Page 2 - Precautions; 安全须知; 注意
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk o...
Page 3 - PoleVault Systems Installation • Introduction; Introduction; Overview; This manual covers the installation of the Extron PoleVault; in a drop ceiling room with a wood or concrete; The PoleVault System; FCC Class A Notice; the interference at his own expense.
1-1 PoleVault Systems Installation • Introduction Introduction Overview This manual covers the installation of the Extron PoleVault ™ System in a drop ceiling room with a wood or concrete structural ceiling. If the location has a concrete or beam style ceiling, alternative ceiling mounts can be obta...
Page 4 - Extron PoleVault; Extron Cables & Notes; PoleVault System installation and wiring overview
PoleVault Systems Installation • Introduction 1-2 Introduction, cont'd L R AU X/MIX IN DO NO T GR OU ND OR SHOR T SPEAKER OU TPUTS ! 1B 1A INPUTS OUTPUTS 2B 2A 3B 3A RS-232 MLC/IR DC VO L 4/8 Ohms AMPLIFIED OUTPUTS VO L/MUTE Tx A B C Rx IR 12V 10V PO WE R 12V 3A MA X US LIS TE D 1 7T T AU DIO /VI DE...
Page 5 - PoleVault Systems Installation • Introduction — Planning; Before you Begin Installation - Planning; that key aspects have been considered.; Typical classroom installation
1-3 PoleVault Systems Installation • Introduction — Planning Before you Begin Installation - Planning Before installation is started, several major factors must be considered to ensure that the overall installation is as smooth and trouble free as possible, and that the final finished project meets ...
Page 6 - Introduction — Planning, cont’d; Type and control (important for projector image viewing); Example classroom installation; b. Location of the screen and projector; Aligned with center of the screen. Not an obstruction to viewing; ADA overhead and side clearance requirements
PoleVault Systems Installation • Introduction — Planning 1-4 Introduction — Planning, cont’d • Lighting Type and control (important for projector image viewing) Ambient light from windows Student Desks Teacher’s Desk TV / VCR / DVDInputs Screen/White BoardLocation Windows MLC ControllerLocation ...
Page 7 - • Viewing obstructions; c. Location of MediaLink Controller and Wall Plates; • Forward and side reach (for full details refer to a copy of; Wall or floor cabled; d. Type and location of the speakers; Based on ceiling height and room size; Example classroom with four speaker installation
1-5 PoleVault Systems Installation • Introduction — Planning • Viewing obstructions Pillars, furniture etc., window locations for glare reduction, obstructions between projector and screen c. Location of MediaLink Controller and Wall Plates • Forward and side reach (for full details refer to a cop...
Page 8 - Introduction — Inventory Overview; PoleVault System Devices and Hardware; PMP; hardware, individually boxed and labeled.; PoleVault A/V Source Input Wall Plates, and are shipped as follows:
PoleVault Systems Installation • Introduction — Inventory Overview 1-6 Introduction — Inventory Overview UPB 25 White 60-773-03 UPB 25 Universal Projector Bracket PCM 240 Projector Ceiling Mount PCM 240 White 60-772-03 (4)Turnbuckles(5) Lag eyes screws(5) Concrete anchors(2) Cable clamps, Gal Steel(...
Page 9 - PoleVault System Devices and Hardware, cont’d
1-7 PoleVault Systems Installation • Introduction — Inventory Overview PVT CV D Wallplate PVT CV D White 60-819-13 (1) Mud ring (2) Dog legs(2) Dog leg screws (2) PVT mounting screws(1) Decora ® Faceplate (2) Faceplate screws *Part #’s 42-109-03 and 42-110-03contain 3 or 4 PoleVault Wallplates, acco...
Page 10 - PoleVault System Ceiling Speakers
Introduction — Inventory Overview, cont’d 1-8 PoleVault Systems Installation • Introduction — Inventory Overview 1-8 N If any items in the PoleVault System boxes are damaged or missing, contact the Extron Technical Hotline (see rear cover for contact numbers). PV SI 3C LP Speakers PV SI 3C LP White ...
