Everpure CGHE1 - Manual
Everpure CGHE1 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – IMPORTANT SAFETY INSTRUCTIONS; PLEASE READ ALL INSTRUCTIONS VERY CAREFULLY; ELECTRICAL REQUIREMENTS; Recommended Ground Method; SAVE THESE INSTRUCTIONS. THIS PRODUCT FOR HOUSEHOLD USE ONLY.; WARNING; Do not use an adapter.
- Page 3 – Observe all governing codes and ordinances.; OFF; OVERVIEW
- Page 4 – Before You Begin; FAUCET MUST BE “OPEN VENT” STYLE.; INSTALLATION
- Page 5 – “T” connection with; TYPICAL INSTALLATIONS; Step 4 - Connect Cold Water Supply; Check Filter in Quick-Connect Fitting
- Page 6 – Step 7 - Test Installation; LOW
- Page 7 – CLEANING AND MAINTENANCE; Seasonal Shutdown; Cleaning Quick-Connect Filter Screen at Cold Water Inlet; Quick-connect with filter and cap
- Page 8 – TROUBLESHOOTING
CGHE1 Installation
& Operating Guide
Faucet Compatibility
Tools and Safety Equipment you may need (not provided)
Only “Open Vent” faucets function with a instant hot water dispenser tank.
Connecting a standard faucet will damage the tank and void the warranty.
2 mounting bracket screws
(and 2 plastic anchors if
attaching to drywall)
1
/
4
" (6.4 mm)
O.D. copper
tubing.
Materials required (not provided)
Components
tank mounting
bracket
tank
When you purchase the Everpure
®
Commerical
Grade Instant Hot Water tank, contents include:
quick-connect
fitting
Shut-Off valve
with “T” fitting
(EV312120)
• ruler or measuring tape
• pliers
• hand or electric drill
• small drill bit for starter holes
• 1
3
/
8
" drill bit - if no sink
hole exists
• safety glasses
• bucket or pan
• open-end wrench(es)
• gloves
• tubing cutter
EVERPURE INST
ANT HOT W
A
TER DISPENSER
(Connections must meet all local codes and ordinances.)
This hot water dispenser produces instant hot water of approximately 190°F (88°C) as dispensed
from the faucet.
This product is not intended to produce a continuous flow of hot water. The standard model will
produce up to 60 cups of water per hour at approximately 190°F (88°C). Due to high water
temperature, for safety reasons, the tank is not under pressure. Consequently, there is a slight
delay of water flow after the faucet has been activated. This is normal and indicates that the
expansion chamber is functioning properly.
IMPORTANT INFORMATION
560H486P01 REV E
quick-connect fitting
with filter and cap
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
IMPORTANT SAFETY INSTRUCTIONS PLEASE READ ALL INSTRUCTIONS VERY CAREFULLY When using electrical appliances, basic safety precautions should always be followed including the following: ELECTRICAL REQUIREMENTS Recommended Ground Method 1. Read all instructions. 2. To protect against electrical shock, ...
Faucet may be installed in spray hose opening in sink or drilledhole. If faucet is not to be installed in sink spray hose opening,cut 1 1 / 16 ” (27mm) min. — 1 3 / 8 ” (35mm) max. dia. hole. Important: Observe all governing codes and ordinances. 6 13 / 16 ” (173 mm) 11 1 / 8 ” (283 mm) 8 1 / 16 ” (...
Step 1 - Mounting Tank Position tank vertically beneath faucet so the flexibletube from the faucet reaches the center faucet supplytube on the tank and tank touches the wall. Mark thewall at the top of tank. Set tank aside. Mark a secondline 2 1 / 8 ” (54 mm) below the first line. Align bottom of br...
