rear Panel Views Transmitter connections All connectors are on the rear panel (figure 2-3). + - + R L - G N D P RO J P W R VO L D N VO L U P I N 4 I N 3 I N 2 I N 1 L O C A L M O N I TO R O U T P U T AU D I ...

Page 17 - Output UTP Link connector —; Connect one end of a TP cable to this RJ-45; Output Audio connector —; Connect an audio device, such as powered; Figure 2-5 — Wiring the audio output connector; . Longer bare wires can short together. Shorter; Remote control connections; Contact Closure —; If desired, connect an optional

2-5 TPS150 Switching and Transmission System • Installation TP and audio output connections 5 Output UTP Link connector — Connect one end of a TP cable to this RJ-45 female connector on the transmitter. Connect the free end of the same TP cable from the transmitter to the RJ-45female connector on th...

Page 18 - Connect a host device, such as a computer or touch panel; — Remote port pin assignments for the TPT150 and TPR150; Power connection; AC power switch —; Toggle the AC power switch to the on ( ) position to turn; AC power connector —; Plug a standard IEC power cord into this connector; Receiver connections; Figure 2-7 — TPR150 receiver rear panel connectors; UTP Link Input connection; Input UTP Link connector —; Connect the free end of the TP cable from the

Installation, cont’d TPS150 Switching and Transmission System • Installation 2-6 8 RS-232 port — Connect a host device, such as a computer or touch panel control, to the TPT150 transmitter via this 9-pin D connector and a nullmodem serial port cable for serial RS-232 control (figure 2-6). Connected ...

Page 19 - RGB/VGA video connector —; Serial connection

2-7 TPS150 Switching and Transmission System • Installation Video output connections 12 RGB/VGA video connector — Connect a VGA cable between this 15-pin HD female connector and the VGA or RGB input on the display. 13 Composite video connector — Connect a video cable between this BNC female connecto...

Page 20 - TP Cable Termination; Figure 2-8 — TP cable termination

Installation, cont’d TPS150 Switching and Transmission System • Installation 2-8 TP Cable Termination RJ-45 termination must comply with the TIA/EIA T 568A or TIA/EIA T 568Bwiring standards for all connections. The TPS150 works with either shielded or unshielded cables. However, tocomply with FCC ru...

Page 21 - Chapter Three; Operation; Controls and Indicators

TPS150 Switching and Transmission System 3 Chapter Three Operation Controls and Indicators Operations Optimizing the Video Troubleshooting

Page 22 - TPS150 Switching and Transmission System • Operation; Transmitter controls and indicators; Figure 3-1 — TPT150 transmitter front panel; Power LED —; When lit, the Power LED indicates that power is applied to the; Input Select buttons —; The Input 1 Select through Input 4 Select buttons; Blank button and LED —; Press the Blank button to toggle video mute on and; Projector Power button and LED —; Press the Projector Power button to

Operation, cont’d TPS150 Switching and Transmission System • Operation 3-2 Operation Controls and Indicators Transmitter controls and indicators The TPT150 transmitter will not operate properly unless it is connected to apowered TPR150 receiver. All of the transmitter’s controls are on the front pan...

Page 23 - Receiver controls and indicators; Figure 3-2 — TPR150 receiver front panel

3-3 TPS150 Switching and Transmission System • Operation 5 Volume up and down buttons — The Volume up ( ) and Volume down ( ) buttons are used to increase and decrease the output volume and the selectedinput’s audio level. See “Volume adjustment” on page 3-5 for more details. The Volume buttons are ...

Page 24 - Operations; Power

Operation, cont’d TPS150 Switching and Transmission System • Operation 3-4 Operations The following paragraphs detail the power-up process and then describe selectingan input, issuing the projector power up and down commands, and adjusting theinput level and output volume. Power Apply power to the t...

Page 25 - Volume adjustment; Output volume —; Full system reset

3-5 TPS150 Switching and Transmission System • Operation Press the Projector Power button on the transmitter to issue the projector on or offcommand. When you push the button, the following occurs: • If no command has been transmitted since transmitter power was applied, orif the power off command w...

Page 26 - Optimizing the Video; Select the highest resolution.; Repeat steps 4 through 6 to fine tune the adjustments.

Operation, cont’d TPS150 Switching and Transmission System • Operation 3-6 Optimizing the Video The TPR150 receiver features cable equalization controls for high and lowfrequency adjustments and RGB skew control to compensate for misconvergence ofcolors that can result from long CAT 5 cable runs. Th...

Page 27 - Troubleshooting; The following tips may help you in troubleshooting.; General checks; Ensure that the input selected is active.

3-7 TPS150 Switching and Transmission System • Operation Troubleshooting This section gives recommendations on what to do if you have problems operatingthe transmitter/receiver system, and it provides examples and descriptions forsome image problems you may encounter. The following tips may help you...

Page 28 - Specific problems; Problem

Operation, cont’d TPS150 Switching and Transmission System • Operation 3-8 Specific problems The table below shows some common operating problems and their solutions. Problem Possible cause Solution No image appears. System is not receiving Ensure that the video source, thepower. transmitter and rec...

Page 29 - Chapter Four; Serial Communications

TPS150 Switching and Transmission System 4 Chapter Four Serial Communications ICS100 Windows-Based Control Program Serial Commands

Page 30 - Serial Communications, cont’d; System requirements; Operating system; If you are using Windows NT, Service Pack 6 must be installed.; Hardware; Installing the software

Serial Communications, cont’d TPS150 Switching and Transmission System • Serial Communications 4-2 Serial Communications The transmitter must be programmed with commands to be sent upon inputselection and with projector power on/off commands before those commands aresent. The transmitter can also be...