Page 11 - b. Items not included
1-9 PoleVault Systems Installation • Introduction — Inventory Overview 1-9 b. Items not included The following items are not included. However, input and display devices are essential parts of the system, and at any installation they may vary depending on their use. This list suggests various device...
Page 12 - d. Installation tools; Tools should include, but are not confined to:
PoleVault Systems Installation • Introduction — Inventory Overview 1-10 Introduction — Inventory Overview, cont’d d. Installation tools To aid the professional installer, this checklist gives the tools recommended to complete the installation. Tools should include, but are not confined to: • Laser l...
Page 13 - PoleVault Systems Installation • Installation Overview; Installation Overview; in five sections, Stages One though Five.; Outline of installation steps; — Install the PV SI 3C LP Ceiling Speakers.
2-1 PoleVault Systems Installation • Installation Overview Installation Overview Installation Overview This overview outlines the basic steps for installing the PoleVault System. Detailed description of these steps is given in five sections, Stages One though Five. N Additional installation hardware...
Page 14 - PoleVault Systems Installation • Installation — Stage 1; Stage One — Install the Screen and Projector; Stage 1; PMP Projector Mounting Pole; Projector Bracket; PCM 240 Projector Ceiling Mount
PoleVault Systems Installation • Installation — Stage 1 2-2 Stage One — Install the Screen and Projector Stage 1 This stage involves installing the three pieces of hardware shown below. Cable AccessCutout(install thisend uppermost) Threaded at bothends PMP Projector Mounting Pole T-barSecuring Screw...
Page 15 - Mark screen location; When marking the location of screens, devices, or site; Install projector to verify location; PCM
2-3 PoleVault Systems Installation • Installation — Stage 1 1. Mark screen location a. Mark the center line and the outer edges of screen. T When marking the location of screens, devices, or site for installing transmitters and MediaLink control devices, use painters’ tape to avoid wall surface dama...
Page 16 - Installation — Stage One, cont’d; Adjust the threaded barrels at the end of each; Verify the image location; Remember to include the vertical and horizontal offsets
PoleVault Systems Installation • Installation — Stage 1 2-4 Installation — Stage One, cont’d e. Using suitable screws, mount the projector onto the lower portion of the UPB 25 (the projector bracket, see b in step 2d’s drawing). Align it so the security flange is at the rear. A minimum of three arms...
Page 17 - Cut the ceiling tile; Place the tile on a box, mark hole center on the; Finish Projector Ceiling Mount; Take measurements with the PCM 240
2-5 PoleVault Systems Installation • Installation — Stage 1 4. Cut the ceiling tile a. Mark the location of the PCM 240 on the T-bar, before removing it. This aids putting it back in the correct location when the tile is replaced. T Mark the screen direction on back of the tile (e.g. with an arrow o...
Page 18 - Secure the Projector Ceiling Mount; Attach turnbuckles at the corners; Tighten the turnbuckles
PoleVault Systems Installation • Installation — Stage 1 2-6 Installation — Stage One, cont’d 6. Secure the Projector Ceiling Mount to the ceiling a. Attach the four turnbuckles to the mounting plate, one at each corner. C DO NOT rest or lean on the mounting plate or suspended ceiling when attaching ...
Page 19 - Install any optional power outlets in the 2 gang opening; Install the Screen; Use S-hooks to hang the screen from the brackets.
2-7 PoleVault Systems Installation • Installation — Stage 1 T Install any optional power outlets in the 2 gang opening on the mounting plate, towards the outside edge of the mount, so it does not interfere with the PMK 450 when installed. C For safety, all wiring of the electrical boxes and accessor...
