Page 2 - Precautions; 安全须知; 注意
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product enclosure that may present a risk of ...
Page 3 - FCC Class A Notice; This device may not cause harmful interference.; click here; A note draws attention to important information.; Copyright; © 2010 Extron Electronics. All rights reserved.; Trademarks
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interferen...
Page 5 - Contents
Contents Introduction ............................................ 1 About the TLP 700MV and TLP 700TV ............. 1Features ........................................................... 2Requirements ................................................... 3 Software .......................................
Page 7 - Introduction; mounted on a wall or furniture, using the
Introduction This guide describes the function, installation and operation of the TouchLink TLP 700MV and TLP 700TV panels. The guide also provides information about optional accessories that are available from Extron for both panels.Unless otherwise stated, the terms “TLP 700 series” and “TLP 700” ...
Page 8 - Features
100-240V 50-60H z INPUT VID VID YC Y B-Y R-Y RGB DVI 8 1 2 4 5 3 L 2 1 3 4 5 6 7 R AUDIO INPU T L A B RS -23 2 R OUTPUT L R OUTPUT RGB Y, B-Y , R-Y 8 7 RGB 6 L I S T E D 1 T 2 3 I . T . E . C U S INPUT LAN POWER12V500mAMA X 1 2 3 4 CO M 3 IR 3 S G S G TX RX 4 RE LA Y 3 4 CO M1 TX RX RT SC TS CO M 2 ...
Page 9 - Requirements; Software
Multiple mounting options — The TLP 700MV can be wall-mounted, rack-mounted, or furniture-mounted.The TLP 700TV comes with a stand that allows it to be placed on a desktop. If the stand is removed, the unit can be VESA-mounted on a wall or furniture using either of the optional Extron kits.See the l...
Page 10 - Panel Features; TLP 700MV Front Panel Features and Operations; Extron Global Configurator
Panel Features This section describes: TLP 700MV Front Panel Features and OperationsTLP 700MV Rear Panel Features and ConnectionsTLP 700TV Front Panel Features and OperationsTLP 700TV Rear Panel Features and Connections TLP 700MV Front Panel Features and Operations LIGHTS ON DISPLAY MUTE AUDIO MUTE ...
Page 11 - shuts down and restarts the unit without changing any of the; Reset button —; information see “; activates the; Reset LED —; for the Reset modes. For further information see “; Reset Modes
There are three buttons recessed behind the bezel. These buttons are used to configure the unit and reset parameters to factory defaults: LIGHTS ON DISPLAY MUTE AUDIO MUTE SPEECH MUTE AUTO IMAGE FREEZE LIGHTS OFF SCREEN SCREEN HELP ? 7 8 9 10 Figure 3. TLP 700MV Front Panel with Bezel removed g Rebo...
Page 12 - TLP 700MV Rear Panel Features and Connections; TLP 700MV Rear Panel Features; Connect the two pole, 3.5 mm captive screw connector from; Power Supply Connection
TLP 700MV Rear Panel Features and Connections 11 12 13 Figure 4. TLP 700MV Rear Panel Features k Power Connector — Connect the two pole, 3.5 mm captive screw connector from the provided power supply to the power supply socket on the rear panel. Ensure the connections have the correct polarity as sho...
Page 13 - Video Input —; Connect an S-video or composite video source; Network Connector —; The TLP 700MV connects to an Ethernet; Suggested models; are listed on page 3
NOTES: The length of the exposed wires in the stripping process is critical. The ideal length is 3/16 inches (5 mm). Any longer and the exposed wires may touch, causing a short circuit between them. Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws. Do...
Page 14 - TLP 700TV Front Panel Features and Operations
TLP 700TV Front Panel Features and Operations 1 4 5 6 2 3 78 9 Figure 6. TLP 700TV Front Panel Features a Buttons — These ten backlit push-buttons (five on either side of the screen) can be configured to execute user-defined functions using the Extron Global Configurator software (page 25). For info...
Page 15 - TLP 700TV Rear Panel Features and Connections; With Stand Attached; TLP 700TV Rear Features
TLP 700TV Rear Panel Features and Connections With Stand Attached 10 13 11 12 Figure 7. TLP 700TV Rear Features The following connections are available through the back panel when the stand is in place: j LED lights — The Link LED lights green to indicate a good network connection. The Activity LED ...
Page 16 - The TLP 700TV stand, which can be removed for VESA mounting, has:; Three adjustable potentiometers —; These are used to control sharpness and gain; TLP 700TV Potentiometers; When RJ-45 connectors are covered; see figure 7
TLP 700TV Base Features 17 C Gain Vid / Y Gain Sharp 33-1814-01 A 19 18 Figure 8. TLP 700TV Base Features The TLP 700TV stand, which can be removed for VESA mounting, has: q Three adjustable potentiometers — These are used to control sharpness and gain for both S-video luminance (Y) and S-video chro...
Page 17 - Initial Calibration; How to Access the Internal On-screen Menus; Menu; Main; Exit; Main Screen; Down
Initial Calibration This section describes: z z How to Access the Internal On-screen Menus z z The Main , Volume , Time , Network , and Video Screens z z The Screen Touch Calibration Screen How to Access the Internal On-screen Menus When power is first applied to the TouchLink Panel, the unit boots ...
