Extron 68-1021-01 - Manual

Table of Contents:

• Page 2 – Precautions; Safety Instructions • English; FCC Class A Notice; Extron’s Warranty
• Page 3 – IPL M PDP-ES • Quick Start Guide; Turn all of the equipment off; and disconnect it from the power; Remove the preinstalled Pioneer communication ES card; from the; Install the Extron IPL M PDP-ES interface card; into the Pioneer; Quick Start Guide — IPL M PDP-ES
• Page 4 – Chapter 1 • Introduction; Chapter 4 • Communication and Control; Table of Contents; Attach the serial communication cable; to the RS-232 port of the; Configure the IPL M PDP-ES interface; via the default Web; The IPL M PDP-ES interface card
• Page 5 – Table of Contents, cont’d; Chapter One; Introduction; About this Manual; Pioneer Plasma A/V Device Control; Appendix A • Specifications; Specifications; Appendix B • Glossary
• Page 6 – IPL M PDP-ES • Introduction
• Page 7 – Chapter Two; Installation and Operation; Installation Overview
• Page 8 – CAUTION; Installing the Extron IPL M PDP-ES card; Install the Extron IPL M PDP-ES interface card.; Installation of the IPL M PDP-ES Interface Card; Removing the Pioneer communication ES card; Figure 2-1— Pioneer ES Card Slots; Gently pull the center knob
• Page 9 – Installation and Operation, cont’d; Ethernet/LAN communication; LAN Activity LED; For best performance, use a shielded Ethernet cable.; Power; — The green LED lights to indicate; Figure 2-5 — The IPL M PDP-ES sticker label; Push gently
• Page 10 – Resetting the unit; A mode 2 reset disconnects a pass-through connection.; Pin; Operation; DB9 Pin Location
• Page 11 – IPL M PDP-ES • Installation and Operation; Chapter Three; Connection and Configuration; Connecting the Hardware; Mode 4
• Page 12 – PC connection; Connect the other end of the cable to a local PC.; Serial connection; Figure 3-2 — Controller device wiring; Configuring the Hardware; PC configuration; Figure 3-1 — IPL M PDP-ES interface connections; Direct PC connection
• Page 13 – Connection and Configuration, cont’d; Figure 3-3 — Executing the ARP command; IPL M PDP-ES interface card configuration; Use the ARP command method.; Configuring the IPL M PDP-ES using the ARP command; Use ARP to configure the IP address as follows:
• Page 14 – Configuring the IPL M PDP-ES using the RS-232 port; The unit should respond with; table; arp –d; removes all static IP addresses from the ARP table.; Configuring the IPL M PDP-ES using direct PC connection
• Page 15 – IPL M PDP-ES • Connection and Configuration; Chapter Four; Communication and Control; Communication with the Interface Card; Firmware upgrades
• Page 16 – Accessing and using the Web server; Launch your Web browser.; Navigating the default Web pages; Status tab; Figure 4-1 — System Status page; Configuration tab; Figure 4-2 — System Settings page
• Page 17 – IPL M PDP-ES • Communication and Control; Gateway IP address; To do so; IP settings fields; Click in the address field.
• Page 18 – Communication and Control, cont’d; Figure 4-4 — Web server Passwords screen; Email Alerts page; Tab over to the second field to reenter the same password.
• Page 19 – To edit notification email addresses from the Email Alerts page:; File names must end with an .eml extension.; Sending an email alert through Telnet; Figure 4-7 — Firmware Upgrade page
• Page 20 – File Management tab; Figure 4-8 — Web server File Management screen; To create a directory:
• Page 21 – Pioneer tab; have no access to this tab.; Display Status page; Figure 4-9 — Pioneer Display Status screen; Display Controls page; Figure 4-10 — Pioneer Display Controls screen; • A blue button indicates normal input.; These buttons power the Pioneer plasma on or off.; Input
• Page 22 – Advanced Controls page; Figure 4-11 — Pioneer Advanced Control screen
• Page 23 – Energy Save; Figure 4-12 — Pioneer Schedule screen; Monitor page; Figure 4-14— Pioneer Monitor screen
• Page 24 – Symbol definitions; = Command data section; Using the command/response table; Note for Web browsers
• Page 25 – Applicable to Ethernet only.; Copyright information; Email files must have the file extension .eml.
• Page 26 – Commands that give E14 (Invalid Command for this; administrator level; able for Simple Instruction Set (SIS) commands; Command; Bidirectional Serial Data port
• Page 27 – IP Setup Commands; Password and Security Settings
• Page 29 – Ether; Custom Web pages; Accessing and using Telnet; Figure 4-18 — Telnet command prompt
• Page 30 – Figure 4-19 — Connecting to the IP address; Using direct access; Send Pioneer commands directly to the Pioneer plasma.; Port redirect; Troubleshooting; Power connections; Ensure that the Pioneer plasma is plugged in.; Data connections
• Page 31 – Appendix A; and Accessories; Serial connections; Check to see that events are running.; If status is missing or unavailable; Ensure that the redirect port has been enabled.; If you are unable to access the Web server; If you are still experiencing problems, call the Extron S
• Page 32 – Specifications, Part Numbers, and Accessories; Parts; Included parts; Included parts Replacement part number; IPL M PDP-ES User ’s Manual; Ethernet control interface; autodetect; Serial control interface
• Page 33 – IPL T S Series • Specifications, Part Numbers, and Accessories; Appendix B; Glossary
• Page 34 – GLOSSARY
• Page 35 – Port number; is a preassigned address within a server that; Static IP; refers to an IP address that has been specifically; Telnet; is a utility available on most PCs that allows the; URL encoding; allows you to send information and commands
• Page 36 – IPL M PDP-ES • Glossary