Page 2 - Operation Instruction
2 E V E R F O C U S E L E C T R O N I C S C O R P O R A T I O N P/N: 4605XZ0650001AR Operation Instruction 2008 EverFocus Electronics Corp Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was c...
Page 3 - Precautions; Do not place any object on top of the cover.
3 Precautions 1. Do not place any object on top of the cover. 2. Be careful when handling the camera, do not drop it or subject it to strong shock or vibration to prevent any damages to it. Do not disassemble it or place it on an unstable base. 3. Install the camera away from TV, radio transmitter, ...
Page 4 - Federal Communication Commission Interference Statement; or
4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential in...
Page 5 - Table of Contents
5 Table of Contents 1.1 FEATURES .......................................................................................................................................... 6 1.2 ACCESSORY PARTS LIST ........................................................................................................
Page 6 - Product Overview; Chapter
6 1. Product Overview Achieve long range surveillance with clarity in virtually any lighting conditions. The amazing low light sensitivity of 0.05 lux before the added benefits of advanced DSP technology, delivered by a 1/3” Sony Super HAD CCD II sensor, is just the beginning with the new EverFocus ...
Page 7 - Accessory Parts List
7 Motion detection for 4 configurable zones. Privacy mask function for 8 configurable zones. Provides digital zoom up to 32x. Cables routed through weatherproof bushing in the bracket to prevent vandalism or other damage. IP66 weather resistant. Operating temperature range -40°C to 50°C/...
Page 11 - Camera Component Description
11 1.5 Camera Component Description EZ650 Component description Bracket Sun shield Fixing screw for sunshield Video output Power connector RS485 terminal Control key selection switch Control key
Page 12 - Back Panel Layout; GND
12 1.6 Back Panel Layout 1. Video Output Connector Connect the video output of the camera to a color monitor or other video devices through a 75 Ohm type coaxial cable with BNC female connector at backside of the camera. 2. Power Input Terminal Connect the appropriate power to each model. N/L is use...
Page 13 - Note; cannot be controlled remotely.; Related Products; IR Illuminator and bracket
13 5. Control key selection switch Switch to OSD to control OSD menu by using the control key or switch to LENS to adjust zooming and focus (please see “2.3.1 Lens setting” and “3. OSD Menu & Configuration” for details). Note : when it is connected to RS485 for keyboard control, please switch to...
Page 14 - Warning; Wiring and Mounting; RG59/5C2V coaxial cable without connector
13 2. Installation This chapter will describe, in general terms, how to install the EZ650 camera. STEPS: 1. Wire and mount the camera. See 2.1 2. Adjust the camera position. See 2.2 3. Adjust Lens. See 2.3 4. Connect to Keyboard (Optional) See 2.4 Warning To prevent electrical shock, turn off the ...
Page 15 - Screws for back panel
14 2. Fix the bracket to wall by using 4 screws. 3. Open camera’s back cover: Loose the 2 screws from the back panel cover, then open the back cover. Screws for back panel Coaxial cable Power cable RS485 cable
Page 16 - coaxial cable
15 4. Take off the cap of waterproof conduit which is at the camera bottom. Note: 1. the holes of waterproof conduit were plugged, please remove the plug when you need to use it for connection. 5. Take coaxial cable, power cable and RS485 cable to pass through waterproof conduit, place them into cam...
Page 19 - Adjusting Camera Position
18 2.2 Adjusting Camera Position Adjust camera’s angle vertically or horizontally by using hex key included in package. Screws for back panel Loose this screw to make angle adjustment vertically Loose this screw to make angle adjustment horizontally
Page 20 - and use this key for; OSD; Please turn the control key selection switch at the back panel to “; Lens
19 2.3 Adjusting Lens Open camera’s base, a control key is attached at inner side of the base. Detach the control key and use this key for OSD or Lens setting. 2.3.1 Lens Setting Please turn the control key selection switch at the back panel to “ Lens ”.( ). Use the control key to do lens setting. T...