Page 18 - Volume Screen
When Auto Backlight is set to Off, the Backlight option allows the backlighting to be set manually from 0 to 100%. Press the Down or Up buttons to highlight the Backlight options and use the volume control knob or press the Down or Up buttons to adjust the backlighting. The current value is shown ab...
Page 20 - Main screen
Video Screen The small gray rectangle provides a video preview window that allows the user to adjust the video properties.Click on the Down or Up buttons to highlight one of the adjustable video settings. Use the Down and Up buttons or the volume control knob to adjust: z z Contrast between 0 and 12...
Page 21 - Control Software; Software Overview; Design the layout of the text and graphics
Control Software This section of the guide discusses the software and firmware needed to set up the Touchpanel units: z z Software Overview z z Installing the Software z z Updating the Firmware z z Using the TouchLink Panel Web Pages z z Using GUI Configurator z z Using Global Configurator Software ...
Page 22 - Installing the Software; Installation from the Extron Disc; Extron Web Site Download Center
Installing the Software Installation from the Extron Disc Insert the disc provided into the DVD-ROM drive of the computer. If the setup program does not start automatically, run Launch.exe from the DVD-ROM directory in Windows My Computer . Select the Software tab, locate the GUI Configurator progra...
Page 23 - Updating the Firmware; Updating Firmware Using the Extron Firmware Loader Utility
Updating the Firmware Firmware for the TLP 700 can be upgraded using the Extron Firmware Loader or using your web browser . Before starting, consult your IT team and ensure that the TLP 700 has a unique IP address. Updating Firmware Using the Extron Firmware Loader Utility NOTES: To use this method,...
Page 24 - Updating Firmware From a Web Browser; TouchLink Panel web pages
Updating Firmware From a Web Browser NOTES: Your PC must have internet access and be on the same network as the TouchLink Panel. 1. On the Extron web site, select the Download tab and click on the Firmware option in the menu bar at the left of the screen (see Figure 10 on page 16). 2. Navigate to th...
Page 25 - Using the TouchLink Panel Web Pages; As seen; in the previous section; , the TLP 700MV and TLP 700TV TouchLink Panels have; Configuration; tab and select the; System Settings; settings; TLP 700 Configuration Tab: System Settings Page
Using the TouchLink Panel Web Pages As seen in the previous section , the TLP 700MV and TLP 700TV TouchLink Panels have default web pages that can be used to read and change the current settings of the panels. The web pages can be accessed as follows: 1. Open your browser and type the IP address of ...
Page 27 - Using GUI Configurator; in the; Help; To use the GUI Configurator program, follow these instructions:; GUI; dialog box in front.; GUI Configurator: Main and GUI Configurator Start Options
Using GUI Configurator This section provides an overview of the GUI Configurator program. For complete information about the program, consult the GUI Configurator help file (click on Contents in the Help menu or press the <F1> key while within the program). To use the GUI Configurator program,...
Page 32 - Using Global Configurator; Click on the GC3 desktop icon. The; box; Global Configurator 3 Start Options
Using Global Configurator NOTE: To configure a TouchLink Panel, you must use Global Configurator version 3.0 or later. This section provides an overview of the Global Configurator program. For complete information about the program, consult the Global Configurator help file (click on Contents in the...
Page 33 - Select; Create A New Project; and click; OK
2. Select Create A New Project and click OK . The dialog box closes, leaving the Project Settings screen. Figure 25. Global Configurator Project Settings 3. Enter the IP Address for the TLP 700MV panel.The default Telnet connection is port 23 and HTTP is port 80, so these values do not usually need ...
Page 35 - Click; and the; Add Device; Touchpanel Port 1; . The screen shows the available options for the; Click here to add one
5. Click OK and the Add Device screen closes. The start-up screen, which was behind it, is now visible. The device configuration tree, in the panel to the left of the main screen, shows the IPL 250 and the available ports: Figure 27. Configuring an IP Link Device 6. Select Touchpanel Port 1 . The sc...
Page 37 - Specifications; Display
Specifications TLP 700MV Display Screen type .................................... Active matrix TFT color displaySize ................................................ 7" (17.8 cm), measured diagonallyResolution ...................................... 800x480Dot/pixel pitch ..........................
Page 41 - Audio output
Audio input — see S-video or composite video MTP transmitters' specifications NOTE: Audio input is available only from an Extron MTP transmitter through the RJ-45 connector in the base of the unit. If the base is removed from the TLP 700TV, connections are via BNC connectors, and there is no audio i...
Page 43 - Included Parts; Setup Guide; Optional Parts; Description
Accessories and Part Numbers Included Parts Description Part Number TLP 700MV TouchLink Panel (wall mount) 60-546-0x TLP 700TV TouchLink Panel (desktop or VESA mount) 60-548-02 12 VDC, 1A power supply for TLP 700MV 70-775-01 12 VDC, 3A power supply for TLP 700TV 70-380-01 TR 700M trim ring (for TLP ...
