Extron PVS 300 - Manual

Table of Contents:

• Page 2 – Precautions; 安全须知; 注意
• Page 3 – PoleVault Systems Installation • Introduction; Introduction; Overview; This manual covers the installation of the Extron PoleVault; in a drop ceiling room with a wood or concrete; The PoleVault System; FCC Class A Notice; the interference at his own expense.
• Page 4 – Extron PoleVault; Extron Cables & Notes; PoleVault System installation and wiring overview
• Page 5 – PoleVault Systems Installation • Introduction — Planning; Before you Begin Installation - Planning; that key aspects have been considered.; Typical classroom installation
• Page 6 – Introduction — Planning, cont’d; Type and control (important for projector image viewing); Example classroom installation; b. Location of the screen and projector; Aligned with center of the screen. Not an obstruction to viewing; ADA overhead and side clearance requirements
• Page 7 – • Viewing obstructions; c. Location of MediaLink Controller and Wall Plates; • Forward and side reach (for full details refer to a copy of; Wall or floor cabled; d. Type and location of the speakers; Based on ceiling height and room size; Example classroom with four speaker installation
• Page 8 – Introduction — Inventory Overview; PoleVault System Devices and Hardware; PMP; hardware, individually boxed and labeled.; PoleVault A/V Source Input Wall Plates, and are shipped as follows:
• Page 9 – PoleVault System Devices and Hardware, cont’d
• Page 10 – PoleVault System Ceiling Speakers
• Page 11 – b. Items not included
• Page 12 – d. Installation tools; Tools should include, but are not confined to:
• Page 13 – PoleVault Systems Installation • Installation Overview; Installation Overview; in five sections, Stages One though Five.; Outline of installation steps; — Install the PV SI 3C LP Ceiling Speakers.
• Page 14 – PoleVault Systems Installation • Installation — Stage 1; Stage One — Install the Screen and Projector; Stage 1; PMP Projector Mounting Pole; Projector Bracket; PCM 240 Projector Ceiling Mount
• Page 15 – Mark screen location; When marking the location of screens, devices, or site; Install projector to verify location; PCM
• Page 16 – Installation — Stage One, cont’d; Adjust the threaded barrels at the end of each; Verify the image location; Remember to include the vertical and horizontal offsets
• Page 17 – Cut the ceiling tile; Place the tile on a box, mark hole center on the; Finish Projector Ceiling Mount; Take measurements with the PCM 240
• Page 18 – Secure the Projector Ceiling Mount; Attach turnbuckles at the corners; Tighten the turnbuckles
• Page 19 – Install any optional power outlets in the 2 gang opening; Install the Screen; Use S-hooks to hang the screen from the brackets.
• Page 20 – PoleVault Systems Installation • Installation — Stage 2; Stage Two — Install the Wall Plates and MLC 104 IP; Stage 2; This stage involves installing the devices shown below.; PVT CV D and PVT RGB D PoleVault A/V Source Input Wall Plates; Right Side; Rear View; MLC 104 IP Plus MediaLink Controller
• Page 21 – PVT transmitter installation; Cables
• Page 22 – Stage Two — Install the Wallplates and MLC 104 IP Plus; Repeat steps a to c for all the transmitters needing to be; Features for mud ring installation
• Page 23 – The optimum distance; Use the supplied labels for clear cable; Signal Cable; Pull the cables at each location.
• Page 24 – Installation — Stage Two, cont’d; Install wall plates
• Page 25 – Install MediaLink Controller; Connect the MLC power and RS-232 control cable as; Connecting the MLC to the switcher; From MLC 104 IP Plus; Wire stripping lengths
• Page 26 – Connect the IR/RS-232 projector communication cable as; Connect to the LAN using a CAT 5 cable
• Page 27 – Secure the MLC 104 IP Plus to the; Connections made to the MLC 104 IP Plus
• Page 28 – PoleVault Systems Installation • Installation — Stage 3; Stage Three — Install the PV SI 3C LP Ceiling Speakers; Stage 3; Receives and outputs audio signal from PVS 204SA switcher
• Page 29 – Install the speaker in the ceiling tile; Mark the tile and cut the hole
• Page 30 – Installation — Stage Three, cont’d; Use a handheld screwdriver, as a powered screwdriver; Secure speakers to structural ceiling; Turn and lock down the four dog legs
• Page 31 – mm) and secure the wires into the supplied
• Page 32 – Finish speaker installation; Install/replace the speaker grill on the front of the
• Page 33 – PoleVault Systems Installation • Installation — Stage 4; Stage 4; This stage covers installing the devices shown below.; PVS 204SA PoleVault Switcher; Stage Four — Install the PMK 450 and the PVS 204SA; VGA cable (connects to RGB output and projector)
• Page 34 – Installation — Stage Four, cont’d; The installation must conform to national and local; Install the PMK 450 Pole Mount kit; Gather the cables, pass them down; Switcher and projector cable overview
• Page 35 – Install the PVS 204SA switcher; Do not install the rubber feet on the switcher; Install the switcher and power supply
• Page 36 – Finish installing the Pole Mount kit; Do not thread the power cable through the
• Page 37 – Attach and screw down rear plate
• Page 38 – PoleVault Systems Installation • Installation — Stage 5; Stage 5; MLC 104 IP Plus User’s Manual; Configure the system; Download and install Extron’s Global Configurator; Stage Five — Configure the System; Launch the Global Configurator 2
• Page 39 – Select MLC 104 IP Plus/PoleVault System
• Page 40 – Installation — Stage Five, cont’d; Check that an image is present, adjust
• Page 41 – Set MLC volume to maximum, and adjust; Replace the front plate and; Final installation
• Page 42 – Optional Accessory Installation — PPC 25; Connect sensor to paging speaker; Open the sensor and; PPC 25 Installation Instructions
• Page 43 – Specifications; Mounting hardware; Specifications are subject to change without notice.; Installation — Reference Information; PoleVault Systems Installation • Reference Information
• Page 44 – Installation — Reference Information, cont’d; Devices; PVT CV D and PVT RGB D; Wall or furniture mountable with included Decora wall plate.; All nominal levels are at ± 10%