Page 22 - Control Key General Operation Guide; Use the control key to do OSD menu setting.
21 3. OSD Menu & Configuration This chapter introduces how to configure the camera OSD menu. 3.1 Control Key General Operation Guide Please turn the control key selection switch at the back panel to “ OSD ” ”( ). Use the control key to do OSD menu setting. I. Bring Up the General OSD Menu Simply...
Page 23 - for further settings. Please refer to the diagram below.; Return to Previous Page; Press the mini-joystick to return to previous page.; Close the Host Menu Screen; To close the menu screen, navigate to the “; EXIT; ” item
22 When the item with sub-menu is selected, press the mini-joystick to switch to the sub-menu for further settings. Please refer to the diagram below. NOTE: For those selected items with “ ” sign in the end, they have the sub-menu for further settings. VI. Return to Previous Page Press the mini-joys...
Page 24 - I. Please turn the control key selection switch at back panel to “
23 3.2 RS485 ID & Baud Rate Setting Note : This section is optional preserved for the people that want to change camera ID and baud rate. In most situations, we suggest you can just use Camera ID-01 and Baud Rate-9600, Protocol-Pelco D on keyboard, then it would work. I. Please turn the control ...
Page 25 - RS485 ID of EZ650 has to be the same as Keyboard’s CAM ID.
24 b. RS485_ID- adjustable 01~128. Default value is 01. Move joystick RIGHT and LEFT to adjust it. RS485 ID of EZ650 has to be the same as Keyboard’s CAM ID. c. BAUD_RATE-adjustable 9600, 4800, 2400 and 1200. Default value is 9600. Move joystick RIGHT and LEFT to adjust it. Baud rate of EZ650 has to...
Page 27 - Default settings are shown bold or in brackets.
26 3.3 OSD Menu Setup 3.3.1 OSD Menu Tree Default settings are shown bold or in brackets. Lens — DC — Brightness 0~100 (50) Exposure — Shutter — x256, x128, x64, x32, x16, x8, x4, x2, 1/60(NTSC) / 1/50 (PAL) , FLK,1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000 — AGC — HIGH ; MIDDLE ; LOW ; OFF — SENS...
Page 29 - MIDDLE; Note: AGC must be on for sense-up low light boost to function.
28 3.3.2 LENS When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by using the UP and DOWN buttons. The iris opening can be adjusted in DC mode in LENS LEVEL. The level can be adjusted from 0 to 50. Please select RETURN and press the SETUP button if you would l...
Page 30 - Set the factory default values for BLC.
29 3.3.3.4 BLC-BACKLIGHT COMPENSATION There are three choices for the type of BLC which may be employed: OFF, traditional BLC or HSBLC. BLC Video gain can be adjusted automatically to correct the exposure of subjects that are in front of a bright light source. Please direct the arrow to point to “BL...
Page 38 - Control from Keyboard EKB500 (Optional); Key Features with Keyboard; OSD can be set up from Keyboard.; OSD Menu Setting by Keyboard; b. Move the joystick UP
37 Control from Keyboard EKB500 (Optional) Note! Before being able to control keyboard, make sure Keyboard RS485 camera ID, Baud rate match the camera. (see COM port setting in EKB500 manual). EZ650 camera ID default is 01. Baud rate is 9600. Support Protocol EVF-1, EVF-2 and Pelco-D. 4.1 Key Featur...
Page 39 - Lens Adjustment by Keyboard; Counterclockwise to zoom in.
38 d. Move the joystick RIGHT ( ) and LEFT ( ) to adjust the mode and parameters of the selected item. e. Press “Menu” to leave and goes to previous menu after setting. Move to “exit” and press “menu” button when you finish all settings. f. For detail setting and every setup function, Please ref...
Page 40 - EverFocus Electronics Corp.
39 EverFocus Electronics Corp. EverFocus Taiwan: 12F, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2698 2380 www.everfocus.com.tw