Page 44 - Mounting; Underwriters Laboratories Guidelines for Rack Mounting; Elevated operating ambient temperature —; Rack Mounting the TLP 700MV
Mounting This section outlines the various options for: z z Rack Mounting the TLP 700MV z z Wall Mounting the TLP 700MV z z Wall Mounting the TLP 700MV with a Wallbox z z Desktop Mounting the TLP 700TV z z Removing the TLP 700TV base for VESA Mounting z z VESA mounting the TLP 700TV Rack Mounting th...
Page 45 - Wall Mounting the TLP 700MV; rear panel connectors
Wall Mounting the TLP 700MV The TLP 700MV can be mounted in the wall or through furniture. Extron recommends using the Extron TR 700M trim ring to conceal any ragged edges when the hole is cut in the wall or furniture.To mount the TLP 700MV directly into a wall, follow these steps. The steps are sim...
Page 46 - Secure the TLP 700MV to a Wall With Locking Arms; If required, perform the; initial calibration; Wall Mounting the TLP 700MV with a Wall Box; instructions provided with the wall box.
Trim Ring Screws (4) Tighten screws to rotate locking arms. Bezel snaps to unit (4 plcs ea side). Figure 31. Secure the TLP 700MV to a Wall With Locking Arms 11. If required, perform the initial calibration (see page 11). 12. Replace the bezel by pressing the catches on the bezel into the correspond...
Page 47 - Desktop Mounting the TLP 700TV; adjust the sharpness and gain; Removing the TLP 700TV Base for VESA Mounting; VESA B —
Desktop Mounting the TLP 700TV The TLP 700TV comes assembled with a stand that allows it to be placed on a desktop. If required, the stand can be removed and replaced with the Extron VM 700T kit (part number 70-692-01 ). This kit fits into any third-party VESA Type D 75 mm wall mount system.To mount...
Page 48 - Squeeze Sides of the Back Cover.
To prepare the TLP 700TV for wall mounting, using either kit, follow these instructions: 1. Remove the TLP 700TV from its packaging or, if the TLP 700TV has previously been used as a free-standing, desktop unit, remove all cables to the back of the base. 2. At the bottom, the two plastic cover plate...
Page 50 - Thread Cables into Place.
9. Thread the cables through the gap between the top bracket and the stand. Place the screen, face down, on a soft cloth. 9 Figure 44. Thread Cables into Place. 10. Remove and save the three Phillips head screws holding the plastic molding to the back of the screen. 10 Figure 45. Remove Molding. TLP...
Page 51 - VESA Mounting the TLP 700TV; previous section; ) or the Extron VM 700T mounting
11. Disconnect the audio, LED, and power cables from the back panel of the screen. z z The audio cables are the black and white pair, wound around a ferrite core. z z The power cables are the red and black pair, terminated with a blue, 2-pole captive screw connector. z z The LED cables are the black...
Page 52 - Reset button on the TLP 700MV; . The Reset button on the TLP 700TV is recessed behind; Reset button on the TLP 700TV; Use Factory Firmware
Reset Modes The TLP 700MV and TLP 700TV have four reset modes that correspond to four of the five reset modes for the IP Link controllers. The modes are initiated by pressing the Reset button.To access the Reset button on the TLP 700MV, remove the bezel. See page 5 to locate the Reset button on the ...
Page 53 - Button Labels; Button Label Software; Installing or Replacing Button Labels; see; Button Label Generator Software; com; ButtonLabelGenerator
Button Labels This section provides information about: z z Button Label Software z z Replacing Button Labels Button Label Software Installing or Replacing Button Labels Printed labels are included with the TLP 700MV and TLP 700TV. In addition, users can write on blank labels, purchase additional she...
Page 54 - Using the Button-Label Generator software; Generator > Button Label Generator; Click the; Clear All Buttons; button and create new labels as many times as
Using the Button-Label Generator software 1. To run the Button-Label Generator program, click on the desktop icon. Alternatively, click Start > Programs > Extron Electronics > Button Label Generator > Button Label Generator . The Button-Label Generator window appears: Figure 47. Button L...
Page 55 - Replacing Button Labels; Removing Buttons; Repeat steps
Replacing Button Labels The illustration below shows how to replace the button labels on the TLP 700MV. Although, the buttons on the TLP 700TV are slightly smaller and the labels are different dimensions, the procedure for replacing labels on either model is the same. To change the translucent butto...
Page 57 - USA; xtron
Extron ® Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase; touchscreen display and overlay components are covered for 1 year. In the event of malfunction during the warranty period attributable direct...
Page 58 - Installation Checklist; Step 3 — Initial configuration with internal on-screen menus:
Extron USA - West Headquarters + 800.633.9876 Inside USA/Canada Only +1.714.491.1500+1.714.491.1517 FAX Extron USA - East +800.633.9876 Inside USA/Canada Only +1.919.863.1794+1.919.863.1797 FAX Extron Europe +800.3987.6673 Inside Europe Only +31.33.453.4040+31.33.453.4050 FAX Extron Asia +800.7339.8...