Page 31 - Establishing communications with the program; Figure 4-1 — ICS100 program window and connected message

4-3 TPS150 Switching and Transmission System • Serial Communications Establishing communications with the program The TPT150 transmitter will not operate properly unless it is connected to apowered TPR150 receiver. Start the control program and establish communications with the TPT150 asfollows: 1 ....

Page 32 - Figure 4-3 — Serial Port setup window

Serial Communications, cont’d TPS150 Switching and Transmission System • Serial Communications 4-4 The transmitter’s serial port is factory-configured to 9600 baud, no parity, noflow control, half-duplex mode. If desired, the computer’s serial port settingscan be changed from within the ICS100 progr...

Page 34 - Using the software to configure the serial port settings; Figure 4-6 — Serial Port Setup window

Serial Communications, cont’d TPS150 Switching and Transmission System • Serial Communications 4-6 Using the software to configure the serial port settings If necessary, use the ICS 100 software to change the serial port settings of either thetransmitter or receiver. The transmitter’s serial port is...

Page 35 - Using the software to program the input and projector codes; Figure 4-7 — Program Projector Codes window; For each input or projector code to be programmed; Input 1 through 4 code

4-7 TPS150 Switching and Transmission System • Serial Communications Using the software to program the input and projector codes Use the control program to program the transmitter ’s input selection and projectorpower on/off buttons as follows: 1 . Click Controls > Projector Codes > Input Code...

Page 36 - Figure 4-11 — Unprintable codes

Serial Communications, cont’d TPS150 Switching and Transmission System • Serial Communications 4-8 c . Enter the desired code in the code window (figure 4-9). Spaces are ok when you are entering ASCII codes. Figure 4-9 — Code entry (ASCII code) Codes that are intended to be hex codes must be in pair...

Page 37 - Repeat step 2 for each button or code to be programmed.; Click in the upper right corner of the window to close the window.; Using the software to operate the transmission system; Use the control program to operate the transmitter as follows:

4-9 TPS150 Switching and Transmission System • Serial Communications 3 . Repeat step 2 for each button or code to be programmed. 4 . Click in the upper right corner of the window to close the window. 5 . Click Controls > Projector Codes > Projector Delay. The Program Projector Delaywindow appe...

Page 38 - The; Using the help system; From the ICS100 startup window, select Help from the Help menu.

Serial Communications, cont’d TPS150 Switching and Transmission System • Serial Communications 4-10 2 . With the exception of input audio level, the controls on the control panelwindow operate the same as the physical front panel of the transmitter. Seechapter 3, Operation. If you click the Projecto...

Page 39 - Serial Commands; Communication protocols; Command and response structure; Example; Addressing the transmitter

4-11 TPS150 Switching and Transmission System • Serial Communications Serial Commands Communication protocols The transmitter ’s and receiver ’s serial ports (figure 4-16) are factory-configured to9600 baud, no parity, no flow control, half-duplex mode. If you change thetransmitter ’s serial protoco...

Page 40 - Transmitter responses; Symbols

Serial Communications, cont’d TPS150 Switching and Transmission System • Serial Communications 4-12 When the system is in Pass-Through mode [CC98], commands and responses aresent between the transmitter and receiver. If the system is not in Pass-Throughmode, all of the receiver responses to the tran...

Page 41 - Spaces between bytes are not allowed.

4-13 TPS150 Switching and Transmission System • Serial Communications X2 = Input number 01 – 04 X3 = On/off status 0 = off, 1 = on X4 = Input volume –15 (dB) of attenuation (minimum volume) through 00 (dB) (maximum volume) X5 = Output level –31 (dB) of attenuation (maximum attenuation) through 20 (d...

Page 42 - Command/response table for programming and operating the TPT150; Command; Addressing

Serial Communications, cont’d TPS150 Switching and Transmission System • Serial Communications 4-14 Command/response table for programming and operating the TPT150 Command ASCII Command Response Additional description (host to TPT150) (TPT150 to host) Addressing Connect [CC X1 ] {none} Connect the h...

Page 43 - Input audio level; Output level; Program projector power and input command codes

4-15 TPS150 Switching and Transmission System • Serial Communications Command/response table for programming and operating the TPT150 (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) Input audio level Adjust the input audio level [VIN X2 X4 0] [R0•...

Page 44 - Program projector power and input command codes (continued)

Serial Communications, cont’d TPS150 Switching and Transmission System • Serial Communications 4-16 Command/response table for programming and operating the TPT150 (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) Program projector power and input c...

Page 45 - Front panel lockout

4-17 TPS150 Switching and Transmission System • Serial Communications Command/response table for programming and operating the TPT150 (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) Front panel lockout Disable front panel [FP0] [R0• X1 •FP0•] Disa...

Page 47 - Appendix A; Reference Information

TPS150 Switching and Transmission System A Appendix A Reference Information Specifications Part Numbers

Page 48 - Video; Video output

TPS150 Switching and Transmission System • Reference Information A-2 Reference Information Specifications Video Gain ................................................ UnityCrosstalk ....................................... -42 dB @ 10 MHzNumber/signal type ................... 1 set of proprietary anal...

Page 50 - Reference Information, cont’d; General; Specifications are subject to change without notice.

Reference Information, cont’d TPS150 Switching and Transmission System • Reference Information A-4 Program control .......................... Inline Control Software for Windows ® – lCS100 Control — projector (TPR only) Projector control port ................. RS-232, 9-pin male D connectorBaud rate...

Page 51 - Part Numbers; These items are included in each order for a TPS150:; Included parts; Optional accessories; Accessory

A-5 TPS150 Switching and Transmission System • Reference Information Part Numbers Included parts These items are included in each order for a TPS150: Included parts Part number TPS150 twisted pair (TP) switching and transmission system 70-369-01 TPT150 switching transmitter 60-575-01 TPR150 receiver...