Extron MLC 206 - Manual
Extron MLC 206 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – MLC 206 Setup Guide, cont’d; Step 1 — Computer Connection; and for loading configuration and driver files into the MLC.; Connect all control modules that will be used in the system.; A B C D; MLC 206 to a control module; Total distance from
- Page 3 – To power the MLC, connect a 12 VDC power supply or an optional; MediaLink Switcher; MLC 206 powered by a MediaLink Switcher; A B; A ground wire must be connected; A B; Step 2 — Software Installation; that appear on the screen.
- Page 4 – Step 3 — Setting up projector control; It is strongly recommended that an RS-232 control (; Load Extron Driver; filename
- Page 5 – Projector; Step 4 — IR learning; If a button has been previously configured, it will have a red (IR) or
- Page 6 – OK; MIN; Learn IR to Button
- Page 7 – Step 5 — Completing the installation; . Save the configuration by selecting; Relays
- Page 8 – IR; Connect up to a maximum; User Mode; MLC 206 User’s Manual; Color; To the; © 2009 Extron Electronics. All rights reserved.
The Extron MediaLink
™
Controller (MLC 206) provides infrared (IR) and RS‑232
remote control of a display device, contact closure control of items in a room, tally
outputs, and MediaLink Switcher control.
This guide provides instructions for an experienced installer to set up and operate
the MLC 206 MediaLink Controller.
When possible in the following pages, line drawings are used to clarify steps
discussed in the text.
Setup Guide — MLC 206
68-601-50
Rev. A
11 09
MLC 206 typical application diagram
VCR
Extron
Switcher
DVD
Laptop
Extron MLC 206
Lighting
Control
Switcher
Control
Screen
Control
Projector
Control
100
-24
0V
0.2
A 5
0/6
0 H
z
AU
DIO
OU
T
INP
UT
1
VID
EO
R-Y
L
R
YU
V
Y
R-Y
B-Y
VID
EO
S-V
IDE
O
Y
C
INP
UT
2
VID
EO
Y
R-Y
L
R
INP
UT
3
Y
B-Y
L
R
INP
UT
4
L
R
INP
UT
5
B
L
R
RG
B
R
H/
HV
G
V
B
L
R
AU
X/M
IX
L
R
EF
FE
CT
S
L
R
SE
ND
L
R
RE
TU
RN
CO
MM
LIN
K
A B
C D
E
RS
232
CO
NTA
CT
CL
OS
UR
E
4 o
hm
MO
NO
AM
PL
IFIE
D O
UT
PU
T
CO
MM
8 o
hm
70V
Document
Camera
Ext
ron
ML
C 2
06
DIS
PL
AY
PO
WE
R
VO
LU
ME
MA
X/
MIN
VC
R
DV
D
Lap
top
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
MLC 206 Setup Guide, cont’d 2 Step 1 — Computer Connection The MLC 206 must be connected to a PC in order to configure the controller. The configuration port, shown in the rear panel view below, is used for system control and for loading configuration and driver files into the MLC. 1. Connect a host...
3 3. To power the MLC, connect a 12 VDC power supply or an optional MediaLink Switcher (MLS) to the MLS/Power port, and connect the power supply or the switcher to a power source. MediaLink Switcher MLC/RS-232 A B MLC 206 powered by a MediaLink Switcher Connecting an MLC 206 to an external power sup...
MLC 206 Setup Guide, cont’d 4 Step 3 — Setting up projector control Device drivers allow the MLC 206 to control projectors and other source devices via RS‑232 or IR. N It is strongly recommended that an RS-232 control ( filename RS1.mll) file for controlling a projector be used whenever possible. To...