Page 20 - PoleVault Systems Installation • Installation — Stage 2; Stage Two — Install the Wall Plates and MLC 104 IP; Stage 2; This stage involves installing the devices shown below.; PVT CV D and PVT RGB D PoleVault A/V Source Input Wall Plates; Right Side; Rear View; MLC 104 IP Plus MediaLink Controller
PoleVault Systems Installation • Installation — Stage 2 2-8 Stage Two — Install the Wall Plates and MLC 104 IP Stage 2 This stage involves installing the devices shown below. AUDIO IN L R VIDEO IN Audio andVideo input connectors Audio and Videooutput port (at rear) PVT CV D AUDIO IN L R VIDEO IN Mou...
Page 21 - PVT transmitter installation; Cables
2-9 PoleVault Systems Installation • Installation — Stage 2 PVT transmitter installation • CAT 5 T568A signal transmission cables (connects PVT’s to PVS 204SA switcher) MLC 104 IP Plus installation • MLC power and RS-232 control cable (connects the MLC to the MLC/Power control port on the PVS 204SA ...
Page 22 - Stage Two — Install the Wallplates and MLC 104 IP Plus; Repeat steps a to c for all the transmitters needing to be; Features for mud ring installation
PoleVault Systems Installation • Installation — Stage 2 2-10 Stage Two — Install the Wallplates and MLC 104 IP Plus N The installation must conform to national and local electrical codes, and UL requirements. Refer to the devices’ user manuals for details. 1. Install mud rings N These devices can be...
Page 23 - The optimum distance; Use the supplied labels for clear cable; Signal Cable; Pull the cables at each location.
2-11 PoleVault Systems Installation • Installation — Stage 2 2. Pull cables The following cables need to be installed: • CAT 5 cables for signal transmission from the A/V Wall plates to the PVS 204SA. N For PVT RGB D Wall plates, two CAT 5 signal cables for each input are needed. Maximum distance fr...
Page 24 - Installation — Stage Two, cont’d; Install wall plates
PoleVault Systems Installation • Installation — Stage 2 2-12 Installation — Stage Two, cont’d 3. Install wall plates a. Connect the CAT 5 cables to the rear of the input devices (for RGB devices, cable labeled A to port A, cable B to port B). b. Mount each device into the mud ring. c. Attach the sup...
Page 25 - Install MediaLink Controller; Connect the MLC power and RS-232 control cable as; Connecting the MLC to the switcher; From MLC 104 IP Plus; Wire stripping lengths
2-13 PoleVault Systems Installation • Installation — Stage 2 4. Install MediaLink Controller T Before cabling and installing the MLC 104 IP Plus, locate and write down the MAC address of the device for configuring the IP address. The 12 character alphanumeric address (e.g., 00-05-A6-03-9G-H4) can be...
Page 26 - Connect the IR/RS-232 projector communication cable as; Connect to the LAN using a CAT 5 cable
PoleVault Systems Installation • Installation — Stage 2 2-14 Installation — Stage Two, cont’d b. Connect the IR/RS-232 projector communication cable as shown for either RS-232 or IR projector control. c. Connect a CAT 5, 5e, or 6 straight through cable to the MLC ‘s RJ-45 jack. W DO NOT connect the ...
Page 27 - Secure the MLC 104 IP Plus to the; Connections made to the MLC 104 IP Plus
2-15 PoleVault Systems Installation • Installation — Stage 2 ExtronMLC 104 IP Plus Rotate locking armand insert into wallopening. OFF ON OFF ON Ext ron CONFI G DIS PLA Y MLC 104 IP P lus VOLUME 1 2 3 4 ON OF F VC R DV D PC ExtronMR 200 Modular Mud Ring 4e Secure the MLC 104 IP Plus to the mud ring T...
Page 28 - PoleVault Systems Installation • Installation — Stage 3; Stage Three — Install the PV SI 3C LP Ceiling Speakers; Stage 3; Receives and outputs audio signal from PVS 204SA switcher
PoleVault Systems Installation • Installation — Stage 3 2-16 Stage Three — Install the PV SI 3C LP Ceiling Speakers Stage 3 This stage involves installing the devices shown below. Where it goes: Installs in ceiling tiles at predetermined location for best acoustics. Connects to switcher. What it doe...
