Extron MKP 2000 - Manual

Table of Contents:

• Page 2 – Precautions; Safety Instructions • English; Extron’s Warranty
• Page 3 – MKP 2000 Remote Control Panel • Quick Start Guide; Quick Start Guide — MKP 2000
• Page 4 – Quick Start Guide — MKP 2000, cont’d; MKP 2000 Remote Control Panel• Table of Contents; Chapter 1 • Introduction; Chapter 3 • Local Operation; Table of Contents; Program the control panel with the size of the connected switcher; See System Settings Page in chapter 5, HTML Operation.; Use the control panel to select inputs and outputs; Operations in chapter 3, Local Operation.
• Page 5 – Table of Contents, cont’d; MKP 2000 Remote Control Panel; Chapter One; Introduction; About the MKP 2000 Remote Control Panel; Chapter 5 • HTML Operation
• Page 6 – Figure 1-1 — Typical MKP 2000 applications; RS-232 connection to the switcher
• Page 7 – Chapter Two; Installation; MKP Installation Overview
• Page 8 – UL Requirements for Wall Box Installation; Figure 2-1 — MKP mounted in a wall box; Installation Procedures; CAUTION; To install an MKP 2000 remote control panel, follow these steps:
• Page 9 – Install the mud ring or wall box as follows:; If you are using a mud ring; , use the template that came; Cut out the wall/furniture material from the marked area.; If you are using a wall box; , feed cables through the wall
• Page 10 – Figure 2-3 — Attaching a mud ring to a wall; , insert the wall box into the; Figure 2-4 — Attaching a wall box to a wall stud; Mounting the MKP to the mud ring or wall box
• Page 11 – Figure 2-5 — Mounting the MKP to the wall box; Rear Panel and Side Panel Connections; Figure 2-6 — MKP rear and side panels; Ethernet connection indicators; If desired, connect a host computer or; Switcher RS-232 port —; If desired, connect a cable between this; Power connector —; Plug the included external 12 VDC power
• Page 12 – Control connections; Figure 2-8 — MKP connection using the RS-232 port; Cut off the foil shield and discard it.
• Page 13 – TP cable termination; Crossover cable —; Direct connection between the MKP; Figure 2-11 — RJ-45 connector and pinout tables
• Page 14 – MKP 2000 Remote Control Panel • Installation; Chapter Three; Local Operation; Front Panel Controls and Indications; Power supply wiring; Figure 2-12 shows how to wire the connector.; Figure 2-12 — Power connector wiring
• Page 15 – Figure 3-1 — MKP 2000 controls and indicators; Front Panel Operations; Creating a tie
• Page 16 – Local Operation, cont’d; Viewing the last input or output tied from the MKP; Press either the Input button or the Output button.
• Page 17 – OP; Figure 3-2 — Selecting octet fields and host control; Host control port setting and pass-through communications; Selected as secondary,
• Page 18 – Control panel security lockout (executive mode); LOC; Figure 3-3 — Control panel lockout; Rear Panel Resets; Performing soft resets; Figure 3-4 — Soft resets
• Page 19 – MKP 2000 Remote Control Panel • Local Operation; Chapter Four; SIS Operation; Ethernet Link; Performing a hard reset; erases all user-installed software or firmware. Perform a; Power; Figure 3-5 — Hard reset
• Page 20 – The default protocol for both ports is as follows:; Figure 4-1 — RS-232 connector pin assignments; Routing matrix switcher commands; Default IP address
• Page 21 – SIS Operation, cont’d; Login Administrator; MKP Error Responses
• Page 22 – Symbol definitions for MKP SIS commands; = n=–1= redirect serial port data from the specified port to allow for; = Daylight Savings Time
• Page 23 – esponse table for MKP SIS commands (continued)
• Page 25 – MKP 2000 Remote Control Panel • SIS Operation; Chapter Five; HTML Operation
• Page 26 – Figure 5-1 — Enter Network Password page; If neither of the above conditions is true; Download the Startup Page
• Page 27 – HTML Operation, cont’d; Figure 5-2 — System Status page; System Settings Page; Figure 5-3 — System Settings page
• Page 28 – IP Settings section; Click the appropriate radio button to select among:; Pass Through selected —; Commands received on the
• Page 29 – Authorized inputs and authorized outputs; Date/Time Settings fields; Figure 5-4 — Port Settings page
• Page 30 – Figure 5-5 — Passwords page; Firmware Upgrade Page; Figure 5-6 — Firmware Upgrade page
• Page 31 – Figure 5-7 — Firmware upgrade open file window; File Management Page; Figure 5-8 — File Management page
• Page 32 – MKP 2000 Remote Control Panel • HTML Operation; Special Characters; Cannot include spaces or underscore characters; Appendix A; Reference Data; Specifications
• Page 33 – Control/remote — keypad; connectors; General; wall box; Specifications are subject to change without notice.; Part Numbers; Included parts; These items are included in each order for an MKP 2000:; Installation accessories; Cables
• Page 34 – Reference Data, cont’d; Electrical box cutout; Drawn to scale may be used as a template.; VOLUME; Full Size; t area sho
• Page 35 – MKP 2000 Remote Control Panel • Reference Data; Extron Comm-Link cable