Extron IPL T S6 - Manual

Extron IPL T S6

Extron IPL T S6 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
Page: / 45

Table of Contents:

  • Page 2 – Precautions; Safety Instructions • English
  • Page 3 – 注意; FCC Class A Notice
  • Page 5 – IPL T S Series Interfaces • Table of Contents; Table of Contents; Chapter One • Introduction
  • Page 6 – Table of Contents, cont’d; Launching the GlobalViewer Interface
  • Page 7 – IPL T S Series Interfaces; Chapter One; Introduction; About this Manual
  • Page 8 – IPL T S Series Interfaces • Introduction; The Extron IPL T S Series interface boxes can be installed as; Typical IPL T S Series Interface application
  • Page 9 – IPL T S1
  • Page 10 – Global Configurator; Global Configurator application screen
  • Page 11 – Use Global Configurator version 2.2 or later.; System requirements; If ActiveX is not enabled, you may get a prompt from the; Installing Global Configurator
  • Page 12 – Software
  • Page 13 – Chapter Two; Hardware Setup; Front Panel
  • Page 14 – IPL T S Series Interfaces • Hardware Setup
  • Page 15 – Rear Panel
  • Page 16 – Hardware Setup, cont’d; crossover
  • Page 17 – Pinouts for the two types of Ethernet cables are shown below:; Serial Device Connection; Straight-through Cable
  • Page 18 – Pin; Captive screw connector
  • Page 21 – Chapter Three; Software Setup; Creating a Global Configurator Project File
  • Page 22 – IPL T S Series Interfaces • Software Setup; Step one: download device drivers; or; GC
  • Page 23 – Download
  • Page 24 – Software Setup, cont’d; Step two: create a new project; To create a new Global Configurator project file:; Create a New Project; Click; OK
  • Page 25 – Enter the IP address of the first device you will add to your
  • Page 26 – Step three: add a device; Add Device
  • Page 27 – Auto Configure IP Address
  • Page 28 – Step four: define the location of the new device; New Location
  • Page 29 – Step five: save the new Global Configurator file; Save
  • Page 30 – Step six: configure contacts; The Contact Manager dialog box is used to enter the name,; Add
  • Page 31 – The Email Manager dialog box is used to create custom e-mails
  • Page 32 – Step eight: assign device drivers; Driver Configuration
  • Page 33 – Step nine: set scheduled actions and e-mail; Schedule
  • Page 34 – Enter a unique schedule name.; Next; Actions; Apply Action
  • Page 36 – Contact Manager
  • Page 37 – Step ten: set monitored conditions; Monitor
  • Page 39 – Building and Uploading a GC File; Step eleven: build the Global Configurator file; • Build All Configurations
  • Page 40 – Step twelve: upload the Global Configurator file; Click the; Begin; When the upload process completes, the Progress and Status; Test GV System; button to view the GlobalViewer
  • Page 41 – If for any reason you need to change any of the previously; Tools > Change Device Settings; Settings; to open the Settings drop-down listing.; Set; in the drop-down listing to
  • Page 42 – Step fourteen: launch GlobalViewer
  • Page 44 – Extron’s Warranty
  • Page 45 – Chapter 1; Setup Guide Checklist
Loading the manual

Setup Guide

68-1377-01

Rev. C

11 08

IPL T S Series

Interfaces

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Precautions; Safety Instructions • English

Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may pres...

Page 3 - 注意; FCC Class A Notice

安全须知 • 中文 这个符号提示用户该设备用户手册中有重要的操作和维护说明。 这个符号警告用户该设备机壳内有暴 露的危险电压，有触电危险。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解 所 有 安 全 和 使 用 说 明 。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 避免追加 • 不要使用该产品厂商没有推荐的工具或 追加设备，以避免危险。 警告 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必 须 使 用 有 地 线 的 供 电 系 统 供 电 ...

Page 5 - IPL T S Series Interfaces • Table of Contents; Table of Contents; Chapter One • Introduction

i IPL T S Series Interfaces • Table of Contents Table of Contents Chapter One • Introduction ................................................... 1-1 About this Manual .................................................................... 1-2 IPL T S Series Products .......................................

Other Extron Models

All Extron Other