Page 29 - Install the speaker in the ceiling tile; Mark the tile and cut the hole
2-17 PoleVault Systems Installation • Installation — Stage 3 N The installation must conform to national and local electrical codes, and UL requirements. Refer to the device’s user manual for details. 1. Cut ceiling tile If installing PV SI 3C LP speakers, do the following:a. Remove the ceiling tile...
Page 30 - Installation — Stage Three, cont’d; Use a handheld screwdriver, as a powered screwdriver; Secure speakers to structural ceiling; Turn and lock down the four dog legs
PoleVault Systems Installation • Installation — Stage 3 2-18 Installation — Stage Three, cont’d e. Loosen the four screws on the front baffle (counter clockwise) 1/2 turn (see figure, A) and turn the doglegs to lock onto the C-ring. Tighten down the front screws (see figure, B). T Use a handheld scr...
Page 31 - mm) and secure the wires into the supplied
2-19 PoleVault Systems Installation • Installation — Stage 3 c. To terminate the cable, strip the end of the cable 0.2" (5 mm) and secure the wires into the supplied 4-pole captive screw connector. d. Plug the 4-pole connector into the speaker terminal and replace and secure the plenum cover N T...
Page 32 - Finish speaker installation; Install/replace the speaker grill on the front of the
PoleVault Systems Installation • Installation — Stage 3 2-20 Installation — Stage Three, cont’d 5. Finish speaker installation a. Install/replace the speaker grill on the front of the speaker, using the supplied adhesive tabs (putty) to secure it in place. b. Repeat cabling and final installation st...
Page 33 - PoleVault Systems Installation • Installation — Stage 4; Stage 4; This stage covers installing the devices shown below.; PVS 204SA PoleVault Switcher; Stage Four — Install the PMK 450 and the PVS 204SA; VGA cable (connects to RGB output and projector)
2-21 PoleVault Systems Installation • Installation — Stage 4 Stage 4 This stage covers installing the devices shown below. L R AUX/MIX IN 1B 1A I NPUTS OU TPUTS 2B 2A 4 3 RS-232 MLC/IR DC VOL 4/8 Ohms AMPLIFIED OUTPUTS VOL/MUTE Tx A B C Rx IR 12V 10V POWER 12V 3A MAX US LISTED 17TT AUDIO/VIDEO APPAR...
Page 34 - Installation — Stage Four, cont’d; The installation must conform to national and local; Install the PMK 450 Pole Mount kit; Gather the cables, pass them down; Switcher and projector cable overview
PoleVault Systems Installation • Installation — Stage 4 2-22 Installation — Stage Four, cont’d N The installation must conform to national and local electrical codes, and UL requirements. Refer to the device’s user manual for details. 1. Pull the cables a. Loosen the PCM 240 set screws and remove th...
Page 35 - Install the PVS 204SA switcher; Do not install the rubber feet on the switcher; Install the switcher and power supply
2-23 PoleVault Systems Installation • Installation — Stage 4 3. Install the PVS 204SA switcher a. Pass two 4-40 x 3/16" screws up through the PMK’s bottom plate into the holes in the base of the switcher, and secure it in place at the left front of the bottom plate. N Do not install the rubber f...
Page 36 - Finish installing the Pole Mount kit; Do not thread the power cable through the
PoleVault Systems Installation • Installation — Stage 4 2-24 Installation — Stage Four, cont’d L R AUX/MIX IN 1B 1A I NPUTS OU TPUTS 2B 2A 4 3 RS-232 MLC/IR DC VOL 4/8 Ohms AMPLIFIED OUTPUTS VOL/MUTE Tx A B C Rx IR 12V 10V POWER 12V 3A MAX US LISTED 17TT AUDIO/VIDEO APPARATUS ® RGB VIDEO RGB VIDEO S...
