Extron RCP 2000 - Manual
Extron RCP 2000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Precautions; Safety Instructions • English; FCC Class A Notice; Extron’s Warranty
- Page 3 – RCP 2000 • Quick Start Guide; Turn the equipment off; and disconnect it from the power source.; Set; the RCP 2000 on a table or other flat surface.; one of the RS-232 cables provided with the RCP 2000 between; one of the RS-232 cables provided with the RCP 2000 between; Quick Start Guide — RCP 2000
- Page 4 – Quick Start Guide — RCP 2000, cont’d; iii; Chapter 1 • Introduction; Table of Contents; Continue
- Page 5 – Table of Contents, cont’d; RCP 2000 Remote Control Panel; Network Switcher Control; Chapter One; Introduction; Features
- Page 6 – Chapter Two; Installation; Rear Panel Connectors; Applying and Changing a
- Page 7 – AC power connector —; Resetting the Unit
- Page 8 – Application Example; Figure 2-2 — RCP 2000 application example; Making an RCP Communication Cable
- Page 9 – Chapter Three; Operation; Top Panel Controls; crossover cable; . See the table on the next; When connecting the RCP 2000; patch; table below for RJ-45 patch cable connections.
- Page 10 – Applying and Changing a Switching Effect
- Page 11 – Take button —; Applying and Changing a Switching; Picture control buttons —; Using the Picture; Using the Picture Controls; Adjusting color and tint
- Page 12 – Detail adjustments; Cuts; Implementing an effect; Figure 3-2 — A dissolve effect; Changing the duration of a dissolve; Figure 3-3 — Standard wipe transitions
- Page 13 – Plus wipe; causes the preview image to appear to unroll over; Square wipe; causes the preview image to appear to unroll; Title; causes a predefined box in the program image to dissolve; Selecting a wipe and a wipe duration
- Page 14 – Figure 3-8 — Available wipes; Implementing a title; CAUTION; — Pressing and; holding; holding
- Page 15 – Chapter Four; Remote Control; Manual IP Setup
- Page 16 – Changing the IP addresses; To change the IP addresses:; Figure 4-1 — Setting up for an IP address change; Figure 4-2 — Making the IP address change
- Page 17 – Contacting the RCP unit; Logon and system status; Enter the IP address of the unit (see; Establishing or changing system settings; To change system settings:
- Page 18 – Remote Control, cont’d; Figure 4-4 — System Settings screen; Firmware upgrade; From the Configuration tab, click on
- Page 19 – File management; Figure 4-6 — File Management screen; Accessing network switcher control; Changing the IP
- Page 20 – Appendix; Accessories; Specifications; Figure 4-7— ISS Control screen; Using network switcher control; To use network switcher control, follow these steps:
- Page 21 – Part Numbers; Extron Part; Control/remote — control panel; autodetect; General; internal, autoswitchable; Specifications are subject to change without notice.
- Page 23 – RCP 2000 • Specifications, Parts, and Accessories
User’s Manual
© 2005 Extron Electronics. All rights reserved.
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
www.extron.com
Remote Control Panel
68-792-01
Rev. C
03 05
RCP 2000
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Precautions This symbol is intended to alert the user of importantoperating and maintenance (servicing) instructionsin the literature provided with the equipment. This symbol is intended to alert the user of thepresence of uninsulated dangerous voltage withinthe product's enclosure that may present ...
RCP 2000 • Quick Start Guide Step 1 Turn the equipment off and disconnect it from the power source. Make sure that the ISS 108/408 or SGS 408 and all attached devicesare turned off and, if applicable, disconnected from the powersource. Step 2 Set the RCP 2000 on a table or other flat surface. Step 3...
RCP 2000 • Quick Start Guide Quick Start Guide — RCP 2000, cont’d iii RCP 2000 • Table of Contents Chapter 1 • Introduction .......................................................... 1-1 Features ...................................................................................... 1-2 Chapter 2 • I...
