Page 2 - Operation Instruction
2 E V E R F O C U S E L E C T R O N I C S C O R P O R A T I O N P/N: 4605XZ0610001AR Operation Instruction © 2010 EverFocus Electronics Corp Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was c...
Page 3 - Precautions
3 Precautions 1. Do not install the camera near electric or magnetic fields. Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image. 2. Never disassemble t...
Page 4 - Federal Communication Commission Interference Statement; Reorient or relocate the receiving antenna.; WEE
4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential in...
Page 5 - Table of Contents
5 Table of Contents 1 Product Overview.............................................................................................................................................. 7 1.1 Features ...........................................................................................................
Page 7 - PRODUCT OVERVIEW; Features; Chapter
7 1 PRODUCT OVERVIEW Amazing color low light sensitivity of 0.05 lux before the added benefits of advanced DSP technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new EverFocus EZ610. Get color without compromise: 560TVL resolution, your choice of full motion col...
Page 8 - Accessory Parts List
8 1.2 Accessory Parts List Please be careful when you unpack the box and the electronic device inside. Check and make sure that you have all the items listed below inside the original box: • Camera Unit x 1 • Speedy Mount Ring x 1 • Surface Wire Slot Filler x 1 • Operation Manual x 1 • Video Test Ca...
Page 9 - Specifications
9 1.3 Specifications Model EZ610 Pickup Device 1/3" SONY Super HAD II CCD Video Format NTSC, PAL (by model) Picture Elements 768 x 494(NTSC)/ 752 x 582 (PAL) Horizontal Resolution 560 TVL Sensitivity 0.05Lux/F=1.2 (AGC ON); 0.0002Lux/F=1.2 (Sens-up 256x) S/N Ratio Over 52dB (AGC off) Electronic ...
Page 10 - Dimensions; Camera Base
10 1.4 Dimensions Camera Base Camera Body Front view of EZ610
Page 11 - Camera Component Description; LED will turn red when you select the Menu setting mode.; Related Products; with the camera to achieve the best performance:
11 1.5 Camera Component Description 1) Reset: To load the factory default configuration press the button, which is inside this hole, for 3 seconds. Please gently insert a thin, non-metallic device into the hole to operate the reset button. 2) Control Key: For setting Lens & OSD menu. Press the m...
Page 12 - INSTALLATION; Wiring and Mounting
12 2 INSTALLATION This chapter will describe, in general terms, how to install the EZ610 camera. STEPS: 1. Wire and mount the camera. See 2.1 2. Adjust the camera position. See 2.2 Warning To prevent electrical shock, turn off the electrical power before making electrical connections. 2.1 Wiring and...
Page 14 - Adjust Camera Position; st axis; Use a hexagon key to loosen this screw to
14 2.2 Adjust Camera Position Adjust the viewing angle to the desired direction. With this unique 3-axis positioning system, installers can capture images from virtually any angle, without compromising. The camera can be adjusted in 3 ways. 1st axis 2nd axis Use a hexagon key to loosen this screw to...
Page 15 - Loosen this screw; rd axis; Loosen lock ring and set screw to rotate camera 360°
15 Loosen this screw 3rd axis Sunshield To remove or install the sunshield, use the hexagon wrench provided to loosen the screw at sunshield. Note: When properly installed, the rear of the sunshield is even with the rear of the camera body; improperly extending the sunshield to ‘shade’ the lens can ...
Page 16 - OSD MENU SETUP; Control Key General Operation Guide; Simply press the mini-joystick to bring up the general OSD menu.; Main Menu
16 3 OSD MENU SETUP This chapter introduces how to change RS485 ID and Baud Rate and to configure the camera OSD menu. STEPS If you want to connect camera with keyboard or other RS-485 - controller, please refer to Section 3.2 RS485 ID & Baud Rate setting. Otherwise, please go to STEP 2. Configu...
Page 17 - RS485 ID & Baud Rate Setting; first
17 NOTE: For those selected items with “ ” sign in the end, there is a sub-menu for further settings. Return to Previous Page Go to “Return” by turning the mini-joystick and press the mini-joystick to return to previous page. Close the Host Menu Screen To close the menu screen, navigate to the “EXIT...
Page 18 - OSD Menu Setup; OSD Menu Tree
18 3.3 OSD Menu Setup 3.3.1 OSD Menu Tree Default settings are shown bold or in brackets. Lens — DC Brightness 0~100 (50) Exposure — Shutter — x256, x128, x64, x32, x16, x8, x4, x2, 1/60(NTSC) / 1/50 (PAL) , FLK,1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000 — AGC — HIGH ; MIDDLE ; LOW ; OFF — SENS-U...