Page 37 - Attach and screw down rear plate
2-25 PoleVault Systems Installation • Installation — Stage 4 FRONT REAR Rear Plate 4c Attach and screw down rear plate 4d Replace projector on the adjuster plate b. Align the bottom plate lugs with the slots in the top plate and slide up and into place. c. Attach the rear plate to secure the PMK 450...
Page 38 - PoleVault Systems Installation • Installation — Stage 5; Stage 5; MLC 104 IP Plus User’s Manual; Configure the system; Download and install Extron’s Global Configurator; Stage Five — Configure the System; Launch the Global Configurator 2
PoleVault Systems Installation • Installation — Stage 5 2-26 Stage Five — Configure the System Stage 5 Items needed to help complete this stage:• Laptop (or PC) with a network connection • GC 2 configuration program (download from www.extron.com) • MLC 104 IP Plus User’s Manual • Projector manufactu...
Page 39 - Select MLC 104 IP Plus/PoleVault System
2-27 PoleVault Systems Installation • Installation — Stage 5 1d Select MLC 104 IP Plus/PoleVault System from the drop down box d. Select the MLC 104 IP Plus/PoleVault system from the drop-down box. Follow the instructions on the help page. e. To move to the next page (shown in the yellow box), click...
Page 40 - Installation — Stage Five, cont’d; Check that an image is present, adjust
PoleVault Systems Installation • Installation — Stage 5 2-28 Installation — Stage Five, cont’d 2c Check that an image is present, adjust as needed. 2. Test the system a. Ensure power is supplied to the PVS 204SA switcher, and power on the MLC 104 IP Plus. b. Connect all the input devices (e.g., PC, ...
Page 41 - Set MLC volume to maximum, and adjust; Replace the front plate and; Final installation
2-29 PoleVault Systems Installation • Installation — Stage 5 2e Set MLC volume to maximum, and adjust the level on the switcher FRONT REAR FrontPlate Cable frompower source Tighten Front andRear Plate Screws (4)and Side Screws (2) 3a Replace the front plate and 3b tighten down the screws on the moun...
Page 42 - Optional Accessory Installation — PPC 25; Connect sensor to paging speaker; Open the sensor and; PPC 25 Installation Instructions
PoleVault Systems Installation • Optional Accessory Installation 2-30 Optional Accessory Installation — PPC 25 1. Connect sensor to paging speaker a. Open the top of the Priority Page Sensor. b. Loop (only) one of the Paging speaker wire leads around the top (open) part of the Sensor. Either speaker...
Page 43 - Specifications; Mounting hardware; Specifications are subject to change without notice.; Installation — Reference Information; PoleVault Systems Installation • Reference Information
Specifications For detailed specifications and warranty information of the PoleVault System components, refer to the device manuals, or the product pages at www.extron.com. Mounting hardware PCM 240 Mounting ........................................ Drop ceiling mountEnclosure type .....................
Page 44 - Installation — Reference Information, cont’d; Devices; PVT CV D and PVT RGB D; Wall or furniture mountable with included Decora wall plate.; All nominal levels are at ± 10%
PoleVault Systems Installation • Reference Information 2-32 Installation — Reference Information, cont’d Devices PVS 204SA External power supply ................. 100 VAC to 240 VAC, 50/60 Hz, external, autoswitchable; to 12 VDC, 3 A, regulatedPower input requirements ........... 12 VDC, 0.97 A (typ...
Extron 60-442-01
Manual
Extron 88
Manual
Extron DVS 304 D
Manual
Extron M59-6 BNC
Manual
Extron GLI 1000 HD
Manual
Extron SI 26
Manual
Extron VSC 700
Manual
Extron MHR-5P BNC/50
Manual
Extron SW8/12 VGA
Manual
Extron MAV 84
Manual
Extron MDA 5SVA RCA
Manual
Extron RS-232
Manual
Extron MLS 506SA
Manual
Extron MLS 406
Manual
Extron IN1608
Manual
Extron BNC 5 RC
Manual
Extron TPR150
Manual
Extron MPX Plus 866 A
Manual
Extron CCR 204
Manual
Extron WPC 210 A MK
Manual