Page 20 - Select the shutter mode by pressing the LEFT or RIGHT button.; MIDDLE; Note: AGC must be on for sense-up low light boost to function.
20 3.3.2 LENS When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by using the UP and DOWN buttons. The iris opening can be adjusted in DC mode in LENS LEVEL. The level can be adjusted from 0 to 50. Please select RETURN and press the SETUP button if you would l...
Page 21 - Set the factory default values for BLC.
21 3.3.3.4 BLC-Backlight Compensation. There are three choices for the type of BLC which may be employed: OFF, traditonal BLC or HSBLC. BLC Video gain can be adjusted automatically to correct the exposure of subjects that are in front of a bright light source. Please direct the arrow to point to “BL...
Page 22 - WHITE BALANCE CONTROL
22 LEVEL Adjust the sensitivity level for HSBLC from 0 to 8. DEFAULT Set the factory default values for HSBLC. LEFT/RIGHT Set the Left/Right side of an area for the HSBLC to be adjusted. The value adjustable is 0~6. WIDTH Set the width of an area for the HSBLC to be adjusted. The value adjustable is...
Page 23 - DAY NIGHT
23 ATW Auto Tracking White Balance: This mode can be used within the color temperature range from 5,500°K to 6,000°K (eg, fluorescent light, outdoor, sodium vapor lamp or inside tunnels). AWB Auto White Balance: This mode can be used within the color temperature range from 2,500°K to 10,000°K. (defa...
Page 24 - DNR; ON
24 auto switching function. Delay Delay time for switch reaction on light changes, range 0~63 seconds. S-Level Trigger level for switching to day mode in range 0~100. E-Level Trigger level for switching to night mode in range 0~100. NOTE: The AUTO mode is not recommended for applications with high- ...
Page 25 - SPECIAL
25 3.3.7 SPECIAL In this section, user can do special settings including camera title, digital effects, motion, privacy zones, synchronization and language. Please direct the arrow to point to “SPECIAL” on the SETUP menu by using the UP and DOWN buttons. Select the mode you would like to operate by ...
Page 28 - INT; Internal synchronization; ADJUST; Adjust sharpness, Blue and Red level in this section.
28 3.3.7.11 SYNC There are two SYNCHRONIZATION modes INTERNAL and LINE-LOCK. In LINE-LOCK mode, the video signal is synchronized to the frequency of the incoming AC power. The Line-Lock synchronization can only be used when the supply power is 24VAC 60Hz (NTSC models) or 50Hz (PAL models). INT Inter...
Page 29 - RESET
29 3.3.9 RESET 3.3.9.1 FACTORY RESET Reset to the default settings. Press “RET” to return to the previous menu. Press “END” to exit. 3.3.9.2 EXIT Save all the menu settings and exit. NOTE: If you quit a Menu without pressing EXIT, all the settings you previously modified will NOT be saved.
Page 30 - RS-485 REMOTE CONTROL; Remote control with EKB-500 keyboard; OSD Menu Setting by Keyboard; ). This allows you to move between selection
30 4 RS-485 REMOTE CONTROL 4.1 Remote control with EKB-500 keyboard 4.1.1 RS - 485 Wiring For more details about RS-485 wiring please consult related chapters in EKB-500 user manual. Note! Before being able to control keyboard, make sure Keyboard RS485 camera ID, Baud rate match the camera. (see COM...
Page 31 - ) to adjust the mode and parameters of the; Lens Adjustment by Keyboard; Remote Control with EverFocus DVR; Camera Operation and Setup by DVR; Set Preset 95; Open OSD menu
31 d. Move the joystick RIGHT ( f ) and LEFT ( e ) to adjust the mode and parameters of the selected item. Press “Menu” to leave and goes to previous menu after setting. Move to “exit” and press “menu” button when you finish all settings. For detail setting of each setup function, Please refer to “3...
Page 32 - EverFocus Electronics Corp.; Tokyo
32 EverFocus Electronics Corp. Headquarters Office 12F, No.79 Sec.1 Shin-Tai Wu Road, Hsi-Chi, Taipei, Taiwan Tel: +886-2-26982334 Fax: +886-2-26982380 Beijing office Room 609,Technology Trade Building. Shangdi Information Industry Base, Haidian District,Beijing China Tel: +86-10-62971096 Fax: +86-1...
